Cylindrical Direct‐Current Triboelectric Nanogenerator with Constant Output Current

In this article, a cylindrical direct‐current triboelectric nanogenerator (DC‐TENG) that can generate an almost constant current output with a low crest factor by phase coupling is reported for the first time. Here, the influence of phases (P) and groups (G) on the DC‐TENG is investigated. Experiments show that the crest factor of current, significantly decreases as the phases increase, and the output performance significantly increases as the groups increase. One phase triboelectric power‐generating unit of the DC‐TENG with three‐phase and five‐group (3P5G) produces an open‐circuit voltage of 149.5 V, short‐circuit current 7.3 μA, and transferred charge of 56.7 nC at 600 rpm. The DC‐TENG can produce a coupling current of 21.6 μA and the average output power of 2.04 mW after each phase output is rectified and superimposed. Additionally, the crest factor of output current is reduced to 1.08, and the high‐performance characteristics of an almost constant direct‐current is achieved. The research is of considerable significance to the practical applications of TENGs in powering sensors of low consumption.     

Rotating‐Disk‐Based Direct‐Current Triboelectric Nanogenerator

An innovative design is reported of a direct‐current triboelectric nanogenerator (DC‐TENG) based on a rotating disk design for harvesting rotational mechanical energy. The DC‐TENG consists of two disks and two pairs of flexible electric brushes that are made of carbon fiber and contact two electrodes, respectively. During the rotation, two disks have distinct triboelectric polarities for a cyclic in‐plane charge separation between them and an alternating current is generated between the two electrodes. Because of the sliding contact and automatically switch between the electric brushes and the two electrodes, the current is reversed in the second half of the cycle and a direct current is generated. The role that the rotating speed and the segmentation number have is thoroughly investigated and shows that there is direct current enhancement not only at higher speed but also with more segments. The DC‐TENG has been demonstrated as a constant current source for directly and continuously driving electronic devices and/or charging an energy storage unit without a rectifier bridge. This work presents a novel DC‐TENG technology and opens up more potential applications for harvesting rotational mechanical energy and powering electronics.     

Multiple‐Frequency High‐Output Triboelectric Nanogenerator Based on a Water Balloon for All‐Weather Water Wave Energy Harvesting

Energy and the environment are two of the main issues facing the world today. As a consequence abundant renewable green energy sources such as wave energy, have become hot topics. Here, a multiple‐frequency triboelectric nanogenerator based on the water balloon (WB‐TENG) is proposed for harvesting water wave energy in any direction. Owing to the high elasticity of the water balloon, the WB‐TENG can realize a multiple‐frequency response to low‐frequency external mechanical simulations to generate high‐frequency electrical output. In addition, the water balloon can achieve self‐support without any additional supporting structure because of its tension, to make WB‐TENG still produce electrical output under slight vibration, which can also bring high energy conversion efficiency. Moreover, the fabricated WB‐TENG generates a maximum instantaneous short‐circuit current and an open‐circuit voltage of 147 µA and 1221 V, respectively. Most noteworthy, under the same conditions, the total transferred charge of WB‐TENG is 28 times than that of traditional TENG based on double plate structure during one working cycle. Therefore, this design can provide an effective way to promote the development of TENGs in blue energy.     

Multilayered‐Electrode‐Based Triboelectric Nanogenerators with Managed Output Voltage and Multifold Enhanced Charge Transport

The open‐circuit voltage of a triboelectric nanogenerator (TENG) increases with the tribo‐charge density and the separated distance between two tribo‐surfaces, which can reach several thousand volts and is much higher than the working voltage required by most electrical devices and energy storage units. Therefore, improving the effective efficiency of TENGs requires reducing the output voltage and enhancing the transferred charges. Here, a multilayered‐electrode‐based TENG (ME‐TENG) is developed in which the output voltage can be managed by controlling the charge flow in a process of multiple (N) steps, which results in N times lower voltage but N times higher total charge transport. The ME‐TENG is demonstrated to work in various modes, including multichannel, single‐channel, and double‐tribo‐surface structures. The effects of insulator layer thickness and total layer number on the output voltage are simulated by the finite element method. The output voltage can be modulated from 14 to 102 V by changing the insulator layer number between two adjacent working electrodes, based on which the 8‐bit logic representations of the characters in the ACSII code table are demonstrated. The ME‐TENG provides a novel method to manage the output power and has potential applications in self‐powered sensors array and human–machine interfacing with logic communications.     

Environmentally Friendly Hydrogel‐Based Triboelectric Nanogenerators for Versatile Energy Harvesting and Self‐Powered Sensors

Triboelectric nanogenerators (TENGs), as a promising energy harvesting technology, have been rapidly developed in recent years. However, the research based on fully flexible and environmentally friendly TENGs is still limited. Herein, for the first time, a hydrogel‐based triboelectric nanogenerator (Hydrogel‐TENG) with high flexibility, recyclability, and environmental friendliness simultaneously has been demonstrated. The standard Hydrogel‐TENG can generate a maximum output power of 2 mW at a load resistance of 10 MΩ. The tube‐shaped Hydrogel‐TENG can harvest mechanical energy from various human motions, including bending, twisting, and stretching. Furthermore, the system can serve as self‐powered sensors to detect the human motions. Additionally, the utilized Polyvinyl Alcohol hydrogel employed in this study is recyclable to benefit for fabricating the renewable TENG. The open‐circuit voltage of renewed hydrogel‐TENG can reach up to 92% of the pristine output voltage. This research will pave a potential approach for the development of flexible energy sources and self‐powered motion sensors in environmentally friendly way.     

Metal–Organic Framework: A Novel Material for Triboelectric Nanogenerator–Based Self‐Powered Sensors and Systems

The triboelectric nanogenerator (TENG) offers a simple and cost‐effective method to harness waste energy and works on the principle of contact electrification and electrostatic induction. The performance and application of TENG depend to a great extent on the material used for fabrication. The most widely used materials include polymers and a few metals, well‐arranged in the triboelectric series so as to promote electrification upon contact. New triboelectric materials are important for extending the applications and specificity of the TENG. A TENG based on a metal–organic framework (MOF) of the zeolitic imidazole family is reported here. The zeolitic imidazole framework‐8 (ZIF‐8) and Kapton are used as the active materials for MOF–TENG fabrication. Surface potential, structural, morphological and electrical measurements reveals detailed characteristics of ZIF‐8, confirming the MOF as a potential candidate for TENG applications. The MOF–TENG generates a sustainable output of 164 V and 7 µA in vertical contact–separation mode. Finally, a self‐powered UV counterfeit system and a tetracycline sensor are successfully developed and demonstrated with the MOF–TENG. The sensor is highly selective and reusable simply by washing.     

A Stretchable Nanogenerator with Electric/Light Dual‐Mode Energy Conversion

As an alternative technology, stretchable electronics attract long‐lasting attention. A newly‐designed stretchable nanogenerator with unique dual‐mode energy conversion is reported. The ability of converting the input mechanical stimuli to either electric or light output is achieved by monolithically integrating a transparent single‐electrode triboelectric nanogenerator (S‐TENG) with a ZnS based mechanoluminescence (ML) composite. This stretchable device with versatile functions promotes the development of the smart systems to efficiently and diversely utilize ubiquitous mechanical energy and demonstrates great potential for artificial e‐skins.     

Direct‐Current Triboelectric Nanogenerator Realized by Air Breakdown Induced Ionized Air Channel

The air breakdown phenomenon is generally considered as a negative effect in previous research on triboelectric nanogenerators (TENGs), which is always accompanied by air ionization. Here, by utilizing the air breakdown induced ionized air channel, a direct‐current triboelectric nanogenerator (DC‐TENG) is designed for harvesting contact‐separation mechanical energy. During working process, the charges first transfer from bottom to top electrodes through an external circuit in contact state, then flow back via the ionized air channel created by air breakdown in the separation process. So a unidirectional flow of electrical charges can be observed in the external circuit. With repeating contact‐separation cycles, continuous pulsed DC output through the external circuit can be realized. This working mechanism was verified by real‐time electrode potential monitoring, photocurrent signal detection, and controllable discharging observation. The DC‐TENG can be used for directly and continuously charging an energy storage unit and/or driving electronic devices without using a bridge rectifier. Owing to its simplicity in structure, the mechanism is further applied to fabricate the first flexible DC‐TENG. This research provides a significant fundamental study for DC‐TENG technology and may expand its application in flexible electronics and flexible self‐charging power systems.     

Dual‐Tube Helmholtz Resonator‐Based Triboelectric Nanogenerator for Highly Efficient Harvesting of Acoustic Energy

An acoustic wave is a type of energy that is clean and abundant but almost totally unused because of its very low density. This study investigates a novel dual‐tube Helmholtz resonator‐based triboelectric nanogenerator (HR‐TENG) for highly efficient harvesting of acoustic energy. This HR‐TENG is composed of a Helmholtz resonant cavity, a metal film with evenly distributed acoustic holes, and a dielectric soft film with one side ink‐printed for electrode. Effects of resonant cavity structure, acoustic conditions, and film tension on the HR‐TENG performance are investigated systematically. By coupling the mechanisms of triboelectric nanogenerator and acoustic propagation, a theoretical guideline is provided for improving energy output and broadening the frequency band. Specifically, the present HR‐TENG generates the maximum acoustic sensitivity per unit area of 1.23 VPa^?1 cm^?2 and the maximum power density per unit sound pressure of 1.82 WPa^?1 m^?2, which are higher than the best results from the literature by 60 and 20%, respectively. In addition, the HR‐TENG may also serve as a self‐powered acoustic sensor.     

Capacitor‐Integrated Triboelectric Nanogenerator Based on Metal–Metal Contact for Current Amplification

The electrical power of triboelectric nanogenerators (TENGs) is increased by surface modifications, and they can successfully power portable devices alone. However, modifying the material and its surface may limit the device lifetime, and most of the portable applications demonstrated in previous studies have excessive input conditions. In this study, a capacitor‐integrated TENG (CI‐TENG) that uses the fundamental mechanisms of the Leyden jar is developed. In this device, a long sheet metal (capacitor electrode)–polymer–metal composite (TENG electrode) is rolled inside the casing cylinder, and a capacitor unit is fabricated at the end of the sheet composite. This new operating mechanism of the CI‐TENG is analyzed in terms of the dielectric constant of the capacitor unit and the metal‐to‐metal contact between electrodes. By instantaneous charging and discharging of the capacitor unit inside the CI‐TENG, it can generate a peak open‐circuit voltage of 156 V and a peak closed‐circuit current of 4.3 mA under manual input. It charges a capacitor more than three times faster than a conventional TENG does. Furthermore, the internal impedance of the CI‐TENG is decreased to 200 kΩ without any external circuit.     

Long‐Lifetime Triboelectric Nanogenerator Operated in Conjunction Modes and Low Crest Factor

The high‐output triboelectric nanogenerator (TENG) is indispensable for its practical applications toward industrial products. However, the electricity loss in simple parallel connection among all units and the typically high crest factor output seriously hamper the practical applications of TENG. Here, a rectified TENG is reported in parallel structure to solve the problem of electricity loss in simple parallel connection. The rotational contact–separation structure with phase difference between rectified TENGs addresses high crest factor output and extends service life of rotational TENG simultaneously. The current crest factor is dramatically decreased to 1.31 in multiple rectifier multiple TENG in parallel (MRM‐TENG), while that of TENG in simple parallel is higher than 6. Meanwhile, the current output can retain up to ≈93% of its initial performance after 7 200 000 rotations under 2.00 r s^?1 of 1000 h. Furthermore, the equivalent current can be in linear growth with low crest factor by making MRM‐TENG in parallel for distributed energy supply without electricity loss. This work may provide a new strategy for TENG in parallel to achieve a low crest factor output and long‐term cycling stability power generation in distributed energy harvesting for large‐scale power application.     

Enhancing the Output Performance of Triboelectric Nanogenerator via Grating‐Electrode‐Enabled Surface Plasmon Excitation

The surface charge density and the output impedance of triboelectric nanogenerators (TENGs) are two critical factors for TENGs to speed up their commercialization, so it is important to explore unique methods to reduce the output impedance and increase the surface charge density. Here, an approach is demonstrated to effectively boost the output performance of TENG while reducing the output impedance of TENGs by utilizing grating‐electrode‐enabled surface plasmon excitation. A sustainable and enhanced output performance of about 40 µA (short‐circuit current) and 350 V (peak‐to‐peak voltage at a resistance of 10 MΩ) is produced via grating‐coupled surface plasmon resonance on the TENG with the aluminum grating electrode in the line density of 600 lines mm^?1, and it delivers a peak output power of 3.6 mW under a loading resistance of 1 MΩ, giving over 4.5‐fold enhancement in output power and a 75% reduction in the output impedance. Finally a self‐powered ultrasonic ranging system is utilized to verify the capability of the TENG in powering portable electrics.     

An Ultrathin Flexible Single‐Electrode Triboelectric‐Nanogenerator for Mechanical Energy Harvesting and Instantaneous Force Sensing

The trends in miniaturization of electronic devices give rise to the attention of energy harvesting technologies that gathers tiny wattages of power. Here this study demonstrates an ultrathin flexible single electrode triboelectric nanogenerator (S‐TENG) which not only could harvest mechanical energy from human movements and ambient sources, but also could sense instantaneous force without extra energy. The S‐TENG, which features an extremely simple structure, has an average output current of 78 μA, lightening up at least 70 LEDs (light‐emitting diode). Even tapped by bare finger, it exhibits an output current of 1 μA. The detection sensitivity for instantaneous force sensing is about 0.947 μA MPa^?1. Performances of the device are also systematically investigated under various motion types, press force, and triboelectric materials. The S‐TENG has great application prospects in sustainable wearable devices, sustainable medical devices, and smart wireless sensor networks owning to its thinness, light weight, energy harvesting, and sensing capacities.     

Wireless Electric Energy Transmission through Various Isolated Solid Media Based on Triboelectric Nanogenerator

Wireless electric energy transmission is an important energy supply technology. However, most wireless energy supply based on electromagnetic induction cannot be used for energy transmission through a metal chamber. Herein, a novel idea for wireless electric energy transmission through various isolated solid media based on triboelectric nanogenerator (TENG) is presented. The electric energy is first transformed into mechanical vibration energy in mechanical wave that can propagate well in solid medium, and then the vibration energy is harvested by a TENG. By employing the spring steel sheets and freestanding triboelectric‐layer structure, the vibration TENG as an energy conversion unit has the advantages of high efficiency and facilitation, boosting this wireless energy transmission technology to be an alternative way of delivering electric energy through metal medium. The working principle and output performance have been systematically studied. A commercial capacitor can be charged from 0 to 10 V in 33 and 86 s isolated by an acrylic plate and a copper plate in thickness of 3 mm, respectively. The wireless electric transmission technology is also applied to deliver electric energy into a vacuum glove box and across glass wall successfully. This novel technology has great potential applications in implantable microelectronic devices, encrypted wireless communication, and even nondestructive testing.     

A Water‐Proof Triboelectric–Electromagnetic Hybrid Generator for Energy Harvesting in Harsh Environments

Packaging is a critical aspect of triboelectric nanogenerators (TENG) toward practical applications, since the performance of TENG is greatly affected by environmental conditions such as humidity. A waterproof triboelectric–electromagnetic hybrid generator (WPHG) for harvesting mechanical energy in harsh environments is reported. Since the mechanical transmission from the external mechanical source to the TENG is through a noncontact force between the paired magnets, a fully isolated packaging of TENG part can be easily achieved. At the same time, combining with metal coils, these magnets can be fabricated to be electromagnetic generators (EMG). The characteristics and advantages of outputs from both TENG and EMG are systematically studied and compared to each other. By using transformers and full‐wave rectifiers, 2.3 mA for total short‐circuit current and 5 V for open‐circuit voltage are obtained for WPHG under a rotation speed of 1600 rpm, and it can charge a supercapacitor (20 mF) to 1 V in 22s. Finally, the WPHG is demonstrated to harvest wind energy in the rainy condition and water‐flow energy under water. The reported WPHG renders an effective and sustainable technology for ambient mechanical energy harvesting in harsh environments. Solid progress in both the packaging of TENG and the practical applications of the hybrid generator toward practical power source and self‐powered systems is presented.     

Ion‐Enhanced Field Emission Triboelectric Nanogenerator

As interest in triboelectric nanogenerators (TENGs) continues to increase, some studies have reported that certain limitations exist in TENG due to high potential difference, resulting in air breakdown and field emission. In addition, with known limitations such as extremely low voltage at low external resistance, a breakthrough is required to overcome the limitations of TENG. Here, a new TENG mechanism is reported, utilizing ion‐enhanced field emission (IEFE). Using a simple IEFE‐inducing layer, which consists of a charge accumulation layer and a metal‐to‐metal contact point, electrons can flow directly to a counter electrode while generating high‐output power. Under vertical contact–separation input, the generated root mean square (RMS) power of IEFE‐TENG is 635% higher compared to conventional TENG. As the fundamental mechanism of the IEFE‐TENG is based on installing this simple IEFE‐inducing layer, the power output of existing TENGs including sliding mode types can be boosted. This new TENG mechanism can be a new standard for metal–metal contact TENGs to effectively amplify the output power and to overcome potential limitations.     

Unity Convoluted Design of Solid Li‐Ion Battery and Triboelectric Nanogenerator for Self‐Powered Wearable Electronics

Wearable electronics suffer from severe power shortage due to limited working time of Li‐ion batteries, and there is a desperate need to build a hybrid device including energy scavenging and storing units. However, previous attempts to integrate the two units are mainly based on simple external connections and assembly, so that maintaining small volume and low manufacturing cost becomes increasingly challenging. Here a convoluted power device is presented by hybridizing internally a solid Li‐ion battery (SLB) and a triboelectric nanogenerator (TENG), so that the two units are one inseparable entity. The fabricated device acts as a TENG that can deliver a peak output power of 7.4 mW under a loading resistance of 7 MΩ, while the device also acts as an SLB to store the obtained electric energy. The device can be mounted on a human shoe to sustainably operate a green light‐emitting diode, thus demonstrating potential for self‐powered wearable electronics.     

Mechanical Regulation Triboelectric Nanogenerator with Controllable Output Performance for Random Energy Harvesting

Recycling of random mechanical energy in the environment has become an important research hotspot. The triboelectric nanogenerators (TENGs) were invented to harvest energy, and have been widely applied due to their simple structure, small size, and low cost. This paper reports a mechanical regulation triboelectric nanogenerator (MR‐TENG) for the first time with controllable output performance used to harvest random or irregular energy in the environment. It comprises a transmission unit, switch structure, generator unit, flywheel, and shell. Random linear motion or rocking motion is transferred via the transmission unit to the flywheel. The rotor of the generator unit fixed on the flywheel and the stator of the generator unit fixed on the shell combine. By controlling the storage and release of energy in the flywheel, the switch structure assists the flywheel to convert random or irregular energy into a controllable and stable energy output. The MR‐TENG can generate an open‐circuit voltage of 350 V, a short‐circuit current of 12 μA, a transfer charge of 130 nC, and a peak power of 2.52 mW. Furthermore, a thermometer and more than 300 light emitting diodes (LEDs) are separately powered by this MR‐TENG in simulated water waves, demonstrating its potential application in water wave energy harvesting.     

Triboelectric Nanogenerator for Sustainable Wastewater Treatment via a Self‐Powered Electrochemical Process

By harvesting the flowing kinetic energy of water using a rotating triboelectric nanogenerator (R‐TENG), this study demonstrates a self‐powered wastewater treatment system that simultaneously removes rhodamine B (RhB) and copper ions through an advanced electrochemical unit. With the electricity generated by R‐TENG, the removal efficiency (RE) of RhB can reach the vicinity of 100% within just 15 min when the initial concentration of RhB is around 100 ppm at optimized conditions. The removal efficiency of copper ions can reach 97.3% after 3 h within an initial concentration of 150 ppm at an optimized condition. Importantly, a better performance and higher treating efficiency are found by using the pulsed output of R‐TENG than those using direct current (DC) supply for pollutant removal when consuming equal amount of energy. The recovered copper layer on the cathode through R‐TENG is much denser, more uniform, and with smaller grain size (d = 20 nm) than those produced by DC process, which also hints at very promising applications of the R‐TENG in electroplating industry. In light of the merits such as easy portability, low cost, and effectiveness, this R‐TENG‐based self‐powered electrochemical system holds great potential in wastewater treatment and electroplating industry.     

Boosting Photoelectrochemical Water Splitting by TENG‐Charged Li‐Ion Battery

The need for cost‐effective and sustainable power supplies has spurred a growing interest in hybrid energy harvesting systems, and the most elementary energy production process relies on intermittent solar power. Here, it is shown how the ambient mechanical energy leads to water splitting in a photoelectrochemical (PEC) cell boosted by a triboelectric nanogenerator (TENG). In this strategy, a flexible TENG collects and transforms mechanical energy into electric current, which boosts the PEC water splitting via the charged Li‐ion battery. Au nanoparticles are deposited on TiO₂ nanoarrays for extending the available light spectrum to visible part by surface plasmon resonance effect, which yields a photocurrent density of 1.32 mA cm^?2 under AM 1.5 G illumination and 0.12 mA cm^?2 under visible light with a bias of 0.5 V. The TENG‐charged battery boosts the water splitting performance through coupling electrolysis and enhanced electron–hole separation efficiency. The hybrid cell exhibits an instantaneous current more than 9 mA with a working electrode area of 0.3 cm², suggesting a simple but efficient route for simultaneously converting solar radiation and mechanical energy into hydrogen.