Highly Solvating Electrolytes for Lithium–Sulfur Batteries

There is a critical need to evaluate lithium–sulfur (Li–S) batteries with practically relevant high sulfur loadings and minimal electrolyte. Under such conditions, the concentration of soluble polysulfide intermediates in the electrolyte drastically increases, which can alter the fundamental nature of the solution‐mediated discharge and thereby the total sulfur utilization. In this work, an investigation into various high donor number (DN) electrolytes that allow for increased polysulfide dissolution is presented, and the way in which this property may in fact be necessary for increasing sulfur utilization at low electrolyte and high loading conditions is demonstrated. The solvents dimethylacetamide, dimethyl sulfoxide, and 1‐methylimidazole are holistically evaluated against dimethoxyethane as electrolyte co‐solvents in Li–S cells, and they are used to investigate chemical and electrochemical properties of polysulfide species at both dilute and practically relevant conditions. The nature of speciation exhibited by lithium polysulfides is found to vary significantly between these concentrations, particularly with regard to the S₃^?? species. Furthermore, the extent of the instability in conventional electrolyte solvents and high DN solvents with both lithium metal and polysulfides is thoroughly investigated. These studies establish a basis for future efforts into rationally designing an optimal electrolyte for a lean electrolyte, high energy density Li–S battery.     

Recent Progress in High Donor Electrolytes for Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries continue to be considered promising post‐lithium‐ion batteries owing to their high theoretical energy density. In pursuit of a Li–S cell with long‐term cyclability, most studies thus far have relied on using ether‐based electrolytes. However, their limited ability to dissolve polysulfides requires a high electrolyte‐to‐sulfur ratio, which impairs the achievable specific energy. Recently, the battery community found high donor electrolytes to be a potential solution to this shortcoming because their high solubility toward polysulfides enables a cell to operate under lean electrolyte conditions. Despite the increasing number of promising outcomes with high donor electrolytes, a critical hurdle related to stability of the lithium‐metal counter electrode needs to be overcome. This review provides an overview of recent efforts pertaining to high donor electrolytes in Li–S batteries and is intended to raise interest from within the community. Furthermore, based on analogous efforts in the lithium‐air battery field, strategies for protecting the lithium metal electrode are proposed. It is predicted that high donor electrolytes will be elevated to a higher status in the field of Li–S batteries, with the hope that either existing or upcoming strategies will, to a fair extent, mitigate the degradation of the lithium–metal interface.     

Catalytic Polysulfide Conversion and Physiochemical Confinement for Lithium–Sulfur Batteries

The lithium–sulfur (Li–S) battery is widely regarded as a promising energy storage device due to its low price and the high earth‐abundance of the materials employed. However, the shuttle effect of lithium polysulfides (LiPSs) and sluggish redox conversion result in inefficient sulfur utilization, low power density, and rapid electrode deterioration. Herein, these challenges are addressed with two strategies 1) increasing LiPS conversion kinetics through catalysis, and 2) alleviating the shuttle effect by enhanced trapping and adsorption of LiPSs. These improvements are achieved by constructing double‐shelled hollow nanocages decorated with a cobalt nitride catalyst. The N‐doped hollow inner carbon shell not only serves as a physiochemical absorber for LiPSs, but also improves the electrical conductivity of the electrode; significantly suppressing shuttle effect. Cobalt nitride (Co₄N) nanoparticles, embedded in nitrogen‐doped carbon in the outer shell, catalyze the conversion of LiPSs, leading to decreased polarization and fast kinetics during cycling. Theoretical study of the Li intercalation energetics confirms the improved catalytic activity of the Co₄N compared to metallic Co catalyst. Altogether, the electrode shows large reversible capacity (1242 mAh g^?1 at 0.1 C), robust stability (capacity retention of 658 mAh g^?1 at 5 C after 400 cycles), and superior cycling stability at high sulfur loading (4.5 mg cm^?2).     

Acacia Senegal–Inspired Bifunctional Binder for Longevity of Lithium–Sulfur Batteries

The sulfur cathode in traditional lithium–sulfur batteries suffers from poor cyclability due to polysulfide shuttling effect as well as large volume change during charge/discharge processes. Gum arabic (GA), a low cost, nontoxic, and sustainable natural polymer from Acacia senegal, is adopted as a binder for the sulfur cathode to address these issues. The excellent mechanical properties of GA endow the cathode with high binding strength and suitable ductility to buffer volume change, while the functional groups chemically and physically confine sulfur species within the cathode to inhibit the shuttling effect of polysulfides. Additionally, GA shifts the electrode fabrication process from the organic solvent process to an aqueous process, eliminates the use of toxic organic solvents, and achieves uniformly distributed electrode with lower impedance. A remarkable cycling performance, i.e., 841 mAh g^?1 at low current rate of C/5, is achieved throughout 500 cycles due to the bifunctions of the GA binder.     

An Effective Lithium Sulfide Encapsulation Strategy for Stable Lithium–Sulfur Batteries

With a high theoretical capacity of 1162 mA h g^?1, Li₂S is a promising cathode that can couple with silicon, tin, or graphite anodes for next‐generation energy storage devices. Unfortunately, Li₂S is highly insulating, exhibits large charge overpotential, and suffers from active‐material loss as soluble polysulfides during battery cycling. To date, low‐cost, scalable synthesis of an electrochemically active Li₂S cathode remains a challenge. This work demonstrates that the low conductivity and material loss issues associated with Li₂S cathodes can be overcome by forming a stable, conductive encapsulation layer at the surface of the Li₂S bulk particles through in situ surface reactions between Li₂S and electrolyte additives containing transition‐metal salts. It is identified that the electronic band structure in the valence band region of the thus‐generated encapsulation layers, consisting largely of transition‐metal sulfides, determines the initial charging resistance of Li₂S. Furthermore, among the transition metals tested, the encapsulation layer formed with an addition of 10 wt% manganese (II) acetylacetonate salt proved to be robust within the cycling window, which is attributed to the chemically generated MnS surface species. This work provides an effective strategy to use micrometer‐sized Li₂S directly as a cathode material and opens up new prospects to tune the surface properties of electrode materials for energy‐storage applications.     

Tin Intercalated Ultrathin MoO3 Nanoribbons for Advanced Lithium–Sulfur Batteries

Heteroatom doping strategies have been widely developed to engineer the conductivity and polarity of 2D materials to improve their performance as the host for sulfur cathode in lithium–sulfur batteries. However, further improvement is limited by the inhomogeneity and the small amount of the doping atoms. An intercalation method to improve the conductivity and polarity of 2D‐layered α‐MoO₃ nanoribbons is developed here, thus, resulting in much improved electrochemical performance as sulfur host with better rate and cycle performance. The first principle calculations show that the binding energy of MoO₃ and lithium polysulfides, lithium sulfide and sulfur is significantly improved after Sn intercalation. The Sn_0.063MoO₃‐S cathode delivers an initial specific capacity of 1390.3 mAh g^?1 at 0.1 C with the Coulombic efficiency up to 99.7% and shows 79.6% retention of the initial capacity over 500 cycles at 1 C rate with a capacity decay of 0.04% per cycle. This intercalation method provides a new strategy to engineer the electrochemical properties of 2D materials.     

A Metal Organic Framework Derived Solid Electrolyte for Lithium–Sulfur Batteries

Lithium–sulfur batteries (LSBs) are currently considered as promising candidates for next‐generation energy storage technologies. However, their practical application is hindered by the critical issue of the polysulfide‐shuttle. Herein, a metal organic framework (MOF)‐derived solid electrolyte is presented to address it. The MOF solid electrolyte is developed based on a Universitetet i Oslo (UIO) structure. By grafting a lithium sulfonate (‐SO₃Li) group to the UIO ligand, both the ionic conductivity and the polysulfide‐suppression capability of the resulting ‐SO₃Li grafted UIO (UIOSLi) solid electrolyte are greatly improved. After integrating a Li‐based ionic liquid (Li‐IL), lithium bis(trifluoromethanesulfonyl)imide in 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide, the resulting Li‐IL/UIOSLi solid electrolyte exhibits an ionic conductivity of 3.3 × 10^?4 S cm^?1 at room temperature. Based on its unique structure, the Li‐IL/UIOSLi solid electrolyte effectively restrains the polysulfide shuttle and suppresses lithium dendritic growth. Lithium–sulfur cells with the Li‐IL/UIOSLi solid electrolyte and a Li₂S₆ catholyte show stable cycling performance that preserves 84% of the initial capacity after 250 cycles with a capacity‐fade rate of 0.06% per cycle.     

Design Principles for Optimum Performance of Porous Carbons in Lithium–Sulfur Batteries

A series of experiments is presented that establishes for the first time the role of some of the key design parameters of porous carbons including surface area, pore volume, and pore size on battery performance. A series of hierarchical porous carbons is used as a model system with an open, 3D, interconnected porous framework and highly controlled porosity. Specifically, carbons with surface areas ranging from ≈500–2800 m² g^?1, pore volume from ≈0.6–5 cm³ g^?1, and pore size from micropores (≈1 nm) to large mesopores (≈30 nm) are synthesized and tested. At high sulfur loadings (≈80 wt% S), pore volume is more important than surface area with respect to sulfur utilization. Mesopore size, in the range tested, does not affect the sulfur utilization. No relationship between porosity and long‐term cycle life is observed. All systems fail after 200–300 cycles, which is likely due to the consumption of the LiNO₃ additive over cycling. Moreover, cryo‐scanning transmission electron microscopy imaging of these carbon–sulfur composites combined with X‐ray diffraction (XRD) provides further insights into the effect of initial sulfur distribution on sulfur utilization while also revealing the inadequacy of the indirect characterization techniques alone in reliably predicting distribution of sulfur within porous carbon matrices.     

Highly Stable Lithium–Sulfur Batteries Based on Laponite Nanosheet‐Coated Celgard Separators

Lithium–sulfur (Li–S) batteries are of great interest due to their high theoretical energy density. However, one of the key issues hindering their real world applications is polysulfide shuttle, which results in severe capacity decay and self‐discharge. Here, a laponite nanosheets/carbon black coated Celgard (LNS/CB‐Celgard) separator to inhibit polysulfide shuttle and to enhance the Li⁺ conductivity simultaneously is reported. The polysulfide shuttle is efficiently inhibited through strong interactions between the O active sites of the LNS and polysulfides by forming the Li···O and O? S bonds. Moreover, the separator features high Li⁺ conductivity, fast Li⁺ diffusion, excellent electrolyte wettability, and high thermal stability. Consequently, the Li–S batteries with the LNS/CB‐Celgard separator and the pure S cathode show a high initial reversible capacity of 1387 mA h g^?1 at 0.1 C, high rate performance, superior cycling stability (with a capacity decay rate of 0.06% cycle^?1 at 0.2 C and 0.028% cycle^?1 at 1.0 C over 500 cycles), and ultralow self‐discharge. The separator could also enhance the performance of other batteries such as the LiFePO₄/separator/Li battery. This work sheds a new light on the design and preparation of novel separators for highly stable Li–S batteries via a “green” and cost‐effective approach.     

Enhancing Catalytic Activity of Titanium Oxide in Lithium–Sulfur Batteries by Band Engineering

The altering of electronic states of metal oxides offers a promising opportunity to realize high‐efficiency surface catalysis, which play a key role in regulating polysulfides (PS) redox in lithium–sulfur (Li–S) batteries. However, little effort has been devoted to understanding the relationship between the electronic state of metal oxides and a catalyst's properties in Li–S cells. Herein, defect‐rich heterojunction electrocatalysts composed of ultrathin TiO_2‐x nanosheets and carbon nanotubes (CNTs) for Li–S batteries are reported. Theoretical simulations indicate that oxygen vacancies and heterojunction can enhance electronic conductivity and chemical adsorption. Spectroscopy and electrochemical techniques further indicate that the rich surface vacancies in TiO_2‐x nanosheets result in highly activated trapping sites for LiPS and lower energy barriers for fast Li ion mobility. Meanwhile, the redistribution of electrons at the heterojunction interfaces realizes accelerated surface electron exchange. Coupled with a polyacrylate terpolymer (LA132) binder, the CNT@TiO_2‐x–S electrodes exhibit a long cycle life of more than 300 cycles at 1 C and a high area capacity of 5.4 mAh cm^?2. This work offers a new perspective on understanding catalyst design in energy storage devices through band engineering.     

A Comprehensive Approach toward Stable Lithium–Sulfur Batteries with High Volumetric Energy Density

A comprehensive approach is reported to construct stable and high volumetric energy density lithium–sulfur batteries, by coupling a multifunctional and hierarchically structured sulfur composite with an in‐situ cross‐linked binder. Through a combination of first‐principles calculations and experimental studies, it is demonstrated that a hybrid sulfur host composed by alternately stacking graphene and layered graphitic carbon nitride embraces high electronic conductivity as well as high polysulfide adsorptivity. It is further shown that the cross‐linked elastomeric binder empowers the hierarchical sulfur composites—multi‐microns in size—with the ability to form crack‐free and compact high‐loading electrodes using traditional slurry processing. Using this approach, electrodes with up to 14.9 mg cm^?2 sulfur loading and an extremely low electrolyte/sulfur ratio as low as 3.5: 1 µL mg^?1 are obtained. This study sheds light on the essential role of multifaceted cathode design and further on the challenges facing lithium metal anodes in building high volumetric energy density lithium–sulfur batteries.     

Bioinspired Binders Actively Controlling Ion Migration and Accommodating Volume Change in High Sulfur Loading Lithium–Sulfur Batteries

High‐loading lithium–sulfur batteries have gained considerable fame for possessing high area capacity, but face a stern challenge from capacity fading because of serious issues, including “polysulfides shuttling,” insulating S/Li₂S, large volume changes, and the shedding of S/C particles during drying or the cell encapsulation process. Herein, a bioinspired water‐soluble binder framework is constructed via intermolecular physical cross‐linking of functional side chains hanging on the terpolymer binder. Experimental results and density‐functional theory (DFT) calculations reveal that this network binder featuring superior volume change accommodation can also capture lithium polysulfides (LiPSs) through strong anchoring of O, N⁺ actives to LiPSs by forming Li···O and N⁺···S_x^2? bonds. In addition, the abundant negative charged sulfonate coordination sites and good electrolyte uptake of the designed binder endow the assembled cells with high lithium ion conductivity and fast lithium ion diffusion. Consequently, a remarkable capacity retention of 98% after 350 cycles at 1 C and a high areal capacity of 12.8 mA h cm^?2 with high sulfur loading of 12.0 mg cm^?2 are achieved by applying the environmentally friendly binder.