Pseudo‐Zn–Air and Zn‐Ion Intercalation Dual Mechanisms to Realize High‐Areal Capacitance and Long‐Life Energy Storage in Aqueous Zn Battery

Aqueous zinc batteries are considered as promising alternatives to lithium ion batteries owing to their low cost and high safety. However, the developments of state‐of‐the‐art zinc‐ion batteries (ZIB) and zinc–air batteries (ZAB) are limited by the unsatisfied capacities and poor cycling stabilities, respectively. It is of significance in utilizing the long‐cycle life of ZIB and high capacity of ZAB to exploit advanced energy storage systems. Herein, a bulk composite of graphene oxide and vanadium oxide (V₅O₁₂·6H₂O) as cathode material for aqueous Zn batteries in a mild electrolyte is employed. The battery performance is demonstrated to arise from a combination of the reversible cations insertion/extraction in vanadium oxide and especially the electrochemical redox reactions on the surface functional groups of graphene oxide (named as pseudo‐Zn–air mechanism). Along with adjusting the hydroxyl content on the surface of graphene oxide, the specific capacity is significantly increased from 342 mAh g^?1 to a maximum of 496 mAh g^?1 at 100 mA g^?1. The surface‐controlled kinetics occurring in the bulk composite ensure a high areal capacity of 10.6 mAh cm^?2 at a mass loading of 26.5 mg cm^?2, and a capacity retention of 84.7% over 10 000 cycles at a high current density of 10 A g^?1.     

An Efficient Separator with Low Li‐Ion Diffusion Energy Barrier Resolving Feeble Conductivity for Practical Lithium–Sulfur Batteries

Due to unprecedented features including high‐energy density, low cost, and light weight, lithium–sulfur batteries have been proposed as a promising successor of lithium‐ion batteries. However, unresolved detrimental low Li‐ion transport rates in traditional carbon materials lead to large energy barrier in high sulfur loading batteries, which prevents the lithium–sulfur batteries from commercialization. In this report, to overcome the challenge of increasing both the cycling stability and areal capacity, a metallic oxide composite (NiCo₂O₄@rGO) is designed to enable a robust separator with low energy barrier for Li‐ion diffusion and simultaneously provide abundant active sites for the catalytic conversion of the polar polysulfides. With a high sulfur‐loading of 6 mg cm^?2 and low sulfur/electrolyte ratio of 10, the assembled batteries deliver an initial capacity of 5.04 mAh cm^?2 as well as capacity retention of 92% after 400 cycles. The metallic oxide composite NiCo₂O₄@rGO/PP separator with low Li‐ion diffusion energy barrier opens up the opportunity for lithium–sulfur batteries to achieve long‐cycle, cost‐effective operation toward wide applications in electric vehicles and electronic devices.     

Graphene‐Based Nanocomposites for Energy Storage

Since the first report of using micromechanical cleavage method to produce graphene sheets in 2004, graphene/graphene‐based nanocomposites have attracted wide attention both for fundamental aspects as well as applications in advanced energy storage and conversion systems. In comparison to other materials, graphene‐based nanostructured materials have unique 2D structure, high electronic mobility, exceptional electronic and thermal conductivities, excellent optical transmittance, good mechanical strength, and ultrahigh surface area. Therefore, they are considered as attractive materials for hydrogen (H₂) storage and high‐performance electrochemical energy storage devices, such as supercapacitors, rechargeable lithium (Li)‐ion batteries, Li–sulfur batteries, Li–air batteries, sodium (Na)‐ion batteries, Na–air batteries, zinc (Zn)–air batteries, and vanadium redox flow batteries (VRFB), etc., as they can improve the efficiency, capacity, gravimetric energy/power densities, and cycle life of these energy storage devices. In this article, recent progress reported on the synthesis and fabrication of graphene nanocomposite materials for applications in these aforementioned various energy storage systems is reviewed. Importantly, the prospects and future challenges in both scalable manufacturing and more energy storage‐related applications are discussed.     

Fluorine‐Free Noble Salt Anion for High‐Performance All‐Solid‐State Lithium–Sulfur Batteries

Amongst post‐Li‐ion battery technologies, lithium–sulfur (Li–S) batteries have captured an immense interest as one of the most appealing devices from both the industrial and academia sectors. The replacement of conventional liquid electrolytes with solid polymer electrolytes (SPEs) enables not only a safer use of Li metal (Li°) anodes but also a flexible design in the shape of Li–S batteries. However, the practical implementation of SPEs‐based all‐solid‐state Li–S batteries (ASSLSBs) is largely hindered by the shuttling effect of the polysulfide intermediates and the formation of dendritic Li° during the battery operation. Herein, a fluorine‐free noble salt anion, tricyanomethanide [C(CN)₃^?, TCM^?], is proposed as a Li‐ion conducting salt for ASSLSBs. Compared to the widely used perfluorinated anions {e.g., bis(trifluoromethanesulfonyl)imide anion, [N(SO₂CF₃)₂)]^?, TFSI^?}, the LiTCM‐based electrolytes show decent ionic conductivity, good thermal stability, and sufficient anodic stability suiting the cell chemistry of ASSLSBs. In particular, the fluorine‐free solid electrolyte interphase layer originating from the decomposition of LiTCM exhibits a good mechanical integrity and Li‐ion conductivity, which allows the LiTCM‐based Li–S cells to be cycled with good rate capability and Coulombic efficiency. The LiTCM‐based electrolytes are believed to be the most promising candidates for building cost‐effective and high energy density ASSLSBs in the near future.     

Strategies toward High‐Loading Lithium–Sulfur Battery

Lithium–sulfur (Li–S) batteries, due to the high theoretical energy density, are regarded as one of the most promising candidates for breaking the limitations of energy‐storage system based on Li‐ion batteries. Tremendous efforts have been made to meet the challenge of high‐performance Li–S batteries, in which a sulfur loading of above 5 mg cm^?2 delivers an areal capacity higher than 5 mAh cm^?2 without compromising specific capacity and cycling stability for practical applications. However, serious problems have been exposed during the scaling up of the sulfur loading. In this review, based on mechanistic insights into structural configuration, catalytic conversion, and interfacial engineering, the problems and corresponding strategies in the development of high‐loading Li–S batteries are highlighted and discussed, aiming at bridging the gap between fundamental research and practical cell‐level designs. Stemming from the current achievements, future directions targeting the high‐energy‐density Li–S batteries for commercialization are proposed.     

Enabling High‐Energy Solid‐State Batteries with Stable Anode Interphase by the Use of Columnar Silicon Anodes

All‐solid‐state batteries (ASSBs) with silicon anodes are promising candidates to overcome energy limitations of conventional lithium‐ion batteries. However, silicon undergoes severe volume changes during cycling leading to rapid degradation. In this study, a columnar silicon anode (col‐Si) fabricated by a scalable physical vapor deposition process (PVD) is integrated in all‐solid‐state batteries based on argyrodite‐type electrolyte (Li₆PS₅Cl, 3 mS cm^?1) and Ni‐rich layered oxide cathodes (LiNi_0.9Co_0.05Mn_0.05O₂, NCM) with a high specific capacity (210 mAh g^?1). The column structure exhibits a 1D breathing mechanism similar to lithium, which preserves the interface toward the electrolyte. Stable cycling is demonstrated for more than 100 cycles with a high coulombic efficiency (CE) of 99.7–99.9% in full cells with industrially relevant areal loadings of 3.5 mAh cm^?2, which is the highest value reported so far for ASSB full cells with silicon anodes. Impedance spectroscopy revealed that anode resistance is drastically reduced after first lithiation, which allows high charging currents of 0.9 mA cm^?2 at room temperature without the occurrence of dendrites and short circuits. Finally, in‐operando monitoring of pouch cells gave valuable insights into the breathing behavior of the solid‐state cell.     

Exploiting Synergistic Effect by Integrating Ruthenium–Copper Nanoparticles Highly Co‐Dispersed on Graphene as Efficient Air Cathodes for Li–CO2 Batteries

Li–CO₂ batteries are attractive electrical energy storage devices; however, they still suffer from unsatisfactory electrochemical performance, and the kinetics of CO₂ reduction and evolution reactions must be improved significantly. Herein, a composite of ruthenium–copper nanoparticles highly co‐dispersed on graphene (Ru–Cu–G) as efficient air cathodes for Li–CO₂ batteries is designed. The Li–CO₂ batteries with Ru–Cu–G cathodes exhibit ultra‐low overpotential and can be operated for 100 cycles with a fixed capacity of 1000 mAh g^?1 at 200 and 400 mA g^?1. The synergistic effect between Ru and Cu not only regulates the growth of discharge products, but also promotes CO₂ reduction and evolution reactions by changing the electron cloud density of the surface between Ru and Cu. This work may provide new directions and strategies for developing highly efficient air cathodes for Li–CO₂ batteries, or even practical Li–air batteries.     

Triboelectrification‐Enabled Self‐Charging Lithium‐Ion Batteries

Li‐ion batteries as energy storage devices need to be periodically charged for sustainably powering electronic devices owing to their limited capacities. Here, the feasibility of utilizing Li‐ion batteries as both the energy storage and scavenging units is demonstrated. Flexible Li‐ion batteries fabricated from electrospun LiMn₂O₄ nanowires as cathode and carbon nanowires as anode enable a capacity retention of 90% coulombic efficiency after 50 cycles. Through the coupling between triboelectrification and electrostatic induction, the adjacent electrodes of two Li‐ion batteries can deliver an output peak voltage of about 200 V and an output peak current of about 25 µA under ambient wind‐induced vibrations of a hexafluoropropene–tetrafluoroethylene copolymer film between the two Li‐ion batteries. The self‐charging Li‐ion batteries have been demonstrated to charge themselves up to 3.5 V in about 3 min under wind‐induced mechanical excitations. The advantages of the self‐charging Li‐ion batteries can provide important applications for sustainably powering electronics and self‐powered sensor systems.     

Long‐Life,High‐Rate Lithium–Sulfur Cells with a Carbon‐Free VN Host as an Efficient Polysulfide Adsorbent and Lithium Dendrite Inhibitor

Lithium–sulfur (Li‐S) batteries are a promising next‐generation energy‐storage system, but the polysulfide shuttle and dendritic Li growth seriously hinder their commercial viability. Most of the previous studies have focused on only one of these two issues at a time. To address both the issues simultaneously, presented here is a highly conductive, noncarbon, 3D vanadium nitride (VN) nanowire array as an efficient host for both sulfur cathodes and lithium‐metal anodes. With fast electron and ion transport and high porosity and surface area, VN traps the soluble polysulfides, promotes the redox kinetics of sulfur cathodes, facilitates uniform nucleation/growth of lithium metal, and inhibits lithium dendrite growth at an unprecedented high current density of 10 mA cm^?2 over 200 h of repeated plating/stripping. As a result, VN‐Li||VN‐S full cells constructed with VN as both an anode and cathode host with a negative to positive electrode capacity ratio of only ≈2 deliver remarkable electrochemical performance with a high Coulombic efficiency of ≈99.6% over 850 cycles at a high 4 C rate and a high areal capacity of 4.6 mA h cm^?2. The strategy presented here offers a viable approach to realize high‐energy‐density, safe Li‐metal‐based batteries.     

Nature‐Inspired Tri‐Pathway Design Enabling High‐Performance Flexible Li–O2 Batteries

Trees have an abundant network of channels for the multiphase transport of water, ions, and nutrients. Recent studies have revealed that multiphase transport of ions, oxygen (O₂) gas, and electrons also plays a fundamental role in lithium–oxygen (Li–O₂) batteries. The similarity in transport behavior of both systems is the inspiration for the development of Li–O₂ batteries from natural wood featuring noncompetitive and continuous individual pathways for ions, O₂, and electrons. Using a delignification treatment and a subsequent carbon nanotube/Ru nanoparticle coating process, one is able to convert a rigid and electrically insulating wood membrane into a flexible and electrically conductive material. The resulting cell walls are comprised of cellulose nanofibers with abundant nanopores, which are ideal for Li⁺ ion transport, whereas the unperturbed wood lumina act as a pathway for O₂ gas transport. The noncompetitive triple pathway design endows the wood‐based cathode with a low overpotential of 0.85 V at 100 mA g^?1, a record‐high areal capacity of 67.2 mAh cm^?2, a long cycling life of 220 cycles, and superior electrochemical and mechanical stability. The integration of such excellent electrochemical performance, outstanding mechanical flexibility, and renewable yet cost‐effective starting materials via a nature‐inspired design opens new opportunities for developing portable energy storage devices.     

Hybrid and Aqueous Lithium‐Air Batteries

Lithium‐air (Li‐air) batteries have become attractive because of their extremely high theoretical energy density. However, conventional Li‐air cells operating with non‐aqueous electrolytes suffer from poor cycle life and low practical energy density due to the clogging of the porous air cathode by insoluble discharge products, contamination of the organic electrolyte and lithium metal anode by moist air, and decomposition of the electrolyte during cycling. These difficulties may be overcome by adopting a cell configuration that consists of a lithium‐metal anode protected from air by a Li⁺‐ion solid electrolyte and an air electrode in an aqueous catholyte. In this type of configuration, a Li⁺‐ion conducting “buffer” layer between the lithium‐metal anode and the solid electrolyte is often necessary due to the instability of many solid electrolytes in contact with lithium metal. Based on the type of buffer layer, two different battery configurations are possible: “hybrid” Li‐air batteries and “aqueous” Li‐air batteries. The hybrid and aqueous Li‐air batteries utilize the same battery chemistry and face similar challenges that limit the cell performance. Here, an overview of recent developments in hybrid and aqueous Li‐air batteries is provided and the factors that influence their performance and impede their practical applications, followed by future directions are discussed.     

Unraveling the Dual Functionality of High‐Donor‐Number Anion in Lean‐Electrolyte Lithium‐Sulfur Batteries

Minimizing electrolyte use is essential to achieve high practical energy density of lithium–sulfur (Li–S) batteries. However, the sulfur cathode is more readily passivated under a lean electrolyte condition, resulting in low sulfur utilization. In addition, continuous electrolyte decomposition on the Li metal anode aggravates the problem, provoking rapid capacity decay. In this work, the dual functionalities of NO₃^? as a high‐donor‐number (DN) salt anion is presented, which improves the sulfur utilization and cycling stability of lean‐electrolyte Li–S batteries. The NO₃^? anion elevates the solubility of the sulfur species based on its high electron donating ability, achieving a high sulfur utilization of above 1200 mA h g^?1. Furthermore, the anion suppresses electrolyte decomposition on the Li metal by regulating the lithium ion (Li⁺) solvation sheath, enhancing the cycle performance of the lean electrolyte cell. By understanding the anionic effects, this work demonstrates the potential of the high‐DN electrolyte, which is beneficial for both the cathode and anode of Li–S batteries.     

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

Lithium‐sulfur (Li–S) batteries are one of the most promising alternative energy storage systems beyond Li‐ion batteries. However, the sluggish kinetics of the nucleation and growth of the solid discharge product of Li₂S/Li₂S₂ in the lower discharge plateau has been recently identified as a critical hurdle for attaining high specific capacity in Li–S batteries with high sulfur loadings under lean electrolyte conditions. Herein, a new strategy of breaking the charge‐transport bottleneck by successful generation of experimentally verified stable Li₂S₂ and a reservoir of quasi‐solid lithium polysulfides within the micropores of activated carbon fiber cloth as a high‐sulfur‐loading host is proposed. The developed Li–S cell is capable of delivering a highly sustainable areal capacity of 6.0 mAh cm^?2 under lower electrolyte to sulfur ratios (<3.0 mL_E g_S^?1). Micropore confinement leads to generation of solid Li₂S₂ that enables high utilization of the entire electroactive area by its inherent self‐healing capacity. This strategy opens a new avenue for rational material designs for Li–S batteries under lean electrolyte condition.     

Interface‐Engineered All‐Solid‐State Li‐Ion Batteries Based on Garnet‐Type Fast Li+ Conductors

All‐solid‐state Li‐ion batteries based on Li₇La₃Zr₂O₁₂ (LLZO) garnet structures require novel electrode assembly strategies to guarantee a proper Li⁺ transfer at the electrode–electrolyte interfaces. Here, first stable cell performances are reported for Li‐garnet, c‐Li_6.25Al_0.25La₃Zr₂O₁₂, all‐solid‐state batteries running safely with a full ceramics setup, exemplified with the anode material Li₄Ti₅O₁₂. Novel strategies to design an enhanced Li⁺ transfer at the electrode–electrolyte interface using an interface‐engineered all‐solid‐state battery cell based on a porous garnet electrolyte interface structure, in which the electrode material is intimately embedded, are presented. The results presented here show for the first time that all‐solid‐state Li‐ion batteries with LLZO electrolytes can be reversibly charge–discharge cycled also in the low potential ranges (≈1.5 V) for combinations with a ceramic anode material. Through a model experiment, the interface between the electrode and electrolyte constituents is systematically modified revealing that the interface engineering helps to improve delivered capacities and cycling properties of the all‐solid‐state Li‐ion batteries based on garnet‐type cubic LLZO structures.     

Efficient Li‐Ion‐Conductive Layer for the Realization of Highly Stable High‐Voltage and High‐Capacity Lithium Metal Batteries

Recently, a consensus has been reached that using lithium metal as an anode in rechargeable Li‐ion batteries is the best way to obtain the high energy density necessary to power electronic devices. Challenges remain, however, with respect to controlling dendritic Li growth on these electrodes, enhancing compatibility with carbonate‐based electrolytes, and forming a stable solid–electrolyte interface layer. Herein, a groundbreaking solution to these challenges consisting in the preparation of a Li₂TiO₃ (LT) layer that can be used to cover Li electrodes via a simple and scalable fabrication method, is suggested. Not only does this LT layer impede direct contact between electrode and electrolyte, thus avoiding side reactions, but it assists and expedites Li‐ion flux in batteries, thus suppressing Li dendrite growth. Other effects of the LT layer on electrochemical performance are investigated by scanning electron microscopy, electrochemical impedance spectroscopy, and galvanostatic intermittent titration technique analyses. Notably, LT layer‐incorporating Li cells comprising high‐capacity/voltage cathodes with reasonably high mass loading (LiNi_0.8Co_0.1Mn_0.1O₂, LiNi_0.5Mn_1.5O₄, and LiMn₂O₄) show highly stable cycling performance in a carbonate‐based electrolyte. Therefore, it is believed that the approach based on the LT layer can boost the realization of high energy density lithium metal batteries and next‐generation batteries.     

Lithiophilic CuO Nanoflowers on Ti‐Mesh Inducing Lithium Lateral Plating Enabling Stable Lithium‐Metal Anodes with Ultrahigh Rates and Ultralong Cycle Life

Lithium (Li) metal anodes are promising candidates for high‐energy‐density batteries. However, uncontrollable dendritic plating behavior and infinite volume expansion are hindering their practical applications. Herein, a novel CuO@Ti‐mesh (CTM) is prepared by microwave‐assisted reactions, followed by pressing on Li wafers, leading to Li/CuO@Ti‐mesh (LCTM) composite anodes. The lithiophilic CuO nanoflowers on Ti‐mesh provides evenly distributed nucleation sites, inducing uniform Li‐ion lateral plating, which can effectively inhibit the growth of Li dendrites and volume expansion during cycling. The as‐prepared LCTM composite anode exhibits high Coulombic efficiency (CE) of 94.2% at 10 mA cm^‐2 over 90 cycles. Meanwhile, the LCTM anode shows a low overpotential of 50 mV at 10 mA cm^‐2 over 16 000 cycles and a low overpotential of 90 and 250 mV even at ultrahigh current densities of 20 and 40 mA cm^‐2. When paired with Li₄Ti₅O₁₂ (LTO), it enhances the capacity retention of LTO/Li wafer full cells by about two times from 36.6% to 73.0% and 42.0% to 80.0% at 5C and 10C with long‐term cycling. It is hoped that this LCTM anode with ultrahigh rates and ultralong cycle life may put Li‐metal anode forward to practical applications, such as in Li–S, Li‐air batteries, etc.     

Enhanced Cyclability of Lithium–Oxygen Batteries with Electrodes Protected by Surface Films Induced via In Situ Electrochemical Process

Although the rechargeable lithium–oxygen (Li–O₂) batteries have extremely high theoretical specific energy, the practical application of these batteries is still limited by the instability of their carbon‐based air‐electrode, Li metal anode, and electrodes, toward reduced oxygen species. Here a simple one‐step in situ electrochemical precharging strategy is demonstrated to generate thin protective films on both carbon nanotubes (CNTs), air‐electrodes and Li metal anodes simultaneously under an inert atmosphere. Li–O₂ cells after such pretreatment demonstrate significantly extended cycle life of 110 and 180 cycles under the capacity‐limited protocol of 1000 mA h g^?1 and 500 mA h g^?1, respectively, which is far more than those without pretreatment. The thin‐films formed from decomposition of electrolyte during in situ electrochemical precharging processes in an inert environment, can protect both CNTs air‐electrode and Li metal anode prior to conventional Li–O₂ discharge/charge cycling, where reactive reduced oxygen species are formed. This work provides a new approach for protection of carbon‐based air‐electrodes and Li metal anodes in practical Li–O₂ batteries, and may also be applied to other battery systems.     

A Flexible Solid‐State Aqueous Zinc Hybrid Battery with Flat and High‐Voltage Discharge Plateau

The migration of zinc‐ion batteries from alkaline electrolyte to neutral or mild acidic electrolyte promotes research into their flexible applications. However, discharge voltage of many reported zinc‐ion batteries is far from satisfactory. On one hand, the battery voltage is substantially restricted by the narrow voltage window of aqueous electrolytes. On the other hand, many batteries yield a low‐voltage discharge plateau or show no plateau but capacitor‐like sloping discharge profiles. This impacts the battery's practicability for flexible electronics where stable and consistent high energy is needed. Herein, an aqueous zinc hybrid battery based on a highly concentrated dual‐ion electrolyte and a hierarchically structured lithium‐ion‐intercalative LiVPO₄F cathode is developed. This hybrid battery delivers a flat and high‐voltage discharge plateau of nearly 1.9 V, ranking among the highest reported values for all aqueous zinc‐based batteries. The resultant high energy density of 235.6 Wh kg^?1 at a power density of 320.8 W kg^?1 also outperforms most reported zinc‐based batteries. A designed solid‐state and long‐lasting hydrogel electrolyte is subsequently applied in the fabrication of a flexible battery, which can be integrated into various flexible devices as powerful energy supply. The idea of designing such a hybrid battery offers a new strategy for developing high‐voltage and high‐energy aqueous energy storage systems.     

Germanium Thin Film Protected Lithium Aluminum Germanium Phosphate for Solid‐State Li Batteries

Solid‐state Li batteries using Na⁺ superionic conductor type solid electrolyte attracts wide interest because of its safety and high theoretical energy density. The NASCION type solid electrolyte LAGP (Li_1.5Al_0.5Ge_0.5P₃O₁₂) shows favorable conductivity as well as good mechanical strength to prevent Li dendrite penetration. However, the instability of LAGP with Li metal remains a great challenge. In this work, an amorphous Ge thin film is sputtered on an LAGP surface, which can not only suppress the reduction reaction of Ge⁴⁺ and Li, but also produces intimate contact between the Li metal and the LAGP solid electrolyte. The symmetric cell with the Ge‐coated LAGP solid electrolyte shows superior stability and cycle performance for 100 cycles at 0.1 mA cm^?2. A quasi‐solid‐state Li–air battery has also been assembled to further demonstrate this advantage. A stable cycling performance of 30 cycles in ambient air can be obtained. This work helps to achieve a stable and ionic conducting interface in solid‐state Li batteries.     

Fast‐Charging and Ultrahigh‐Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm^?2) and small areal capacity (<5 mAh cm^?2), which essentially limits their high‐power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low‐cost Si wafers are used and are chemically etched down to 20–30 µm membranes. Simply laminating a Si membrane onto Li foil results in the formation of Li_xSi alloy film fused onto Li metal with mechanical robustness and high Li‐ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm^?2 and unprecedented areal capacity up to 100 mAh cm^?2. Furthermore, the surface alloyed Li anode is paired with amorphous MoS₃ cathode and achieves remarkable full‐cell performance.