Enhancing the Photovoltaic Performance via Vertical Phase Distribution Optimization in Small Molecule:PC71BM Blends

Bulk heterojunction (BHJ) morphologies are vital to the device performance of organic solar cells (OSCs), including phase separation in lateral and vertical directions. However, the morphology developed from the blend solution is not easily predicted and controlled, especially in the vertical direction, because the BHJ morphology is kinetically frozen during the rapid solvent evaporation process. Here, a simple approach to control BHJ morphologies with optimized phase distribution for small molecule:[6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁ BM) blends by enhancing the substrate temperature during the spin‐coating process. Three molecules with various fluorine atoms in the end acceptor units are selected. The relationship among molecular structures, substrate temperature effects on the morphology, and device performances are symmetrically investigated. Low temperature induces a multiple‐sublayer‐like architecture with significantly varied distributions of composition, morphology, and localized state energy, while high processing temperature induces more uniform film. The short‐circuit current, open‐circuit voltage, and fill factor of the devices are tuned with synergic improvement of efficiency toward over 10% and 11% for conventional and inverted devices. This work reveals the origination of vertical phase segregation, and provides a facile strategy to optimize the hierarchical phase separation for enhancing the performance of OSCs.     

High Performance Thick‐Film Nonfullerene Organic Solar Cells with Efficiency over 10% and Active Layer Thickness of 600 nm

Developing efficient organic solar cells (OSCs) with relatively thick active layer compatible with the roll to roll large area printing process is an inevitable requirement for the commercialization of this field. However, typical laboratory OSCs generally exhibit active layers with optimized thickness around 100 nm and very low thickness tolerance, which cannot be suitable for roll to roll process. In this work, high performance of thick‐film organic solar cells employing a nonfullerene acceptor F–2Cl and a polymer donor PM6 is demonstrated. High power conversion efficiencies (PCEs) of 13.80% in the inverted structure device and 12.83% in the conventional structure device are achieved under optimized conditions. PCE of 9.03% is obtained for the inverted device with active layer thickness of 500 nm. It is worth noting that the conventional structure device still maintains the PCE of over 10% when the film thickness of the active layer is 600 nm, which is the highest value for the NF‐OSCs with such a large active layer thickness. It is found that the performance difference between the thick active layer films based conventional and inverted devices is attributed to their different vertical phase separation in the active layers.     

Controllable ZnMgO Electron‐Transporting Layers for Long‐Term Stable Organic Solar Cells with 8.06% Efficiency after One‐Year Storage

Currently, one main challenge in organic solar cells (OSCs) is to achieve both good stability and high power conversion efficiencies (PCEs). Here, highly efficient and long‐term stable inverted OSCs are fabricated by combining controllable ZnMgO (ZMO) cathode interfacial materials with a polymer:fullerene bulk‐heterojunction. The resulting devices based on the nanocolloid/nanoridge ZMO electron‐transporting layers (ETLs) show greatly enhanced performance compared to that of the conventional devices or control devices without ZMO or with ZnO ETLs. The ZMO‐based OSCs maintain 84%–93% of their original PCEs over 1‐year storage under ambient conditions. An initial PCE of 9.39% is achieved for the best device, and it still retains a high PCE of 8.06% after 1‐year storage, which represents a record high value for long‐term stable OSCs. The excellent performance is attributed to the enhanced electron transportation/collection, reduced interfacial energy losses, and improved stability of the nanocolloid ZMO ETL. These findings provide a promising way to develop OSCs with high efficiencies and long device lifetime towards practical applications.     

Overcoming Space‐Charge Effect for Efficient Thick‐Film Non‐Fullerene Organic Solar Cells

Organic solar cells (OSCs) containing non‐fullerene acceptors have realized high power conversion efficiency (PCE) up to 14%. However, most of these high‐performance non‐fullerene OSCs have been reported with optimal active layer thickness of about 100 nm, mainly due to the low electron mobility (≈10^?4–10^?5 cm² V^?1 s^?1) of non‐fullerene acceptors, which are not suitable for roll‐to‐roll large‐scale processing. In this work, an efficient non‐fullerene OSC based on poly[(5,6‐difluoro‐2,1,3‐benzothiadiazol‐4,7‐diyl)‐alt‐(3,3′″‐di(2‐octyldodecyl)‐2,2′;5′,2″;5″,2′″‐quaterthiophen‐5,5′′′‐diyl)] (PffBT4T‐2OD):EH‐IDTBR (consists of electron‐rich indaceno[1,2‐b:5,6‐b′]dithiophene as the central unit and an electron‐deficient 5,6‐benzo[c][1,2,5]thiadiazole unit flanked with rhodanine as the peripheral group) with thickness‐independent PCE (maintaining a PCE of 9.1% with an active layer thickness of 300 nm) is presented by optimizing device architectures to overcome the space‐charge effects. Optical modeling reveals that most of the incident light is absorbed near the transparent electrode side in thick‐film devices. The transport distance of electrons with lower mobility will therefore be shortened when using inverted device architecture, in which most of the excitons are generated close to the cathode side and therefore substantially reduces the accumulation of electrons in the device. As a result, an efficient thick‐film non‐fullerene OSC is realized. These results provide important guidelines for the development of more efficient thick‐film non‐fullerene OSCs.     

Sequentially Deposited versus Conventional Nonfullerene Organic Solar Cells: Interfacial Trap States,Vertical Stratification,and Exciton Dissociation

Bulk heterojunction (BHJ) nonfullerene organic solar cells prepared from sequentially deposited donor and acceptor layers (sq‐BHJ) have recently been shown to be highly efficient, environmentally friendly, and compatible with large area and roll‐to‐roll fabrication. However, the related photophysics at donor‐acceptor interface and the vertical heterogeneity of donor‐acceptor distribution, critical for exciton dissociation and device performance, have been largely unexplored. Herein, steady‐state and time‐resolved optical and electrical techniques are employed to characterize the interfacial trap states. Correlating with the luminescent efficiency of interfacial states and its nonradiative recombination, interfacial trap states are characterized to be about 40% more populated in the sq‐BHJ devices than the as‐cast BHJ (c‐BHJ), which probably limits the device voltage output. Cross‐sectional energy‐dispersive X‐ray spectroscopy and ultraviolet photoemission spectroscopy depth profiling directly visualize the donor–acceptor vertical stratification with a precision of 1–2 nm. From the proposed “needle” model, the high exciton dissociation efficiency is rationalized. This study highlights the promise of sequential deposition to fabricate efficient solar cells, and points toward improving the voltage output and overall device performance via eliminating interfacial trap states.     

Highly Efficient Tandem Organic Solar Cell Enabled by Environmentally Friendly Solvent Processed Polymeric Interconnecting Layer

In the field of organic solar cells (OSCs), tandem structure devices exhibit very attractive advantages for improving power conversion efficiency (PCE). In addition to the well researched novel pair of active layers in different subcells, the construction of interconnecting layer (ICL) also plays a critical role in achieving high performance tandem devices. In this work, a new way of achieving environmentally friendly solvent processed polymeric ICL by adopting poly[(9,9‐bis(3′‐(N,N‐dimethylamino)propyl)‐2,7‐fluorene)‐alt‐5,5′‐bis(2,2′‐thiophene)‐2,6‐naphthalene‐1,4,5,8‐tetracaboxylic‐N,N′‐di(2‐ethylhexyl)imide] (PNDIT‐F3N) blended with poly(ethyleneimine) (PEI) as the electron transport layer (ETL) and PEDOT:PSS as the hole transport layer is reported. It is found that the modification ability of PNDIT‐F3N on PEDOT can be linearly tuned by the incorporation of PEI, which offers the opportunity to study the charge recombination behavior in ICL. At last, tandem OSC with highest PCE of 12.6% is achieved, which is one of the best tandem OSCs reported till now. These results offer a new selection for constructing efficient ICL in high performance tandem OSCs and guide the way of design new ETL materials for ICL construction, and may even be integrated in future printed flexible large area module device fabrication with the advantages of environmentally friendly solvent processing and thickness insensitivity.     

High-Reproducibility Layer-by-Layer Non-Fullerene Organic Photovoltaics with 19.18% Efficiency Enabled by Vacuum-Assisted Molecular Drift Treatment

The thin film deposition engineering of layer-by-layer (LbL) non-fullerene organic solar cells (OSCs) favors vertical phase distributions of donor:acceptor (D:A), effectively boosting the power conversion efficiency (PCE). However, previous deposition strategies mainly aimed at optimizing the morphology of LbL films, and paid limited attention to the reproducibility of device performance. To achieve high device performance and maintain reproducibility, a strategy for hierarchical morphology manipulation in LbL OSCs is developed. A series of LbL devices are fabricated by introducing vacuum-assisted molecular drift treatment (VMDT) to the donor or acceptor layer individually or simultaneously to elucidate the functionalities of this treatment. Essentially, the VMDT provides an extended drift driving force to manipulate the donor and acceptor molecules, resulting in a well-defined vertical phase distribution and ordered molecular packing. These enhancements facilitate improvement in the D:A interface area and charge transport channel, ultimately contributing to impressive PCEs of 19.18% from 18.27% in the LbL devices. More importantly, using VMDT overcomes the notorious batch-dependent and heat treatment degradation issues of OSCs, leading to excellent batch-to-batch reproducibility and enhanced stability of the devices. This reported method provides a promising strategy available for industrial and laboratory use to controllably manipulate the morphology of LbL OSCs.     

Additive‐Free Organic Solar Cells with Power Conversion Efficiency over 10%

Nowadays, solvent additives are widely used in organic solar cells (OSCs) to tune the nano‐morphology of the active blend film and enhance the device performance. With their help, power conversion efficiencies (PCEs) of OSCs have recently stepped over 10%. However, residual additive in the device can induce undesirable morphological change and also accelerate photo‐oxidation degradation of the active blend film. Thereby, their involvements are actually unfavorable for practical applications. Here, a donor material PThBDTP is employed, and PThBDTP:PC71BM based OSCs are fabricated. A PCE of over 10% is achieved without using any additives and film post‐treatments. The device displays a high open‐circuit voltage of 0.977 V, a large short‐circuit current density of 13.49 mA cm^‐2, and a high fill factor of 76.3%. These results represent an important step towards developing high‐efficiency additive‐free OSCs.     

Efficient Hybrid Tandem Solar Cells Based on Optical Reinforcement of Colloidal Quantum Dots with Organic Bulk Heterojunctions

While colloidal quantum dot photovoltaic devices (CQDPVs) can achieve a power conversion efficiency (PCE) of ≈12%, their insufficient optical absorption in the near‐infrared (NIR) regime impairs efficient utilization of the full spectrum of visible light. Here, high‐efficiency, solution‐processed, hybrid series, tandem photovoltaic devices are developed featuring CQDs and organic bulk heterojunction (BHJ) photoactive materials for front‐ and back‐cells, respectively. The organic BHJ back‐cell efficiently harvests the transmitted NIR photons from the CQD front‐cell, which reinforces the photon‐to‐current conversion at 350–1000 nm wavelengths. Optimizing the short‐circuit current density balance of each sub‐cell and creating a near ideal series connection using an intermediate layer achieve a PCE (12.82%) that is superior to that of each single‐junction device (11.17% and 11.02% for the CQD and organic BHJ device, respectively). Notably, the PCE of the hybrid tandem device is the highest among the reported CQDPVs, including single‐junction devices and tandem devices. The hybrid tandem device also exhibits almost negligible degradation after air storage for 3 months. This study suggests a potential route to improve the performance of CQDPVs by proper hybridization with NIR‐absorbing photoactive materials.     

Evidencing Excellent Thermal‐ and Photostability for Single‐Component Organic Solar Cells with Inherently Built‐In Microstructure

Solution‐processed organic solar cells (OSCs) are promising low‐cost, flexible, portable renewable sources for future energy supply. The state‐of‐the‐art OSCs are typically fabricated from a bulk‐heterojunction (BHJ) active layer containing well‐mixed donor and acceptor molecules in the nanometer regime. However, BHJ solar cells suffer from stability problems caused by the severe morphological changes upon thermal or illumination stress. In comparison, single‐component organic solar cells (SCOSCs) based on a double‐cable conjugated polymer with a covalently stabilized microstructure is suggested to be a key strategy for superior long‐term stability. Here, the thermal‐ and photostability of SCOSCs based on a model double‐cable polymer is systematically investigated. It is encouraging to find that under 90 °C & 1 sun illumination, the performance of SCOSCs remains substantially stable. Transport measurements show that charge generation and recombination (lifetime and recombination order) hardly change during the aging process. Particularly, the SCOSCs exhibit ultrahigh long‐term thermal stability with 100% PCE remaining after heating at temperature up to 160 °C for over 400 h, indicating an excellent candidate for extremely rugged applications.     

Nanofiber‐Based Bulk‐Heterojunction Organic Solar Cells Using Coaxial Electrospinning

Nanofibers consisting of the bulk heterojunction organic photovoltaic (BHJ–OPV) electron donor–electron acceptor pair poly(3‐hexylthiophene):phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) are produced through a coaxial electrospinning process. While P3HT:PCBM blends are not directly electrospinnable, P3HT:PCBM‐containing fibers are produced in a coaxial fashion by utilizing polycaprolactone (PCL) as an electrospinnable sheath material. Pure P3HT:PCBM fibers are easily obtained after electrospinning by selectively removing the PCL sheath with cyclopentanone (average diameter 120 ± 30 nm). These fibers are then incorporated into the active layer of a BHJ–OPV device, which results in improved short‐circuit current densities, fill factors, and power‐conversion efficiencies (PCE) as compared to thin‐film devices of identical chemical composition. The best‐performing fiber‐based devices exhibit a PCE of 4.0%, while the best thin‐film devices have a PCE of 3.2%. This increase in device performance is attributed to the increased in‐plane alignment of P3HT polymer chains on the nanoscale, caused by the electrospun fibers, which leads to increased optical absorption and subsequent exciton generation. This methodology for improving device performance of BHJ–OPVs could also be implemented for other electron donor–electron acceptor systems, as nanofiber formation is largely independent of the PV material.     

Significant Effect of Fluorination on Simultaneously Improving Work Function and Transparency of Anode Interlayer for Organic Solar Cells

Since the highest occupied molecular orbital (HOMO) level of donors in organic solar cells (OSCs) is being constantly downshifted for achieving high open‐circuit voltage (V_oc), a further enhancement of the anode work function (WF) is required. Herein, an effective approach of fluorination is demonstrated to simultaneously improve the WF and transparency for anode interlayer (AIL) material. By fluorination, in combination with the dialysis treatment in LiCl solution, the WF of PCP‐2F‐Li could be significantly enhanced from 4.86 to 5.0 eV, as compared to PCP‐Na. Meanwhile, the transparency of the polymer is also improved. As a result, PCP‐2F‐Li can be used to modify efficient active layers consisting of polymer donors with deep HOMO levels, such as PBDB‐T‐2F:IT‐4F, and an outstanding power conversion efficiency (PCE) of 12.7% is achieved in the corresponding device with a high V_oc of 0.84 V. This result represents the highest efficiency for the OSCs using a solution‐processed pH‐neutral AIL, which is beneficial to the low‐cost fabrication of high‐performance OSCs with improved stability. More importantly, PCP‐2F‐Li could be processed by blade coating for making large‐area device of 1 cm², and a PCE of 10.6% is achieved, bringing a promising prospect for the large‐area device fabrication.     

Printed Nonfullerene Organic Solar Cells with the Highest Efficiency of 9.5%

The current work reports a high power conversion efficiency (PCE) of 9.54% achieved with nonfullerene organic solar cells (OSCs) based on PTB7‐Th donor and 3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene) (ITIC) acceptor fabricated by doctor‐blade printing, which has the highest efficiency ever reported in printed nonfullerene OSCs. Furthermore, a high PCE of 7.6% is realized in flexible large‐area (2.03 cm²) indium tin oxide (ITO)‐free doctor‐bladed nonfullerene OSCs, which is higher than that (5.86%) of the spin‐coated counterpart. To understand the mechanism of the performance enhancement with doctor‐blade printing, the morphology, crystallinity, charge recombination, and transport of the active layers are investigated. These results suggest that the good performance of the doctor‐blade OSCs is attributed to a favorable nanoscale phase separation by incorporating 0.6 vol% of 1,8‐diiodooctane that prolongs the dynamic drying time of the doctor‐bladed active layer and contributes to the migration of ITIC molecules in the drying process. High PCE obtained in the flexible large‐area ITO‐free doctor‐bladed nonfullerene OSCs indicates the feasibility of doctor‐blade printing in large‐scale fullerene‐free OSC manufacturing. For the first time, the open‐circuit voltage is increased by 0.1 V when 1 vol% solvent additive is added, due to the vertical segregation of ITIC molecules during solvent evaporation.     

Porphyrin‐Based Bulk Heterojunction Organic Photovoltaics: The Rise of the Colors of Life

Organic photovoltaics (OPV) represent a thin‐film PV technology that offers attractive prospects for low‐cost and aesthetically appealing (colored, flexible, uniform, semitransparent) solar cells that are printable on large surfaces. In bulk heterojunction (BHJ) OPV devices, organic electron donor and acceptor molecules are intimately mixed within the photoactive layer. Since 2005, the power conversion efficiency of said devices has increased substantially due to insights in the underlying physical processes, device optimization, and chemical engineering of a vast number of novel light‐harvesting organic materials, either small molecules or conjugated polymers. As Nature itself has developed porphyrin chromophores for solar light to energy conversion, it seems reasonable to pursue artificial systems based on the same types of molecules. Porphyrins and their analogues have already been successfully implemented in certain device types, notably in dye‐sensitized solar cells, but they have remained largely unexplored in BHJ organic solar cells. Very recent successes do show, however, the strong (latent) prospects of porphyrinoid semiconductors as light‐harvesting and charge transporting materials in such devices. Here, an overview on the state‐of‐the‐art of porphyrin‐based solution‐processed BHJ OPV is provided and insights are given into the pathways to follow and hurdles to overcome toward further improvements of porphyrinic materials and devices.     

The Importance of Fullerene Percolation in the Mixed Regions of Polymer–Fullerene Bulk Heterojunction Solar Cells

Most optimized donor‐acceptor (D‐A) polymer bulk heterojunction (BHJ) solar cells have active layers too thin to absorb greater than ～80% of incident photons with energies above the polymer's band gap. If the thickness of these devices could be increased without sacrificing internal quantum efficiency, the device power conversion efficiency (PCE) could be significantly enhanced. We examine the device characteristics of BHJ solar cells based on poly(di(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐octylthieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) with 7.3% PCE and find that bimolecular recombination limits the active layer thickness of these devices. Thermal annealing does not mitigate these bimolecular recombination losses and drastically decreases the PCE of PBDTTPD BHJ solar cells. We characterize the morphology of these BHJs before and after thermal annealing and determine that thermal annealing drastically reduces the concentration of PCBM in the mixed regions, which consist of PCBM dispersed in the amorphous portions of PBDTTPD. Decreasing the concentration of PCBM may reduce the number of percolating electron transport pathways within these mixed regions and create morphological electron traps that enhance charge‐carrier recombination and limit device quantum efficiency. These findings suggest that (i) the concentration of PCBM in the mixed regions of polymer BHJs must be above the PCBM percolation threshold in order to attain high solar cell internal quantum efficiency, and (ii) novel processing techniques, which improve polymer hole mobility while maintaining PCBM percolation within the mixed regions, should be developed in order to limit bimolecular recombination losses in optically thick devices and maximize the PCE of polymer BHJ solar cells.     

Correlating Stiffness,Ductility, and Morphology of Polymer:Fullerene Films for Solar Cell Applications

The development of flexible and physically robust organic solar cells requires detailed knowledge of the mechanical behavior of the heterogeneous material stack. However, in these devices there has been limited research on the mechanical properties of the active organic layer. Here, two critical mechanical properties, stiffness and ductility, of a widely studied organic solar cell active layer, a blend film composed of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl C61‐butyric acid methyl ester (PCBM) are reported. Processing conditions are varied to produce films with differing morphology and correlations are developed between the film morphology, mechanical properties and photovoltaic device performance. The morphology is characterized by fitting the absorption of the P3HT:PCBM films to a weakly interacting H‐aggregate model. The elastic modulus is determined using a buckling metrology approach and the crack onset strain is determined by observing the film under tensile strain using optical microscopy. Both the elastic modulus and crack onset strain are found to vary significantly with processing conditions. Processing methods that result in improved device performance are shown to decrease both the compliance and ductility of the film.     

Multiple Cases of Efficient Nonfullerene Ternary Organic Solar Cells Enabled by an Effective Morphology Control Method

Ternary organic solar cells (OSCs) have attracted much research attention, as they can maintain the simplicity of the single‐junction device architecture while broadening the absorption range of OSCs. However, one main challenge that limits the development of ternary OSCs is the difficulty in controlling the morphology of ternary OSCs. In this paper, an effective approach to control the morphology is presented that leads to multiple cases of efficient nonfullerene ternary OSCs with efficiencies of up to 11.2%. This approach is based on a donor polymer with strong temperature dependent aggregation properties processed from hot solutions without any solvent additives and a pair of small molecular acceptors (SMAs) that have similar surface tensions and thus low propensity to form discrete phases. Such a ternary blend exhibits a simplified bulk‐heterojunction morphology that is similar to the morphology of previously reported binary blends. As a result, an almost linear relationship between V_OC and film composition is observed for all nonfullerene ternary devices. Meanwhile, by carefully designing a control system with a large interfacial tension, a different phase separation and V_OC dependence is demonstrated. This morphology control approach can be applicable to more material systems and accelerates the development of the ternary OSC field.     

Synergic Interface and Optical Engineering for High‐Performance Semitransparent Polymer Solar Cells

In this study the thickness of the PTB7‐Th:PC₇₁BM bulk heterojunction (BHJ) film and the PF3N‐2TNDI electron transport layer (ETL) is systematically tuned to achieve polymer solar cells (PSCs) with optimized power conversion efficiency (PCE) of over 9% when an ultrathin BHJ of 50 nm is used. Optical modeling suggests that the high PCE is attributed to the optical spacer effect from the ETL, which not only maximizes the optical field within the BHJ film but also facilitates the formation of a more homogeneously distributed charge generation profile across the BHJ film. Experimentally it is further proved that the extra photocurrent produced at the PTB7‐Th/PF3N‐2TNDI interface also contributes to the improved performance. Taking advantage of this high performance thin film device structure, one step further is taken to fabricate semitransparent PSCs (ST‐PSCs) by using an ultrathin transparent Ag cathode to replace the thick Ag mirror cathode, yielding a series of high performance ST‐PSCs with PCEs over 6% and average visible transmittance between 20% and 30%. These ST‐PSCs also possess remarkable transparency color perception and rendering properties, which are state‐of‐the‐art and fulfill the performance criteria for potential use as power‐generating windows in near future.     

Synergistic Impact of Solvent and Polymer Additives on the Film Formation of Small Molecule Blend Films for Bulk Heterojunction Solar Cells

The addition of polystyrene (PS), a typical insulator, is empirically shown to increase the power conversion efficiencies (PCEs) of a solution‐deposited bulk heterojunction (BHJ) molecular blend film used in solar cell fabrication: p‐DTS(FBTTh₂)₂/PC₇₁BM. The performance is further improved by small quantities of diiodooctane (DIO), an established solvent additive. In this study, how the addition of PS and DIO affects the film formation of this bulk heterojunction blend film are probed via in situ monitoring of absorbance, thickness, and crystallinity. PS and DIO additives are shown to promote donor crystallite formation on different time scales and through different mechanisms. PS‐containing films retain chlorobenzene solvent, extending evaporation time and promoting phase separation earlier in the casting process. This extended time is insufficient to attain the morphology for optimal PCE results before the film sets. Here is where the presence of DIO comes into play: its low vapor pressure further extends the time scale of film evolution and allows for crystalline rearrangement of the donor phase long after casting, ultimately leading to the best BHJ organization.     

Alkyl Chain Engineering of Solution‐Processable Star‐Shaped Molecules for High‐Performance Organic Solar Cells

The impact of alkyl side‐chain substituents on conjugated polymers on the photovoltaic properties of bulk heterojunction (BHJ) solar cells has been studied extensively, but their impact on small molecules has not received adequate attention. To reveal the effect of side chains, a series of star‐shaped molecules based on a triphenylamine (TPA) core, bithiophene, and dicyanovinyl units derivatized with various alkyl end‐capping groups of methyl, ethyl, hexyl and dodecyl is synthesiyed and studied to comprehensively investigate structure‐properties relationships. UV‐vis absorption and cyclic voltammetry data show that variations of alkyl chain length have little influence on the absorption and highest occupied molecular orbital (HOMO)‐lowest unoccupied molecular orbital (LUMO) levels. However, these seemingly negligible changes have a pronounced impact on the morphology of BHJ thin films as well as their charge carrier separation and transportation, which in turn influences the photovoltaic properties of these small‐molecule‐based BHJ devices. Solution‐processed organic solar cells (OSCs) based on the small molecule with the shortest methyl end groups exhibit high short circuit current (J_sc) and fill factor (FF), with an efficiency as high as 4.76% without any post‐treatments; these are among the highest reported for solution‐processed OSCs based on star‐shaped molecules.