Highly Solvating Electrolytes for Lithium–Sulfur Batteries

There is a critical need to evaluate lithium–sulfur (Li–S) batteries with practically relevant high sulfur loadings and minimal electrolyte. Under such conditions, the concentration of soluble polysulfide intermediates in the electrolyte drastically increases, which can alter the fundamental nature of the solution‐mediated discharge and thereby the total sulfur utilization. In this work, an investigation into various high donor number (DN) electrolytes that allow for increased polysulfide dissolution is presented, and the way in which this property may in fact be necessary for increasing sulfur utilization at low electrolyte and high loading conditions is demonstrated. The solvents dimethylacetamide, dimethyl sulfoxide, and 1‐methylimidazole are holistically evaluated against dimethoxyethane as electrolyte co‐solvents in Li–S cells, and they are used to investigate chemical and electrochemical properties of polysulfide species at both dilute and practically relevant conditions. The nature of speciation exhibited by lithium polysulfides is found to vary significantly between these concentrations, particularly with regard to the S₃^?? species. Furthermore, the extent of the instability in conventional electrolyte solvents and high DN solvents with both lithium metal and polysulfides is thoroughly investigated. These studies establish a basis for future efforts into rationally designing an optimal electrolyte for a lean electrolyte, high energy density Li–S battery.     

High‐Fluorinated Electrolytes for Li–S Batteries

Rechargeable Li–S batteries are regarded as one of the most promising next‐generation energy‐storage systems. However, the inevitable formation of Li dendrites and the shuttle effect of lithium polysulfides significantly weakens electrochemical performance, preventing its practical application. Herein, a new class of localized high‐concentration electrolyte (LHCE) enabled by adding inert fluoroalkyl ether of 1H,1H,5H‐octafluoropentyl‐1,1,2,2‐tetrafluoroethyl ether into highly‐concentrated electrolytes (HCE) lithium bis(fluorosulfonyl) imide/dimethoxyether (DME) system is reported to suppress Li dendrite formation and minimize the solubility of the high‐order polysulfides in electrolytes, thus reducing the amount of electrolyte in cells. Such a unique LHCE can achieve a high coulombic efficiency of Li plating/stripping up to 99.3% and completely suppressing the shuttling effect, thus maintaining a S cathode capacity of 775 mAh g^?1 for 150 cycles with a lean electrolyte of 4.56 g A^?1 h^?1. The LHCE reduces the solubility of lithium polysulfides, allowing the Li/S cell to achieve super performance in a lean electrolyte. This conception of using inert diluents in a highly concentrated electrolyte can accelerate commercialization of Li–S battery technology.     

Designing Safe Electrolyte Systems for a High‐Stability Lithium–Sulfur Battery

Safety, nontoxicity, and durability directly determine the applicability of the essential characteristics of the lithium (Li)‐ion battery. Particularly, for the lithium–sulfur battery, due to the low ignition temperature of sulfur, metal lithium as the anode material, and the use of flammable organic electrolytes, addressing security problems is of increased difficulty. In the past few years, two basic electrolyte systems are studied extensively to solve the notorious safety issues. One system is the conventional organic liquid electrolyte, and the other is the inorganic solid‐state or quasi‐solid‐state composite electrolyte. Here, the recent development of engineered liquid electrolytes and design considerations for solid electrolytes in tackling these safety issues are reviewed to ensure the safety of electrolyte systems between sulfur cathode materials and the lithium‐metal anode. Specifically, strategies for designing and modifying liquid electrolytes including introducing gas evolution, flame, aqueous, and dendrite‐free electrolytes are proposed. Moreover, the considerations involving a high‐performance Li⁺ conductor, air‐stable Li⁺ conductors, and stable interface performance between the sulfur cathode and the lithium anode for developing all‐solid‐state electrolytes are discussed. In the end, an outlook for future directions to offer reliable electrolyte systems is presented for the development of commercially viable lithium–sulfur batteries.     

Regulating the Hidden Solvation‐Ion‐Exchange in Concentrated Electrolytes for Stable and Safe Lithium Metal Batteries

Lithium–sulfur batteries are attractive for automobile and grid applications due to their high theoretical energy density and the abundance of sulfur. Despite the significant progress in cathode development, lithium metal degradation and the polysulfide shuttle remain two critical challenges in the practical application of Li–S batteries. Development of advanced electrolytes has become a promising strategy to simultaneously suppress lithium dendrite formation and prevent polysulfide dissolution. Here, a new class of concentrated siloxane‐based electrolytes, demonstrating significantly improved performance over the widely investigated ether‐based electrolytes are reported in terms of stabilizing the sulfur cathode and Li metal anode as well as minimizing flammability. Through a combination of experimental and computational investigation, it is found that siloxane solvents can effectively regulate a hidden solvation‐ion‐exchange process in the concentrated electrolytes that results from the interactions between cations/anions (e.g., Li⁺, TFSI^?, and S^2?) and solvents. As a result, it could invoke a quasi‐solid‐solid lithiation and enable reversible Li plating/stripping and robust solid‐electrolyte interphase chemistries. The solvation‐ion‐exchange process in the concentrated electrolytes is a key factor in understanding and designing electrolytes for other high‐energy lithium metal batteries.     

All‐Solid‐State Printed Bipolar Li–S Batteries

Despite their potential advantages over currently widespread lithium‐ion batteries, lithium–sulfur (Li–S) batteries are not yet in practical use. Here, for the first time bipolar all‐solid‐state Li–S batteries (ASSLSBs) are demonstrated that exhibit exceptional safety, flexibility, and aesthetics. The bipolar ASSLSBs are fabricated through a solvent‐drying‐free, ultraviolet curing‐assisted stepwise printing process at ambient conditions, without (high‐temperature/high‐pressure) sintering steps that are required for inorganic electrolyte‐based all‐solid‐state batteries. Two thermodynamically immiscible and nonflammable gel electrolytes based on ethyl methyl sulfone (EMS) and tetraethylene glycol dimethyl ether (TEGDME) are used to address longstanding concerns regarding the grain boundary resistance of conventional inorganic solid electrolytes, as well as the polysulfide shuttle effect in Li–S batteries. The EMS gel electrolytes embedded in the sulfur cathodes facilitate sulfur utilization, while the TEGDME gel composite electrolytes serve as polysulfide‐repelling separator membranes. Benefiting from the well‐designed cell components and printing‐driven facile processability, the resulting bipolar ASSLSBs exhibit unforeseen advancements in bipolar cell configuration, safety, foldability, and form factors, which lie far beyond those achievable with conventional Li–S battery technologies.     

Theoretical Investigation of 2D Conductive Microporous Coordination Polymers as Li–S Battery Cathode with Ultrahigh Energy Density

Even though tremendous achievement has been made experimentally in the performance of lithium–sulfur (Li–S) battery, theoretical studies in this area are lagging behind due to the complexity of the Li–S systems and the effects of solvent. For this purpose, a new methodology is developed for investigating the 2D hexaaminobenzene‐based coordination polymers (2D‐HAB‐CPs) as cathode candidate materials for Li–S batteries via density functional theory calculations in combination with an in‐house developed charge polarized solvent model and a genetic algorithm structure global search code. With high ratios of transition metal atoms and two‐coordinated nitrogen atoms, excellent electric conductivity, and structural porosity, the 2D‐HAB‐CP is able to address all of the three main challenges facing Li–S batteries: confining the lithium polysulfides from dissolution, facilitating the electron conductivity and buffering the volumetric expansion during the lithiation process. In addition, the theoretical energy density of this system is as high as 1395 Wh kg^?1. These results demonstrate that the 2D‐HAB‐CP is a promising cathode material for Li–S batteries. The proposed computational framework not only opens a new avenue for understanding the key role played by solution and liquid electrolytes in Li–S batteries, but also can be generally applied to other processes with liquids involved.     

New Lithium Salt Forms Interphases Suppressing Both Li Dendrite and Polysulfide Shuttling

Lithium–sulfur batteries (LSBs) are considered promising candidates for the next‐generation energy‐storage systems due to their high theoretical capacity and prevalent abundance of sulfur. Their reversible operation, however, encounters challenges from both the anode, where dendritic and dead Li‐metal form, and the cathode, where polysulfides dissolve and become parasitic shuttles. Both issues arise from the imperfection of interphases between electrolyte and electrode. Herein, a new lithium salt based on an imide anion with fluorination and unsaturation in its structure is reported, whose interphasial chemistries resolve these issues simultaneously. Lithium 1, 1, 2, 2, 3, 3‐hexafluoropropane‐1, 3‐disulfonimide (LiHFDF) forms highly fluorinated interphases at both anode and cathode surfaces, which effectively suppress formation of Li‐dendrites and dissolution/shuttling of polysulfides, and significantly improves the electrochemical reversibility of LSBs. In a broader context, this new Li salt offers a new perspective for diversified beyond Li‐ion chemistries that rely on a Li‐metal anode and active cathode materials.     

Stabilizing Li–S Battery Through Multilayer Encapsulation of Sulfur

Advancements in portable electronic devices and electric powered transportation has drawn more attention to high energy density batteries, especially lithium–sulfur batteries due to the low cost of sulfur and its high energy density. However, the lithium–sulfur battery is still quite far from commercialization mostly because of incompatibility between all major components of the battery—the cathode, anode, and electrolyte. Here a methodology is demonstrated that shows promise in significantly improving battery stability by multilayer encapsulation of sulfur particles, while using conventional electrolytes, which allows a long cycle life and an improved Coulombic efficiency battery at low electrolyte feeding. The multilayer encapsulated sulfur battery demonstrates a Coulombic efficiency as high as 98%, when a binder‐free electrode is used. It is also shown that the all‐out self‐discharge of the cell after 168 h can be reduced from 34% in the regular sulfur battery to less than 9% in the battery with the multilayer encapsulated sulfur electrode.     

Unraveling the Dual Functionality of High‐Donor‐Number Anion in Lean‐Electrolyte Lithium‐Sulfur Batteries

Minimizing electrolyte use is essential to achieve high practical energy density of lithium–sulfur (Li–S) batteries. However, the sulfur cathode is more readily passivated under a lean electrolyte condition, resulting in low sulfur utilization. In addition, continuous electrolyte decomposition on the Li metal anode aggravates the problem, provoking rapid capacity decay. In this work, the dual functionalities of NO₃^? as a high‐donor‐number (DN) salt anion is presented, which improves the sulfur utilization and cycling stability of lean‐electrolyte Li–S batteries. The NO₃^? anion elevates the solubility of the sulfur species based on its high electron donating ability, achieving a high sulfur utilization of above 1200 mA h g^?1. Furthermore, the anion suppresses electrolyte decomposition on the Li metal by regulating the lithium ion (Li⁺) solvation sheath, enhancing the cycle performance of the lean electrolyte cell. By understanding the anionic effects, this work demonstrates the potential of the high‐DN electrolyte, which is beneficial for both the cathode and anode of Li–S batteries.     

Carbon Quantum Dots–Modified Interfacial Interactions and Ion Conductivity for Enhanced High Current Density Performance in Lithium–Sulfur Batteries

Significant progress has achieved for developing lithium–sulfur (Li–S) batteries with high specific capacities and excellent cyclic stability. However, some critical issues emerge when attempts are made to raise the areal sulfur loading and increase the operation current density to meet the standards for various industrial applications. In this work, polyethylenimine‐functionalized carbon dots (PEI‐CDots) are designed and prepared for enhancing performance of the Li–S batteries with high sulfur loadings and operation under high current density situations. Strong chemical binding effects towards polysulfides and fast ion transport property are achieved in the PEI‐CDots‐modified cathodes. At a high current density of 8 mA cm^?2, the PEI‐CDots‐modified Li–S battery delivers a reversible areal capacity of 3.3 mAh cm^?2 with only 0.07% capacity decay per cycle over 400 cycles at 6.6 mg sulfur loading. Detailed analysis, involving electrochemical impedance spectroscopy, cyclic voltammetry, and density functional theory calculations, is done for the elucidation of the underlying enhancement mechanism by the PEI‐CDots. The strongly localized sulfur species and the promoted Li⁺ ion conductivity at the cathode–electrolyte interface are revealed to enable high‐performance Li–S batteries with high sulfur loading and large operational current.     

Long‐Life,High‐Rate Lithium–Sulfur Cells with a Carbon‐Free VN Host as an Efficient Polysulfide Adsorbent and Lithium Dendrite Inhibitor

Lithium–sulfur (Li‐S) batteries are a promising next‐generation energy‐storage system, but the polysulfide shuttle and dendritic Li growth seriously hinder their commercial viability. Most of the previous studies have focused on only one of these two issues at a time. To address both the issues simultaneously, presented here is a highly conductive, noncarbon, 3D vanadium nitride (VN) nanowire array as an efficient host for both sulfur cathodes and lithium‐metal anodes. With fast electron and ion transport and high porosity and surface area, VN traps the soluble polysulfides, promotes the redox kinetics of sulfur cathodes, facilitates uniform nucleation/growth of lithium metal, and inhibits lithium dendrite growth at an unprecedented high current density of 10 mA cm^?2 over 200 h of repeated plating/stripping. As a result, VN‐Li||VN‐S full cells constructed with VN as both an anode and cathode host with a negative to positive electrode capacity ratio of only ≈2 deliver remarkable electrochemical performance with a high Coulombic efficiency of ≈99.6% over 850 cycles at a high 4 C rate and a high areal capacity of 4.6 mA h cm^?2. The strategy presented here offers a viable approach to realize high‐energy‐density, safe Li‐metal‐based batteries.     

Highly Dispersed Cobalt Clusters in Nitrogen‐Doped Porous Carbon Enable Multiple Effects for High‐Performance Li–S Battery

The lithium–sulfur (Li–S) battery is considered a promising candidate for the next generation of energy storage system due to its high specific energy density and low cost of raw materials. However, the practical application of Li–S batteries is severely limited by several weaknesses such as the shuttle effect of polysulfides and the insulation of the electrochemical products of sulfur and Li₂S/Li₂S₂. Here, by doping nitrogen and integrating highly dispersed cobalt catalysts, a porous carbon nanocage derived from glucose adsorbed metal–organic framework is developed as the host for a sulfur cathode. This host structure combines the reported positive effects, including high conductivity, high sulfur loading, effective stress release, fast lithium‐ion kinetics, fast interface charge transport, fast redox of Li₂S_n, and strong physical/chemical absorption, achieving a long cycle life (86% of capacity retention at 1C within 500 cycles) and high rate performance (600 mAh g^?1 at 5C) for a Li–S battery. By combining experiments and density functional theoretical calculations, it is demonstrated that the well‐dispersed cobalt clusters play an important role in greatly improving the diffusion dynamics of lithium, and enhance the absorption and conversion capability of polysulfides in the host structure.     

Fluorine‐Free Noble Salt Anion for High‐Performance All‐Solid‐State Lithium–Sulfur Batteries

Amongst post‐Li‐ion battery technologies, lithium–sulfur (Li–S) batteries have captured an immense interest as one of the most appealing devices from both the industrial and academia sectors. The replacement of conventional liquid electrolytes with solid polymer electrolytes (SPEs) enables not only a safer use of Li metal (Li°) anodes but also a flexible design in the shape of Li–S batteries. However, the practical implementation of SPEs‐based all‐solid‐state Li–S batteries (ASSLSBs) is largely hindered by the shuttling effect of the polysulfide intermediates and the formation of dendritic Li° during the battery operation. Herein, a fluorine‐free noble salt anion, tricyanomethanide [C(CN)₃^?, TCM^?], is proposed as a Li‐ion conducting salt for ASSLSBs. Compared to the widely used perfluorinated anions {e.g., bis(trifluoromethanesulfonyl)imide anion, [N(SO₂CF₃)₂)]^?, TFSI^?}, the LiTCM‐based electrolytes show decent ionic conductivity, good thermal stability, and sufficient anodic stability suiting the cell chemistry of ASSLSBs. In particular, the fluorine‐free solid electrolyte interphase layer originating from the decomposition of LiTCM exhibits a good mechanical integrity and Li‐ion conductivity, which allows the LiTCM‐based Li–S cells to be cycled with good rate capability and Coulombic efficiency. The LiTCM‐based electrolytes are believed to be the most promising candidates for building cost‐effective and high energy density ASSLSBs in the near future.     

A New Hydrophilic Binder Enabling Strongly Anchoring Polysulfides for High‐Performance Sulfur Electrodes in Lithium‐Sulfur Battery

As one of the important ingredients in lithium‐sulfur battery, the binders greatly impact the battery performance. However, conventional binders have intrinsic drawbacks such as poor capability of absorbing hydrophilic lithium polysulfides, resulting in severe capacity decay. This study reports a new type of binder by polymerization of hydrophilic poly(ethylene glycol) diglycidyl ether with polyethylenimine, which enables strongly anchoring polysulfides for high‐performance lithium sulfur batteries, demonstrating remarkable improvement in both mechanical performance for standing up to 100 g weight and an excellent capacity retention of 72% over 400 cycles at 1.5 C. Importantly, in situ micro‐Raman investigation verifies the effectively reduced polysulfides shuttling from sulfur cathode to lithium anode, which shows the greatly suppressed shuttle effect by the polar‐functional binder. X‐ray photoelectron spectroscopy analysis into the discharge intermediates upon battery cycling reveals that the hydrophilic binder endows the sulfur electrodes with multidimensional Li‐O, Li‐N, and S‐O interactions with sulfur species to effectively mitigate lithium polysulfide dissolution, which is theoretically confirmed by density‐functional theory calculations.     

Boosting Polysulfide Redox Kinetics by Graphene‐Supported Ni Nanoparticles with Carbon Coating

Lithium–sulfur batteries have attracted extensive attention because of their high energy density. However, their application is still impeded by the inherent sluggish kinetics and solubility of intermediate products (i.e., polysulfides) of the sulfur cathode. Herein, graphene‐supported Ni nanoparticles with a carbon coating are fabricated by directly carbonizing a metal–organic framework/graphene oxide composite, which is then dispersed on a commercial glass fiber membrane to form a separator with electrocatalytic activity. In situ analysis and electrochemical investigation demonstrate that this modified separator can effectively suppress the shuttle effect and regulate the catalytic conversion of intercepted polysulfides, which is also confirmed by density functional theory calculations. It is found that Ni–C sites can chemically interact with polysulfides and stabilize the radical S₃^?? through Ni? S bonds to enable fast dynamic equilibrium with S₆^2?, while Ni nanoparticles reduce the oxidation barrier of Li₂S and accelerate ion/electron transport. As a result, the corresponding lithium–sulfur battery shows a high cycle stability (88% capacity retention over 100 cycles) even with a high sulfur mass loading of 8 mg cm^?2 and lean electrolyte (6.25 µ L mg^?1). Surprisingly, benefitting from the improved kinetics, the battery can work well at ?50 °C, which is rarely achieved by conventional Li–S batteries.     

Hybrid and Aqueous Lithium‐Air Batteries

Lithium‐air (Li‐air) batteries have become attractive because of their extremely high theoretical energy density. However, conventional Li‐air cells operating with non‐aqueous electrolytes suffer from poor cycle life and low practical energy density due to the clogging of the porous air cathode by insoluble discharge products, contamination of the organic electrolyte and lithium metal anode by moist air, and decomposition of the electrolyte during cycling. These difficulties may be overcome by adopting a cell configuration that consists of a lithium‐metal anode protected from air by a Li⁺‐ion solid electrolyte and an air electrode in an aqueous catholyte. In this type of configuration, a Li⁺‐ion conducting “buffer” layer between the lithium‐metal anode and the solid electrolyte is often necessary due to the instability of many solid electrolytes in contact with lithium metal. Based on the type of buffer layer, two different battery configurations are possible: “hybrid” Li‐air batteries and “aqueous” Li‐air batteries. The hybrid and aqueous Li‐air batteries utilize the same battery chemistry and face similar challenges that limit the cell performance. Here, an overview of recent developments in hybrid and aqueous Li‐air batteries is provided and the factors that influence their performance and impede their practical applications, followed by future directions are discussed.     

An Efficient Separator with Low Li‐Ion Diffusion Energy Barrier Resolving Feeble Conductivity for Practical Lithium–Sulfur Batteries

Due to unprecedented features including high‐energy density, low cost, and light weight, lithium–sulfur batteries have been proposed as a promising successor of lithium‐ion batteries. However, unresolved detrimental low Li‐ion transport rates in traditional carbon materials lead to large energy barrier in high sulfur loading batteries, which prevents the lithium–sulfur batteries from commercialization. In this report, to overcome the challenge of increasing both the cycling stability and areal capacity, a metallic oxide composite (NiCo₂O₄@rGO) is designed to enable a robust separator with low energy barrier for Li‐ion diffusion and simultaneously provide abundant active sites for the catalytic conversion of the polar polysulfides. With a high sulfur‐loading of 6 mg cm^?2 and low sulfur/electrolyte ratio of 10, the assembled batteries deliver an initial capacity of 5.04 mAh cm^?2 as well as capacity retention of 92% after 400 cycles. The metallic oxide composite NiCo₂O₄@rGO/PP separator with low Li‐ion diffusion energy barrier opens up the opportunity for lithium–sulfur batteries to achieve long‐cycle, cost‐effective operation toward wide applications in electric vehicles and electronic devices.     

Tethered Molecular Sorbents: Enabling Metal‐Sulfur Battery Cathodes

A rechargeable battery that uses sulfur at the cathode and a metal (e.g., Li, Na, Mg, or Al) at the anode provides perhaps the most promising path to a solid‐state, rechargeable electrochemical storage device capable of high charge storage capacity. It is understood that solubilization in the electrolyte and loss of sulfur in the form of long‐chain lithium polysulfides (Li₂S_x, 2 < x < 8) has hindered development of the most studied of these devices, the rechargeable Li‐S battery. Beginning with density‐functional calculations of the structure and interactions of a generic lithium polysulfide species with nitrile containing molecules, it is shown that it is possible to design nitrile‐rich molecular sorbents that anchor to other components in a sulfur cathode and which exert high‐enough binding affinity to Li₂S_x to limit its loss to the electrolyte. It is found that sorbents based on amines and imidazolium chloride present barriers to dissolution of long‐chain Li₂S_x and that introduction of as little as 2 wt% of these molecules to a physical sulfur‐carbon blend leads to Li‐S battery cathodes that exhibit stable long‐term cycling behaviors at high and low charge/discharge rates.     

A Multifunctional Separator Enables Safe and Durable Lithium/Magnesium–Sulfur Batteries under Elevated Temperature

Rechargeable metal–sulfur batteries encounter severe safety hazards and fast capacity decay, caused by the flammable and shrinkable separator and unwanted polysulfide dissolution under elevated temperatures. Herein, a multifunctional Janus separator is designed by integrating temperature endurable electrospinning polyimide nonwovens with a copper nanowire‐graphene nanosheet functional layer and a rigid lithium lanthanum zirconium oxide‐polyethylene oxide matrix. Such architecture offers multifold advantages: i) intrinsically high dimensional stability and flame‐retardant capability, ii) excellent electrolyte wettability and effective metal dendritic growth inhibition, and iii) powerful physical blockage/chemical anchoring capability for the shuttled polysulfides. As a consequence, the as constructed lithium–sulfur battery using a pure sulfur cathode displays an outstandingly high discharge capacity of 1402.1 mAh g^?1 and a record high cycling stability (approximately average 0.24% capacity decay per cycle within 300 cycles) at 80 °C, outperforming the state‐of‐the‐art results in the literature. Promisingly, a high sulfur mass loading of ≈3.0 mg cm^?2 and a record low electrolyte/sulfur ratio of 6.0 are achieved. This functional separator also performs well for a high temperature magnesium–sulfur battery. This work demonstrates a new concept for high performance metal–sulfur battery design and promises safe and durable operation of the next generation energy storage systems.     

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

Lithium‐sulfur (Li–S) batteries are one of the most promising alternative energy storage systems beyond Li‐ion batteries. However, the sluggish kinetics of the nucleation and growth of the solid discharge product of Li₂S/Li₂S₂ in the lower discharge plateau has been recently identified as a critical hurdle for attaining high specific capacity in Li–S batteries with high sulfur loadings under lean electrolyte conditions. Herein, a new strategy of breaking the charge‐transport bottleneck by successful generation of experimentally verified stable Li₂S₂ and a reservoir of quasi‐solid lithium polysulfides within the micropores of activated carbon fiber cloth as a high‐sulfur‐loading host is proposed. The developed Li–S cell is capable of delivering a highly sustainable areal capacity of 6.0 mAh cm^?2 under lower electrolyte to sulfur ratios (<3.0 mL_E g_S^?1). Micropore confinement leads to generation of solid Li₂S₂ that enables high utilization of the entire electroactive area by its inherent self‐healing capacity. This strategy opens a new avenue for rational material designs for Li–S batteries under lean electrolyte condition.