Ultrathin Co3O4 Layers with Large Contact Area on Carbon Fibers as High‐Performance Electrode for Flexible Zinc–Air Battery Integrated with Flexible Display

A facile and binder‐free method is developed for the in situ and horizontal growth of ultrathin mesoporous Co₃O₄ layers on the surface of carbon fibers in the carbon cloth (ultrathin Co₃O₄/CC) as high‐performance air electrode for the flexible Zn–air battery. In particular, the ultrathin Co₃O₄ layers have a maximum contact area on the conductive support, facilitating the rapid electron transport and preventing the aggregation of ultrathin layers. The ultrathin feature of Co₃O₄ layers is characterized by the transmission electron microscopy, Raman spectra, and X‐ray absorption fine structure spectroscopy. Benefiting from the high utilization degree of active materials and rapid charge transport, the mass activity for oxygen reduction and evolution reactions of the ultrathin Co₃O₄/CC electrode is more than 10 times higher than that of the carbon cloth loaded with commercial Co₃O₄ nanoparticles. Compared to the commercial Co₃O₄/CC electrode, the flexible Zn–air battery using ultrathin Co₃O₄/CC electrode exhibits excellent rechargeable performance and high mechanical stability. Furthermore, the flexible Zn–air battery is integrated with a flexible display unit. The whole integrated device can operate without obvious performance degradation under serious deformation and even during the cutting process, which makes it highly promising for wearable and roll‐up optoelectronics.     

Graphitic Carbon Nitride Induced Micro‐Electric Field for Dendrite‐Free Lithium Metal Anodes

Uncontrolled dendrites resulting from nonuniform lithium (Li) nucleation/growth and Li volume expansion during charging cause serious safety problems for Li anode‐based batteries. Here the coating of nickel foam with graphitic carbon nitride (g‐C₃N₄) to have a 3D current collector (g‐C₃N₄@Ni foam) for dendrite‐free Li metal anodes is reported. The lithiophilic g‐C₃N₄ coupled with the 3D framework is demonstrated to be highly effective for promoting the uniform deposition of Li and suppressing the formation of dendrites. Both density functional theory calculations and experimental studies indicate the formation of a micro‐electric field resulting from the tri‐s‐triazine units of g‐C₃N₄, which induces numerous Li nuclei during the initial nucleation stage, effectively guiding the following Li growth on the 3D Ni foam to be well distributed. Furthermore, the 3D porous framework is favorable for absorbing any volume change and stabilizing the solid–electrolyte interphase layer during repeated Li plating/stripping. As such, a Li metal anode based on the g‐C₃N₄@Ni foam has a remarkable electrochemical performance with a high Coulombic efficiency (98% retention after 300 cycles), an ultralong lifespan up to 900 h, as well as a low overpotential (<15 mV at 1.0 mA cm^?2) at a Li deposition of 9.0 mA h cm^?2.     

g‐C3N4‐Based Heterostructured Photocatalysts

Photocatalysis is considered as one of the promising routes to solve the energy and environmental crises by utilizing solar energy. Graphitic carbon nitride (g‐C₃N₄) has attracted worldwide attention due to its visible‐light activity, facile synthesis from low‐cost materials, chemical stability, and unique layered structure. However, the pure g‐C₃N₄ photocatalyst still suffers from its low separation efficiency of photogenerated charge carriers, which results in unsatisfactory photocatalytic activity. Recently, g‐C₃N₄‐based heterostructures have become research hotspots for their greatly enhanced charge carrier separation efficiency and photocatalytic performance. According to the different transfer mechanisms of photogenerated charge carriers between g‐C₃N₄ and the coupled components, the g‐C₃N₄‐based heterostructured photocatalysts can be divided into the following categories: g‐C₃N₄‐based conventional type II heterojunction, g‐C₃N₄‐based Z‐scheme heterojunction, g‐C₃N₄‐based p–n heterojunction, g‐C₃N₄/metal heterostructure, and g‐C₃N₄/carbon heterostructure. This review summarizes the recent significant progress on the design of g‐C₃N₄‐based heterostructured photocatalysts and their special separation/transfer mechanisms of photogenerated charge carriers. Moreover, their applications in environmental and energy fields, e.g., water splitting, carbon dioxide reduction, and degradation of pollutants, are also reviewed. Finally, some concluding remarks and perspectives on the challenges and opportunities for exploring advanced g‐C₃N₄‐based heterostructured photocatalysts are presented.     

Catalytic Polysulfide Conversion and Physiochemical Confinement for Lithium–Sulfur Batteries

The lithium–sulfur (Li–S) battery is widely regarded as a promising energy storage device due to its low price and the high earth‐abundance of the materials employed. However, the shuttle effect of lithium polysulfides (LiPSs) and sluggish redox conversion result in inefficient sulfur utilization, low power density, and rapid electrode deterioration. Herein, these challenges are addressed with two strategies 1) increasing LiPS conversion kinetics through catalysis, and 2) alleviating the shuttle effect by enhanced trapping and adsorption of LiPSs. These improvements are achieved by constructing double‐shelled hollow nanocages decorated with a cobalt nitride catalyst. The N‐doped hollow inner carbon shell not only serves as a physiochemical absorber for LiPSs, but also improves the electrical conductivity of the electrode; significantly suppressing shuttle effect. Cobalt nitride (Co₄N) nanoparticles, embedded in nitrogen‐doped carbon in the outer shell, catalyze the conversion of LiPSs, leading to decreased polarization and fast kinetics during cycling. Theoretical study of the Li intercalation energetics confirms the improved catalytic activity of the Co₄N compared to metallic Co catalyst. Altogether, the electrode shows large reversible capacity (1242 mAh g^?1 at 0.1 C), robust stability (capacity retention of 658 mAh g^?1 at 5 C after 400 cycles), and superior cycling stability at high sulfur loading (4.5 mg cm^?2).     

High‐Performance Flexible Solid‐State Ni/Fe Battery Consisting of Metal Oxides Coated Carbon Cloth/Carbon Nanofiber Electrodes

Aqueous Ni/Fe batteries have great potential as flexible energy storage devices, owing to their low cost, low toxicity, high safety, and high energy density. However, the poor cycling stability has limited the widely expected application of Ni/Fe batteries, while the use of heavy metal substrates cannot meet the basic requirement for flexible devices. In this work, a flexible type of solid‐state Ni/Fe batteries with high energy and power densities is rationally developed using needle‐like Fe₃O₄ and flake‐like NiO directly grown on carbon cloth/carbon nanofiber (CC–CF) matrix as the anode and cathode, respectively. The hierarchical CC–CF substrate with high electric conductivity and good flexibility serves as an ideal support for guest active materials of nanocrystalline Fe₃O₄ and NiO, which can effectively buffer the volume change giving rise to good cycling ability. By utilizing a gel electrolyte, a robust and mechanically flexible quasi‐solid‐state Ni/Fe full cell can be assembled. It demonstrates optimal electrochemical performance, such as high energy density (5.2 mWh cm^?3 and 94.5 Wh Kg^?1), high power density (0.64 W cm^?3 and 11.8 KW Kg^?1), together with excellent cycling ability. This work provides an example of solid‐state alkaline battery with high electrochemical performance and mechanical flexibility, holding great potential for future flexible electronic devices.     

Sandwich‐Like Ultrathin TiS2 Nanosheets Confined within N,S Codoped Porous Carbon as an Effective Polysulfide Promoter in Lithium‐Sulfur Batteries

As the lightest member of transition metal dichalcogenides, 2D titanium disulfide (2D TiS₂) nanosheets are attractive for energy storage and conversion. However, reliable and controllable synthesis of single‐ to few‐layered TiS₂ nanosheets is challenging due to the strong tendency of stacking and oxidation of ultrathin TiS₂ nanosheets. This study reports for the first time the successful conversion of Ti₃C₂T_x MXene to sandwich‐like ultrathin TiS₂ nanosheets confined by N, S co‐doped porous carbon (TiS₂@NSC) via an in situ polydopamine‐assisted sulfuration process. When used as a sulfur host in lithium–sulfur batteries, TiS₂@NSC shows both high trapping capability for lithium polysulfides (LiPSs), and remarkable electrocatalytic activity for LiPSs reduction and lithium sulfide oxidation. A freestanding sulfur cathode integrating TiS₂@NSC with cotton‐derived carbon fibers delivers a high areal capacity of 5.9 mAh cm^?2 after 100 cycles at 0.1 C with a low electrolyte/sulfur ratio and a high sulfur loading of 7.7 mg cm^?2, placing TiS₂@NSC one of the best LiPSs adsorbents and sulfur conversion catalysts reported to date. The developed nanospace‐confined strategy will shed light on the rational design and structural engineering of metal sulfides based nanoarchitectures for diverse applications.     

Metal‐Free 2D/2D Heterojunction of Graphitic Carbon Nitride/Graphdiyne for Improving the Hole Mobility of Graphitic Carbon Nitride

The design and synthesis of efficient metal‐free photoelectrocatalysts for water splitting are of great significance, as nonmetal elements are generally earth abundant and environment friendly. As a typical metal‐free semiconductor, g‐C3N4 has received much attention in the field of photocatalytic water splitting. However, the poor photoinduced hole mobility of g‐C₃N₄ restrains its catalytic performance. Herein, for the first time, graphdiyne (GDY) is used to interact with g‐C₃N₄ to construct a metal‐free 2D/2D heterojunction of g‐C₃N₄/GDY as an efficient photoelectrocatalyst for water splitting. The g‐C₃N₄/GDY photocathode exhibits enhanced photocarriers separation due to excellent hole transfer nature of graphdiyne and the structure of 2D/2D heterojunction of g‐C₃N₄/GDY, realizing a sevenfold increase in electron life time (610 μs) compared to that of g‐C₃N₄ (88 μs), and a threefold increase in photocurrent density (?98 μA cm^?2) compared to that of g‐C₃N₄ photocathode (?32 μA cm^?2) at a potential of 0 V versus normal hydrogen electrode (NHE) in neutral aqueous solution. The photoelectrocatalytic performance can be further improved by fabricating Pt@g‐C₃N₄/GDY, which displays an photocurrent of ?133 μA cm^?2 at a potential of 0 V versus NHE in neutral aqueous solution. This work provides a new strategy for the design of efficient metal‐free photoelectrocatalysts for water splitting.     

Ultrafine Co3Se4 Nanoparticles in Nitrogen‐Doped 3D Carbon Matrix for High‐Stable and Long‐Cycle‐Life Lithium Sulfur Batteries

Lithium–sulfur batteries are a promising high energy output solution for substitution of traditional lithium ion batteries. In recent times research in this field has stepped into the exploration of practical applications. However, their applications are impeded by cycling stability and short life‐span mainly due to the notorious polysulfide shuttle effect. In this work, a multifunctional sulfur host fabricated by grafting highly conductive Co₃Se₄ nanoparticles onto the surface of an N‐doped 3D carbon matrix to inhibit the polysulfide shuttle and improve the sulfur utilization is proposed. By regulating the carbon matrix and the Co₃Se₄ distribution, N‐CN‐750@Co₃Se₄‐0.1 m with abundant polar sites is experimentally and theoretically shown to be a good LiPSs absorbent and a sulfur conversion accelerator. The S/N‐CN‐750@Co₃Se₄‐0.1 m cathode shows excellent sulfur utilization, rate performance, and cyclic durability. A prolonged cycling test of the as‐fabricated S/N‐CN‐750@Co₃Se₄‐0.1 m cathode is carried out at 0.2 C for more than 5 months which delivers a high initial capacity of 1150.3 mAh g^?1 and retains 531.0 mAh g^?1 after 800 cycles with an ultralow capacity reduction of 0.067% per cycle, maintaining Coulombic efficiency of more than 99.3%. The reaction details are characterized and analyzed by ex situ measurements. This work highly emphasizes the potential capabilities of transition‐metal selenides in lithium–sulfur batteries.     

A Metal Organic Framework Derived Solid Electrolyte for Lithium–Sulfur Batteries

Lithium–sulfur batteries (LSBs) are currently considered as promising candidates for next‐generation energy storage technologies. However, their practical application is hindered by the critical issue of the polysulfide‐shuttle. Herein, a metal organic framework (MOF)‐derived solid electrolyte is presented to address it. The MOF solid electrolyte is developed based on a Universitetet i Oslo (UIO) structure. By grafting a lithium sulfonate (‐SO₃Li) group to the UIO ligand, both the ionic conductivity and the polysulfide‐suppression capability of the resulting ‐SO₃Li grafted UIO (UIOSLi) solid electrolyte are greatly improved. After integrating a Li‐based ionic liquid (Li‐IL), lithium bis(trifluoromethanesulfonyl)imide in 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide, the resulting Li‐IL/UIOSLi solid electrolyte exhibits an ionic conductivity of 3.3 × 10^?4 S cm^?1 at room temperature. Based on its unique structure, the Li‐IL/UIOSLi solid electrolyte effectively restrains the polysulfide shuttle and suppresses lithium dendritic growth. Lithium–sulfur cells with the Li‐IL/UIOSLi solid electrolyte and a Li₂S₆ catholyte show stable cycling performance that preserves 84% of the initial capacity after 250 cycles with a capacity‐fade rate of 0.06% per cycle.     

Optimized Catalytic WS2–WO3 Heterostructure Design for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries

The lithium–sulfur (Li–S) battery is a next generation high energy density battery, but its practical application is hindered by the poor cycling stability derived from the severe shuttling of lithium polysulfides (LiPSs). Catalysis is a promising way to solve this problem, but the rational design of relevant catalysts is still hard to achieve. This paper reports the WS₂–WO₃ heterostructures prepared by in situ sulfurization of WO₃, and by controlling the sulfurization degree, the structure is controlled, which balances the trapping ability (by WO₃) and catalytic activity (by WS₂) toward LiPSs. As a result, the WS₂–WO₃ heterostructures effectively accelerate LiPS conversion and improve sulfur utilization. The Li–S battery with 5 wt% WS₂–WO₃ heterostructures as additives in the cathode shows an excellent rate performance and good cycling stability, revealing a 0.06% capacity decay each cycle over 500 cycles at 0.5 C. By building an interlayer with such heterostructure‐added graphenes, the battery with a high sulfur loading of 5 mg cm^?2 still shows a high capacity retention of 86.1% after 300 cycles at 0.5 C. This work provides a rational way to prepare the metal oxide–sulfide heterostructures with an optimized structure to enhance the performance of Li–S batteries.     

Blood‐Capillary‐Inspired,Free‐Standing,Flexible, and Low‐Cost Super‐Hydrophobic N‐CNTs@SS Cathodes for High‐Capacity,High‐Rate,and Stable Li‐Air Batteries

With the rising demand for flexible and wearable electronic devices, flexible power sources with high energy densities are required to provide a sustainable energy supply. Theoretically, rechargeable, flexible Li‐O₂/air batteries can provide extremely high specific energy densities; however, the high costs, complex synthetic methods, and inferior mechanical properties of the available flexible cathodes severely limit their practical applications. Herein, inspired by the structure of human blood capillary tissue, this study demonstrates for the first time the in situ growth of interpenetrative hierarchical N‐doped carbon nanotubes on the surface of stainless‐steel mesh (N‐CNTs@SS) for the fabrication of a self‐supporting, flexible electrode with excellent physicochemical properties via a facile and scalable one‐step strategy. Benefitting from the synergistic effects of the high electronic conductivity and stable 3D interconnected conductive network structure, the Li‐O₂ batteries obtained with the N‐CNTs@SS cathode exhibit superior electrochemical performance, including a high specific capacity (9299 mA h g^?1 at 500 mA g^?1), an excellent rate capability, and an exceptional cycle stability (up to 232 cycles). Furthermore, as‐fabricated flexible Li‐air batteries containing the as‐prepared flexible super‐hydrophobic cathode show excellent mechanical properties, stable electrochemical performance, and superior H₂O resistibility, which enhance their potential to power flexible and wearable electronic devices.     

Polysulfide‐Shuttle Control in Lithium‐Sulfur Batteries with a Chemically/Electrochemically Compatible NaSICON‐Type Solid Electrolyte

A NaSICON‐type Li⁺‐ion conductive membrane with a formula of Li_{1+ x} Y _x Zr_{2? x} (PO₄)₃ (LYZP) (x = 0–0.15) has been explored as a solid‐electrolyte/separator to suppress polysulfide‐crossover in lithium‐sulfur (Li‐S) batteries. The LYZP membrane with a reasonable Li⁺‐ion conductivity shows both favorable chemical compatibility with the lithium polysulfide species and exhibits good electrochemical stability under the operating conditions of the Li‐S batteries. Through an integration of the LYZP solid electrolyte with the liquid electrolyte, the hybrid Li‐S batteries show greatly enhanced cyclability in contrast to the conventional Li‐S batteries with the porous polymer (e.g., Celgard) separator. At a rate of C/5, the hybrid Li ||LYZP|| Li₂S₆ batteries developed in this study (with a Li‐metal anode, a liquid/LYZP hybrid electrolyte, and a dissolved lithium polysulfide cathode) delivers an initial discharge capacity of ≈1000 mA h g^?1 (based on the active sulfur material) and retains ≈90% of the initial capacity after 150 cycles with a low capacity fade‐rate of <0.07% per cycle.     

Slurry‐Fabricable Li+‐Conductive Polymeric Binders for Practical All‐Solid‐State Lithium‐Ion Batteries Enabled by Solvate Ionic Liquids

For mass production of all‐solid‐state lithium‐ion batteries (ASLBs) employing highly Li⁺ conductive and mechanically sinterable sulfide solid electrolytes (SEs), the wet‐slurry process is imperative. Unfortunately, the poor chemical stability of sulfide SEs severely restrict available candidates for solvents and in turn polymeric binders. Moreover, the binders interrupt Li⁺‐ionic contacts at interfaces, resulting in the below par electrochemical performance. In this work, a new scalable slurry fabrication protocol for sheet‐type ASLB electrodes made of Li⁺‐conductive polymeric binders is reported. The use of intermediate‐polarity solvent (e.g., dibromomethane) for the slurry allows for accommodating Li₆PS₅Cl and solvate‐ionic‐liquid‐based polymeric binders (NBR‐Li(G3)TFSI, NBR: nitrile?butadiene rubber, G3: triethylene glycol dimethyl ether, LiTFSI: lithium bis(trifluoromethanesulfonyl)imide) together without suffering from undesirable side reactions or phase separation. The LiNi_0.6Co_0.2Mn_0.2O₂ and Li₄Ti₅O₁₂ electrodes employing NBR‐Li(G3)TFSI show high capacities of 174 and 160 mA h g^?1 at 30 °C, respectively, which are far superior to those using conventional NBR (144 and 76 mA h g^?1). Moreover, high areal capacity of 7.4 mA h cm^?2 is highlighted for the LiNi_0.7Co_0.15Mn_0.15O₂ electrodes with ultrahigh mass loading of 45 mg cm^?2. The facilitated Li⁺‐ionic contacts at interfaces paved by NBR‐Li(G3)TFSI are evidenced by the complementary analysis from electrochemical and ⁷Li nuclear magnetic resonance measurements.     

3D Printable Ceramic–Polymer Electrolytes for Flexible High‐Performance Li‐Ion Batteries with Enhanced Thermal Stability

This study establishes an approach to 3D print Li‐ion battery electrolytes with controlled porosity using a dry phase inversion method. This ink formulation utilizes poly(vinyldene fluoride) in a mixture of N‐methyl‐2‐pyrrolidone (good solvent) and glycerol (weak nonsolvent) to generate porosity during a simple drying step. When a nanosized Al₂O₃ filler is included in the ink, uniform sub‐micrometer pore formation is attained. In other words, no additional processing steps such as coagulation baths, stretching, or etching are required for full functionality of the electrolyte, which makes it a viable candidate to enable completely additively manufactured Li‐ion batteries. Compared to commercial polyolefin separators, these electrolytes demonstrate comparable high rate electrochemical performance (e.g., 5 C), but possess better wetting characteristics and enhanced thermal stability. Additionally, this dry phase inversion method can be extended to printable composite electrodes, yielding enhanced flexibility and electrochemical performance over electrodes prepared with only good solvent. Finally, sequentially printing this electrolyte ink over a composite electrode via a direct write extrusion technique has been demonstrated while maintaining expected functionality in both layers. These ink formulations are an enabling step toward completely printed batteries and can allow direct integration of a flexible power source in restricted device areas or on nonplanar surfaces.     

Novel 2D Sb2S3 Nanosheet/CNT Coupling Layer for Exceptional Polysulfide Recycling Performance

2D layer‐structured materials are considered a promising candidate as a coupling material in lithium sulfur batteries (LSBs) due to their high surface‐volume ratio and abundant active binding sites, which can efficiently mitigate shuttling of soluble polysulfides. Herein, an electrochemical Li intercalation and exfoliation strategy is used to prepare 2D Sb₂S₃ nanosheets (SSNSs), which are incorporated onto a separator in LSBs as a new 2D coupling material for the first time. The cells containing a rationally designed separator which is coated with an SSNS/carbon nanotube (CNT) coupling layer deliver a much improved specific capacity with a remarkable 0.05% decay rate for over 200 cycles at a current density of 2 C. The capability of the SSNSs to entrap polysulfides through their favorable interfacial functionality and the high electrical conductivity of the CNT network facilitates recycling of active materials. The first‐principle calculations verify the important roles of SSNSs, which demonstrate ideal binding strengths (1.33–2.14 eV) to entrap Li₂S_x as well as a low‐energy barrier (189 meV) for Li diffusion. These findings offer new insights into discovering novel coupling layers for high‐performance LSBs and shed new light on the application of 2D layer‐structured materials in energy storage systems.     

Alkaline Polymer Membrane‐Based Ultrathin,Flexible, and High‐Performance Solid‐State Zn‐Air Battery

The increasing demand for portable and wearable electronics requires lightweight, thin, and highly flexible power sources, for example, flexible zinc‐air batteries (ZABs). The so‐far reported flexible ZAB devices mostly remain bulky, with a design consisting of two relatively thick substrates (e.g., carbon cloths and/or metal foams) and a gel electrolyte‐coated separator in between. Herein, an ultrathin (≈0.2 mm) solid‐state ZAB with high flexibility and performance is introduced by directly forming self‐standing active layers on each surface of an alkaline polymer membrane through an ink‐casting/hot‐pressing approach. A Fe/N‐doped 3D carbon with hierarchic pores and an interconnected network structure is used as cathode electrocatalyst, so that the backing gas‐diffusion layer (e.g., carbon cloth) can be abandoned. What is further, a microstructure‐modulating method to significantly increase the FeN₄ active sites for oxygen reduction reaction is developed, thus significantly boosting the performance of the ZAB. The assembled solid‐state ZAB manifests remarkable peak power density of 250 mW cm^?3 and high capacity of 150.4 mAh cm^?3 at 8.3 mA cm^?3, as well as excellent flexibility. The new design should provide valuable opportunity to the portable and wearable electronics.     

Freestanding Flexible Li2S Paper Electrode with High Mass and Capacity Loading for High‐Energy Li–S Batteries

Lithium–sulfur (Li–S) batteries are a very appealing power source with extremely high energy density. But the use of a metallic‐Li anode causes serious safety hazards, such as short‐circuiting and explosion of the cells. Replacing a sulfur cathode with a fully‐lithiated lithium sulfide (Li₂S) to pair with metallic‐Li‐free high‐capacity anodes paves a feasible way to address this issue. However, the practical utility of Li₂S cathodes faces the challenges of poor conductivity, sluggish activation process, and high sensitivity to moisture and oxygen that make electrode production more difficult than dealing with sulfur cathodes. Here, an efficient but low‐cost strategy for easy production of freestanding flexible Li₂S‐based paper electrodes with very high mass and capacity loading in terms of in situ carbonthermal reduction of Li₂SO₄ by electrospinning carbon is reported. This chemistry enables high loading but strong affinity of ultrafine Li₂S nanoparticles in a freestanding conductive carbon‐nanofiber network, meanwhile greatly reducing the manufacturing complexity and cost of Li₂S cathodes. Benefiting from enhanced structural stability and reaction kinetics, the areal specific capacities of such cathodes can be significantly boosted with less sacrificing of high‐rate and cycling capability. This unique Li₂S‐cathode design can be directly applied for constructing metallic‐Li‐free or flexible Li–S batteries with high‐energy density.     

Facile Patterning of Laser‐Induced Graphene with Tailored Li Nucleation Kinetics for Stable Lithium‐Metal Batteries

A facile and scalable approach is reported to stabilize the lithium‐metal anode by regulating the Li nucleation and deposition kinetics with laser‐induced graphene (LIG). By processing polyimide (PI) films on copper foils with a laser, a 3D‐hierarchical composite material is constructed, consisting of a highly conductive copper substrate, a pillared array of flexible PI, and most importantly, porous LIG on the walls of the PI pillars. The high number of defects and heteroatoms present in LIG significantly lowers the Li nucleation barrier compared to the copper foil. An overpotential‐free Li nucleation process is identified at current densities lower than 0.2 mA cm^?2. Theoretical computations reveal that the defects serve as nucleation centers during the heterogeneous nucleation of lithium. By adopting such composites, ultrastable lithium‐metal anodes are obtained with high Coulombic efficiencies of ≈99%. Full lithium‐metal cells based on LiFePO₄ cathodes with a material loading of ≈15 mg cm^?2 and a negative/positive ratio of 5/1 could be cycled over 250 times with a capacity loss of less than 10%. The current work highlights the importance of nucleation kinetics on the stability of metallic anodes and demonstrates a practical method toward long lasting Li‐metal batteries.     

Double‐Shelled NiO‐NiCo2O4 Heterostructure@Carbon Hollow Nanocages as an Efficient Sulfur Host for Advanced Lithium–Sulfur Batteries

Double‐shelled NiO‐NiCo₂O₄ heterostructure@carbon hollow nanocages as efficient sulfur hosts are synthesized to overcome the barriers of lithium–sulfur (Li–S) batteries simultaneously. The double‐shelled nanocages can prevent the diffusion of lithium polysulfides (LiPSs) effectively. NiO‐NiCo₂O₄ heterostructure is able to promote polysulfide conversion reactions. Furthermore, the thin carbon layer outside can improve the electrical conductivity during cycling. Besides, such unique double‐shelled hollow nanocage architecture can also accommodate the volumetric effect of sulfur upon cycling. As a result, the prepared S/NiO‐NiCo₂O₄@carbon (C) electrode exhibits good rate capacities and stable cycling life up to 500 cycles at 0.5 C with a very low capacity decay rate of only ≈0.059% per cycle.     

Highly Tough,Li‐Metal Compatible Organic–Inorganic Double‐Network Solvate Ionogel

Ionogels are considered promising electrolytes for safe lithium‐ion batteries (LIBs) because of their low flammability, good thermal stability, and wide electrochemical stability window. Conventional ionic liquid‐based ionogels, however, face two main challenges; poor mechanical property and low Li‐ion transfer number. In this work, a novel solvate ionogel electrolyte (SIGE) based on an organic–inorganic double network (DN) is designed and fabricated through nonhydrolytic sol–gel reaction and in situ polymerization processes. The unprecedented SIGE possesses high toughness (bearing the deformation under the pressure of 80 MPa without damage), high Li‐ion transfer number of 0.43, and excellent Li‐metal compatibility. As expected, the LiFePO₄/Li cell using the newly developed SIGE delivers a high capacity retention of 95.2% over 500 cycles, and the average Coulombic efficiency is as high as 99.8%. Moreover, the Ni‐rich LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811)/Li cell based on the modified SIGE achieves a high Coulombic efficiency of 99.4%, which outperforms previous solid/quasi‐solid‐state NCM811‐based LIBs. Interestingly, the SIGE‐based pouch cells are workable under extreme conditions (e.g., severely deforming or clipping into segments). In terms of those unusual features, the as‐obtained SIGE holds great promise for next‐generation flexible and safe energy‐storage devices.