Chromatographic analysis of griseofulvin and metabolites in biological fluids

A simple and accurate assay for the determination of griseofulvin and its metabolites in biological fluids using high-performance liquid chromatography is described. Using a reversed phase column and a mobile phase solvent of 45% acetonitrile in 0.1 M acetic acid, baseline separation of griseofulvin and several analogues was obtained. The described method allows one to quantitatively determine griseofulvin, 6-demethylgriseofulvin, and griseofulvic acid, a newly identified metabolite in man, in urine and plasma samples. Treatment of plasma samples prior to the analysis is simply made by deproteinizing the samples with an equal volume of acetonitrile. For urine samples, the procedure involves diethyl ether extraction with subsequent evaporation to dryness and reconstitution with the mobile phase solvent.     

Measurement of bumetanide in plasma and urine by high-performance liquid chromatography and application to bumetanide disposition

A high-performance liquid chromatographic method for the measurement of bumetamide in plasma and urine is described. Following precipitation of proteins with acetonitrile, bumetanide was extracted from plasma or urine on a 1-ml bonded-phase C₁₈ column and eluted with acetonitrile. Piretanide dissolved in methanol was used as the internal standard. A C₁₈ Radial Pak column and fluorescence detection (excitation wavelength 228 nm; emission wavelength 418 nm) were used. The mobile phase consisted of methanol—water—glacial acetic acid (66:34:1, v/v) delivered isocratically at a flow-rate of 1.2 ml/min. The lower limit of detection for this method was 5 ng/ml using 0.2 ml of plasma or urine. Nafcillin, but not other semi-synthetic penicillins, was the only commonly used drug that interfered with this assay. No interference from endogenous compounds was detected. For plasma, the inter-assay coefficients of variation of the method were 7.6 and 4.4% for samples containing 10 and 250 ng/ml bumetanide, respectively. The inter-assay coefficients of variation for urine samples containing 10 and 2000 ng/ml were 8.1 and 5.7%, respectively. The calibration curve was linear over the range 5–2000 ng/ml.     

Rapid and Simple Reversed-Phase High-Performance Liquid Chromatography (RP-HPLC) Method for Simultaneous Quantifications of Triazole Antifungals in Human Serum

Purpose

To develop and validate a one-step, rapid and simple reversed-phase high-performance liquid chromatography (HPLC)-based protocol for the simultaneous measurement of voriconazole (VCZ), posaconazole (POSA), itraconazole (ITC) in serum/plasma.

Methods

Calibration standards (CS) and quality control samples were prepared in drug-free serum by spiking with the triazoles at different concentrations. HPLC was performed with C₁₈ column, isocratic mobile phase after extraction with cold acetonitrile. The standardized method was tested in 2693 patients’ serum/plasma samples.

Results

Linearity of CS for ITC, VCZ and POSA was proportional to the nominal concentration (correlation coefficient?>?0.999). Limit of detection (mg/L) for ITC, VCZ and POSA was 0.25, 0.25 and 0.125, respectively. The lower limit of quantification (mg/L) for ITC, VCZ and POSA was 0.5, 0.5 and 0.25, respectively. Precision and accuracy were in acceptable range with 100% average percentage recovery. No interferences from endogenous substances and other antimicrobial compounds were noted. In clinical samples, the therapeutic range achieved for VCZ was 39.9%. Whereas, 61.1% and 44% of samples with ITC and POSA, respectively, were in the sub-therapeutic range.

Conclusion

We developed a rapid and simple HPLC method to quantify common triazoles in a single chromatographic run allowing simultaneous measurement of different antifungals in a small volume of serum/plasma. Thus, therapeutic drug monitoring requests can be processed in one run without changing the protocol parameters, column or column conditioning thereby improving turnaround time.

     

Determination of [d-Ala2, d-Leu5]enkephalin and the metabolites containing C-terminal d-leucine by high-performance liquid chromatography

A high-performance liquid chromatographic procedure has been developed for the determination of [d-Ala², d-Leu⁵]enkephalin (DADLE) and the fragments containing d-leucine in rat blood. The procedure was applied to the determination of blood levels of [³H-d-Leu⁵]DADLE and the C-terminal fragments after intravenous administration of [³H-d-Leu⁵]DADLE to a rat. Unlabelled DADLE and the C-terminal fragments were spiked as carriers to rat blood samples and the blood samples were extracted with 1% trifluoroacetic acid in methanol. The recoveries from rat blood were quantitative for all compounds. DADLE and the C-terminal four fragments were well separated on a reversed-phase column with gradient elution using a mobile phase composed of 0.14% HClO₄ and acetonitrile.     

Determination of cycloserine in human plasma by high-performance liquid chromatography with fluorescence detection,using derivatization with p-benzoquinone

A new method for determining cycloserine in plasma samples is described. This method is based on the derivatization of cycloserine with p-benzoquinone, a reaction that takes place at the same time as the process of plasma deproteinization due to the presence of ethanol as solvent in the solution of the derivatization reagent. Four derivatives are obtained from this reaction. The main derivative is well correlated with the cycloserine concentration. The ratio between the volumes of the plasma sample and the reagent solution is 1:2 for a p-benzoquinone concentration of 1000 μg/mL. Elution from a C₁₈ column was isocratic, using a mobile phase containing (v/v) 85% aqueous 0.1% formic acid solution, and 15% (v/v) of a mixture of methanol and acetonitrile (1:1), with a flow-rate of 1 mL/min, at 25°C. Determinations by fluorescence detection were achieved with excitation at 381 nm and emission at 450 nm, with a detection limit of 10 ng/mL for an injection volume of 5 μL. This method was validated and applied to the determination of cycloserine in blood plasma samples of several healthy volunteers.     

Determination of [d-Ala, d-Leu]enkephalin and the metabolites containing C-terminal d-leucine by high-performance liquid chromatography

A high-performance liquid chromatographic procedure has been developed for the determination of [d-Ala², d-Leu⁵]enkephalin (DADLE) and the fragments containing d-leucine in rat blood. The procedure was applied to the determination of blood levels of [³H-d-Leu⁵]DADLE and the C-terminal fragments after intravenous administration of [³H-d-Leu⁵]DADLE to a rat. Unlabelled DADLE and the C-terminal fragments were spiked as carriers to rat blood samples and the blood samples were extracted with 1% trifluoroacetic acid in methanol. The recoveries from rat blood were quantitative for all compounds. DADLE and the C-terminal four fragments were well separated on a reversed-phase column with gradient elution using a mobile phase composed of 0.14% HClO₄ and acetonitrile.     

Should we measure serum or plasma lead concentrations?

ProjectSerum samples may not be appropriate to assess lead (Pb) concentrations because they may contain artificially higher Pb concentrations compared with those measured in plasma samples. Here, we compared Pb concentrations in serum versus heparin plasma separated from blood collected with or without vacuum. We have also examined the effects of sample standing time on Pb concentrations measured in serum, heparin plasma, and EDTA plasma.ProcedureWe studied plasma and serum samples from twelve healthy subjects. Blood samples were collected via venous drainage phlebotomy with and without vacuum into trace metal free tubes containing no anticoagulants (serum), or lithium heparin, or EDTA (to obtain plasma). Variable sample standing times (0, 5, and 30 min) prior to centrifugation were allowed. Plasma and serum Pb and iron concentrations were determined by inductively coupled plasma mass spectrometry. Plasma and serum cell-free hemoglobin concentrations were measured.ResultsPb concentrations in serum and in heparin plasma from blood samples collected with or without vacuum were similar and not associated with significant changes in iron or hemoglobin concentrations. The sample standing time (up to 30 min) did not affect Pb concentrations in serum or in heparin plasma, which were approximately 50% lower than those found in EDTA plasma.ConclusionsSerum or heparin plasma separated from blood samples collected via venous phlebotomy with or without vacuum are appropriate medium to assess Pb concentrations, independently of the sample standing time.     

Serum metabolomics identifies metabolite panels that differentiate lame dairy cows from healthy ones

Background

Metabolomics provides measurement of numerous metabolites in human samples, which can be a useful tool in clinical research. Blood and urine are regarded as preferred subjects of study because of their minimally invasive collection and simple preprocessing methods. Adhering to standard operating procedures is an essential factor in ensuring excellent sample quality and reliable results.

Aim of review

In this review, we summarize the studies about the impacts of various preprocessing factors on metabolomics studies involving clinical blood and urine samples in order to provide guidance for sample collection and preprocessing.

Key scientific concepts of review

Clinical information is important for sample grouping and data analysis which deserves attention before sample collection. Plasma and serum as well as urine samples are appropriate for metabolomics analysis. Collection tubes, hemolysis, delay at room temperature, and freeze–thaw cycles may affect metabolic profiles of blood samples. Collection time, time between sampling and examination, contamination, normalization strategies, and storage conditions may alter analysis results of urine samples. Taking these collection and preprocessing factors into account, this review provides suggestions of standard sample preprocessing.

     

Intercalative DNA Binding of Model Compounds Derived From Metabolites of 7, 12-Dimethylbenz[a]anthracene

Abstract

The DNA binding of nonreactive model compounds of metabolites of 7,12-dimethylbenz[a]-anthracene (DMBA)¹ was studied in fluorescence quenching and fluorescence lifetime experiments. The model compounds examined were DMA and 8,9,10,11-tetrahydro-BA. DMA is a π electron model of a highly carcinogenic bay region epoxide of DMBA. 8,9,10,11- tetrahydro-BA is a model compound of a less carcinogenic DMBA epoxide.

The results indicate that the binding of DMA occurs primarily via intercalation. In 15% methanol the binding constant is 3.1 × 10³M^?1. In 15% methanol and at DNA phosphate levels of 5.0 × ^?4 M the intercalative binding of DMA is reduced by a factor of 6.2 when 5.0 × 10^?4 M Mg⁺² is added. The DMA binding constant for intercalation is reduced by more than a factor of 4 when the methanol content of the solvent is increased from 0% to 20%. Finally DMA binding arising from π interactions with the DNA bases is reduced more than 15 times when the DNA is denatured. For 8,9,10,11-tetrahydro-BA in 15% methanol the binding constant for intercalation is 6 times lower than that for DMA.

These results along with previously reported binding data on other model compounds suggest that bay region metabolites of DMBA readily participate in physical π stacking interactions with DNA.     

Quantitative analysis of polychlorinated biphenyls, organochlorine insecticides, polycyclic aromatic hydrocarbons, polychlorinated hydrocarbons and polynitrohydrocarbons in spiked samples of soil, water and plasma by selected-ion monitoring gas chromatography–mass spectrometry

A broad range of pollutants such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated hydrocarbons (PCHs), polynitrohydrocarbons (PNHs), polychlorinated biphenyls (PCBs) and organochlorine (OCs) insecticides were simultaneously analyzed in spiked soil, water or plasma samples by using gas chromatography–mass spectrometry (GC–MS). Water and plasma samples containing the pollutants were extracted by a solid-phase extraction (SPE) method using florisil columns. The soil samples, fortified with the toxicants, were extracted with water, methanol or dichloromethane (DCM). The water extract was processed by the SPE method. The methanol and DCM samples were dried, dissolved in acetonitrile and subjected to the SPE extraction. The extracted samples were analyzed by GC–MS programmed to monitor selected ions. The deuterium labelled compounds were used as the internal standards. The chromatographic profile of total ions indicated complete separation of some compounds such as isophorone, naphthalene, all PCBs, most OC insecticides and PNHs; high M_r PAHs and some PCHs were partially or incompletely separated. The chromatographic profile of individual ion indicated good separation of each ion. The minimum detection limit ranged from 1 to 4 pg injected when 1 or 2 ions were monitored or from 20 to 200 pg injected when 20 ions were monitored. The SPE method that provided 60–105% recovery of pollutants from water samples, provided only 2–60% recovery from plasma samples. This may be due to the binding of pollutants to plasma proteins. Water recovered 1–30%, while methanol or DCM recovered 65–100% of the pollutants added to the soil samples. The use of internal standards corrected for the loss of pollutants from plasma or soil.     

Lignin Peroxidase Oxidation of Aromatic Compounds in Systems Containing Organic Solvents

Lignin peroxidase from Phanerochaete chrysosporium was used to study the oxidation of aromatic compounds, including polycyclic aromatic hydrocarbons and heterocyclic compounds, that are models of moieties of asphaltene molecules. The oxidations were done in systems containing water-miscible organic solvents, including methanol, isopropanol, N, N-dimethylformamide, acetonitrile, and tetrahydrofuran. Of the 20 aromatic compounds tested, 9 were oxidized by lignin peroxidase in the presence of hydrogen peroxide. These included anthracene, 1-, 2-, and 9-methylanthracenes, acenaphthene, fluoranthene, pyrene, carbazole, and dibenzothiophene. Of the compounds studied, lignin peroxidase was able to oxidize those with ionization potentials of <8 eV (measured by electron impact). The reaction products contain hydroxyl and keto groups. In one case, carbon-carbon bond cleavage, yielding anthraquinone from 9-methylanthracene, was detected. Kinetic constants and stability characteristics of lignin peroxidase were determined by using pyrene as the substrate in systems containing different amounts of organic solvent. Benzyl alkylation of lignin peroxidase improved its activity in a system containing water-miscible organic solvent but did not increase its resistance to inactivation at high solvent concentrations.     

Technology platform development for targeted plasma metabolites in human heart failure

Background

Heart failure is a multifactorial disease associated with staggeringly high morbidity and motility. Recently, alterations of multiple metabolites have been implicated in heart failure; however, the lack of an effective technology platform to assess these metabolites has limited our understanding on how they contribute to this disease phenotype. We have successfully developed a new workflow combining specific sample preparation with tandem mass spectrometry that enables us to extract most of the targeted metabolites. 19 metabolites were chosen ascribing to their biological relevance to heart failure, including extracellular matrix remodeling, inflammation, insulin resistance, renal dysfunction, and cardioprotection against ischemic injury.

Results

In this report, we systematically engineered, optimized and refined a protocol applicable to human plasma samples; this study contributes to the methodology development with respect to deproteinization, incubation, reconstitution, and detection with mass spectrometry. The deproteinization step was optimized with 20% methanol/ethanol at a plasma:solvent ratio of 1:3. Subsequently, an incubation step was implemented which remarkably enhanced the metabolite signals and the number of metabolite peaks detected by mass spectrometry in both positive and negative modes. With respect to the step of reconstitution, 0.1% formic acid was designated as the reconstitution solvent vs. 6.5 mM ammonium bicarbonate, based on the comparable number of metabolite peaks detected in both solvents, and yet the signal detected in the former was higher. By adapting this finalized protocol, we were able to retrieve 13 out of 19 targeted metabolites from human plasma.

Conclusions

We have successfully devised a simple albeit effective workflow for the targeted plasma metabolites relevant to human heart failure. This will be employed in tandem with high throughput liquid chromatography mass spectrometry platform to validate and characterize these potential metabolic biomarkers for diagnostic and therapeutic development of heart failure patients.     

Simultaneous quantitation of plasma doxorubicin and prochlorperazine content by high-performance liquid chromatography

A high-performance liquid chromatographic method has been developed and tested for simultaneous extraction, elution and determination of doxorubicin and prochlorperazine content in human plasma samples. The procedure consists of extraction through a conditioned C₁₈ solid-phase extraction cartridge, elution from a Spherisorb C₈ reversed-phase column by an isocratic mobile phase (60% acetonitrile, 15% methanol and 25% buffer) followed by detection with electrochemical and fluorescence detectors. Recovery of doxorubicin and prochlorperazine from pooled human plasma samples (n=3) containing 100 ng/ml of the two drugs was 77.8±3.5% and 89.1±6.0%, respectively. The lower limits of quantitation for doxorubicin and prochlorperazine in plasma samples were 6.25 ng/ml and 10 ng/ml, respectively. A linear calibration curve was obtained for up to 2 μg/ml of doxorubicin and prochlorperazine. This combination method may be of particular value in clinical studies where phenothiazines such as prochlorperazine are used to enhance retention of doxorubicin in drug resistant tumor cells.     

Quinazoline-sulfonamides as potential antitumor agents: synthesis and biological testing

Abstract

New series of quinazoline containing sulfonamide derivatives were prepared and screened for their antitumor activity. Four human cancer cell lines, namely, hepatoma cancer cell line (HepG2), breast cancer cell line (MCF-7), cervix cancer cell line (HeLa) and colon cancer cell line (HCT-8), were used to measure the cytotoxic activity. Compounds 8 and 21 exhibited remarkable antitumor activity almost similar to that of the standard drug (doxorubicin). Six compounds 16, 22, 23, 29, 30 and 33, showed considerable activity and few compounds were totally inactive.     

Stereoselective enzymatic esterification of 3-benzoylthio-2-methylpropanoic acid

Summary A key intermediate, S-(–)-3-benzoylthio-2-methylpropanoic acid (1) was made in high optical purity by the lipase-catalyzed stereoselective esterification of racemic 1 with methanol in an organic solvent system. Among various lipases evaluated, Amano P-30 lipase from Pseudomonas sp. efficiently catalyzed the esterification of 1 to yield R-(+) methyl ester and unreacted S-(–) 1. A reaction yield of 40 mol% and an optical purity of 97.2% were obtained for compound 1 at a substrate concentration of 0.1 m (22 mg/ml). Lipase P-30 was immobilized on Accurel polypropylene (PP) and the immobilized enzyme was reused (23 cycles) in the esterification reaction without loss of enzyme acitivity, productivity or optical purity. Among various solvents evaluated, toluene was found to be the most suitable organic solvent and methanol was the best alcohol for the esterification of racemic 1 by immobilized lipase. Substrate concentrations as high as 1.0 m were used in the esterification reaction. When the temperature was increased from 28° C to 60° C, the reaction time required for the esterification of 0.1 m substrate decreased from 16 h to 2 h. On increasing the methanol to substrate molar ratio from 1:1 to 4:1, the rate of esterification decreased. A lipase fermentation using Pseudomonas sp. ATCC 21 808 was developed. In the batch-fermentation process, 56 units/ml of extracellular lipase activity was obtained. A fed-batch process using soybean oil gave a significant increase in the lipase activity (126 units/ml). Crude lipase recovered from the filtrate by ethanol precipitation and immobilized on Accurel PP was also effective: S-(–) compound 1 was obtained in 35 mol% yield and 95% optical purity. Offsprint requests to: R. N. Patel     

Replacement of acetonitrile by ethanol as solvent in reversed phase chromatography of biomolecules

Acetonitrile, which is a by-product of acrylonitrile synthesis, is the commonly used solvent in ion-pair reversed phase chromatography. In consequence of the decreasing demand for acrylonitrile due to the financial crisis, a worldwide shortage of acetonitrile is observed. Therefore, the aim of this study was to establish ion-pair reversed phase chromatographic assays using alternative eluents for acetonitrile and to decrease costs incurred hereby. We compared the performance of ion-pair reversed phase chromatography using acetonitrile with the alternative eluents methanol, ethanol and n-propanol, using monolithic reversed phase C5 as well as C18 chromatography columns. We used triethylammonium acetate (TEAA) and tetrabutylammonium sulfate (TBA) as representative cationic ion-pair reagents and trifluoroacetic acid (TFA) as representative anionic ion-pair reagent. For covering a large field of applications, we fractionated representative low, middle and high-molecular weight biomolecules, in particular dinucleoside polyphosphates, peptides, proteins and tryptic digested human serum albumin. Whereas the chromatographic characteristics of both methanol and n-propanol were partly insufficient, ethanol was characterised equally or partly even better in the matter of elution strength and separation quality compared to the eluent water–acetonitrile. In conclusion, ethanol is an appropriate alternative for acetonitrile in ion-pair reversed phase chromatography of biomolecules.     

Neutrophil gelatinase-associated lipocalin after off pump versus on pump coronary artery surgery

Abstract

Context: Cardiac surgery.

Objective: To compare plasma and urinary neutrophil gelatinase-associated lipocalin (P-/U-NGAL) in on-pump (n?=?43) versus off-pump (n?=?40) surgery.

Materials and methods: We obtained perioperative P-/U-NGAL and outcome data.

Results: P-/U-NGAL increased after surgery. P-NGAL was higher post-surgery in on pump patients (139 versus 67?µg L^?1; p?<?0.001), but not at 24?h. There were no differences in U-NGAL. Correlation between P-/U-NGAL and plasma creatinine was weak.

Discussion: P-NGAL acts like a neutrophil activation biomarker and U-NGAL like a tubular injury marker.

Conclusion: On-pump patients had greater neutrophil activation. On- versus off-pump surgery had similar impact on tubular cells.     

Preparative High Performance Chromatography of a Major Browning Compound Derived from Lysine and Glucose

ABSTRACT

A major browning compound derived from lysine and glucose was purified by high performance chromatography on a RP8 column after several extractions in methanol plus acetonitrile. This compound was separated by a main contaminant corresponding to unreacted lysine by extracting the aminoacid after its derivatization with ninhydrin.