A performance comparison of choline biosensors: anodic or cathodic detections of H2O2 generated by enzyme immobilized on a conducting polymer

Amperometric choline biosensors were fabricated by the covalent immobilization of an enzyme of choline oxidase (ChO) and a bi-enzyme of ChO/horseradish peroxidase (ChO/HRP) onto poly-5,2′:5′,2″-terthiophene-3′-carboxylic acid (poly-TTCA) modified electrodes (CPMEs). A sensor modified with ChO utilized the oxidation process of enzymatically generated H₂O₂ in a choline solution at +0.6 V. The other one modified with ChO/HRP utilized the reduction process of H₂O₂ in a choline solution at −0.2 V. Experimental parameters affecting the sensitivity of sensors, such as pH, applied potential, and temperature were optimized. A performance comparison of two sensors showed that one based on ChO/HRP/CPME had a linear range from 1.0×10⁻⁶ to 8.0×10⁻⁵ M and the other based on ChO/CPME from 1.0×10⁻⁶ to 5.0×10⁻⁵ M. The detection limits for choline employing ChO/HRP/CPME and ChO/CPME were determined to be about 1.0×10⁻⁷ and 4.0×10⁻⁷ M, respectively. The response time of sensors was less than 5 s. Sensors showed good selectivity to interfering species. The long-term storage stability of the sensor based on ChO/HRP/CPME was longer than that based on ChO/CPME.     

Enzyme-entrapping membranes for biosensors obtained by radiation-induced polymerization

A new method of physically immobilizing enzymes in poly(2-hydroxyethyl methacrylate) membranes was developed in order to obtain suitable biosensors. It was possible to prepare an enzyme sensor based on an oxygen Clark electrode and on glucose oxidase immobilized by low-temperature gamma radiation-induced polymerization. Temperature and pH effects on the activity of immobilized enzyme are described and the response characteristics of the resulting biosensor are summarized. The determination of glucose in standard solutions was carried out and a linear calibration curve, with an R² value of 0·9993, from the detection limit 5 × 10⁻⁵ to 1·2 × 10⁻³ was obtained. The biosensor was employed to analysis of control sera and the results were compared to those obtained by enzymatic-spectrophotometric detection.     

Entrapment of lipase into K-carrageenan beads and its use in hydrolysis of olive oil in biphasic system

The porcine pancrease lipase was immobilized by entrapment in the beads of K-carrageenan and cured by treatment with polyethyleneimine (PEI) in the phosphate buffer. The retention of hydrolytic activity of lipase and compressive strength of the beads were examined. The activity of free and immobilized lipase was assessed by using olive oil as the substrate. The immobilized enzyme exhibited a little shift towards acidic pH for its optimal activity and retained 50% of its activity after 5 cycles. When the enzyme concentration was kept constant and substrate concentration was varied the K_m and V_max were observed to be 0.18 × 10⁻² and 0.10, and 0.10 × 10⁻² and 0.09 respectively, for free and for entrapped enzymes. When the substrate concentration was kept constant and enzyme concentration was varied, the values of K_m and V_max were observed to be 0.19 × 10⁻⁷ and 0.41, and 0.18 × 10⁻⁷ and 0.41 for free and entrapped enzymes. Though this indicates that there is no conformational change during immobilization, it also shows that the reaction velocity depends on the concentration. Immobilized enzyme showed improved thermal and storage stability. Hydrolysis of olive oil in organic–aqueous two-phase system using fixed bed reactor was carried out and conditions were optimized. The enzyme in reactor retained 30% of its initial activity after 480 min (12 cycles).     

Effect of nomegestrol acetate on estrone-sulfatase and 17β-hydroxysteroid dehydrogenase activities in human breast cancer cells

It is well recognized that estradiol (E₂) is one of the most important hormones supporting the growth and evolution of breast cancer. Consequently, to block this hormone before it enters the cancer cell or in the cell itself, has been one of the main targets in recent years. In the present study we explored the effect of the progestin, nomegestrol acetate, on the estrone sulfatase and 17β-hydroxy-steroid dehydrogenase (17β-HSD) activities of MCF-7 and T-47D human breast cancer cells. Using physiological doses of estrone sulfate (E₁S: 5 × 10⁻⁹ M), nomegestrol acetate blocked very significantly the conversion of E₁S to E₂. In the MCF-7 cells, using concentrations of 5 × 10⁻⁶ M and 5 × 10⁻⁵ M of nomegestrol acetate, the decrease of E₁S to E₂ was, respectively, −43% and −77%. The values were, respectively, −60% and −71% for the T-47D cells. Using E₁S at 2 × 10⁻⁶ M and nomegestrol acetate at 10⁻⁵ M, a direct inhibitory effect on the enzyme of −36% and −18% was obtained with the cell homogenate of the MCF-7 and T-47D cells, respectively. In another series of studies, it was observed that after 24 h incubation of a physiological concentration of estrone (E₁: 5 × 10⁻⁹ M) this estrogen is converted in a great proportion to E₂. Nomegestrol acetate inhibits this transformation by −35% and −85% at 5 × 10⁻⁷ M and 5 × 10⁻⁵ M, respectively in T-47D cells; whereas in the MCF-7 cells the inhibitory effect is only significant, −48%, at 5 × 10⁻⁵ M concentration of nomegestrol acetate. It is concluded that nomegestrol acetate in the hormone-dependent MCF-7 and T-47D breast cancer cells significantly inhibits the estrone sulfatase and 17β-HSD activities which converts E₁S to the biologically active estrogen estradiol. This inhibition provoked by this progestin on the enzymes involved in the biosynthesis of E₂ can open new clinical possibilities in breast cancer therapy.     

Catalytic properties of the immobilized Aspergillus tamarii xylanase

Xylanase from Aspergillus tamarii was covalently immobilized on Duolite A147 pretreated with the bifunctional agent glutaraldehyde. The bound enzyme retained 54.2% of the original specific activity exhibited by the free enzyme (120 U/mg protein). Compared to the free enzyme, the immobilized enzyme exhibited lower optimum pH, higher optimum reaction temperature, lower energy of activation, higher K_m (Michaelis constant), lower V_max (maximal reaction rate). The half-life for the free enzyme was 186.0, 93.0, and 50.0 min for 40, 50, and 60°C, respectively, whereas the immobilized form at the same temperatures had half-life of 320, 136, and 65 min. The deactivation rate constant at 60°C for the immobilized enzyme is about 6.0 × 10⁻³, which is lower than that of the free enzyme (7.77 × 10⁻³ min). The energy of thermal deactivation was 15.22 and 20.72 kcal/mol, respectively for the free and immobilized enzyme, confirming stabilization by immobilization. An external mass transfer resistance was identified with the immobilization carrier (Duolite A147). The effect of some metal ions on the activity of the free and immobilized xylanase has been investigated. The immobilized enzyme retained about 73.0% of the initial catalytic activity even after being used 8 cycles.     

Amperometric glucose biosensor based on self-assembly hydrophobin with high efficiency of enzyme utilization

Hydrophobins are a family of natural self-assembling proteins with high biocompability, which are apt to form strong and ordered assembly onto many kinds of surfaces. These physical-chemical and biological properties make hydrophobins suitable for surface modification and biomolecule immobilization purposes. A class II hydrophobin HFBI was used as enzyme immobilization matrix on platinum electrode to construct amperometric glucose biosensor. Permeability of HFBI self-assembling film was optimized by selecting the proper HFBI concentration for electrode modification, in order to allow H₂O₂ permeating while prevent interfering compounds accessing. HFBI self-assembly and glucose oxidase (GOx) immobilization was monitored by quartz crystal microbalance (QCM), and characterization of the modified electrode surface was obtained by scanning electron microscope (SEM). The resulting glucose biosensors showed rapid response time within 6 s, limits of detection of 0.09 mM glucose (signal-to-noise ratio = 3), wide linear range from 0.5 to 20 mM, high sensitivity of 4.214 × 10⁻³ A M⁻¹ cm⁻², also well selectivity, reproducibility and lifetime. The all-protein modified biosensor exhibited especially high efficiency of enzyme utilization, producing at most 712 μA responsive current for per unit activity of GOx. This work provided a promising new immobilization matrix with high biocompatibility and adequate electroactivity for further research in biosensing and other surface functionalizing.     

A new interference-free lysine biosensor using a non-conducting polymer film

An electrochemical biosensor for the determination of lysine to be used for rapid evaluation of food quality has been developed. Platinum electrodes have been coated by electropolymerisation with 1,2-diaminobenzene (1.2-DAB) using cyclic voltammetry. The reduction in the oxidation of interferents compared with the bare platinum electrode was 100% for ascorbic acid, 99% for acetaminophen and 99% for cysteine. The enzyme L-lysine--oxidase was then immobilised onto the polymer layer by passive adsorption and a calibration curve for lysine constructed. This gave a linear range of 1×10⁻⁵ mol/l to 1×10⁻³ mol/l and a limit of detection of 2×10⁻⁷ mol/l.     

Fabrication of sucrose biosensor based on single mode planar optical waveguide using co-immobilized plant invertase and GOD

In present studies, the new optical sensing platform based on optical planar waveguide (OPWG) for sucrose estimation was reported. An evanescent-wave biosensor was designed by using novel agarose–guar gum (AG) biopolymer composite sol–gel with entrapped enzymes (acid invertase (INV) and glucose oxidase (GOD)). Partially purified watermelon invertase isolated from Citrullus vulgaris fruit (specific activity 832 units mg⁻¹) in combination with GOD was physically entrapped in AG sol–gel and cladded on the surface of optical planar waveguide. Na⁺–K⁺ ion-exchanged glass optical waveguides were prepared and employed for the fabrication of sucrose biosensor. By addressing the enzyme modified waveguide structure with, the optogeometric properties of adsorbed enzyme layer (12 μm) at the sensor solid–liquid interface were studied. The OPWG sensor with short response time (110 s) was characterized using the 0.2 M acetate buffer, pH 5.5. The fabricated sucrose sensor showed concentration dependent linear response in the range 1 × 10⁻¹⁰ to 1 × 10⁻⁶ M of sucrose. Lower limit of detection of this novel AG–INV–GOD cladded OPWG sensor was found to be 2.5 × 10⁻¹¹ M sucrose, which indicates that the developed biosensor has higher sensitivity towards sucrose as compared to earlier reported sensors using various transducer systems. Biochips when stored at room temperature, showed high stability for 81 days with 80% retention of original sensitivity. These sucrose sensing biochips showed good operational efficiency for 10 cycles. The proper confinement of acid invertase and glucose oxidase in hydrogel composite was confirmed by scanning electron microscopy (SEM) images. The constructed OPWG sensor is versatile, easy to fabricate and can be used for sucrose measurements with very high sensitivity.     

Glutathione-proline activation of feeding behavior in the zoanthid Palythoa psammophilia Walsh & Bowers

Palythoa psammophilia Walsh & Bowers has a well coordinated, stereotyped feeding response, the culminating step of which is ingestion; this may be elicited by the synergistic effect of the tripeptide glutathione and the -imino acid, proline. Either activator acting separately causes responses only at high concentrations (above 10⁻⁵ M for glutathione; above 10⁻⁴ M for proline) in a reduced number of animals and at a low rate (5.00 ± 1.73 min in 5 × 10⁻³ M solutions of glutathione; 11.10±3.74 min in 5 × 10⁻³ M solutions of proline). Highest percentages of response were obtained in combinations where glutathione was at a concentration of 5 × 10⁻³ M and proline at 5 × 10⁻⁴ M or in combinations of glutathione at concentrations 5 × 10⁻⁶ M and proline at 5 × 10⁻⁵ M. The speed of ingestion is considerably enhanced when these activators are combined (1.17±1.18 min).     

Synthesis of graft copolymer (k-carrageenan-g-N,N-dimethylacrylamide) and studies of metal ion uptake, swelling capacity and flocculation properties

Graft copolymer of k-carrageenan and N,N-dimethylacrylamide has been synthesized by free radical polymerization using peroxymonosulphate/glycolic acid redox pair in an inert atmosphere. The grafting parameters i.e. grafting ratio, add on and efficiency decrease with increase in concentration of k-carrageenan from 0.6 to 1.4 g dm⁻³ and hydrogen ion from 3 × 10⁻³ to 7 × 10⁻³ mol dm⁻³, but these grafting parameters increase with increase in concentration of N,N-dimethylacrylamide from 16 × 10⁻² to 32 × 10⁻² mol dm⁻³, and peroxymonosulphate from 0.8 × 10⁻² to 2.4 × 10⁻² mol dm⁻³. The metal ion sorption, swelling behaviour and flocculation properties have been studied. The intrinsic viscosity of pure and grafted samples has been measured by using Ubbelohde capillary viscometer. Flocculation capability of k-carrageenan and k-carrageenan-g-N,N-dimethylacrylamide for both coking and non-coking coals has been studied for the treatment of coal mine waste water. The graft copolymer has been characterized by Infrared (IR) spectroscopy and thermogravimetric analysis.     

Glucose biosensor based on immobilization of glucose oxidase in poly(o-aminophenol) film on polypyrrole-Pt nanocomposite modified glassy carbon electrode

Novel Pt nanoclusters embedded polypyrrole nanowires (PPy-Pt) composite was electrosynthesized on a glassy carbon electrode, denoted as PPy-Pt/GCE. A glucose biosensor was further fabricated based on immobilization of glucose oxidase (GOD) in an electropolymerized non-conducting poly(o-aminophenol) (POAP) film that was deposited on the PPy-Pt/GCE. The morphologies of the PPy nanowires and PPy-Pt nanocomposite were characterized by field emission scanning electron microscope (FE-SEM). Effect of experimental conditions involving the cycle numbers for POAP deposition and Pt nanoclusters deposition, applied potential used in glucose determination, temperature and pH value of the detection solution were investigated for optimization. The biosensor exhibited an excellent current response to glucose over a wide linear range from 1.5 × 10⁻⁶ to 1.3 × 10⁻² M (r = 0.9982) with a detection limit of 4.5 × 10⁻⁷ M (s/n = 3). Based on the combination of permselectivity of the POAP and the PPy films, the sensor had good anti-interference ability to ascorbic acid (AA), uric acid (UA) and acetaminophen. The apparent Michaelis–Menten constant (K_m) and the maximum current density (I_m) were estimated to be 23.9 mM and 378 μA/cm², respectively. In addition, the biosensor had also good sensitivity, stability and reproducibility.     

Graft copolymerization of acrylic acid onto guar gum initiated by vanadium (V)–mercaptosuccinic acid redox pair

Guar gum has been modified by graft copolymerization with acrylic acid in aqueous medium using vanadium (V)–mercaptosuccinic acid redox system. The optimum reaction conditions affording maximum grafting ratio, efficiency, add on and conversion have been determined. The grafting parameters have been found to increase with increase in vanadium (V) concentration upto 1.0 × 10⁻² mol dm⁻³, but these parameters decrease on further increasing the vanadium (V) concentration. On increasing the mercaptosuccinic acid concentration from 1.0 × 10⁻² to 4.0 × 10⁻² mol dm⁻³ grafting ratio, efficiency and add on increase up to 2.0 × 10⁻² mol dm⁻³ but decrease with further increase in mercaptosuccinic acid concentration. On varying the acrylic acid concentration from 5.0 × 10⁻² to 30.0 × 10⁻² mol dm⁻³, maximum grafting ratio, efficiency and add on have been obtained at 20.0 × 10⁻² mol dm⁻³. The grafting ratio, add on and conversion increase, on increasing the H⁺ ion concentration from 1.5 × 10⁻¹ to 6.0 × 10⁻¹ mol dm⁻³. On increasing the guar gum concentration the grafting parameters increase. The grafting ratio, add on and conversion have been found to increase with time period while efficiency started decreasing after 120 min. It has been observed that %G increases on increasing the temperature up to 35 °C. The graft copolymer has been characterized by IR spectroscopy and thermogravimetric analysis.     

Cortisol and testosterone: Inhibitory agents of the mineralocorticoid pathway. Is there a physiopathological meaning in adrenal tumors?

The authors incubated adrenal mitochondria to study the in vitro action of cortisol and testosterone on the transformation of corticosterone and 18-hydroxycorticosterone into aldosterone. The results show that cortisol at concentrations of 5 × 10⁻⁶ and 10⁻⁴ M inhibit the conversion of corticosterone into aldosterone by 23.6 to 90%; testosterone 5 × 10⁻⁵ and 10⁻⁴ M inhibit the reaction by 78.4 and 87.2%, respectively. The inhibition of the conversion of 18-hydroxycorticosterone into aldosterone is 12.5 to 91% by cortisol with concentrations ranging from 5 × 10⁻⁷ to 5 × 10⁻⁵ M and testosterone 5 × 10⁻⁵ and 10⁻⁴ M inhibits the reaction by 87.3 and 91%, respectively. Aldosterone (10⁻⁸ and 10⁻⁶ M) does not inhibit aldosterone biosynthesis from corticosterone or 18-hydroxycorticosterone. It thus appears that cortisol and testosterone have an effect on the aldosterone biosynthesis pathways in mitochondria. This action may be located at the binding site of the cytochrome P450 11β, which catalyzes all hydroxylation steps in the mineralocorticoid biosynthesis pathway. Because cortisol and testosterone may interfere with aldosterone biosynthesis, and since functional zonation is expected in adrenal carcinomas, the presence of these steroids in substantial amounts could explain the very low plasma aldosterone level usually observed, in adrenal carcinomas studies in our laboratory.     

Potassium selective chemically modified field effect transistors based on AlGaN/GaN two-dimensional electron gas heterostructures

We investigate the use of the AlGaN/GaN high electron mobility transistor (HEMT) as a novel transducer for the development of ion-selective chemically modified HEMT sensors (ChemHEMTs). For this, polyvinyl chloride (PVC) membrane doped with ion-selective ionophores is deposited onto the area of the gate for the chemical recognition step, while the AlGaN/GaN HEMT is used as the transducer. In particular, the use of a valinocycin doped membrane with thickness of 50 μm generates a sensor with excellent analytical characteristics for the monitoring of K⁺. The K⁺-ChemHEMT has sensitivity of 52.4 mV/pK⁺in the linear range of 10⁻⁵ to 10⁻² M, while the detection limit is in the order of 3.1 × 10⁻⁶ M. Also, the sensor shows selectivity similar to valinomycin-based ISEs, while the signal stability over time and the measurement to measurement reproducibility are very good.     

Induction of chromosomal aberrations, sister-chromatid exchanges and cell-cycle delay in cow peripheral blood lymphocytes treatment with two N-nitroso compounds in vitro

We investigated the effect of NDMA and DNSGU on the induction of chromosomal aberrations and sister-chromatid exchanges (SCEs), as well as the influence of the former compound on cell-cycle kinetics in cultured cow peripheral lymphocytes. A clastogenic effect was observed in treated cell cultures at 6 or 12 × 10⁻⁵ M concentrations of NDMA and DNSGU, respectively, but no increase of chromosomal breaks was seen at the lowest dose. NDMA at 6 × 10⁻⁴ M was toxic to cow lymphocytes. NDMA and DNSGU induced statistical increases of SCEs at the test doses (6 or 12 × 10⁻⁶ and 6 or 12 × 10⁻⁵ M, respectively). In addition, treatment with NDMA at a dose of 6 × 10⁻⁵ M revealed significant heterogeneity of the first, second and third metaphases between treated and untreated groups. A reduction of the proliferation index and proliferation delay per cycle was shown too.     

Nitric oxide stimulates prostaglandin synthesis in cultured rabbit gastric cells

Both prostaglandins (PGs) and nitric oxide (NO) have cytoprotective and hyperemic effects in the stomach. However, the effect of NO on PG synthesis in gastric mucosal cells is unclear. We examined whether sodium nitroprusside (SNP), a releaser of NO, stimulates PG synthesis in cultured rabbit gastric mucus-producing cells. These cells did not release NO themselves. Co-incubation with SNP (2 × 10⁻⁴, 5 × 10⁻⁴, 10⁻³ M) increased PGE₂ synthesis, and SNP (10⁻³ M) increased PGI₂ synthesis in these cells. Hemoglobin, a scavenger of NO, (10⁻⁵ M) eliminated the increase in PGE₂ synthesis by SNP, but methylene blue, an inhibitor of soluble guanylate cyclase, (5 × 10⁻⁵ M) did not affect the increase in PGE₂ synthesis by SNP. 8-bromo guanosine 3′ : 5′-cyclic monophosphate (8-bromo cGMP), a cGMP analogue, (10⁻⁶, 10⁻⁵, 10⁻⁴, 10⁻³ M) did not affect PGE₂ synthesis. These findings suggest that NO increased PGE₂ and PGI₂ synthesis via a cGMP-independent pathway in cultured rabbit gastric cells.     

Chromosome aberrations in workers of nuclear-power plants

The frequencies of chromosome aberrations in 135 workers from nuclear-power plants were compared with those in 135 age-matched controls. A total of 135,000 cells was scored. The frequencies of dicentric chromosome were 1.67 × 10⁻³ in the exposed group and 0.49 × 10⁻³ in the control group and those of chromosome-type deletion were 3.33 × 10⁻³ and 1.10 × 10⁻³, respectively. The frequencies of all types of chromosome aberrations in the exposed subjects were higher than those in the control group, but no significant trend of dose-dependent increase was observed when only the exposed group were considered. Poisson regression analysis, with both exposed and control included, showed that there was a significant association of chromosome aberration with radiation dose and the duration of work, but not with age, smoking habit and alcohol intake. It was also found that recent exposure to radiation, within the last 5 years, had contributed more to the observed chromosome aberration than earlier exposure.     

Determination of digoxin in serum samples using a flow-through fluorosensor based on a molecularly imprinted polymer

This work describes the development of a competitive flow-through FIA assay for digoxin using a molecularly imprinted polymer (MIP) as the recognition phase. In previous work, a number of non-covalent imprinted polymers were synthesised by “bulk” polymerisation. The digoxin binding and elution characteristics of these MIPs were then evaluated to obtain a highly selective material for integration into a sensor. The optimum MIP was synthesised by photo-initiated polymerisation of a mixture containing digoxin, MAA, EDGMA and AIBN in acetonitrile. The bulk polymer was ground and sieved and the template removed by Soxhlet extraction in MeOH/ACN. The MIP was packed into a flow cell and placed in a spectrofluorimeter to integrate the reaction and detection systems. The physical and chemical variables involved in digoxin determination by the sensor (nature and concentration of solution, flow rates, etc.) were optimised. Binding with the non-imprinted polymer (NIP) was also analysed. The new fluorosensor showed high selectivity and sensitivity, a detection limit of 1.7 × 10⁻² μg l⁻¹, and high reproducibility (R.S.D. of 1.03% and 1.77% for concentrations of 1.0 × 10⁻³ and 4.0 × 10⁻³ mg l⁻¹, respectively). Selectivity was tested by determining the cross-reactivity of several compounds with structures analogous to digoxin. Under the assay conditions used, in which the potential interfering compounds were in concentrations 100 times higher than that of the analyte, no interference was recorded. The proposed fluorosensor was successfully used to determine digoxin concentration of human serum samples.     

Displacement of [H]GABA binding to bovine brain receptors by sulfur-containing analogues

The displacement of [³H]GABA binding to GABA receptors of bovine brain cortical membranes by some sulfur-containing compounds (homothiotaurine, thiotaurine and carboxymethylcysteamine) was investigated and their potency was compared to that of other known sulfur-containing analogues of GABA, such as homotaurine, homohypotaurine and taurine. Displacement studies showed homotaurine to be more effective as a GABA displacer than homohypotaurine and homothiotaurine (IC₅₀: 3.9 × 10⁻⁸, 6.7 × 10⁻⁷ and 6.8 × 10⁻⁷ M, respectively). Saturation experiments showed that the effect of taurine, homothiotaurine, homotaurine and homohypotaurine was due to a loss of high-affinity GABA sites (K_d = 10.7 nM). Homotaurine seems also to interact with low-affinity sites, decreasing the affinity constant, whereas the number of binding sites remains unchanged.     

Optimizing the formulation of a myoglobin molecularly imprinted thin-film polymer--formed using a micro-contact imprinting method

Thin-film myoglobin molecularly imprinted polymers have been fabricated using a micro-contact approach. By initially selecting the cross-linker on the basis of it having a minimal recognition for the template and using this as a starting point for functional monomer selection, we have produced myoglobin imprinted polymers with exceptionally high selectivities.

The affinity of the polymers, for myoglobin, when prepared with a variety of different cross-linkers and no functional monomer was evaluated. Of these, tetraethylene glycol dimethacrylate (TEGDMA) exhibited the lowest affinity for the template species. Methyl methacrylate (MMA) was chosen as the functional monomer as when it was used in conjunction with TEGDMA, it exhibited maximum selectivity for the template compared to polymers made with other functional monomers.

With a MMA to TEGDMA ratio of 1 to 3, the myoglobin molecularly imprinted polymer adsorbed 15.03 ± 0.89 × 10⁻¹¹ mole/cm² of template from a 5.68 × 10⁻⁷ M myoglobin solution, compared to 2.58 ± 0.02 × 10⁻¹¹ mole/cm² for a polymer of similar composition, but formed in the absence of a template. Various washing conditions, using alkaline media to remove the template, were investigated. An extraction solvent comprising 2 wt.% SDS and 0.6 wt.% NaOH used at 80 °C for 30 min was shown to give the highest imprinting factor i.e. 5.83 with 72.82% myoglobin removal.

The saturation kinetics of template binding to the thin-film MIP were examined and found to display a simple two-phase profile typical of non-cooperative binding. A Scatchard binding plot showed the dissociation constant (K_d) for the specific binding phase to be 3.4 × 10⁻⁷ M and the binding site capacity to be 7.24 × 10⁻¹¹ mole/cm². For the non-specific binding phase, K_d was found to be 1.355 × 10⁻⁵ M and the binding site capacity was determined as 9.62 × 10⁻¹⁰ mole/cm².

Selectivity experiments were carried out in both single protein and binary protein systems all using a total protein concentration of 5.68 × 10⁻⁷ M. The molar ratio of adsorbed myoglobin to IgG, HSA and hemoglobin was found to 115.5, 230.9 and 2.5, respectively. While, in binary competition systems, myoglobin selectivity to IgG, HSA and hemoglobin was, respectively, 94.18, 98.21 and 61.09%. Rebinding in natural biological matrices, i.e. human serum or urine, showed the imprinted films to have significantly greater uptake than non-imprinted films. Re-binding in undiluted urine was found to be a facile process, with the imprinting factor, i.e. the ratio of MIP to NIP binding, being determined as 37.4.