Structural Insight into Layer Gliding and Lattice Distortion in Layered Manganese Oxide Electrodes for Potassium‐Ion Batteries

Potassium‐ion batteries (PIBs) are an emerging, affordable, and environmentally friendly alternative to lithium‐ion batteries, with their further development driven by the need for suitably performing electrode materials capable of reversibly accommodating the relatively large K⁺. Layer‐structured manganese oxides are attractive as electrodes for PIBs, but suffer from structural instability and sluggish kinetics of K⁺ insertion/extraction, leading to poor rate capability. Herein, cobalt is successfully introduced at the manganese site in the K_xMnO₂ layered oxide electrode material and it is shown that with only 5% Co, the reversible capacity increases by 30% at 22 mA g^‐1 and by 92% at 440 mA g^‐1. In operando synchrotron X‐ray diffraction reveals that Co suppresses Jahn–Teller distortion, leading to more isotropic migration pathways for K⁺ in the interlayer, thus enhancing the ionic diffusion and consequently, rate capability. The detailed analysis reveals that additional phase transitions and larger volume change occur in the Co‐doped material as a result of layer gliding, with these associated with faster capacity decay, despite the overall capacity remaining higher than the pristine material, even after 500 cycles. These results assert the importance of understanding the detailed structural evolution that underpins performance that will inform the strategic design of electrode materials for high‐performance PIBs.     

Nanosheets‐Assembled CuSe Crystal Pillar as a Stable and High‐Power Anode for Sodium‐Ion and Potassium‐Ion Batteries

Thanks to low costs and the abundance of the resources, sodium‐ion (SIBs) and potassium‐ion batteries (PIBs) have emerged as leading candidates for next‐generation energy storage devices. So far, only few materials can serve as the host for both Na⁺ and K⁺ ions. Herein, a cubic phase CuSe with crystal‐pillar‐like morphology (CPL‐CuSe) assembled by the nanosheets are synthesized and its dual functionality in SIBs and PIBs is comprehensively studied. The electrochemical measurements demonstrate that CPL‐CuSe enables fast Na⁺ and K⁺ storage as well as the sufficiently long duration. Specifically, the anode delivers a specific capacity of 295 mA h g^?1 at current density of 10 A g^?1 in SIBs, while 280 mA h g^?1 at 5 A g^?1 in PIBs, as well as the high capacity retention of nearly 100% over 1200 cycles and 340 cycles, respectively. Remarkably, CPL‐CuSe exhibits a high initial coulombic efficiency of 91.0% (SIBs) and 92.4% (PIBs), superior to most existing selenide anodes. A combination of in situ X‐ray diffraction and ex situ transmission electron microscopy tests fundamentally reveal the structural transition and phase evolution of CuSe, which shows a reversible conversion reaction for both cells, while the intermediate products are different due to the sluggish K⁺ insertion reaction.     

Hollandite‐Type VO1.75(OH)0.5: Effective Sodium Storage for High‐Performance Sodium‐Ion Batteries

Nanosized hollandite‐type VO_1.75(OH)_0.5 is introduced as a novel cathode material for Na‐ion batteries. Structural investigation based on X‐ray diffraction and Rietveld refinement suggests the presence of numerous vacant sites for Na⁺ intercalation in the VO_1.75(OH)_0.5 structure. All of the possible Na⁺ sites and tunnel‐type Na⁺ diffusion pathways along the c‐axis are confirmed by bond‐valence‐sum analyses. The nanosized hollandite‐type VO_1.75(OH)_0.5 delivers an unexpectedly high specific capacity of ≈351 mAh g^?1 at 15.5 mA g^?1 in the voltage range of 1.0–3.7 V (vs Na⁺/Na), which agrees well with the results predicted by first‐principles calculations. In addition, combined studies using first‐principles calculations and several experimental techniques including in situ operando X‐ray diffraction and ex situ X‐ray absorption spectroscopy confirm that the nanosized hollandite‐type VO_1.75(OH)_0.5 undergoes a single‐phase reaction with a capacity retention of 71% over 200 cycles. Furthermore, the open structure and nanosized particles of hollandite‐type VO_1.75(OH)_0.5 contribute to its excellent power capability with 56% of the capacity measured at 0.05 C being delivered at 7 C.     

A High‐Performance Composite Electrode for Vanadium Redox Flow Batteries

A composite electrode composed of reduced graphene oxide‐graphite felt (rGO‐GF) with excellent electrocatalytic redox reversibility toward V²⁺/V³⁺ and VO²⁺/VO₂⁺ redox couples in vanadium batteries was fabricated by a facile hydrothermal method. Compared with the pristine graphite felt (GF) electrode, the rGO‐GF composite electrode possesses abundant oxygen functional groups, high electron conductivity, and outstanding stability. Its corresponding energy efficiency and discharge capacity are significantly increased by 20% and 300%, respectively, at a high current density of 150 mA cm^?2. Moreover, a discharge capacity of 20 A h L^?1 is obtained with a higher voltage efficiency (74.5%) and energy efficiency (72.0%), even at a large current density of 200 mA cm^?2. The prepared rGO‐GF composite electrode holds great promise as a high‐performance electrode for vanadium redox flow battery (VRFB).     

Localized High‐Concentration Electrolytes Boost Potassium Storage in High‐Loading Graphite

Reversible intercalation of potassium‐ion (K⁺) into graphite makes it a promising anode material for rechargeable potassium‐ion batteries (PIBs). However, the current graphite anodes in PIBs often suffer from poor cyclic stability with low coulombic efficiency. A stable solid electrolyte interphase (SEI) is necessary for stabilizing the large interlayer expansion during K⁺ insertion. Herein, a localized high‐concentration electrolyte (LHCE) is designed by adding a highly fluorinated ether into the concentrated potassium bis(fluorosulfonyl)imide/dimethoxyethane, which forms a durable SEI on the graphite surface and enables highly reversible K⁺ intercalation/deintercalation without solvent cointercalation. Furthermore, this LHCE shows a high ionic conductivity (13.6 mS cm^?1) and excellent oxidation stability up to 5.3 V (vs K⁺/K), which enables compatibility with high‐voltage cathodes. The kinetics study reveals that K⁺ intercalation/deintercalation does not follow the same pathway. The potassiated graphite exhibits excellent depotassiation rate capability, while the formation of a low stage intercalation compound is the rate‐limiting step during potassiation.     

Confined Fe2VO4⊂Nitrogen‐Doped Carbon Nanowires with Internal Void Space for High‐Rate and Ultrastable Potassium‐Ion Storage

Developing low‐cost, high‐capacity, high‐rate, and robust earth‐abundant electrode materials for energy storage is critical for the practical and scalable application of advanced battery technologies. Herein, the first example of synthesizing 1D peapod‐like bimetallic Fe₂VO₄ nanorods confined in N‐doped carbon porous nanowires with internal void space (Fe₂VO₄?NC nanopeapods) as a high‐capacity and stable anode material for potassium‐ion batteries (KIBs) is reported. The peapod‐like Fe₂VO₄?NC nanopeapod heterostructures with interior void space and external carbon shell efficiently prevent the aggregation of the active materials, facilitate fast transportation of electrons and ions, and accommodate volume variation during the cycling process, which substantially boosts the rate and cycling performance of Fe₂VO₄. The Fe₂VO₄?NC electrode exhibits high reversible specific depotassiation capacity of 380 mAh g^?1 at 100 mA g^?1 after 60 cycles and remarkable rate capability as well as long cycling stability with a high capacity of 196 mAh g^?1 at 4 A g^?1 after 2300 cycles. The first‐principles calculations reveal that Fe₂VO₄?NC nanopeapods have high ionic/electronic conductivity characteristics and low diffusion barriers for K⁺‐intercalation. This study opens up new way for investigating high‐capacity metal oxide as high‐rate and robust electrode materials for KIBs.     

A New Strategy for High‐Voltage Cathodes for K‐Ion Batteries: Stoichiometric KVPO4F

The exploration of high‐energy‐density cathode materials is vital to the practical use of K‐ion batteries. Layered K‐metal oxides have too high a voltage slope due to their large K⁺–K⁺ interaction, resulting in low specific capacity and average voltage. In contrast, the 3D arrangement of K⁺, with polyanions separating them, reduces the strength of the effective K⁺‐K⁺ repulsion, which in turn increases specific capacity and voltage. Here, stoichiometric KVPO₄F for use as a high‐energy‐density K‐ion cathode is developed. The KVPO₄F cathode delivers a reversible capacity of ≈105 mAh g^?1 with an average voltage of ≈4.3 V (vs K/K⁺), resulting in a gravimetric energy density of ≈450 Wh kg^?1. During electrochemical cycling, the K_xVPO₄F cathode goes through various intermediate phases at x = 0.75, 0.625, and 0.5 upon K extraction and reinsertion, as determined by ex situ X‐ray diffraction characterization and ab initio calculations. This work further explains the role of oxygen substitution in KVPO_4+xF_1?x: the oxygenation of KVPO₄F leads to an anion‐disordered structure which prevents the formation of K⁺/vacancy orderings without electrochemical plateaus and hence to a smoother voltage profile.     

K‐Birnessite Electrode Obtained by Ion Exchange for Potassium‐Ion Batteries: Insight into the Concerted Ionic Diffusion and K Storage Mechanism

Novel and low‐cost rechargeable batteries are of considerable interest for application in large‐scale energy storage systems. In this context, K‐Birnessite is synthesized using a facile solid‐state reaction as a promising cathode for potassium‐ion batteries. During synthesis, an ion exchange protocol is applied to increase K content in the K‐Birnessite electrode, which results in a reversible capacity as high as 125 mAh g^?1 at 0.2 C. Upon K⁺ exchange the reversible phase transitions are verified by in situ X‐ray diffraction (XRD) characterization. The underlying mechanism is further revealed to be the concerted K⁺ ion diffusion with quite low activation energies by first‐principle simulations. These new findings provide new insights into electrode process kinetics, and lay a solid foundation for material design and optimization of potassium‐ion batteries for large‐scale energy storage.     

Polyanionic Cathode Materials: A Comparison Between Na-Ion and K-Ion Batteries

Sodium-ion batteries (SIBs) and potassium-ion batteries (PIBs) are considered the next-generation candidates for future energy storage systems to partially substitute commercial lithium-ion batteries because of their abundant sodium/potassium reserves, cost-effectiveness, and high safety. Polyanionic cathode materials are widely used in alkali ion batteries due to their stable structural framework, high thermal stability, excellent alkali ion diffusion kinetics, and adjustable working voltage. Generally, the polyanionic cathodes used for SIBs surpass PIBs in the aspect of energy density and cycle life in most cases, however, the PIBs also have their unique advantages that are seldom reported. To this end, the polyanionic materials are classified by the valence states of active metal sites, the storage mechanism of Na⁺ and K⁺ in different crystal structures is summarized, and the electrochemical performance between SIBs and PIBs is compared. Particularly, some unique advantages of polyanionic cathodes in PIBs, such as high working voltage, superior rate capability, and excellent capacity retention are revealed, and the possible reasons are discussed in detail. Finally, various viable solutions are proposed to improve the battery performance of polyanionic compounds for future development.     

Controlled SnO2 Crystallinity Effectively Dominating Sodium Storage Performance

The exploration of sodium ion batteries (SIBs) is a profound challenge due to the rich sodium abundance and limited supply of lithium on earth. Here, amorphous SnO₂/graphene aerogel (a‐SnO₂/GA) nanocomposites have been successfully synthesized via a hydrothermal method for use as anode materials in SIBs. The designed annealing process produces crystalline SnO₂/graphene aerogel (c‐SnO₂/GA) nanocomposites. For the first time, the significant effects of SnO₂ crystallinity on sodium storage performance are studied in detail. Notably, a‐SnO₂/GA is more effective than c‐SnO₂/GA in overcoming electrode degradation from large volume changes associated with charge–discharge processes. Surprisingly, the amorphous SnO₂ delivers a high specific capacity of 380.2 mAh g^?1 after 100 cycles at a current density of 50 mA g^?1, which is almost three times as much as for crystalline SnO₂ (138.6 mAh g^?1). The impressive electrochemical performance of amorphous SnO₂ can be attributed to the intrinsic isotropic nature, the enhanced Na⁺ diffusion coefficient, and the strong interaction between amorphous SnO₂ and GA. In addition, amorphous SnO₂ particles with the smaller size better function to relieve the volume expansion/shrinkage. This study provides a significant research direction aiming to increase the electrochemical performance of the anode materials used in SIBs.     

Interlayer-Engineering and Surface-Substituting Manganese-Based Self-Evolution for High-Performance Potassium Cathode

Manganese-based layered oxides cathodes have attracted enormous interest due to their advantages in cost and energy density. The significant challenges of Mn-based layered oxides for potassium-ion batteries (PIBs) are complex phase transition and Mn dissolution upon K⁺ intercalation/deintercalation. Here, a P3-type K_0.45Rb_0.05Mn_0.85Mg_0.15O₂ (KRMMO) cathode material is proposed to address the above challenges. The results show that rubidium acts as a pillar to expand interlayer spacing and stabilize the structure, while magnesium partially replaces Mn to suppress the Jahn–Teller distortion of the Mn³⁺. The KRMMO cathode exhibits high capacity of 108.0 and 77.3 mAh g⁻¹ at 20 and 500 mA g⁻¹, respectively, and retains 98.2% of its initial capacity after 200 cycles. Compared with P3-K_0.5MnO₂, the capacity fading of P3-KRMMO is effectively suppressed, which is mainly due to the synergistic contribution of Rb and Mg ions in the alleviation of volume change and suppression of phase transition. This work may open a new avenue for the design and optimization of layered cathode materials for PIBs and beyond.     

Realizing Three‐Electron Redox Reactions in NASICON‐Structured Na3MnTi(PO4)3 for Sodium‐Ion Batteries

Developing multielectron reaction electrode materials is essential for achieving high specific capacity and high energy density in secondary batteries; however, it remains a great challenge. Herein, Na₃MnTi(PO₄)₃/C hollow microspheres with an open and stable NASICON framework are synthesized by a spray‐drying‐assisted process. When applied as a cathode material for sodium‐ion batteries, the resultant Na₃MnTi(PO₄)₃/C microspheres demonstrate fully reversible three‐electron redox reactions, corresponding to the Ti^3+/4+ (≈2.1 V), Mn^2+/3+ (≈3.5 V), and Mn^3+/4+ (≈4.0 V vs Na⁺/Na) redox couples. In situ X‐ray diffraction results reveals that both solid‐solution and two‐phase electrochemical reactions are involved in the sodiation/desodiation processes. The high specific capacity (160 mAh g^?1 at 0.2 C), outstanding cyclability (≈92% capacity retention after 500 cycles at 2 C), and the facile synthesis make the Na₃MnTi(PO₄)₃/C a prospective cathode material for sodium‐ion batteries.     

Graphitic Carbon Nanocage as a Stable and High Power Anode for Potassium‐Ion Batteries

As an emerging electrochemical energy storage device, potassium‐ion batteries (PIBs) have drawn growing interest due to the resource‐abundance and low cost of potassium. Graphite‐based materials, as the most common anodes for commercial Li‐ion batteries, have a very low capacity when used an anode for Na‐ion batteries, but they show reasonable capacities as anodes for PIBs. The practical application of graphitic materials in PIBs suffers from poor cyclability, however, due to the large interlayer expansion/shrinkage caused by the intercalation/deintercalation of potassium ions. Here, a highly graphitic carbon nanocage (CNC) is reported as a PIBs anode, which exhibits excellent cyclability and superior depotassiation capacity of 175 mAh g^?1 at 35 C. The potassium storage mechanism in CNC is revealed by cyclic voltammetry as due to redox reactions (intercalation/deintercalation) and double‐layer capacitance (surface adsorption/desorption). The present results give new insights into structural design for graphitic anode materials in PIBs and understanding the double‐layer capacitance effect in alkali metal ion batteries.     

Involvement of extracellular oxidative burst in salicylic acid-induced stomatal closure in Arabidopsis

Salicylic acid (SA), a ubiquitous phenolic phytohormone, is involved in many plant physiological processes including stomatal movement. We analysed SA‐induced stomatal closure, production of reactive oxygen species (ROS) and nitric oxide (NO), cytosolic calcium ion ([Ca²⁺]_cyt) oscillations and inward‐rectifying potassium (K⁺_in) channel activity in Arabidopsis. SA‐induced stomatal closure was inhibited by pre‐treatment with catalase (CAT) and superoxide dismutase (SOD), suggesting the involvement of extracellular ROS. A peroxidase inhibitor, SHAM (salicylhydroxamic acid) completely abolished SA‐induced stomatal closure whereas neither an inhibitor of NADPH oxidase (DPI) nor atrbohD atrbohF mutation impairs SA‐induced stomatal closures. 3,3′‐Diaminobenzidine (DAB) and nitroblue tetrazolium (NBT) stainings demonstrated that SA induced H₂O₂ and O₂^– production. Guard cell ROS accumulation was significantly increased by SA, but that ROS was suppressed by exogenous CAT, SOD and SHAM. NO scavenger 2‐(4‐carboxyphenyl)‐4,4,5,5‐tetramethylimidazoline‐1‐oxyl‐3‐oxide (cPTIO) suppressed the SA‐induced stomatal closure but did not suppress guard cell ROS accumulation whereas SHAM suppressed SA‐induced NO production. SA failed to induce [Ca²⁺]_cyt oscillations in guard cells whereas K⁺_in channel activity was suppressed by SA. These results indicate that SA induces stomatal closure accompanied with extracellular ROS production mediated by SHAM‐sensitive peroxidase, intracellular ROS accumulation and K⁺_in channel inactivation.     

A Layered Inorganic–Organic Open Framework Material as a 4 V Positive Electrode with High‐Rate Performance for K‐Ion Batteries

K‐ion batteries (KIBs) are promising for large‐scale energy storage owing to various advantages like the high abundance of potassium resources in the Earth's crust, high operational potentials, and high power due to fast diffusion of K⁺ ions. However, to realize the practical application of KIBs, electrode materials are needed with high operational voltage, good capacity, long cycle life, and low‐cost. This work reports a layered open framework material, K₂[(VOHPO₄)₂(C₂O₄)], composited with reduced graphene oxide (rGO) as a 4 V positive electrode material for KIBs. The material is prepared by a simple precipitation reaction at room temperature. The material demonstrates reversible K‐extraction/insertion with conventional carbonate ester KPF₆ solutions; however, with low specific capacity and low Coulombic efficiency. A high discharge capacity of >100 mAh g^?1 with good cycling stability and higher Coulombic efficiency is achieved in a highly concentrated electrolyte, 7 mol kg^?1 of potassium bis(fluorosulfonyl)amide (KFSA) in dimethoxyethane (DME) at 0.1 C rate. Due to the facile migration of K⁺ ions in the framework, the material exhibits excellent rate capability with a discharge capacity of 80 mAh g^?1 at 10 C rate, and a good capacity retention of 67% after 500 cycles at 2 C rate.     

Unveiling the Unique Phase Transformation Behavior and Sodiation Kinetics of 1D van der Waals Sb2S3 Anodes for Sodium Ion Batteries

Carbon‐coated van der Waals stacked Sb₂S₃ nanorods (SSNR/C) are synthesized by facile hydrothermal growth as anodes for sodium ion batteries (SIBs). The sodiation kinetics and phase evolution behavior of the SSNR/C anode during the first and subsequent cycles are unraveled by coupling in situ transmission electron microscopy analysis with first‐principles calculations. During the first sodiation process, Na⁺ ions intercalate into the Sb₂S₃ crystals with an ultrafast speed of 146 nm s^?1. The resulting amorphous Na_x Sb₂S₃ intermediate phases undergo sequential conversion and alloying reactions to form crystalline Na₂S, Na₃Sb, and minor metallic Sb. Upon desodiation, Na⁺ ions extract from the nanocrystalline phases to leave behind the fully desodiated Sb₂S₃ in an amorphous state. Such unique phase evolution behavior gives rise to superb electrochemical performance and leads to an unexpectedly small volume expansion of ≈54%. The first‐principles calculations reveal distinctive phase evolution arising from the synergy between the extremely low Na⁺ ion diffusion barrier of 190 meV and the sharply increased electronic conductivity upon the formation of amorphous Na_x Sb₂S₃ intermediate phases. These findings highlight an anomalous Na⁺ ion storage mechanism and shed new light on the development of high performance SIB anodes based on van der Waals crystals.     

Greater sensitivity to vanadate of rat renal relative to cardiac (Na++K+)-ATPase

Vanadate (VO₄^?3) produces a positive inotropic effect in rats and also promotes diuresis as well as natriuresis. Although the mechanism(s) of these effects is uncertain, in the kidney, VO₄^?3 may act through inhibition of (Na⁺+K⁺)-ATPase activity, whereas in the heart, other or additional mechanisms are likely. Under the assay conditions used in the present study, microsomal (Na⁺+K⁺)-ATPase activities from rat kidney cortex and medulla were inhibited to a greater extent than was left ventricular (Na⁺+K⁺)-ATPase activity over a range of VO₄^?3 concentrations. The apparent dissociation constant for left ventricular (Na⁺+K⁺)-ATPase (10.95 ± 1.26 × 10^?7M VO₄^?3) was significantly greater than that of (Na⁺+K⁺)-ATPase from the cortex (3.46±0.96×10^?7 M VO₄^?3) or the medulla (3.32±0.7×10^?7M VO₄^?3, N=6, P<.05) whereas there were no significant differences between the effects of VO₄^?3 on (Na⁺+K⁺)-ATPase from the cortex and medulla. The greater inhibition by VO₄, of (Na⁺+K⁺)-ATPase from the cortex relative to that of the left ventricle, occurred over a range of Na⁺ and K⁺ concentrations, and K⁺ enhanced the inhibition by VO₄^?3 to a greater extent for (Na⁺+K⁺)-ATPase from the cortex than the left ventricle. These results suggest that renal (Na⁺+K⁺)-ATPase is more sensitive than left ventricular (Na⁺+K⁺)-ATPase to inhibition by VO₄^?3 and would, therefore, be more likely to be modulated $\text{in}$$\text{vivo.}$     

Li+ Pre‐Insertion Leads to Formation of Solid Electrolyte Interface on TiO2 Nanotubes That Enables High‐Performance Anodes for Sodium Ion Batteries

Recently, sodium ion batteries (SIBs) have been widely investigated as one of the most promising candidates for replacing lithium ion batteries (LIBs). For SIBs or LIBs, designing a stable and uniform solid electrolyte interphase (SEI) at the electrode–electrolyte interface is the key factor to provide high capacity, long‐term cycling, and high‐rate performance. In this paper, it is described how a remarkably enhanced SEI layer can be obtained on TiO₂ nanotube (TiO₂ NTs) arrays that allows for a strongly improved performance of sodium battery systems. Key is that a Li⁺ pre‐insertion in TiO₂ NTs can condition the SEI for Na⁺ replacement. SIBs constructed with Li‐pre‐inserted NTs deliver an exceptional Na⁺ cycling stability (e.g., 99.9 ± 0.1% capacity retention during 250 cycles at a current rate of 50 mA g^?1) and an excellent rate capability (e.g., 132 mA h g^?1 at a current rate of 1 A g^?1). The key factor in this outstanding performance is that Li‐pre‐insertion into TiO₂ NTs leads not only to an enhanced electronic conductivity in the tubes, but also expands the anatase lattice for facilitated subsequent Na⁺ cycling.     

Vanadate inhibition of the Ca-ATPase from human red cell membranes

1. (1) VO₃⁻ combines with high affinity to the Ca²⁺-ATPase and fully inhibits Ca²⁺-ATPase and Ca²⁺-phosphatase activities. Inhibition is associated with a parallel decrease in the steady-state level of the Ca²⁺-dependent phosphoenzyme.

2. (2) VO₃⁻ blocks hydrolysis of ATP at the catalytic site. The sites for VO₃⁻ also exhibit negative interactions in affinity with the regulatory sites for ATP of the Ca²⁺-ATPase.

3. (3) The sites for VO₃⁻ show positive interactions in affinity with sites for Mg²⁺ and K⁺. This accounts for the dependence on Mg²⁺ and K⁺ of the inhibition by VO₃⁻. Although, with less effectiveness, Na⁺ substitutes for K⁺ whereas Li⁺ does not. The apparent affinities for Mg²⁺ and K⁺ for inhibition by VO₃⁻ seem to be less than those for activation of the Ca²⁺-ATPase.

4. (4) Inhibition by VO₃⁻ is independent of Ca²⁺ at concentrations up to 50 μM. Higher concentrations of Ca²⁺ lead to a progressive release of the inhibitory effect of VO₃⁻.

Construction of Hierarchical K1.39Mn3O6 Spheres via AlF3 Coating for High‐Performance Potassium‐Ion Batteries

Potassium‐ion batteries are attracting great interest for emerging large‐scale energy storage owing to their advantages such as low cost and high operational voltage. However, they are still suffering from poor cycling stability and sluggish thermodynamic kinetics, which inhibits their practical applications. Herein, the synthesis of hierarchical K_1.39Mn₃O₆ microspheres as cathode materials for potassium‐ion batteries is reported. Additionally, an effective AlF₃ surface coating strategy is applied to further improve the electrochemical performance of K_1.39Mn₃O₆ microspheres. The as‐synthesized AlF₃ coated K_1.39Mn₃O₆ microspheres show a high reversible capacity (about 110 mA h g^?1 at 10 mA g^?1), excellent rate capability, and cycling stability. Galvanostatic intermittent titration technique results demonstrate that the increased diffusion kinetics of potassium‐ion insertion and extraction during discharge and charge processes benefit from both the hierarchical sphere structure and surface modification. Furthermore, ex situ X‐ray diffraction measurements reveal that the irreversible structure evolution can be significantly mitigated via surface modification. This work sheds light on rational design of high‐performance cathode materials for potassium‐ion batteries.