Cylindrical Direct‐Current Triboelectric Nanogenerator with Constant Output Current

In this article, a cylindrical direct‐current triboelectric nanogenerator (DC‐TENG) that can generate an almost constant current output with a low crest factor by phase coupling is reported for the first time. Here, the influence of phases (P) and groups (G) on the DC‐TENG is investigated. Experiments show that the crest factor of current, significantly decreases as the phases increase, and the output performance significantly increases as the groups increase. One phase triboelectric power‐generating unit of the DC‐TENG with three‐phase and five‐group (3P5G) produces an open‐circuit voltage of 149.5 V, short‐circuit current 7.3 μA, and transferred charge of 56.7 nC at 600 rpm. The DC‐TENG can produce a coupling current of 21.6 μA and the average output power of 2.04 mW after each phase output is rectified and superimposed. Additionally, the crest factor of output current is reduced to 1.08, and the high‐performance characteristics of an almost constant direct‐current is achieved. The research is of considerable significance to the practical applications of TENGs in powering sensors of low consumption.     

Direct‐Current Triboelectric Nanogenerator Realized by Air Breakdown Induced Ionized Air Channel

The air breakdown phenomenon is generally considered as a negative effect in previous research on triboelectric nanogenerators (TENGs), which is always accompanied by air ionization. Here, by utilizing the air breakdown induced ionized air channel, a direct‐current triboelectric nanogenerator (DC‐TENG) is designed for harvesting contact‐separation mechanical energy. During working process, the charges first transfer from bottom to top electrodes through an external circuit in contact state, then flow back via the ionized air channel created by air breakdown in the separation process. So a unidirectional flow of electrical charges can be observed in the external circuit. With repeating contact‐separation cycles, continuous pulsed DC output through the external circuit can be realized. This working mechanism was verified by real‐time electrode potential monitoring, photocurrent signal detection, and controllable discharging observation. The DC‐TENG can be used for directly and continuously charging an energy storage unit and/or driving electronic devices without using a bridge rectifier. Owing to its simplicity in structure, the mechanism is further applied to fabricate the first flexible DC‐TENG. This research provides a significant fundamental study for DC‐TENG technology and may expand its application in flexible electronics and flexible self‐charging power systems.     

Rotating‐Disk‐Based Direct‐Current Triboelectric Nanogenerator

An innovative design is reported of a direct‐current triboelectric nanogenerator (DC‐TENG) based on a rotating disk design for harvesting rotational mechanical energy. The DC‐TENG consists of two disks and two pairs of flexible electric brushes that are made of carbon fiber and contact two electrodes, respectively. During the rotation, two disks have distinct triboelectric polarities for a cyclic in‐plane charge separation between them and an alternating current is generated between the two electrodes. Because of the sliding contact and automatically switch between the electric brushes and the two electrodes, the current is reversed in the second half of the cycle and a direct current is generated. The role that the rotating speed and the segmentation number have is thoroughly investigated and shows that there is direct current enhancement not only at higher speed but also with more segments. The DC‐TENG has been demonstrated as a constant current source for directly and continuously driving electronic devices and/or charging an energy storage unit without a rectifier bridge. This work presents a novel DC‐TENG technology and opens up more potential applications for harvesting rotational mechanical energy and powering electronics.     

Multifunctional Sensor Based on Translational‐Rotary Triboelectric Nanogenerator

Triboelectric nanogenerators with a large number of desirable advantages, such as flexibility, light weight, and easy integration, are unique for sensor design. In this paper, based on the triboelectric nanogenerator (TENG), a cylindrical self‐powered multifunctional sensor (MS) with a translational‐rotary magnetic mechanism is proposed, which has the capacity to detect acceleration, force, and rotational parameters. The MS can transform a translational motion into a swing motion or a multicircle rotational motion of a low damping magnetic cylinder around a friction layer and hence drives the TENG to generate voltages output. For enhancing the output performance of the TENG, an electrode material with small work function, low resistance, and suitable surface topography is the best choice. According to the structure characteristic of the translational‐rotary magnetic mechanism, the MS can easily respond to a weak striking and can be used to measure the rotational parameters without the need of coaxial installation. Based on the MS, some applications are established, for example measuring the punch acceleration of a boxer, the hitting force and swing angle of golf club, which demonstrate the feasibility and efficiency of the MS and exhibit that the MS could find applications in sports.     

Triboelectric Nanogenerator for Sustainable Wastewater Treatment via a Self‐Powered Electrochemical Process

By harvesting the flowing kinetic energy of water using a rotating triboelectric nanogenerator (R‐TENG), this study demonstrates a self‐powered wastewater treatment system that simultaneously removes rhodamine B (RhB) and copper ions through an advanced electrochemical unit. With the electricity generated by R‐TENG, the removal efficiency (RE) of RhB can reach the vicinity of 100% within just 15 min when the initial concentration of RhB is around 100 ppm at optimized conditions. The removal efficiency of copper ions can reach 97.3% after 3 h within an initial concentration of 150 ppm at an optimized condition. Importantly, a better performance and higher treating efficiency are found by using the pulsed output of R‐TENG than those using direct current (DC) supply for pollutant removal when consuming equal amount of energy. The recovered copper layer on the cathode through R‐TENG is much denser, more uniform, and with smaller grain size (d = 20 nm) than those produced by DC process, which also hints at very promising applications of the R‐TENG in electroplating industry. In light of the merits such as easy portability, low cost, and effectiveness, this R‐TENG‐based self‐powered electrochemical system holds great potential in wastewater treatment and electroplating industry.     

Ion‐Enhanced Field Emission Triboelectric Nanogenerator

As interest in triboelectric nanogenerators (TENGs) continues to increase, some studies have reported that certain limitations exist in TENG due to high potential difference, resulting in air breakdown and field emission. In addition, with known limitations such as extremely low voltage at low external resistance, a breakthrough is required to overcome the limitations of TENG. Here, a new TENG mechanism is reported, utilizing ion‐enhanced field emission (IEFE). Using a simple IEFE‐inducing layer, which consists of a charge accumulation layer and a metal‐to‐metal contact point, electrons can flow directly to a counter electrode while generating high‐output power. Under vertical contact–separation input, the generated root mean square (RMS) power of IEFE‐TENG is 635% higher compared to conventional TENG. As the fundamental mechanism of the IEFE‐TENG is based on installing this simple IEFE‐inducing layer, the power output of existing TENGs including sliding mode types can be boosted. This new TENG mechanism can be a new standard for metal–metal contact TENGs to effectively amplify the output power and to overcome potential limitations.     

Rationally Designed Dual‐Mode Triboelectric Nanogenerator for Harvesting Mechanical Energy by Both Electrostatic Induction and Dielectric Breakdown Effects

With the advantages of its light weight, low cost, and high efficiency especially at low operation frequency, the triboelectric nanogenerator (TENG) is considered to be a potential solution for self‐powered sensor networks and large‐scale renewable blue energy. However, the conventional TENG converts mechanical energy into electrical energy only via either electrostatic induction or electrostatic breakdown. Here, a novel dual‐mode TENG is presented, which can simultaneously harvest mechanical energy by electrostatic induction and dielectric breakdown in a single device. Based on the complementary working mechanism, it achieves a great improvement in the output performance with the sum of two TENGs via a single mechanism and reveals the effect of dielectric layer thickness on the triboelectrification, electrostatic induction, and air breakdown. This study establishes a new methodology to optimize TENGs and provides a new tool to investigate the triboelectrification, electrostatic induction and dielectric breakdown simultaneously.     

Capacitor‐Integrated Triboelectric Nanogenerator Based on Metal–Metal Contact for Current Amplification

The electrical power of triboelectric nanogenerators (TENGs) is increased by surface modifications, and they can successfully power portable devices alone. However, modifying the material and its surface may limit the device lifetime, and most of the portable applications demonstrated in previous studies have excessive input conditions. In this study, a capacitor‐integrated TENG (CI‐TENG) that uses the fundamental mechanisms of the Leyden jar is developed. In this device, a long sheet metal (capacitor electrode)–polymer–metal composite (TENG electrode) is rolled inside the casing cylinder, and a capacitor unit is fabricated at the end of the sheet composite. This new operating mechanism of the CI‐TENG is analyzed in terms of the dielectric constant of the capacitor unit and the metal‐to‐metal contact between electrodes. By instantaneous charging and discharging of the capacitor unit inside the CI‐TENG, it can generate a peak open‐circuit voltage of 156 V and a peak closed‐circuit current of 4.3 mA under manual input. It charges a capacitor more than three times faster than a conventional TENG does. Furthermore, the internal impedance of the CI‐TENG is decreased to 200 kΩ without any external circuit.     

Enhancing the Output Performance of Triboelectric Nanogenerator via Grating‐Electrode‐Enabled Surface Plasmon Excitation

The surface charge density and the output impedance of triboelectric nanogenerators (TENGs) are two critical factors for TENGs to speed up their commercialization, so it is important to explore unique methods to reduce the output impedance and increase the surface charge density. Here, an approach is demonstrated to effectively boost the output performance of TENG while reducing the output impedance of TENGs by utilizing grating‐electrode‐enabled surface plasmon excitation. A sustainable and enhanced output performance of about 40 µA (short‐circuit current) and 350 V (peak‐to‐peak voltage at a resistance of 10 MΩ) is produced via grating‐coupled surface plasmon resonance on the TENG with the aluminum grating electrode in the line density of 600 lines mm^?1, and it delivers a peak output power of 3.6 mW under a loading resistance of 1 MΩ, giving over 4.5‐fold enhancement in output power and a 75% reduction in the output impedance. Finally a self‐powered ultrasonic ranging system is utilized to verify the capability of the TENG in powering portable electrics.     

Oblate Spheroidal Triboelectric Nanogenerator for All‐Weather Blue Energy Harvesting

Triboelectric nanogenerators (TENGs) provide one of the most promising techniques for large‐scale blue energy harvesting. However, lack of reasonable designs has largely hindered TENG from harvesting energy from both rough and tranquil seas. In this paper, an oblate spheroidal TENG assembled by two novel TENG parts is elaborately designed for both situations. The TENG in the upper part is based on spring steel plates without other substrate materials, which makes it possible to output considerable power in rough seas and occupy small space. The TENG in the lower part consists of two copper‐coated polymer films and a rolling ball which can capture small wave energy from tranquil seas. The working mechanism and output performance are systematically studied. A maximum open‐circuit voltage of 281 V and a short‐circuit current of 76 µA can be achieved by one upper part, enough to charge a commercial capacitor for potential applications. More important, the proposed oblate spheroidal shell not only guarantees high sensitivity of the TENG in the lower part, but also qualifies the TENG with unique self‐stabilization and low consumables for the next generation of TENGs with new structural design toward all‐weather blue energy harvesting.     

Highly Flexible and Transparent Polyionic‐Skin Triboelectric Nanogenerator for Biomechanical Motion Harvesting

The advances of flexible electronics have raised demand for power sources with adaptability, flexibility, and multifunctionalities. Triboelectric nanogenerators are promising replacements for traditional batteries. Here, a highly soft skin‐like, transparent, and easily adaptable biomechanical energy harvester, based on a hybrid elastomer and with a polyionic hydrogel as the electrification layer and current collector, is developed. By harvesting the energy in human motion, the device generates an open‐circuit voltage of 70 V, a short‐circuit current density of 30.2 mA m^?2, and a maximum power density of 2.79 W m^?2 in a single‐electrode working mode. Further, it is demonstrated that the device can deliver power under bending, curling or by simple tapping when attached to human skin. In addition, the optimal counterpart of the polyionic layer with highest electronegativity difference is selected from a series of contact electrification materials based on a two‐electrode working mode, where a flexible device with the matching counterparts is investigated. Serving as ionic conductor and electrification layer, this polyionic material shows promising application in future development of self‐powered flexible electronics.     

Long‐Lifetime Triboelectric Nanogenerator Operated in Conjunction Modes and Low Crest Factor

The high‐output triboelectric nanogenerator (TENG) is indispensable for its practical applications toward industrial products. However, the electricity loss in simple parallel connection among all units and the typically high crest factor output seriously hamper the practical applications of TENG. Here, a rectified TENG is reported in parallel structure to solve the problem of electricity loss in simple parallel connection. The rotational contact–separation structure with phase difference between rectified TENGs addresses high crest factor output and extends service life of rotational TENG simultaneously. The current crest factor is dramatically decreased to 1.31 in multiple rectifier multiple TENG in parallel (MRM‐TENG), while that of TENG in simple parallel is higher than 6. Meanwhile, the current output can retain up to ≈93% of its initial performance after 7 200 000 rotations under 2.00 r s^?1 of 1000 h. Furthermore, the equivalent current can be in linear growth with low crest factor by making MRM‐TENG in parallel for distributed energy supply without electricity loss. This work may provide a new strategy for TENG in parallel to achieve a low crest factor output and long‐term cycling stability power generation in distributed energy harvesting for large‐scale power application.     

Suppressing Lithium Dendrite Growth via Sinusoidal Ripple Current Produced by Triboelectric Nanogenerators

Lithium metal as an ultimate anode material of future rechargeable batteries may furnish the highest energy density for its pairing cathode, although preventing the growth of lithium dendrites in liquid electrolytes is a major challenge. This work reports that stable lithium metal anodes can be achieved by charging with high‐frequency sinusoidal ripple current generated by rotating triboelectric nanogenerators (R‐TENGs). Compared with constant DC current charging, sinusoidal ripple current charging by R‐TENG improves the uniformity of lithium deposition during cycling test. Consequently, symmetric Li/Li cells exhibit lower overpotential and better cycling stability. In addition, full cells assembled with lithium metal anodes and LiFePO₄ cathodes show considerably improved capacity retention when charged by R‐TENG's sinusoidal ripple current (99.5%) compared to constant current (78.7%) after 200 cycles. The charging strategy device in this work provides a promising direction toward improving the cycle life of Li metal batteries. In addition, the combination of R‐TENGs with Li metal batteries offers an encouraging solution for achieving stable energy supply in self‐powered systems.     

Hourglass Triboelectric Nanogenerator as a “Direct Current” Power Source

Hourglass, or sandglass, is known for centuries to record the passage of time. Here, an hourglass triboelectric nanogenerator (HG‐TENG) is reported as a power source by harnessing the kinetic energy of falling particles. By employing the geometry of an hourglass and replacing the sand with a mixture of polytetrafluoroethylene (PTFE) pellets and Al balls, the HG‐TENG delivers a train of electrical pulses of the same sign without a rectifier bridge. When the volume ratio of the PTFE pellets to the Al balls is 1:1, the HG‐TENG is able to light up 160 commercial light emitting diodes intermittently for 18 s. Furthermore, it is demonstrated that the HG‐TENG can also serve as a self‐powered UV counterfeit detector.     

Boosting the Charge Density of Triboelectric Nanogenerator by Suppressing Air Breakdown and Dielectric Charge Leakage

Charge generation and charge decay are two essential factors that determine the surface charge density of a triboelectric nanogenerator (TENG). However, research mainly focuses on boosting charge generation, and little attention is paid to suppressing charge decay. Here, a strategy of suppressing charge decay, including the air breakdown and dielectric charge leakage, of TENG with high surface charge density (HCD-TENG) is proposed by utilizing a dual dielectric layer. A series of parameters of different dielectric materials are tested with the assistance of a charge excitation TENG (CE-TENG) to reveal the relationships between charge generation, air breakdown, and dielectric charge leakage in the atmospheric environment. Further, the phenomenon of dielectric charge leakage limiting the maximum output of TENG prior to air breakdown is observed for the first time. With the simultaneous suppression of the air breakdown and dielectric charge leakage, the output of TENG is enhanced to 2.2 mC m⁻². This work not only provides new insight into the performance optimization and material selection of TENG, but also provides significant guidance for obtaining high-output TENG in the future.     

Triboelectric Nanogenerator Based on Fully Enclosed Rolling Spherical Structure for Harvesting Low‐Frequency Water Wave Energy

Water waves are increasingly regarded as a promising source for large‐scale energy applications. Triboelectric nanogenerators (TENGs) have been recognized as one of the most promising approaches for harvesting wave energy. This work examines a freestanding, fully enclosed TENG that encloses a rolling ball inside a rocking spherical shell. Through the optimization of materials and structural parameters, a spherical TENG of 6 cm in diameter actuated by water waves can provide a peak current of 1 μA over a wide load range from a short‐circuit condition to 10 GΩ, with an instantaneous output power of up to 10 mW. A multielectrode arrangement is also studied to improve the output of the TENG under random wave motions from all directions. Moreover, at a frequency of 1.43 Hz, the wave‐driven TENG can directly drive tens of LEDs and charge a series of supercapacitors to rated voltage within several hours. The stored energy can power an electronic thermometer for 20 min. This rolling‐structured TENG is extremely lightweight, has a simple structure, and is capable of rocking on or in water to harvest wave energy; it provides an innovative and effective approach toward large‐scale blue energy harvesting of oceans and lakes.     

Honeycomb Structure Inspired Triboelectric Nanogenerator for Highly Effective Vibration Energy Harvesting and Self‐Powered Engine Condition Monitoring

Vibration in mechanical equipment can serve as a sustainable energy source to power sensors and devices if it can be effectively collected. In this work, a honeycomb structure inspired triboelectric nanogenerator (HSI‐TENG) consisting of two copper electrode layers with sponge bases and one honeycomb frame filled with polytetrafluoroethylene (PTFE) balls is proposed to harvest vibration energy. The application of a compact honeycomb structure increases the maximum power density of HSI‐TENG by 43.2% compared to the square grid structure and provides superior advantages in large‐scale manufacturing. More importantly, the nonspring‐assisted HSI‐TENG can generate electricity once the PTFE balls obtain sufficient kinetic energy to separate from the bottom electrode layer regardless of the vibration frequency and direction. This is fundamentally different from the spring‐assisted harvesters that can only work around their natural frequencies. The vibration model and working criteria of the HSI‐TENG are established. Furthermore, the HSI‐TENG is successfully used to serve as a self‐powered sensor to monitor engine conditions by analyzing the electrical output of the HSI‐TENG installed on a diesel engine. Therefore, the nonspring‐assisted HSI‐TENG provides a novel strategy for highly effective vibration energy harvesting and self‐powered machinery monitoring.     

Multiple‐Frequency High‐Output Triboelectric Nanogenerator Based on a Water Balloon for All‐Weather Water Wave Energy Harvesting

Energy and the environment are two of the main issues facing the world today. As a consequence abundant renewable green energy sources such as wave energy, have become hot topics. Here, a multiple‐frequency triboelectric nanogenerator based on the water balloon (WB‐TENG) is proposed for harvesting water wave energy in any direction. Owing to the high elasticity of the water balloon, the WB‐TENG can realize a multiple‐frequency response to low‐frequency external mechanical simulations to generate high‐frequency electrical output. In addition, the water balloon can achieve self‐support without any additional supporting structure because of its tension, to make WB‐TENG still produce electrical output under slight vibration, which can also bring high energy conversion efficiency. Moreover, the fabricated WB‐TENG generates a maximum instantaneous short‐circuit current and an open‐circuit voltage of 147 µA and 1221 V, respectively. Most noteworthy, under the same conditions, the total transferred charge of WB‐TENG is 28 times than that of traditional TENG based on double plate structure during one working cycle. Therefore, this design can provide an effective way to promote the development of TENGs in blue energy.