High density cultivation of Anchusa officinalis in a stirred-tank bioreactor with in situ filtration

Previously, Su et al. [Biotechnol Bioeng 42: 884–890 (1993)] reported improved production of rosmarinic acid by Anchusa officinalis in shake-flask cultures using a cultivation strategy that involved intermittent medium exchange. Implementation of this cultivation strategy in 2.5-1 stirred-tank bioreactor cultures is investigated in the present study. Intermittent cell/medium separation in the bioreactor was accomplished by means of automated in situ culture filtration. In the bioreactor culture, rosmarinic acid production was found very sensitive to agitation and aeration conditions as well as dissolved oxygen concentration. A maximum cell density of 35 g dry weight/l and a rosmarinic acid concentration of 3.7 g/l were obtained by maintaining the dissolved oxygen concentration above 30% air saturation, gradually raising the impeller tip speed from 34 cm/s to 72 cm/s, and keeping the aeration rate at 0.44 vvm while increasing the O₂: air ratio in the gas feed stream to 4:1. This result is comparable with the data obtained from shake-flask cultures using the same culture strategy.     

Optimization of the production of progesterone 11α-hydroxylase by Rhizopus nigricans

The progesterone 11α-hydroxylase of Rhizopus nigricans ATCC 6227b is an inducible enzyme system that is primarily induced by its substrate progesterone. Maximum induction was found at a progesterone concentration of 0.5 g/liter or above. Oxygen is the other substrate for the hydroxylation and this was found to have a major effect on the amounts of hydroxylase synthesized. Optimum induction of the hydroxylase in a fermentation with a 3.1 m/sec impeller tip speed was found to occur at a dissolved oxygen tension (DOT) of 10% of air saturation. The agitation rate also effects the amount of hydroxylase synthesized with an apparent maximum at 3.1 m/sec impeller tip speed. The DOT for a maximum hydroxylation rate was much higher than for enzyme synthesis so that it was preferable to increase the DOT after induction was completed.     

Enhancement of glucose oxidase production in batch cultivation of recombinant Saccharomyces cerevisiae: optimization of oxygen transfer condition

AIMS: To obtain an optimal combination of agitation speed and aeration rate for maximization of specific glucose oxidase (GOD) production in recombinant Saccharomyces cerevisiae, and to establish a correlation between kLa vis-à-vis oxygen transfer condition and specific glucose oxidase production. METHODS AND RESULTS: The oxygen transfer condition was manifested indirectly by manipulating the impeller speed and aeration rate in accordance with a Central Composite Rotatory Design (CCRD). The dissolved oxygen concentration and the volumetric oxygen transfer coefficient (kLa) were determined at corresponding combinations of impeller speed and aeration rate. The maximal specific extracellular glucose oxidase production (3.17 U mg-1 dry cell mass) was achieved when the initial dissolved oxygen concentration was 6.83 mg l-1 at the impeller speed of 420 rev min-1 and at the rate of aeration of 0.25 vvm. It was found out that while impeller speed had a direct effect on the production of enzyme, a correlation between kLa and specific GOD production could not be established. CONCLUSION: At the agitation speed of 420 rev min-1 and at 0.25 vvm aeration rate, the degree of turbulence and the dissolved oxygen concentration were thought to be optimal both for cellular growth and production of enzyme. SIGNIFICANCE AND IMPACT OF THE STUDY: The combined effect of agitation and aeration on recombinant glucose oxidase production in batch cultivation has not yet been reported in the literature. Therefore, this study gives an insight into the effect of these two important physical parameters on recombinant protein production. It also suggests that since there is no correlation between kLa and specific production of GOD, kLa should not be used as one of the scale-up parameters.     

The role of aeration and agitation in the production of glucose oxidase in submerged culture. II

The main purpose of the work reported here was to establish the effectiveness of aeration and agitation, and to determine the best conditions of aeration for the growth and production of glucose oxidase of Aspergillus niger, on a semi-industrial scale. Concentration of dissolved O₂, O₂ consumption and CO₂ production were measured. It was found that the rate of growth and the activity of glucose oxidase per gram mycelium increased with the increase of speed of agitation. The concentration of dissolved oxygen of the fermentation broth, as well as the rate of respiration (O₂ consumption and CO₂ production) increased in direct proportion to the increase of speed of agitation, while assimilation of sugars was accelerated. The values of the respiratory ratio showed a fluctuation according to the presence or absence of sugar in the medium.     

Application of Oxygen-Enriched Aeration in the Conversion of Glycerol to Dihydroxyacetone by Gluconobacter melanogenus IFO 3293

Gluconobacter melanogenus 3293 converts glycerol to dihydroxyacetone(DHA) during exponential growth on a yeast extract-phosphate medium at pH 7. The efficiency of this conversion in 25-liter batch fermentations has been found to increase over threefold, when oxygen tension is controlled by increasing the partial pressure of oxygen in the aeration. Conversion of glycerol to DHA does not occur under oxygen-limited fermentation conditions. When the dissolved oxygen tension was maintained at 0.05 atmospheres (using oxygen-enriched air), quantitative conversion of up to 100 g of glycerol/liter to DHA was obtained in 33 h. The amount of glycerol converted can be increased without increasing impeller speed or aeration rate. This increase is not the result of increased production of cell mass. The specific conversion of glycerol to DHA increased from 12.2 g of DHA/g of cell mass at the point of maximum conversion to 35.8 with oxygen enrichment. This increased specific production occurred even though the specific growth rate during the period of oxygen enrichment decreased from 0.23 to 0.06/h.     

Continuous itaconic acid production by immobilized biocatalysts.

The continuous itaconic acid production from sucrose with Aspergillus terreus TKK 200-5-3 mycelium immobilized on polyurethane foam cubes was optimized in column bioreactors using statistical experimental design and empirical modelling. The highest itaconic acid product concentration calculated on the basis of the obtained model was 15.8 g l-1 in the investigated experimental area, when sucrose concentration was 13.5%, aeration rate 150 ml min-1 and residence time 178 h. From sucrose with immobilized A. terreus TKK 200-5-3 mycelium itaconic acid production was stable for at least 4.5 months in continuous column bioreactors. In comparison, using glucose as substrate and immobilized A. terreus TKK 200-5-1 mycelium as biocatalyst similar stability was obtained with higher product concentration. The omission of copper sulphate from the production medium gave the highest itaconic acid product concentration (26 g l-1) from 9% glucose with 0.25% ammonium nitrate and 0.095% magnesium sulphate.     

Itaconic acid production by immobilizedAspergillus terreus on sucrose medium

Summary The itaconic acid production by immobilizedAspergillus terreus TTK 200-5-3 mycelium was optimized in shake flask fermentations using statistical experimental design and empirical modelling. The maximum itaconic acid concentration was calculated to be 13.3 g/l in the investigated experimental area when initial sucrose concentration was 10%, ammonium nitrate concentration 0.275% and initial pH 3. The itaconic acid product concentration using immobilized mycelium was about double of that obtained with the free mycelium.     

Production of rosmarinic acid by<Emphasis Type="Italic">Lavandula vera</Emphasis> MM cell suspension in bioreactor: effect of dissolved oxygen concentration and agitation

The relationship between dissolved oxygen (DO) concentration, agitation rate and growth of Lavandula vera MM and rosmarinic acid biosynthesis was investigated in 3 l laboratory bioreactor. Lavandula vera MM cell suspension accumulated the highest amounts of biomass (34.8 g/l) and rosmarinic acid (1870.6 mg/l) on day 12 of cultivation at 50% dissolved oxygen and agitation speed 100 rpm and at 30% dissolved oxygen and agitation speed 300 rpm, respectively.     

Production and scale‐up of a monoclonal antibody against 17‐hydroxyprogesterone

The hybridoma 192 was used to produce a monoclonal antibody (MAb) against 17‐hydroxyprogesterone (17‐OHP), for possible use in screening for congenital adrenal hyperplasia (CAH). The factors influencing the MAb production were screened and optimized in a 2 L stirred bioreactor. The production was then scaled up to a 20 L bioreactor. All of the screened factors (aeration rate, stirring speed, dissolved oxygen concentration, pH, and temperature) were found to significantly affect production. Optimization using the response surface methodology identified the following optimal production conditions: 36.8°C, pH 7.4, stirring speed of 100 rpm, 30% dissolved oxygen concentration, and an aeration rate of 0.09 vvm. Under these conditions, the maximum viable cell density achieved was 1.34 ± 0.21 × 10⁶ cells mL^?1 and the specific growth rate was 0.036 ± 0.004 h^?1. The maximum MAb titer was 11.94 ± 4.81 μg mL^?1 with an average specific MAb production rate of 0.273 ± 0.135 pg cell^?1 h^?1. A constant impeller tip speed criterion was used for the scale‐up. The specific growth rate (0.040 h^?1) and the maximum viable cell density (1.89 × 10⁶ cells mL^?1) at the larger scale were better than the values achieved at the small scale, but the MAb titer in the 20 L bioreactor was 18% lower than in the smaller bioreactor. A change in the culture environment from the static conditions of a T‐flask to the stirred bioreactor culture did not affect the specificity of the MAb toward its antigen (17‐OHP) and did not compromise the structural integrity of the MAb. © 2012 American Institute of Chemical Engineers Biotechnol. Prog., 2013     

Dependence of penicillium chrysogenum growth, morphology, vacuolation, and productivity in fed-batch fermentations on impeller type and agitation intensity

The influence of the agitation conditions on the growth, morphology, vacuolation, and productivity of Penicillium chrysogenum has been examined in 6 L fed-batch fermentations. A standard Rushton turbine, a four-bladed paddle, and a six-bladed pitched blade impeller were compared. Power inputs per unit volume of liquid, P/VL, ranged from 0.35 to 7.4 kW/m3. The same fermentation protocol was used in each fermentation, including holding the dissolved oxygen concentration above 40% air saturation by gas blending. The mean projected area (for all dispersed types, including clumps) and the clump roughness were used to characterize the morphology. Consideration of clumps was vital as these were the predominant morphological form. For a given impeller, the batch-phase specific growth rates and the overall biomass concentrations increased with agitation intensity. Higher fragmentation at higher speeds was assumed to have promoted growth through increased formation of new growing tips. The mean projected area increased during the rapid growth phase followed by a sharp decrease to a relatively constant value dependent on the agitation conditions. The higher the speed, the lower the projected area for a given impeller type. The proportion by volume of hyphal vacuoles and empty regions decreased with speed, possibly due to fragmentation in the vacuolated regions. The specific penicillin production rate was generally higher with lower impeller speed for a given impeller type. The highest value of penicillin production as well as its rate was obtained using the Rushton turbine impeller at the lowest speed. At given P/VL, changes in morphology, specific growth rate, and specific penicillin production rate depended on impeller geometry. The morphological data could be correlated with either tip speed or the "energy dissipation/circulation function," but a reasonable correlation of the specific growth rate and specific production rate was only possible with the latter. Copyright 1998 John Wiley & Sons, Inc.     

Synthesis of staphylococcal enterotoxin A and nuclease under controlled fermentor conditions.

The production of enterotoxin A and nuclease by Staphylococcus aureus strain 100 was studied in a 1.0-liter fermentor. The effects of the gas flow rate, pH, and dissolved oxygen were evaluated. Toxin and nuclease secretion occurred under all conditions which permitted growth of the organism. Final yields of toxin and nuclease in cultures grown at constant air flow rates, ranging from 50 to 500 cm3 per min, were higher at successively higher flow rates. An optimum flow rate for either toxin or nuclease production was not observed. When the aeration rate alone or aeration rate and pH were held constant, the dissolved oxygen levels in the culture decreased from the initial 100% level to 0 to 5% 3 to 4 h after inoculation. The O2 demand of the culture then maintained this level for an additional 4 to 5 h. This low dissolved oxygen interval was characterized by rapid growth and extracellular protein production. Controlling the dissolved oxygen at a constant level throughout growth did not increase the final levels of toxin and nuclease above those achieved at the respective constant pH values. Growth under the influence of a constant aeration rate of 500 cm3 per min and a constant pH of 6.5 and 7.0 yielded the highest titers of nuclease (1,550 units/ml) and toxin (10.5 mug/ml) obtained in any of the fermentations conducted in this study. Sparging fermentor cultures with pure oxygen at a rate of 100 cm3 per min yielded growth and extracellular protein levels similar to those achieved at the sparge rate of 500 cm3 of air per min. Controlling the dissolved oxygen at 100% of pure oxygen saturation appeared to inhibit the culture, as the final cultural turbidity as well as the levels of toxin and nuclease were reduced. These data indicate that enterotoxin and nuclease secretions are closely associated with the growth of strain 100. Analyses of the production rates of these components indicated that early log phase was the most efficient production interval in the growth cycle and that this efficiency was increased by pH control at 6.7 to 6.8 and dissolved oxygen control at 10% of air saturation.     

Synthesis of staphylococcal enterotoxin A and nuclease under controlled fermentor conditions.

The production of enterotoxin A and nuclease by Staphylococcus aureus strain 100 was studied in a 1.0-liter fermentor. The effects of the gas flow rate, pH, and dissolved oxygen were evaluated. Toxin and nuclease secretion occurred under all conditions which permitted growth of the organism. Final yields of toxin and nuclease in cultures grown at constant air flow rates, ranging from 50 to 500 cm3 per min, were higher at successively higher flow rates. An optimum flow rate for either toxin or nuclease production was not observed. When the aeration rate alone or aeration rate and pH were held constant, the dissolved oxygen levels in the culture decreased from the initial 100% level to 0 to 5% 3 to 4 h after inoculation. The O2 demand of the culture then maintained this level for an additional 4 to 5 h. This low dissolved oxygen interval was characterized by rapid growth and extracellular protein production. Controlling the dissolved oxygen at a constant level throughout growth did not increase the final levels of toxin and nuclease above those achieved at the respective constant pH values. Growth under the influence of a constant aeration rate of 500 cm3 per min and a constant pH of 6.5 and 7.0 yielded the highest titers of nuclease (1,550 units/ml) and toxin (10.5 mug/ml) obtained in any of the fermentations conducted in this study. Sparging fermentor cultures with pure oxygen at a rate of 100 cm3 per min yielded growth and extracellular protein levels similar to those achieved at the sparge rate of 500 cm3 of air per min. Controlling the dissolved oxygen at 100% of pure oxygen saturation appeared to inhibit the culture, as the final cultural turbidity as well as the levels of toxin and nuclease were reduced. These data indicate that enterotoxin and nuclease secretions are closely associated with the growth of strain 100. Analyses of the production rates of these components indicated that early log phase was the most efficient production interval in the growth cycle and that this efficiency was increased by pH control at 6.7 to 6.8 and dissolved oxygen control at 10% of air saturation.     

Influence of dissolved oxygen and shear conditions on clavulanic acid production by Streptomyces clavuligerus

Clavulanic acid (CA), a potent β-lactamase inhibitor, is produced by a filamentous bacterium. Here, the effect of DO and shear, expressed as impeller tip velocity, on CA production was examined. Cultivations were performed in a 4 L fermentor with speeds of 600, 800 and 1,000 rpm and a fixed air flow rate (0.5 vvm). Also, cultivation with automatic control of dissolved oxygen, at 50% air saturation, by varying stirrer speed and using a mixture of air and O₂ (10% v/v) in the inlet gas, and a cultivation with fixed stirrer speed of 800 rpm and air flow rate of 0.5 vvm, enriched with 10% v/v O₂, were performed. Significant variations in CA titer, CA production rate and O₂ uptake-rate were observed. It was also found that the DO level has no remarkable effect on CA production once a critical level is surpassed. The most significant improvement in CA production was related to high stirrer speeds.     

Factors Influencing the Production of a Novel Compound, 7,10-Dihydroxy-8(<Emphasis Type="Italic">E</Emphasis>)-octadecenoic Acid,by <Emphasis Type="Italic">Pseudomonas aeruginosa</Emphasis> PR3 (NRRL B-18602) in Batch Cultures

Pseudomonas aeruginosa PR3 (NRRL B-18602) converts oleic acid to a novel compound, 7,10-dihydroxy-8(E)-octadecenoic acid (DOD). Parameters that included medium volume, cell growth time, gyration speed, pH, substrate concentration, and dissolved oxygen concentration were evaluated for a scale-up production of DOD in batch cultures using Fernbach flasks and a bench-top bioreactor. Maximum production of about 2 g DOD (38% yield) was attained in Fernbach flasks containing 500 ml medium when cells were grown at 28°C and 300 rpm for 16–20 h and the culture was adjusted to pH 7 prior to substrate addition. Increases of medium volume and substrate concentration failed to enhance yield. When batch cultures were initially conducted in a reactor, excessive foaming occurred that made the bioconversion process inoperable. This was overcome by a new aeration mechanism that provided adequate dissolved oxygen to the fermentation culture. Under the optimal conditions of 650 rpm, 28°C, and 40–60% dissolved oxygen concentration, DOD production reached about 40 g (40% yield) in 4.5 L culture medium using a 7-L reactor vessel. This is the first report on a successful scale-up production of DOD. Received: 26 September 2002 / Accepted: 24 October 2002     

Reactor properties of a high-speed bead mill for microbial cell rupture

Laboratory and pilot-plant high-speed bead mills of 0.6 and 5 liter capacity and consisting of four and five impellers in series, respectively, were used to follow the batch and continuous disruption of bakers' yeast (Saccharomyces cerevisiae). The mills are not scaled equivalents. Throughputs ranging from 1 × 10^?6m³/sec to 12 × 10^?6m³/sec for the 0.6 liter mill and from 16 × 10^?6m³/sec to 100 × 10^?6m³/sec for the 5 liter mill were used for continuous disruption studies. Variables studied included the effect of impeller tip speed, temperature, and packed yeast concentration (ranging from 15 to75% by weight packed yeast). Disruption kinetics, as measured by the release of soluble protein, followed a first-order rate equation, the rate constant being a function of impeller tip speed and yeast concentration. For continuous disruption studies the bead mills behaved as a series of continuous stirred-tank reactors, each impeller forming a reactor. In the smaller mill a considerable degree of backflow between the reactors was evident. For certain mixing conditions the maximum amount of releasable protein was dependent on the impeller geometry, construction material, and also the concentration of packed yeast. The relative power efficiencies of the two mills are discussed along with possible criteria for scaling of bead mills.     

Influence of pH and impeller tip speed on the cultivation of<Emphasis Type="Italic">Bifidobacterium pseudocatenulatum</Emphasis> G4 in a milk-based medium

Biomass production ofBifidobacterium pseudocatenulatum G4 in a milk-based medium was carried out in a 2- and 10-L stirred tank fermenters. The effects of impeller tip speed (0.28, 0.56, and 0.83 m/s) and pH control (6.0, 6.5, and 7.0) on the biomass production were investigated. The growth performance in the 2-L fermenter was significantly improved when the impeller tip speed was held constant at 0.56 m/s and the pH was controlled at 6.5. These conditions yielded a maximum biomass of 1.687×10⁹ cfu/mL, a maximum specific growth rate of 0.504 h⁻¹, a biomass productivity of 9.240×10⁷ cfu/mL·h, and a biomass yield of 9.791×10¹⁰ cfu/g lactose. The consumption of milk lactose resulted in the accumulation of 7.353 g/L acetic acid and 6.515 g/L lactic acid, with an acetic:lactic ratio of 1.129. Scale-up of the fermentation process to a 10-L fermenter based on a constant impeller tip speed of 0.56 m/s yielded reproducible results with respect to biomass production and cell viability.     

Itaconic acid production from xylose in repeated-batch and continuous bioreactors

Summary Itaconic acid production from xylose by immobilized Aspergillus terreus TKK 200-5-2 mycelia was optimized both in repeated shake-flask fermentations and in continuous column bioreactors using statistical experimental design and empirical modelling. Using continuous 9-1 scale air-lift bioreactors, a pH of 2.5, aeration rate of 0.6 v/v per minute and residence time of 160 h gave the highest itaconic acid concentration. In air-lift bioreactors a cubic carrier size of 0.5 cm gave a 3.3-fold higher product concentration than 1-cm cubes. Packed-bed column reactors had a higher production rate than air-lift reactors. Offprint requests to: H. Kautola     

Influence of hyperbaric oxygen tension on growth parameters of Candida tropicalis and Rhodococcus erythropolis

Summary Oxygen-limited growth was avoided by means of oxygen-enriched aeration in aerobic fermentation processes. Studies were carried out with Candida tropicalis (Cast.) Berkhout and Rhodococcus erythropolis (DSM 43215). The effect of hyperbaric dissolved oxygen tension on growth parameters was examined by varying the dissolved oxygen concentration and the carbon source (glucose, ethanol, and n-alkanes). Up to an oxygen concentration of 40 mg/l in the culture suspension no impairment of the economic coefficients and no promotion of cell lysis was found. It was observed that raised oxygen concentrations in the aeration gas led to enhanced specific growth rates. At cell concentrations above 20 g/l dry weight an uncoupling of carbon source dissimilation and biomass production was observed even at non-limiting oxygen concentrations.     

The effect of Eh on regulatory processes in facultative anaerobes

On increasing aeration rate in chemostat cultures of E. coli the redox potential (E_h) of the culture changes from ?l50 mv to +250 mv. During this period only a slight increase in measured dissolved oxygen concentration is observed. It is suggested that E_h be used as a control variable for aeration in the oxygen limited growth condition, whilst dissolved oxygen concentration be used as control variable in the presence of excess oxygen. Change in cytochrome b₁, three tricarboxylic acid cycle enzymes and hydrogenase can be related to culture E_h. These changes are discussed.