Rapid formation of hydrogen-producing granules in an anaerobic continuous stirred tank reactor induced by acid incubation

A novel approach to rapidly initiate granulation of hydrogen-producing sludge was developed in an anaerobic continuous stirred tank reactor at 37 degrees C. To induce microbial granulation, the acclimated culture was subject to an acid incubation for 24 h by shifting the culture pH from 5.5 to 2.0. The culture was resumed to pH 5.5 after the incubation and the reactor was operated at hydraulic retention times (HRTs) of 12, 6, 2, 1, and 0.5 h in sequence. Microbial aggregation took place immediately with the initiation of acid incubation and granules were developed at 114 h. No granule was observed in the absence of acid incubation in the control test. Changing the culture pH resulted in improvement in surface physicochemical properties of the culture favoring microbial granulation. The zeta potential increased from -11.6 to -3.5 mV, hydrophobicity in terms of contact angle improved from 31 degrees to 43 degrees and extracellular proteins/polysaccharides ratio increased from 0.2 to 0.5-0.8. Formation of granular sludge facilitated biomass retention of up to 32.2 g-VSS/L and enhanced hydrogen production. The hydrogen production rate and hydrogen yield increased with the reduction in HRT at an influent glucose concentration of 10 g/L once steady granular sludge layer was formed, achieving the respective peaks of 3.20 L/L x h and 1.81 mol-H(2)/mol-glucose at 0.5 h HRT. The experimental results suggested that acid incubation was able to initiate the rapid formation of hydrogen-producing granules by regulating the surface characteristics of microbial aggregates in a well-mixed reactor, which enhanced the hydrogen production.     

Comparative analysis of hydrogen-producing bacterial biofilms and granular sludge formed in continuous cultures of fermentative bacteria

A system for biohydrogen production was developed based on long-term continuous cultures grown on sugar beet molasses in packed bed reactors. In two separate cultures, consortia of fermentative bacteria developed as biofilms on granitic stones. In one of the cultures, a granular sludge was also formed. Metagenomic analysis of the microbial communities by 454-pyrosequencing of amplified 16S rDNA fragments revealed that the overall biodiversity of the hydrogen-producing cultures was quite small. The stone biofilm from the culture without granular sludge was dominated by Clostridiaceae and heterolactic fermentation bacteria, mainly Leuconostocaeae. Representatives of the Leuconostocaeae and Enterobacteriaceae were dominant in both the granules and the stone biofilm formed in the granular sludge culture. The culture containing granular sludge produced hydrogen significantly more effectively than that containing only the stone biofilm: 5.43 vs. 2.8 mol H₂/mol sucrose from molasses, respectively. The speculations that lactic acid bacteria may favor hydrogen production are discussed.     

Starter culture of <Emphasis Type="Italic">Pseudomonas veronii</Emphasis> strain B for aerobic granulation

Aggregation of bacterial cells is used in formation of microbial granules. Aerobically grown microbial granules can be used as the bio-agents in the treatment of wastewater. However, there are problems with start up of microbial granulation and biosafety of this process. Aim of this research was selection and testing of safe microbial strain with high cell aggregation ability to shorten period of microbial granules formation. Five bacterial strains with cell aggregation index higher than 50% have been isolated from the granules. Strain of Pseudomonas veronii species was considered as most probably safe starter culture for granulation because other strains belonged to the species known as human pathogens. The microbial granules were formed after 3 days of cultivation in case when P. veronii strain B was applied to start-up aerobic granulation process using model wastewater. The granules were produced from activated sludge after 9 days of cultivation. Microbial aggregates produced from starter culture of P. veronii strain B were more compact (sludge volume index was 70 ml/g) than those produced from activated sludge (sludge volume index was 106 ml/g). It is a first proof that application of selected safe starter pure culture with high cell aggregation ability can accelerate and enhance formation of microbial granules.     

Depth penetration and detection of pH gradients in biofilms by two-photon excitation microscopy.

Deep microbial biofilms are a major problem in many industrial, environmental, and medical settings. Novel approaches are needed to understand the structure and metabolism of these biofilms. Two-photon excitation microscopy (TPE) and conventional confocal laser scanning microscopy (CLSM) were compared quantitatively for the ability to visualize bacteria within deep in vitro biofilms. pH gradients within these biofilms were determined by fluorescence lifetime imaging, together with TPE. A constant-depth film fermentor (CDFF) was inoculated for 8 h at 50 ml. h(-1) with a defined mixed culture of 10 species of bacteria grown in continuous culture. Biofilms of fixed depths were developed in the CDFF for 10 or 11 days. The microbial compositions of the biofilms were determined by using viable counts on selective and nonselective agar media; diverse mixed-culture biofilms developed, including aerobic, facultative, and anaerobic species. TPE was able to record images four times deeper than CLSM. Importantly, in contrast to CLSM images, TPE images recorded deep within the biofilm showed no loss of contrast. The pH within the biofilms was measured directly by means of fluorescence lifetime imaging; the fluorescence decay of carboxyfluorescein was correlated with biofilm pH and was used to construct a calibration curve. pH gradients were detectable, in both the lateral and axial directions, in steady-state biofilms. When biofilms were overlaid with 14 mM sucrose for 1 h, distinct pH gradients developed. Microcolonies with pH values of below pH 3.0 were visible, in some cases adjacent to areas with a much higher pH (>5.0). TPE allowed resolution of images at significantly greater depths (as deep as 140 microm) than were possible with CLSM. Fluorescence lifetime imaging allowed the in situ, real-time imaging of pH and the detection of sharp gradients of pH within microbial biofilms.     

The effects of glutaraldehyde on the control of single and dual biofilms of Bacillus cereus and Pseudomonas fluorescens

Glutaraldehyde (GLUT) was evaluated for control of single and dual species biofilms of Bacillus cereus and Pseudomonas fluorescens on stainless steel surfaces using a chemostat system. The biofilms were characterized in terms of mass, cell density, total and matrix proteins and polysaccharides. The control action of GLUT was assessed in terms of inactivation and removal of biofilm. Post-biocide action was characterized 3, 7, 12, 24, 48 and 72 h after treatment. Tests with planktonic cells were also performed for comparison. The results demonstrated that in dual species biofilms the metabolic activity, cell density and the content of matrix proteins were higher than those of either single species. Planktonic B. cereus was more susceptible to GLUT than P. fluorescens. The biocide susceptibility of dual species planktonic cultures was an average of each single species. Planktonic cells were more susceptible to GLUT than their biofilm counterparts. Biofilm inactivation was similar for both of the single biofilms while dual biofilms were more resistant than single species biofilms. GLUT at 200 mg l(-1) caused low biofilm removal (<10%). Analysis of the post-biocide treatment data revealed the ability of biofilms to recover their activity over time. However, 12 h after biocide application, sloughing events were detected for both single and dual species biofilms, but were more marked for those formed by P. fluorescens (removal >40% of the total biofilm). The overall results suggest that GLUT exerts significant antimicrobial activity against planktonic bacteria and a partial and reversible activity against B. cereus and P. fluorescens single and dual species biofilms. The biocide had low antifouling effects when analysed immediately after treatment. However, GLUT had significant long-term effects on biofilm removal, inducing significant sloughing events (recovery in terms of mass 72 h after treatment for single biofilms and 42 h later for dual biofilms). In general, dual species biofilms demonstrated higher resistance and resilience to GLUT exposure than either of the single species biofilms. P. fluorescens biofilms were more susceptible to the biocide than B. cereus biofilms.     

Proteome changes in the initial bacterial colonist during ecological succession in an acid mine drainage biofilm community

Proteomes of acid mine drainage biofilms at different stages of ecological succession were examined to understand microbial responses to changing community membership. We evaluated the degree of reproducibility of the community proteomes between samples of the same growth stage and found stable and predictable protein abundance patterns across time and sampling space, allowing for a set of 50 classifier proteins to be identified for use in predicting growth stages of undefined communities. Additionally, physiological changes in the dominant species, Leptospirillum Group II, were analysed as biofilms mature. During early growth stages, this population responds to abiotic stresses related to growth on the acid mine drainage solution. Enzymes involved in protein synthesis, cell division and utilization of 1- and 2-carbon compounds were more abundant in early growth stages, suggesting rapid growth and a reorganization of metabolism during biofilm initiation. As biofilms thicken and diversify, external stresses arise from competition for dwindling resources, which may inhibit cell division of Leptospirillum Group II through the SOS response. This population also represses translation and synthesizes more complex carbohydrates and amino acids in mature biofilms. These findings provide unprecedented insight into the physiological changes that may result from competitive interactions within communities in natural environments.     

厌氧产氢颗粒污泥蛋白质组分析样品的高效制备方法

【背景】厌氧产氢颗粒污泥比絮状产氢污泥具有更高的生物量、沉降性与反应效率,对颗粒污泥进行蛋白质组学研究,有助于揭示其代谢调控的分子机制,从而对厌氧代谢过程进行优化调控。目前关于产氢颗粒污泥蛋白质组分析样品制备方法的研究尚未见文献报道。革兰氏阳性菌Ethanoligenens harbinense YUAN-3是自凝集产氢发酵细菌,在间歇和连续流培养中可形成自聚集的厌氧颗粒,由于其全基因组信息清楚,可作为模式研究材料对制备方法进行评估。【目的】针对厌氧产氢颗粒污泥的蛋白质组学研究,比较不同蛋白质提取方法进行优化。【方法】分别利用液氮研磨、超声破碎、匀浆破碎对产氢颗粒污泥破碎,比较这3种方法对总蛋白提取量的影响;通过双向电泳比较三氯乙酸(Trichloroacetic acid,TCA)-丙酮沉淀法与苯酚抽提法对总蛋白提取效果的影响;对总蛋白样品分别进行同位素标记相对和绝对定量标记(Isobarictagsforrelativeandabsolutequantification,i TRAQ)、串联质谱标签(Tandemmasstag,TMT)标记以及质谱鉴定。【结果】液氮研磨、超声破碎、匀浆破碎3种破碎方法下总蛋白的提取量分别是对照样品的2.0、3.9与5.2倍。与TCA-丙酮沉淀法相比,苯酚抽提法总蛋白样品在双向电泳图谱上的蛋白质点明显增多,分布均匀,同时其在碱性蛋白端与小分子量蛋白端的蛋白质点也明显增多。质谱分析发现,iTRAQ标记样品与TMT标记样品中分别鉴定到1797个与1644个蛋白,在分子量、等电点、亚细胞定位的各个分布范围内,这些蛋白良好地覆盖了E.harbinenseYUAN-3中各个类型的蛋白。【结论】匀浆破碎与苯酚抽提法联用的总蛋白制备方法更适用于厌氧产氢颗粒污泥,该方法有利于后续的蛋白质双向电泳和定量蛋白质组质谱分析,可作为产氢颗粒污泥以及革兰氏阳性菌总蛋白制备的方法参考。     

Improvement of the anodic bioelectrocatalytic activity of mixed culture biofilms by a simple consecutive electrochemical selection procedure

In this paper we demonstrate that the anodic, bioelectrocatalytic performance of wastewater inoculum based, mixed culture microbial biofilms can be considerably improved by using a consecutive, purely electrochemical selection and biofilm acclimatization procedure. The procedure may represent an alternative to a repetitive mechanical biofilm removal, re-suspension and electrochemically facilitated biofilm formation. By using the proposed technique, the bioelectrocatalytic current density was increased from the primary to the secondary biofilm from 250 microAcm(-2) to about 500 microAcm(-2); and the power density of respective microbial fuel cells could be increased from 686 mWm(-2) to 1487 mWm(-2). The electrochemical characterization of the biofilms reveals a strong similarity to Geobacter sulfurreducens biofilms, which may indicate a dominating role of this bacterium in the biofilms.     

Disinfection of bacterial biofilms in pilot-scale cooling tower systems

The impact of continuous chlorination and periodic glutaraldehyde treatment on planktonic and biofilm microbial communities was evaluated in pilot-scale cooling towers operated continuously for 3 months. The system was operated at a flow rate of 10,080 l day(-1). Experiments were performed with a well-defined microbial consortium containing three heterotrophic bacteria: Pseudomonas aeruginosa, Klebsiella pneumoniae and Flavobacterium sp. The persistence of each species was monitored in the recirculating cooling water loop and in biofilms on steel and PVC coupons in the cooling tower basin. The observed bacterial colonization in cooling towers did not follow trends in growth rates observed under batch conditions and, instead, reflected differences in the ability of each organism to remain attached and form biofilms under the high-through flow conditions in cooling towers. Flavobacterium was the dominant organism in the community, while P. aeruginosa and K. pneumoniae did not attach well to either PVC or steel coupons in cooling towers and were not able to persist in biofilms. As a result, the much greater ability of Flavobacterium to adhere to surfaces protected it from disinfection, whereas P. aeruginosa and K. pneumoniae were subject to rapid disinfection in the planktonic state.     

Depth Penetration and Detection of pH Gradients in Biofilms by Two-Photon Excitation Microscopy

Deep microbial biofilms are a major problem in many industrial, environmental, and medical settings. Novel approaches are needed to understand the structure and metabolism of these biofilms. Two-photon excitation microscopy (TPE) and conventional confocal laser scanning microscopy (CLSM) were compared quantitatively for the ability to visualize bacteria within deep in vitro biofilms. pH gradients within these biofilms were determined by fluorescence lifetime imaging, together with TPE. A constant-depth film fermentor (CDFF) was inoculated for 8 h at 50 ml · h⁻¹ with a defined mixed culture of 10 species of bacteria grown in continuous culture. Biofilms of fixed depths were developed in the CDFF for 10 or 11 days. The microbial compositions of the biofilms were determined by using viable counts on selective and nonselective agar media; diverse mixed-culture biofilms developed, including aerobic, facultative, and anaerobic species. TPE was able to record images four times deeper than CLSM. Importantly, in contrast to CLSM images, TPE images recorded deep within the biofilm showed no loss of contrast. The pH within the biofilms was measured directly by means of fluorescence lifetime imaging; the fluorescence decay of carboxyfluorescein was correlated with biofilm pH and was used to construct a calibration curve. pH gradients were detectable, in both the lateral and axial directions, in steady-state biofilms. When biofilms were overlaid with 14 mM sucrose for 1 h, distinct pH gradients developed. Microcolonies with pH values of below pH 3.0 were visible, in some cases adjacent to areas with a much higher pH (>5.0). TPE allowed resolution of images at significantly greater depths (as deep as 140 μm) than were possible with CLSM. Fluorescence lifetime imaging allowed the in situ, real-time imaging of pH and the detection of sharp gradients of pH within microbial biofilms.     

The electric picnic: synergistic requirements for exoelectrogenic microbial communities

Characterization of the various microbial populations present in exoelectrogenic biofilms provides insight into the processes required to convert complex organic matter in wastewater streams into electrical current in bioelectrochemical systems (BESs). Analysis of the community profiles of exoelectrogenic microbial consortia in BESs fed different substrates gives a clearer picture of the different microbial populations present in these exoelectrogenic biofilms. Rapid utilization of fermentation end products by exoelectrogens (typically Geobacter species) relieves feedback inhibition for the fermentative consortia, allowing for rapid metabolism of organics. Identification of specific syntrophic processes and the communities characteristic of these anodic biofilms will be a valuable aid in improving the performance of BESs.     

Biohydrogen production in granular up-flow anaerobic sludge blanket (UASB) reactors with mixed cultures under hyper-thermophilic temperature (70 degrees C)

Hyper-thermophilic hydrogen production without methane was demonstrated for the first time in granular up-flow anaerobic sludge blanket (UASB) system fed with glucose using mixed cultures. The maximum hydrogen yield in this study was 2.47 +/- 0.15 mol H2/mol glucose. This high yield has never been previously reported in mixed culture systems and it was likely due to more favorable thermodynamic conditions at hyper-thermophilic temperatures. Different start-up strategies (bromoethanosulfonate (BES) addition and flow recycle) were evaluated. BES addition during start-up prevented the establishment of methanogenic cultures in granules. Flow recycle was important to achieve higher hydrogen yield through enriching better hydrogen-producing organisms and reduced the start-up period as well. This study indicated UASB system was a promising system for hydrogen production.     

The microbial ecology of a high-temperature near-neutral spring situated in Rotorua, New Zealand

A combination of both culture and culture-independent techniques were used to investigate the microbial ecology of a near-neutral, high-temperature hot spring (designated AQ1) in Rotorua, New Zealand. The active microbial members of the community were targeted by analyzing biofilms that developed on surfaces incubated in situ in AQ1. Colonization of surfaces was rapid as indicated by ATP assay and microscopic observation. DNA-based analysis of both colonized surfaces and pool water from AQ1 revealed an exclusively archaeal community. Different colonization patterns were observed on glass slides incubated near the pool surface or at depth. Slides incubated at the surface were colonized exclusively by Pyrobaculum species, while at greater depth a novel coccus was also observed and detected by DGGE. Sequence analysis revealed the coccus was related to Aeropyrum pernix. Two microorganisms were isolated from AQ1 pool water, namely Ignisphaera aggregans AQ1.S1(T) and a species of Pyrobaculum, isolate AQ1.S2.     

The application of nitric oxide to control biofouling of membrane bioreactors

A novel strategy to control membrane bioreactor (MBR) biofouling using the nitric oxide (NO) donor compound PROLI NONOate was examined. When the biofilm was pre‐established on membranes at transmembrane pressure (TMP) of 88–90 kPa, backwashing of the membrane module with 80 μM PROLI NONOate for 45 min once daily for 37 days reduced the fouling resistance (R_f) by 56%. Similarly, a daily, 1 h exposure of the membrane to 80 μM PROLI NONOate from the commencement of MBR operation for 85 days resulted in reduction of the TMP and R_f by 32.3% and 28.2%. The microbial community in the control MBR was observed to change from days 71 to 85, which correlates with the rapid TMP increase. Interestingly, NO‐treated biofilms at 85 days had a higher similarity with the control biofilms at 71 days relative to the control biofilms at 85 days, indicating that the NO treatment delayed the development of biofilm bacterial community. Despite this difference, sequence analysis indicated that NO treatment did not result in a significant shift in the dominant fouling species. Confocal microscopy revealed that the biomass of biopolymers and microorganisms in biofilms were all reduced on the PROLI NONOate‐treated membranes, where there were reductions of 37.7% for proteins and 66.7% for microbial cells, which correlates with the reduction in TMP. These results suggest that NO treatment could be a promising strategy to control biofouling in MBRs.     

The effect of a quaternary ammonium biocide on the performance and characteristics of laboratory-scale rotating biological contactors

AIMS: To study the effect of a quaternary ammonium biocide, didecyldimethylammonium chloride (DDAC), on the treatment efficiency of laboratory-scale rotating biological contactors (RBCs) as well as their component biofilms. METHODS AND RESULTS: Biofilms were established on the RBCs and then exposed to 0-160 mg l(-)1 (p.p.m.) DDAC at a flow rate of 2.5 l h(-1). The treatment efficiency of the RBC and the microbial activity of the biofilms were markedly decreased when 40 mg l(-1) DDAC or greater were applied to the units. However, DDAC had no effect on the number of viable bacteria in the biofilms when DDAC concentrations up to 80 mg l(-1) were applied to the RBCs. No viable bacteria could be detected in the biofilm when DDAC was applied at 160 mg l(-1). Extended observation over a further 40 d with 20 and 80 mg l(-1) DDAC showed similar results in terms of chemical oxygen demand removal, ATP content and viability of biofilms compared with those values over the first 12 d of exposure. CONCLUSIONS: There was at least a fourfold difference in the susceptibility of planktonic and sessile bacteria to DDAC. Cells acclimatized to DDAC did not increase their capability to degrade normal carbon sources or DDAC under the conditions used in this study. SIGNIFICANCE AND IMPACT OF THE STUDY: The results show that RBCs can be used to treat effluents containing DDAC at concentrations up to 20 mg l(-1) and that 160 mg l(-1) of DDAC was required to eliminate cells in established biofilms.     

Effects of acid pre-treatment on bio-hydrogen production and microbial communities during dark fermentation

Optimal conditions for acid pre-treatment were investigated for the enrichment of hydrogen-producing bacteria (HPB) in a mixed culture using three strong acids: HCl, HNO(3), and H2SO4 x HCl was selected as a suitable acid for the enrichment of HPB in the fermentation process. The volume of bio-hydrogen produced when the mixed culture was pre-treated using HCl at pH 2 was 3.2 times higher than that obtained without acid pre-treatment. Changes in the microbial community during acid pre-treatment were monitored using images obtained by the fluorescent in situ hybridization (FISH) method and the Live/Dead cell viability test. The tests clearly indicated that the Clostridium species of cluster I were the predominant strains involved in bio-H(2) fermentation, and could be selectively enriched by HCl pre-treatment.     

Biofilm penetration and disinfection efficacy of alkaline hypochlorite and chlorosulfamates

AIMS: The purpose of this study was to compare the efficacy, in terms of bacterial biofilm penetration and killing, of alkaline hypochlorite (pH 11) and chlorosulfamate (pH 5.5) formulations. METHODS AND RESULTS: Two species biofilms of Pseudomonas aeruginosa and Klebsiella pneumoniae were grown by flowing a dilute medium over inclined stainless steel slides for 6 d. Microelectrode technology was used to measure concentration profiles of active chlorine species within the biofilms in response to treatment at a concentration of 1000 mg total chlorine l(-1). Chlorosulfamate formulations penetrated biofilms faster than did hypochlorite. The mean penetration time into approximately 1 mm-thick biofilms for chlorosulfamate (6 min) was only one-eighth as long as for the same concentration of hypochlorite (48 min). Chloride ion penetrated biofilms rapidly (5 min) with an effective diffusion coefficient in the biofilm that was close to the value for chloride in water. Biofilm bacteria were highly resistant to killing by both antimicrobial agents. Biofilms challenged with 1000 mg l(-1) alkaline hypochlorite or chlorosulfamate for 1 h experienced 0.85 and 1.3 log reductions in viable cell numbers, respectively. Similar treatment reduced viable numbers of planktonic bacteria to non-detectable levels (log reduction greater than 6) within 60 s. Aged planktonic and resuspended laboratory biofilm bacteria were just as susceptible to hypochlorite as fresh planktonic cells. CONCLUSION: Chlorosulfamate transport into biofilm was not retarded whereas hypochlorite transport clearly was retarded. Superior penetration by chlorosulfamate was hypothesized to be due to its lower capacity for reaction with constituents of the biofilm. Poor biofilm killing despite direct measurement of effective physical penetration of the antimicrobial agent into the biofilm demonstrates that bacteria in the biofilm are protected by some mechanism other than simple physical shielding by the biofilm matrix. SIGNIFICANCE AND IMPACT OF THE STUDY: This study lends support to the theory that the penetration of antimicrobial agents into microbial biofilms is controlled by the reactivity of the antimicrobial agent with biofilm components. The finding that chlorine-based biocides can penetrate, but fail to kill, bacteria in biofilms should motivate the search for other mechanisms of protection from killing by antimicrobial agents in biofilms.     

Biological hydrogen production in a UASB reactor with granules. I: Physicochemical characteristics of hydrogen-producing granules

Hydrogen-producing granules with an excellent settling ability were cultivated in an upflow anaerobic sludge blanket reactor treating a sucrose-rich synthetic wastewater. The physicochemical characteristics of granules were evaluated in this study. The mature granules had a diameter ranging from 1.0 to 3.5 mm and an average density of 1.036 +/- 0.005 g/mL, whereas they had good settling ability and a high settling velocity of 32-75 m/h. The low ratio of proteins/carbohydrates for the extracellular polymeric substances (EPS) in the granules suggests that carbohydrates rather than proteins, might play a more important role in the formation of the H(2)-producing granules. The contact angle of the mature granules, 54 +/- 2 degrees , was larger than that of the seed sludge (38 +/- 2 degrees ), indicating that the microbial cells in the H(2)-producing granules had higher hydrophobicity. The granules had fractal nature with a fractal dimension of 1.78. Their porosities were in the range of 0-0.70, and increased with increasing granule size. The ratios between the observed and predicted settling velocities by Stokes' law were in a range of 1.00-1.50, and the fluid collection efficiency of the granules ranged from 0 to 0.19, indicating that their permeabilities were lower and that there was little advective flow through their interior. Experimental results also suggest that molecular diffusion appeared to play an important role in the mass transfer through the H(2)-producing granules.     

Anaerobic benzene degradation under denitrifying conditions: Peptococcaceae as dominant benzene degraders and evidence for a syntrophic process

An anaerobic microbial community was enriched in a chemostat that was operated for more than 8 years with benzene and nitrate as electron acceptor. The coexistence of multiple species in the chemostat and the presence of a biofilm, led to the hypothesis that benzene-degrading species coexist in a syntrophic interaction, and that benzene can be degraded in syntrophy by consortia with various electron acceptors in the same culture. The benzene-degrading microorganisms were identified by DNA-stable isotope probing with [U-(13) C]-labelled benzene, and the effect of different electron donors and acceptors on benzene degradation was investigated. The degradation rate constant of benzene with nitrate (0.7 day(-1) ) was higher than reported previously. In the absence of nitrate, the microbial community was able to use sulfate, chlorate or ferric iron as electron acceptor. Bacteria belonging to the Peptococcaceae were identified as dominant benzene consumers, but also those related to Rhodocyclaceae and Burkholderiaceae were found to be associated with the anaerobic benzene degradation process. The benzene degradation activity in the chemostat was associated with microbial growth in biofilms. This, together with the inhibiting effect of hydrogen and the ability to degrade benzene with different electron acceptors, suggests that benzene was degraded via a syntrophic process.     

The effects of glutaraldehyde on the control of single and dual biofilms of Bacillus cereus and Pseudomonas fluorescens

Glutaraldehyde (GLUT) was evaluated for control of single and dual species biofilms of Bacillus cereus and Pseudomonas fluorescens on stainless steel surfaces using a chemostat system. The biofilms were characterized in terms of mass, cell density, total and matrix proteins and polysaccharides. The control action of GLUT was assessed in terms of inactivation and removal of biofilm. Post-biocide action was characterized 3, 7, 12, 24, 48 and 72 h after treatment. Tests with planktonic cells were also performed for comparison. The results demonstrated that in dual species biofilms the metabolic activity, cell density and the content of matrix proteins were higher than those of either single species. Planktonic B. cereus was more susceptible to GLUT than P. fluorescens. The biocide susceptibility of dual species planktonic cultures was an average of each single species. Planktonic cells were more susceptible to GLUT than their biofilm counterparts. Biofilm inactivation was similar for both of the single biofilms while dual biofilms were more resistant than single species biofilms. GLUT at 200 mg l^?1 caused low biofilm removal (<10%). Analysis of the post-biocide treatment data revealed the ability of biofilms to recover their activity over time. However, 12 h after biocide application, sloughing events were detected for both single and dual species biofilms, but were more marked for those formed by P. fluorescens (removal >40% of the total biofilm). The overall results suggest that GLUT exerts significant antimicrobial activity against planktonic bacteria and a partial and reversible activity against B. cereus and P. fluorescens single and dual species biofilms. The biocide had low antifouling effects when analysed immediately after treatment. However, GLUT had significant long-term effects on biofilm removal, inducing significant sloughing events (recovery in terms of mass 72 h after treatment for single biofilms and 42 h later for dual biofilms). In general, dual species biofilms demonstrated higher resistance and resilience to GLUT exposure than either of the single species biofilms. P. fluorescens biofilms were more susceptible to the biocide than B. cereus biofilms.