Effect of pre-processing methods on bond strength between acrylic resin teeth and acrylic denture base resin

doi: 10.1111/j.1741‐2358.2011.00480.x
Effect of pre‐processing methods on bond strength between acrylic resin teeth and acrylic denture base resin Objectives: This study evaluated the effects of various pre‐processing methods on the bond strength between resin and denture teeth. Backgrounds: Debonding of acrylic resin teeth from denture base material is a problem for patients wearing complete dentures. Materials and Methods: Four experimental groups (n = 30) were investigated by subjecting tooth–resin bonding to tensile loading. Specimens were prepared and tested according to the methods of the International Standards Organization (ISO 22112:2005) using a special assembly. Four pre‐processing surface treatments of teeth were applied: (i) ST₁, no treatment applied (control); (ii) ST₂, wax solvent (Dewaks, Faber Kimya & Ilaç, Turkey); (iii) ST₃, boiling water followed by conditioning with methyl methacrylate (MMA) monomer (Meliodent, Bayer Dental, Germany); (iv) ST₄, boiling water followed by wax solvent agent and finally MMA monomer application. Bond strength test was performed using a universal testing machine. Results: All the strength values of the test groups were within clinically acceptable limits. The lowest values were from the ST₁ group and the highest values were in the ST₄ group. Conclusions: Wax elimination methods affected bonding strength. Application of wax solvent and MMA monomer to the ridge lap surfaces of the teeth gave the best results. In clinical practice, this application procedure may decrease the bonding failure of denture teeth.     

Bond strength of denture teeth to acrylic resin: effect of thermocycling and polymerisation methods

Background: Failure of bonding between acrylic resin teeth and denture base material is a considerable problem for patients who wear complete dentures. Objective: The purpose of this study was to evaluate the bond strength between acrylic resins and resin denture teeth with different thermocycling and polymerisation methods. Materials and methods: Microwave‐polymerised (Onda‐Cryl), heat‐polymerised (Clássico) and autopolymerising (Jet) acrylic resins and resin denture tooth (Biotone) were used. The acrylic resins were polymerised according to the following: (A) microwave – fast cycle, Onda‐Cryl; (B) microwave – long cycle, Onda‐Cryl; (C) microwave – manufacturer’s cycle, Onda‐Cryl; (T) water bath – long cycle, Clássico; and (Q) bench polymerisation cycle, Jet. Twenty specimens were prepared for each polymerisation method. Ten were thermocycled, and 10 did not receive thermocycling. For the purpose of the study, a shear test was used. Data were analysed with the Kruskal–Wallis test and Dunn’s multiple comparisons test (p = 0.05). Results: Cycles B, C and T were similar (p > 0.05), and had statistically higher bonding values than cycles A and Q (p < 0.05) for the thermocycled and non‐thermocycled groups. For all cycles, there were no statistically significant differences between thermocycled and non‐thermocycled groups (p > 0.05), except for cycle Q (p = 0.0038). Conclusion: Thermocycling decreased the bond strength, but not significantly for microwave and heat‐polymerised cycles. Regarding the bond strength of denture teeth to acrylic resin, the fast microwave polymerisation cycle should be avoided when polymerising Onda‐Cryl acrylic resin. In addition, Jet acrylic resin is not adequate for use in denture repair.     

The effect of long‐term disinfection procedures on hardness property of resin denture teeth

doi: 10.1111/j.1741‐2358.2011.00520.x The effect of long‐term disinfection procedures on hardness property of resin denture teeth Objective: The aim of the study was to evaluate the effect of long‐term disinfection procedures on the Vickers hardness (VHN) of acrylic resin denture teeth. Material and methods: Five acrylic resin denture teeth (Vipi Dent Plus‐V, Trilux–T, Biolux‐B, Postaris‐P and Artiplus‐A) and one composite resin denture teeth (SR‐Orthosit‐O) were embedded in heat‐polymerised acrylic resin within polyvinylchloride tubes. Specimens were stored in distilled water at 37°C for 48 h. Measurements of hardness were taken after the following disinfection procedures: immersion for 7 days in 4% chlorhexidine gluconate or in 1% sodium hypochlorite (CIm and HIm group, respectively) and seven daily cycles of microwave sterilisation at 650 W for 6 min (MwS group). In the WIm group, specimens were maintained in water during the time used to perform the disinfection procedures (7 days). Data were analysed with anova followed by the Bonferroni procedure (α = 0.01). Results: Microwave disinfection decreased the hardness of all acrylic resin denture teeth (p < 0.001). Immersion for 7 days in 4% chlorhexidine gluconate or distilled water had significant effect on the hardness of the acrylic resin denture teeth A (p < 0.01), and 1% sodium hypochlorite on teeth T (p < 0.01). All disinfection procedures decrease the hardness of the composite resin denture teeth (p < 0.01). Teeth O exhibited the highest and teeth V the lowest hardness values in the control group (p < 0.01). Conclusions: Disinfection procedures changed the hardness of resin denture teeth.     

Antifungal and physical characteristics of modified denture base acrylic incorporated with silver nanoparticles

doi: 10.1111/j.1741‐2358.2011.00489.x Antifungal and physical characteristics of modified denture base acrylic incorporated with silver nanoparticles Objective: This study evaluated the antifungal and physical characteristics of denture base acrylic combined with silver nanoparticles. Materials and methods: Polymerized denture acrylic disc specimens containing 0 (control), 1.0, 5.0, 10.0, 20.0 and 30.0 wt% of silver nanoparticles were placed on separate culture plate dish and 100 ìL samples of yeast suspension of Candida albicans strain were inoculated on each specimens and incubated at 37°C, for 24 h. The antifungal effects were evaluated as a number of viable cells in retrieved fungal suspension. To characterize physical aspects, specimens were tested for elution of silver cation (Ag⁺) at 24 h and 30th day, thermal analysis (TG/DTA), scanning electron microscope and energy dispersed X‐ray analysis (SEM/EDX) and color stability. Results: Significant reduced CFU was exhibited at 20.0 and 30.0 wt% of silver nanoparticles incorporated (p < 0.01) and Ag⁺ elution from specimens (maximum 0.356 ± 0.11 mg/L) contributed little to the antifungal activity considering MIC of Ag⁺ in this study (3.0 mg/L). The successful synthesis of modified denture acrylic containing silver nanoparticles was accessed by TG/DTA and EDX analysis. Conclusion: The modified denture base acrylic combined with silver nanoparticles displayed antifungal properties and acted like latent antifungal material itself with low‐releasing Ag⁺, however, the improvement of poor color stability was still required.     

Glass fibre reinforced acrylic resin complete dentures: a 5-year clinical study

doi: 10.1111/j.1741‐2358.2010.00385.x Glass fibre reinforced acrylic resin complete dentures: a 5‐year clinical study Background and objectives: The aim of the study was to establish the wear resistance of the glass fiber reinforced complete dentures comparative to the traditional acrylic complete dentures. Materials and methods: Complete new dentures were made to replace old fractured ‘un’‐reinforced acrylic dentures. The total number of dentures was 30 and woven E‐glass fibre reinforcements were used in maxillary complete dentures. Unidirectional E‐glass fibre reinforcements were used as partial fibre reinforcements in mandibular complete dentures. Ten complete acrylic un‐reinforced dentures were used as control. The follow‐up period was 5 years and the recalls were made at 6 months. Results: After 5 years of wearing the new dentures, the control dentures suffered seven fractures. After 5 years all the mandibular reinforced dentures were in good shape. The maxillary complete reinforced dentures suffered four partial fractures. Fracture lines were restricted by the glass fibre net and the patients could still use their dentures. Conclusion: Pre‐impregnated E‐glass fibre nets and polymer pre‐impregnated E‐glass unidirectional fibres are useful in reinforcing acrylic resin complete dentures especially were heavy occlusal forces are involved. Glass fibre reinforcement will be applied on the tension side in both cases (total fibre reinforcement and partial fibre reinforcement). The reinforcement cannot replace the necessary linings and occlusal adjustments.     

Fatigue resistance of acrylic resin denture base material reinforced with E-glass fibres

doi: 10.1111/j.1741‐2358.2011.00548.x
Fatigue resistance of acrylic resin denture base material reinforced with E‐glass fibres Objective: The purpose of the study was to determine the effect of different forms and concentrations (2.5, 3, 4, 5% by volume) of glass fibres (chopped strand mat, continuous and woven) on fatigue resistance of acrylic denture base resin. Material and Methods: The fatigue resistance was measured by applying repeated three‐point bending deflection to the specimens, the cycle frequency of 1.05 g and magnitude of deflection of 2.0 mm. The number of loading cycles needed to cause a fracture in the test specimen was considered the fatigue resistance of the specimen. Results: The results of this study revealed that the addition of three different glass fibre forms at all concentrations to acrylic resin did not produce a statistically significant increase in the fatigue resistance (p ≥ 0.05). This study also revealed that there were significant differences (p < 0.05) between glass fibres forms used concerning the effects on the fatigue resistance. Conclusion: This study showed that the woven glass fibres had a definite superiority over the chopped fibres and the continuous fibres in regard to the fatigue resistance of the acrylic denture base resin.     

Effectiveness of different cleaning agents on the adherence of Candida albicans to acrylic denture base resin

doi: 10.1111/j.1741‐2358.2010.00379.x
Effectiveness of different cleaning agents on the adherence of Candida albicans to acrylic denture base resin Objective:  To evaluate the ability of three alkaline peroxide‐type (Polident, Efferdent, Fittydent) and two mouth rinse cleaning agents (CloSYSII and Corsodyl) to inhibit Candida albicans on acrylic denture base resin. Background:  Appropriate routine cleaning of dentures is necessary to prevent denture stomatitis and maintenance of healthy supporting tissues. Materials and methods:  A total of 180 acrylic resin specimens (10 × 10 × 2 mm) were prepared and divided into six groups. Candida albicans was incubated on Sabouraud dextrose agar (SDA) at 37°C for 48 h. After dilution, a final yeast suspension of approximately 10 6 C. albicans per millimetre was prepared. Ten acrylic resin specimens for each group were placed in a sterile Petri dish covered with 20 ml of fungal suspension and incubated at 37°C for 90 min. Then, the specimens were immersed in 40 ml of the test solution at 37°C for 15, 30 and 60 min. Fungal cells adhering to acrylic resin surfaces were fixed in formaldehyde and counted microscopically. Results:  Mouth rinses showed the highest removal activity for all the treatment times and completely eliminated the adherence of C. albicans. Conclusions:  The use of mouth rinse may be a suitable method for cleaning dentures.     

The occurrence of porosity in reline acrylic resins. Effect of microwave disinfection

Background: Microwave energy has proved to be an effective method for disinfecting acrylic dentures. However, the effect of microwave heating on the porosity of autopolymerising denture reline resins has not been investigated. Objective: The purpose of the study was to determine the effect of microwave disinfection on the porosity of autopolymerised denture reline materials (Kooliner‐K, New Truliner‐NT, Tokuso Rebase Fast‐TR and Ufi Gel Hard‐UGH) and a conventional heat‐polymerised denture base resin (Lucitone 550‐L). Material and methods: Specimens (10 mm × 20 mm × 1 mm) were obtained from the impression surface of the palatal mucosa in a single person and divided into four groups (n = 5). The porosity was evaluated after polymerisation (C1), after two cycles of microwave disinfection (MW2), after seven cycles of microwave disinfection (MW7) and after 7 days storage in water at 37°C (C2). Specimens from group MW7 were exposed to microwave disinfection daily being stored in water at 37°C between exposures. All the replicas were sputter coated with gold and micrographs/digital images were taken of each replica using scanning electron microscopy at magnification × 100. The SEM micrographs were then examined using an image analyser to determine the number of pores. Comparison between materials and groups were made using Kruskal–Wallis tests. Results: MW7 resulted in a significant increase in the number from the pores of material K, but decreased in number in reline material TR and UGH reline resin. The number of pores in materials NT and L remained unaffected following microwave disinfection. Conclusion: Differences in the porosity amongst the materials and for different experimental conditions were observed following microwave disinfection.     

The satisfaction with the removable partial denture therapy in the Croatian adult population

Little is known about the outcomes of treatment and patient's satisfaction with removable partial dentures in adult Croatian population. Therefore patient's satisfaction with their partial dentures in relation to some socio-economic variables was studied. Patient's satisfaction with denture retention, speech, aesthetics, comfort of wearing dentures, chewing ability was also studied in relation to different denture classification, construction, material, denture base shape (major connectors), denture support and the number of missing teeth. A total of 165 patients, 59 males and 105 females between 38 and 87 years took part in this study. A questionnaire, devised for a purpose of the study, was divided into three parts. In the first part, patients answered questions about age, gender, marital status, education, general health, socio-economic status, self-supporting life, period of tooth loss and number of previous denture experiences and in the second part, patients graded their partial dentures, depending on the level of satisfaction, by using a scale from 1 to 5. In the third part a dentist determined Kennedy classification and their modifications, denture material and denture support, denture base shape and the number of missing teeth and graded a denture construction. Influence of these factors on patient's satisfaction was analyzed. A majority of the examined patients were satisfied with the partial prosthesis, but a small amount of dissatisfaction existed. More then half of them scored all the examined parameters to the best score category. Considering chewing with lower partial dentures, women were more satisfied than men (p < 0.05). Patients with more missing teeth gave lower grades for the comfort of wearing dentures (p < 0.05). Patients of higher education gave lower grades (p < 0.05) for the aesthetics. Patients were not satisfied with speech if the dentist graded a construction of a lower partial denture low (p < 0.05). Dissatisfaction was related to mastication, aesthetics, number of missing teeth and ability of speech. These findings can aid a clinician in discussing a treatment plan and help a patient understand the risk of dissatisfaction in the presence of certain factors.     

Fracture resistance of maxillary complete dentures subjected to long-term water immersion

doi: 10.1111/j.1741‐2358.2012.00616.x Fracture resistance of maxillary complete dentures subjected to long‐term water immersion Objective: This study investigated the fracture resistance of maxillary acrylic resin complete dentures subjected to long‐term water immersion. Materials and Methods: Maxillary acrylic resin complete dentures were fabricated from five denture base resins. Half of the dentures were stored in water for 50 h, and the other half were kept in water for 180 days before testing. Ten specimens were fabricated per group. The flexural load at the proportional limit (FL‐PL) of the dentures was tested. Results: A two‐way anova revealed a significant difference in FL‐PL because of the denture base material variable. There were no significant differences in FL‐PL because of the effect of water immersion and the interaction between the effect of water immersion and the denture base material. The FL‐PLs of the dentures fabricated with the two conventional heat‐processed resins, the pour‐type autopolymerizing resin and the microwave energy‐processed resin were not significantly different from each other; they were significantly higher than the light‐activated resin in regard to their FL‐PL. Conclusion: The FL‐PLs of the maxillary acrylic resin complete dentures did not change after long‐tern water immersion, and the FL‐PL of the denture fabricated from the light‐activated resin was lower than those of the other materials.     

Correlation between factors associated with the removable partial dentures use and Candida spp. in saliva

doi: 10.1111/j.1741‐2358.2010.00390.x
Correlation between factors associated with the removable partial dentures use and Candida spp. in saliva Objectives: To correlate the presence and number of Candida spp. in the saliva of wearers of removable partial dentures retained with precision attachments with the proportion of metal/acrylic resin present in the dentures. Methods: Saliva samples from 40 removable partial denture wearers (test) and one paired sample of individuals, non‐wearers of any type of removable denture (control) were collected, seeded, and the colony forming units of Candida counted and identified. The metal/acrylic resin proportion of each denture was quantified, using silicone plates pressed over each denture. Results: Candida spp. was found in the saliva of 80% of the individuals in the test group and 65% of the control, with C. albicans being the most prevalent species. The test group presented with the highest number of colony forming units of Candida per ml of saliva, and there was weak correlation between this number and the metal and resin area of the denture (Pearson’s coefficient of correlation). Greater prevalence and a higher number of colony forming units of Candida per ml of saliva occurred in removable partial denture wearers (p = 0.04) with a weak positive correlation between the metal and resin area and the number of colony forming units of Candida per ml of saliva. However, this correlation was more significant for the area of resin.     

Survival analysis of mandibular complete dentures with acrylic‐based resilient liners

doi: 10.1111/j.1741‐2358.2012.00658.x Survival analysis of mandibular complete dentures with acrylic‐based resilient liners Objective: The purpose of this long‐term randomised controlled trial was to compare the longevity of dentures constructed using a conventional acrylic resin (CAR) to that of dentures constructed using an acrylic‐based resilient liner (ARL). Materials and methods: The follow‐up study was essentially carried out by annual telephone calls to each of the 67 participants. The Kaplan–Meier method and life‐table analysis were used for univariate analyses. The Cox proportional‐hazards test was used as a final model for statistically adjusting predictor variables such as sex, clinician type, mandibular denture type and age at denture delivery. Results: The denture type was likely to affect the survival time of the dentures, while the sex and clinician type were not. The group using acrylic‐based resilient denture liners had twice the risk of having shorter denture‐survival times than those using conventional acrylic resin dentures. Younger participants were likely to have a reduced risk of having shorter denture‐survival times than older participants. Conclusion: We conclude that mandibular complete dentures constructed using ARL are twice as likely as dentures constructed using CAR to have shorter denture survival times, mainly because of material deterioration.     

Effect of reline material and denture base surface treatment on the impact strength of a denture base acrylic resin

doi:10.1111/j.1741‐2358.2009.00292.x
Effect of reline material and denture base surface treatment on the impact strength of a denture base acrylic resin Objective: In this study, the effect of relining and surface treatment on the impact strength (IS) of a heat‐polymerising denture base acrylic resin (Lucitone 550‐L) was evaluated. Materials and methods: Rectangular bars of L were made (60 × 6 × 2 mm) and relined (2 mm) with the relining resins Ufi Gel Hard (UH) and Tokuso Rebase Fast (TR). Specimens relined with L and intact L, TR and UH specimens were also made (60 × 6 × 4 mm), for comparison. Before relining, the L surface was left untreated or wetted with methyl methacrylate monomer and/or the bonding agents (BA) supplied by manufacturers of the reline resins. V‐notches were machined at the midpoint of the length of all specimens. The notches were made either across the width (Nw) or across the thickness of the specimens (Nth). The Charpy impact test was performed using a 0.5‐J pendulum, which had been specially designed and constructed. Data were analysed separately for each notch position using one‐way analysis of variance and Tukey honestly significant difference post‐hoc test (p = 0.05). Results: The IS of L was similar to that of L/L. For the Nw notch, treating the denture base L with TR BA and relining with TR reline material produced the highest IS. Conclusion: The IS of specimens made from heat polymerising acrylic resin Lucitone 550 was increased after relining using the hard chairside reline resin TR with its proprietary BA.     

Effect of monomer treatment and polymerisation methods on the bond strength of resin teeth to denture base material

Background: The fracture between acrylic denture base material and artificial teeth is a common clinical occurrence in dental prosthodontic practice. Objective: To evaluate the bond strength between acrylic resins and resin denture teeth when submitted by two protocols of monomer liquid application on the tooth surface and using different polymerisation methods. Material and methods: Microwave‐polymerised (Onda‐Cryl), heat‐polymerised (Clássico) and autopolymerising (Jet) acrylic resins and a brand of resin denture teeth (Biotone) were used. The acrylic resins were polymerised according to the cycles: (A) microwave – fast cycle, Onda‐Cryl; (B) microwave – long cycle, Onda‐Cryl; (C) microwave – manufacturer’s cycle, Onda‐Cryl; (T) water bath – long cycle, Clássico and (Q) bench polymerisation cycle, Jet. Thirty specimens were prepared for each polymerisation method; 10 were packed with acrylic resin after 60 s of monomer liquid application on the tooth surface, 10 after 180 s and 10 without any monomer liquid application. For the purpose of the study, a shear test was used. anova and Tukey tests were performed to identify significant differences (α = 0.05). Results: The highest bond strength values were found for monomer surface treatments, regardless of the polymerisation cycles. The highest significant values were found for cycles B (15.4 ± 1.8 MPa), C (11.9 ± 4.9 MPa) and T (15.4 ± 2.6 MPa) for non‐treated and 60 s methylmethacrylate treated groups. Comparing the monomer liquid treatment, they did not differ significantly (p > 0.05), except for cycle A (p < 0.05). Conclusion: Chemical treatment using monomer on the tooth surface prior to the acrylic resin packing improved the bond strength between resin denture tooth and acrylic resin, regardless of monomer liquid treatment protocols. The microwavable resin, polymerised by fast cycle and autopolymerising resin should be avoided for processing denture and denture repairs, respectively.     

Antimicrobial activity of denture adhesive associated with Equisetum giganteum- and Punica granatum-enriched fractions against Candida albicans biofilms on acrylic resin surfaces

Candida biofilms adhere to the internal surface of removable dentures, which is an etiological factor in the pathogenesis of denture stomatitis (DS). Adhesive materials are used at the base of maxillary complete dentures to improve their retention and chewing qualities. This article reports the antimicrobial activity of the enriched fractions of Equisetum giganteum and Punica granatum incorporated into a denture adhesive against C. albicans biofilm. The biofilms were induced on the surface of heat-cured acrylic resin specimens that were previously treated with a mixture of adhesive/herb extracts. The antimicrobial activity was evaluated by CFU counts, XTT reduction, and SEM and CLSM analysis. Both herb extracts amplified the anti-biofilm action of the adhesive on the acrylic resin by up to 12 h. Therefore, when these extracts were combined with COREGA®, they played a collaborative and innovative role in biofilm control and can be considered alternatives for temporary use in the treatment and/or prevention of DS.     

Evaluation of Vickers hardness of different types of acrylic denture base resins with and without glass fibre reinforcement

doi: 10.1111/j.1741‐2358.2010.00435.x
Evaluation of Vickers hardness of different types of acrylic denture base resins with and without glass fibre reinforcement Objective: To evaluate the Vickers hardness of different acrylic resins for denture bases with and without the addition of glass fibres. Background: It has been suggested that different polymerisation methods, as well as the addition of glass fibre (FV) might improve the hardness of acrylic. Materials and methods: Five types of acrylic resin were tested: Vipi Wave (VW), microwave polymerisation; Vipi Flash (VF), auto‐polymerisation; Lucitone (LT), QC20 (QC) and Vipi Cril (VC), conventional heat‐polymerisation, all with or without glass fibre reinforcement (GFR) and distributed into 10 groups (n = 12). Specimens were then submitted to Vickers hardness testing with a 25‐g load for 30 s. All data were submitted to anova and Tukey’s HSD test. Results: A significant statistical difference was observed with regard to the polymerisation method and the GFR (p < 0.05). Without the GFR, the acrylic resin VC presented the highest hardness values, and VF and LT presented the lowest. In the presence of GFR, VC resin still presented the highest Vickers hardness values, and VF and QC presented the lowest. Conclusions: The acrylic resin VC and VW presented higher hardness values than VF and QC resins. Moreover, GFR increased the Vickers hardness of resins VW, VC and LT.     

Effect of thermal cycling on microleakage between hard chairside relines and denture base acrylic resins

doi:10.1111/j.1741‐2358.2009.00332.x
Effect of thermal cycling on microleakage between hard chairside relines and denture base acrylic resins Objectives: Microleakage is a pre‐stage of debonding between hard chairside relines and denture base acrylic resins. Therefore, it is important to assess them with regard to the longevity of the relined denture. This study investigated the effect of thermal cycling on the microleakage at the interface of three hard chairside reline resins and three denture base resins. Material and methods: Rectangular bars (12 mm × 3 mm × 3 mm) of Lucitone 550, Acron MC and QC 20 were made and relined with Kooliner, Tokuyama Rebase Fast II and Ufi Gel Hard, Lucitone 550, Acron MC and QC 20 resins. Specimens were divided into one control and two test groups (n = 10). In specimens of the control group, the microleakage was performed after the reline procedure. In Test Group 1, the specimens were stored for 24 h in distilled water at room temperature and in Test Group 2; the specimens were thermal cycled from 5 to 55°C for 5000 cycles with a 30‐s dwell time. Subsequently, all specimens were immersed in 50% silver nitrate solutions for 24 h. All specimens were sectioned longitudinally into three fractions and the lateral sections were examined (n = 20). Silver nitrate stain penetration was examined under a stereoscopic lens with ×30 magnification, and the images were captured. Leica Qwin image analysis software was used to determine microleakage at the interface of the materials. Data were analysed using the Kruskal–Wallis test at a 95% level of significance. Results: For all cycles, there were no statistically significant differences between thermal cycled and non‐thermal cycled groups (p > 0.05). Conclusion: It can be concluded that thermal cycling had no effect on the microleakage.     

In vitro antiseptic properties of an ammonium compound combined with denture base acrylic resin

Background: Denture base acrylic resin is easily colonised by oral endogenous bacteria and Candida spp., and eventually by extra‐oral species such as Staphylococcus spp., Pseudomonadaceae or members of Enterobacteriaceae. This microbial reservoir can be responsive for denture related stomatitis and aspiration pneumonia, a life‐threatening infection especially in geriatric patients. However, the oral and denture hygiene of dependant elderly individuals is extremely poor. Objective: This in vitro study aimed to determine the per cent of a quaternary ammonium compound heat‐polymerised in acrylic resin necessary to obtain denture base displaying antiseptic properties. Design: Acrylic resin discs containing 2–50% ammonium polymer (Poly 202063A; 0% control) were soaked in artificial saliva for 4 weeks. Resin discs were incubated for 24 hours with Escherichia coli, Staphylococcus aureus, Pseudomonas aeruginosa [37°C, brain–heart infusion (BHI) broth and phosphate‐buffered saline (PBS) buffer] and Candida albicans (30°C, Schaedler broth), in 15 ml (168 discs) and 600 μl (168 discs) of inoculum. Microbial growth was verified at t 0 hours and t 24 hours. Data were recorded as the mean of three colony forming unit (CFU) numerations. The borderline of antimicrobial effect was determined at 0.1% viable cells. Results: In 600 μl of PBS inoculum, resin specimens had a bactericidal effect (E. coli and S. aureus: 2%; P. aeruginosa: 10%) and a fungicidal effect (C. albicans: 50%). Long‐term stability and toxicity in vivo studies are now required. Conclusion: A 2% quaternary ammonium compound polymerised with a denture acrylic resin displayed antiseptic properties after a 4‐week soaking period in artificial saliva. Such antiseptic denture base could help geriatric patients to improve their oral health.     

Effect of thermal cycling and disinfection on colour stability of denture base acrylic resin

doi: 10.1111/j.1741‐2358.2012.00676.x Effect of thermal cycling and disinfection on colour stability of denture base acrylic resin Objectives: The purpose of this study was to investigate the effect of thermal cycling and disinfection on the colour change of denture base acrylic resin. Materials and Methods: Four different brands of acrylic resins were evaluated (Onda Cryl, QC 20, Classico and Lucitone). All brands were divided into four groups (n = 7) determined according to the disinfection procedure (microwave, Efferdent, 4% chlorhexidine or 1% hypochlorite). The treatments were conducted three times a week for 60 days. All specimens were thermal cycled between 5 and 55°C with 30‐s dwell times for 1000 cycles before and after disinfection. The specimens’ colour was measured with a spectrophotometer using the CIE L*a*b* system. The evaluations were conducted at baseline (B), after first thermal cycling (T₁), after disinfection (D) and after second thermal cycling (T₂). Colour differences (ΔE) were calculated between T₁ and B (T₁B), D and B (DB), and T₂ and B (T₂B) time‐points. Results: The samples submitted to disinfection by microwave and Efferdent exhibited the highest values of colour change. There were significant differences on colour change between the time‐points, except for the Lucitone acrylic resin. Conclusions: The thermal cycling and disinfection procedures significantly affected the colour stability of the samples. However, all values obtained for the acrylic resins are within acceptable clinical parameters.     

Genetic diversity of gamma-hexachlorocyclohexane-degrading sphingomonads isolated from a single experimental field

Aim:  To determine the effect of the surface roughness of denture acrylic on the attachment of Streptococcus oralis .
Methods and Results:  Roughened denture acrylic samples were assessed for bacterial attachment, over time, using microscopy. The area of the image covered by bacteria was calculated and converted into a percentage of the total area sampled. The results showed an increasing bacterial coverage with time of incubation and increasing roughness. Differences were seen between heat cured acrylic and cold cured acrylic.
Conclusion:  This study successfully demonstrated a system for the assessment of the amount of attached bacteria on denture acrylic varying roughness. The system was able to discern the difference in surface area coverage by attached bacteria over a roughness range relevant to brushing dentures with dentifrices.
Significance and Impact of Study:  This study provides strong support for the scratches caused by brushing dentures with dentifrice encouraging bacterial attachment. This is likely to have a significant effect on efficacy of denture cleaning, general hygiene and biofilm re-formation between cleaning regimens and may indicate that alternative low abrasive cleaners, such as antimicrobial denture-cleaning tablets, offer a more appropriate regimen.