Combined removal of sulfur compounds and nitrate by autotrophic denitrification in bioaugmented activated sludge system

An autotrophic denitrification process using reduced sulfur compounds (thiosulfate and sulfide) as electron donor in an activated sludge system is proposed as an efficient and cost effective alternative to conventional heterotrophic denitrification for inorganic (or with low C/N ratio) wastewaters and for simultaneous removal of sulfide or thiosulfate and nitrate. A suspended culture of sulfur-utilizing denitrifying bacteria was fast and efficiently established by bio-augmentation of activated sludge with Thiobacillus denitrificans. The stoichiometry of the process and the key factors, i.e. N/S ratio, that enable combined sulfide and nitrogen removal, were determined. An optimum N/S ratio of 1 (100% nitrate removal without nitrite formation and low thiosulfate concentrations in the effluent) has been obtained during reactor operation with thiosulfate at a nitrate loading rate (NLR) of 17.18 mmol N L(-1) d(-1). Complete nitrate and sulfide removal was achieved during reactor operation with sulfide at a NLR of 7.96 mmol N L(-1) d(-1) and at N/S ratio between 0.8 and 0.9, with oxidation of sulfide to sulfate. Complete nitrate removal while working at nitrate limiting conditions could be achieved by sulfide oxidation with low amounts of oxygen present in the influent, which kept the sulfide concentration below inhibitory levels.     

包埋法固定化对硫氧化微生物菌群结构和功能的影响

【目的】为探讨包埋法固定化过程对硫氧化菌群硫化物去除能力及菌群微生物群落结构的影响,【方法】以聚乙烯醇-海藻酸钠-活性炭为载体,对硫氧化菌群进行了固定化,并采用富含硫化物的无机盐培养基,对比固定化与非固定化硫氧化菌群对硫化物的氧化去除能力。同时,利用PCR-DGGE技术,探讨硫氧化菌群在固定化前后以及在硫化物氧化去除过程中微生物群落结构变化。【结果】在对硫氧化菌群进行固定化之后,12 h之内对硫化物的最大去除能力从1000 mg/L下降为600 mg/L。硫氧化菌群的微生物群落结构发生了明显变化,但菌群中的硫氧化菌Catenococcus thiocycli未受影响,硫氧化菌Thioclava pacifica在菌群中的地位反而得到了强化。【结论】受制于底物在载体材料中的扩散迁移效率,硫氧化菌群对硫化物的氧化去除能力在固定化之后有所下降。由于不同微生物对固定化形成的微环境的适应能力以及对载体附着能力的不同,固定化对硫氧化菌群的微生物群落结构产生较大影响。     

Sulfide oxidation under chemolithoautotrophic denitrifying conditions

Chemolithoautotrophic denitrifying microorganisms oxidize reduced inorganic sulfur compounds coupled to the reduction of nitrate as an electron acceptor. These denitrifiers can be applied to the removal of nitrogen and/or sulfur contamination from wastewater, groundwater, and gaseous streams. This study investigated the physiology and kinetics of chemolithotrophic denitrification by an enrichment culture utilizing hydrogen sulfide, elemental sulfur, or thiosulfate as electron donor. Complete oxidation of sulfide to sulfate was observed when nitrate was supplemented at concentrations equal or exceeding the stoichiometric requirement. In contrast, sulfide was only partially oxidized to elemental sulfur when nitrate concentrations were limiting. Sulfide was found to inhibit chemolithotrophic sulfoxidation, decreasing rates by approximately 21-fold when the sulfide concentration increased from 2.5 to 10.0 mM, respectively. Addition of low levels of acetate (0.5 mM) enhanced denitrification and sulfate formation, suggesting that acetate was utilized as a carbon source by chemolithotrophic denitrifiers. The results of this study indicate the potential of chemolithotrophic denitrification for the removal of hydrogen sulfide. The sulfide/nitrate ratio can be used to control the fate of sulfide oxidation to either elemental sulfur or sulfate.     

Performance of a substratum-irradiated photosynthetic biofilm reactor for the removal of sulfide from wastewater

The performance of a sulfide-removal system based on biofilms dominated by green sulfur bacteria (GSB) has been investigated. The system was supplied with radiant energy in the band 720-780 nm, and fed with a synthetic wastewater. The areal net sulfide removal rate and the efficacy of the incident radiant energy for sulfide removal have been characterized over ranges of bulk sulfide concentration (1.6-11.5 mg L(-1)) and incident irradiance (0.21-1.51 W m(-2)). The areal net sulfide removal rate increased monotonically with both increasing incident irradiance and increasing bulk sulfide concentration. The efficacy of the radiant energy for sulfide removal (the amount of sulfide removed per unit energy supplied) also increased monotonically with rising bulk sulfide concentration, but exhibited a maximum value with respect to incident irradiance. The maximum observed values of this net removal rate and this efficacy were, respectively, 2.08 g m(-2) d(-1) and 2.04 g W(-1) d(-1). In-band changes in the spectral composition of the radiant energy affected this efficacy only slightly. The products of sulfide removal were sulfate and elemental-S. The elemental-S was scarcely released into the liquid, however, and reasons for this, such as sulfur reduction and polysulfide formation, are considered. Between 1.45 and 3.85 photons were needed for the net removal of one electron from S-species. Intact samples of the biofilm were characterized by microscopy, and their thicknesses lay between 39 +/- 9 and 429 +/- 57 microm. The use of the experimentally determined rates and efficacies for the design of a pilot-scale system is illustrated.     

Effect of hydrogen sulfide on growth of sulfate reducing bacteria

A culture of sulfate reducing bacteria (SRB) growing on lactate and sulfate was incubated at different pH values in the range of 5.8-7.0. The effect of pH on growth rate was determined in this pH range; the highest growth rate was observed at pH 6.7. Hydrogen sulfide produced from sulfate reduction was found to have a direct and reversible toxicity effect on the SRB. A hydrogen sulfide Concentration of 547 mg/L (16.1 mM) completely inhibited the culture growth. Comparison between acetic acid and hydrogen sulfide inhibition is presented and the concomitant inhibition kinetics are mathematically described. (c) 1992 John Wiley & Sons, Inc.     

Influence of synthesis parameters on the optical and photocatalytic properties of solvo/hydrothermal CuS and ZnS nanoparticles

Copper sulfide and zinc sulfide nanostructures were synthesized using a solvo/hydrothermal method and a thio Schiff base ligand, N‐benzylidene ethanethioamide, as a source of sulfide ions. The effects of different synthesis parameters including the type of solvent, temperature, and duration of reactions on the morphology of the CuS and ZnS products were investigated using field emission scanning microscopy and transmission electron microscopy, respectively. The structural aspects of the samples were characterized using powder X‐ray diffraction, Fourier transform infrared spectroscopy, and energy dispersive X‐ray analysis. The optical properties of the samples were studied through their optical absorption and photoluminescence spectra. The photocatalytic ability of the as‐synthesized sulfides was explored by studying the colour removal of methylene blue under ultraviolet light irradiation.     

Nitrate promotes biological oxidation of sulfide in wastewaters: experiment at plant-scale

Biogenic production of sulfide in wastewater treatment plants involves odors, toxicity and corrosion problems. The production of sulfide is a consequence of bacterial activity, mainly sulfate-reducing bacteria (SRB). To prevent this production, the efficiency of nitrate addition to wastewater was tested at plant-scale by dosing concentrated calcium nitrate (Nutriox) in the works inlet. Nutriox dosing resulted in a sharp decrease of sulfide, both in the air and in the bulk water, reaching maximum decreases of 98.7% and 94.7%, respectively. Quantitative molecular microbiology techniques indicated that the involved mechanism is the development of the nitrate-reducing, sulfide-oxidizing bacterium Thiomicrospira denitrificans instead of the direct inhibition of the SRB community. Denitrification rate in primary sedimentation tanks was enhanced by nitrate, being this almost completely consumed. No significant increase of inorganic nitrogen was found in the discharged effluent, thus reducing potential environmental hazards to receiving waters. This study demonstrates the effectiveness of nitrate addition in controlling sulfide generation at plant-scale, provides the mechanism and supports the environmental adequacy of this strategy.     

Photo-autotrophic growth of Thiocapsa roseopersicina on dimethyl sulfide

Abstract: The purple sulfur bacterium Thiocapsa roseopersicina was examined for photo-autotrophic growth on dimethyl sulfide (DMS). The maximum specific growth rate μ _max (0.068 h⁻¹), saturation constant K _s (38 μm l⁻¹), and yield (5.24 mg protein mmol⁻¹ DMS) were determined in chemostat experiments. Dimethyl sulfoxide was the only product of DMS oxidation. Batch experiments revealed the simultaneous oxidation of DMS and hydrogen sulfide.     

Transient Kinetic Analysis of Hydrogen Sulfide Oxidation Catalyzed by Human Sulfide Quinone Oxidoreductase

The first step in the mitochondrial sulfide oxidation pathway is catalyzed by sulfide quinone oxidoreductase (SQR), which belongs to the family of flavoprotein disulfide oxidoreductases. During the catalytic cycle, the flavin cofactor is intermittently reduced by sulfide and oxidized by ubiquinone, linking H₂S oxidation to the electron transfer chain and to energy metabolism. Human SQR can use multiple thiophilic acceptors, including sulfide, sulfite, and glutathione, to form as products, hydrodisulfide, thiosulfate, and glutathione persulfide, respectively. In this study, we have used transient kinetics to examine the mechanism of the flavin reductive half-reaction and have determined the redox potential of the bound flavin to be −123 ± 7 mV. We observe formation of an unusually intense charge-transfer (CT) complex when the enzyme is exposed to sulfide and unexpectedly, when it is exposed to sulfite. In the canonical reaction, sulfide serves as the sulfur donor and sulfite serves as the acceptor, forming thiosulfate. We show that thiosulfate is also formed when sulfide is added to the sulfite-induced CT intermediate, representing a new mechanism for thiosulfate formation. The CT complex is formed at a kinetically competent rate by reaction with sulfide but not with sulfite. Our study indicates that sulfide addition to the active site disulfide is preferred under normal turnover conditions. However, under pathological conditions when sulfite concentrations are high, sulfite could compete with sulfide for addition to the active site disulfide, leading to attenuation of SQR activity and to an alternate route for thiosulfate formation.     

亚硝酸盐型同步厌氧生物脱氮除硫工艺的运行性能

采用上流式厌氧污泥床(UASB)反应器研究了亚硝酸盐型同步厌氧生物脱氮除硫工艺的性能。该工艺具有很高的硫化物和亚硝酸盐转化潜能,最大容积硫化物去除率和容积硝酸盐去除率分别为13.4kg/(m3·d)和2.3kg/(m3·d);所能耐受的最大进水硫化物和亚硝酸盐浓度分别为880mg/L和252.7mg/L;最适进水硫化物和亚硝酸盐浓度分别为460mg/L和132.3mg/L,最适水力停留时间为4h。硫化物和亚硝酸盐的表观半抑制浓度分别为403.9mg/L和120.8mg/L,两者之间的联合毒性为拮抗作用。     

Adaptation dynamics and evolutionary rescue under sulfide selection in cyanobacteria: a comparative study between Microcystis aeruginosa and Oscillatoria sp. (cyanobacteria)

Experimental evolution studies using cyanobacteria as model organisms are scarce despite the role of cyanobacteria in the evolution of photosynthesis. Three different experimental evolution approaches have been applied to shed light on the sulfide adaptation process, which played a key role in the evolution of this group. We used a Microcystis aeruginosa sulfide‐sensitive strain, unable to grow above ~0.1 mM, and an Oscillatoria sp. strain, isolated from a sulfureous spa (~0.2 mM total sulfide). First, performing a fluctuation analysis design using the spa waters as selective agent, we proved that M. aeruginosa was able to adapt to this sulfide level by rare spontaneous mutations. Second, applying a ratchet protocol, we tested if the limit of adaptation to sulfide of the two taxa was dependent on their initial sulfide tolerance, finding that M. aeruginosa adapted to 0.4 mM sulfide, and Oscillatoria sp. to ~2 mM sulfide, twice it highest tolerance level. Third, using an evolutionary rescue approach, we observed that both speed of exposure to increasing sulfide concentrations (deterioration rate) and populations’ genetic variation determined the survival of M. aeruginosa at lethal sulfide levels, with a higher dependence on genetic diversity. In conclusion, sulfide adaptation of sensitive cyanobacterial strains is possible by rare spontaneous mutations and the adaptation limits depend on the sulfide level present in strain’s original habitat. The high genetic diversity of a sulfide‐sensitive strain, even at fast environmental deterioration rates, could increase its possibility of survival even to a severe sulfide stress.     

Recruitment response of methane-seep macrofauna to sulfide-rich sediments: An in situ experiment

Hydrodynamically unbiased colonization trays were deployed for 6 months (Oct. 2000 to April 2001) on the northern California margin (Eel R. region; 525 m) to examine macrofaunal colonization rates at methane seeps. The influence of sulfide on recruitment and survival was examined by deploying sediments with and without sulfide added; effect of seep proximity was evaluated by placing trays inside and outside seeps. The trays contained a two-layer system mimicking vesicomyid clam bed habitat geochemistry, with 8-9 mM sulfide in a lower agar layer at the start of the experiment. After 6 month on the seabed, the lower agar layer contained 2-4 mM H₂S. We observed rapid macrofaunal colonization equivalent to 50% of initial non-seep ambient densities. There was no difference in total colonizer densities, number of species, or rarefaction diversity among 3 treatments: (1) controls (no sulfide added) placed outside seeps, (2) trays with sulfide added placed outside seeps and (3) trays with sulfide added placed inside seep patches. Colonization trays with sulfide placed at seeps had different species composition from trays without sulfide place outside seeps; there were more amphipods (non-ampeliscid) and cumaceans in the seep/sulfide treatment and more nemerteans, Nephtys cornuta and tanaids in the non-seep/no-sulfide treatment. Outside seeps, annelids comprised < 15% of tray colonists; within seep patches, annelids comprised 5 of the top 10 dominant colonizing taxa (24% of the total). The polychaetes Mediomastus sp., Aphelochaeta sp., Paraonidae sp., and Nerillidae sp. exhibited significantly higher densities in sulfide additions. Tanaids, echinoderms, and N. cornuta exhibited sulfide avoidance. At least 6 dorvilleid polychaete species colonized the experiments. Of these, 4 species occurred exclusively in trays with sulfide added and 80% of all dorvilleid individuals were found in trays with sulfide placed inside seep sediments. Counts of large sulfur bacterial filaments were positively correlated with maximum sulfide concentration in each tray, and with proximity of sulfide to the sediment surface. However, total macrofaunal densities were not correlated with tray sulfide concentrations. As a group, tray assemblages achieved some but not all characteristics of ambient seep assemblages after 6-month exposure on the sea floor. Distinctive colonization patterns at methane seeps contribute to the dynamic mosaic of habitat patches that characterize the eastern Pacific continental margin.Overall, proximity of seep habitats had at least as great an influence on macrofaunal colonization as tray sulfide concentrations. Taxa characteristic of seep sediments were more likely to settle into trays placed inside rather than outside seep patches. Whether this is due to limited dispersal ability or local geochemical cues remains to be determined.     

Sulfide-induced oxygen uptake by isolated spinach chloroplasts catalyzed by photosynthetic electron transport

In addition to an inhibitory effect on the photoreduction of NADP⁺ by isolated spinach chloroplasts ( Spinacea oleracea L. cv. Melody Hybrid), sulfide initiated oxygen uptake by chloroplasts upon illumination, both in presence and absence of an electron acceptor. Sulfide-induced oxygen uptake was sensitive to DCMU demonstrating the involvement of photosynthetic electron transport. Addition of superoxide dismutase to the chloroplast suspension prevented the sulfide-induced oxygen uptake, which indicated that sulfide may be oxidized by the chloroplast, its oxidation being initiated by superoxide formed upon illumination (at the reducing side of PSI). Tris-induced inhibition of NADP⁺ photo-reduction could not be abolished by sulfide, which indicated that sulfide could not act as an electron donor for PSI.     

Analysis of an engineered sulfate reduction pathway and cadmium precipitation on the cell surface

We previously have genetically engineered an aerobic sulfate reduction pathway in Escherichia coli for the generation of hydrogen sulfide and demonstrated the pathway's utility in the precipitation of cadmium. To engineer the pathway, the assimilatory sulfate reduction pathway was modified so that cysteine was overproduced. Excess cysteine was then converted by cysteine desulfhydrase to an abundance of hydrogen sulfide, which then reacted with aqueous cadmium to form cadmium sulfide. In this study, observations of various E. coli clones were combined with an analysis of kinetic and transport phenomena. This analysis revealed that cysteine production is the rate-limiting step in the engineered pathway and provided an explanation for the phenomenon of cell surface precipitation. An analytical model showed that cadmium sulfide must form at the cell surface because the rate of cadmium sulfide formation is extremely fast and the rate of sulfide transport is relatively slow.     

Epidermal ultrastructure and implications for sulfide tolerance in six species of deep-sea polychaetes

Abstract. Ultrastructural characteristics of the epidermis of 5 deep-sea vestimentiferan tube worms and an orbiniid worm were similar to those described from other organisms inhabiting sulfidic environments. The integument was composed of a simple or pseudostratified layer of columnar or cuboidal cells, covered by a cuticle of varying thickness, and rested on an extracellular matrix. Unusual mitochondrial morphology was observed in the peripheral region of the epidermis, characterized by an electron-dense matrix and granules. The abnormal size, shape, and reduced array of cristae in these mitochondria may have resulted from environmental stress. Mitochondria in the inner epidermal layers, where they are more protected from sulfide exposure, displayed normal morphology. The seep vestimentiferans ( Seepiophila jonesi and Lamellibrachia cf. luymesi ) exhibited numerous electron-dense organelles, similar in morphology to cytolysosomes and previously described as sulfide oxidizing bodies, while in the 3 vent vestimentiferans ( Riftia pachyptila, Tevnia jerichonana , and Oasisia alvinae ) and the seep orbiniid Methanoaricia dendrobranchiata , fewer of these organelles were observed. Energy dispersive x-ray microanalysis of these electron-dense organelles indicated the presence of sulfur, iron, zinc, and copper, as well as lesser amounts of other elements. We propose that these epidermal cytolysosomes are morphologically similar to previously described sulfide oxidizing bodies that have been hypothesized to play a role in maintaining aerobically poised animal metabolism in sulfide-enriched habitats.     

基于生物大分子DNA的纳米硫化银的合成

利用DNA生物大分子为模板,硫代乙酰胺和硝酸盐为原料,制备出了颗粒状硫化银纳米结构体。同时采用琼脂糖电泳、FESEM、FTIR和XRD等多种表征手段对其结构组成进行了系统的分析,对其形成机理进行了探讨。     

Development of a novel process for the biological conversion of H2S and methanethiol to elemental sulfur

The feasibility of anaerobic treatment of wastewater containing methanethiol (MT), an extremely volatile and malodorous sulfur compound, was investigated in lab-scale bioreactors. Inoculum biomass originating from full-scale anaerobic wastewater treatment facilities was used. Several sludges, tested for their ability to degrade MT, revealed the presence of organisms capable of metabolizing MT as their sole source of energy. Furthermore, batch tests were executed to gain a better understanding of the inhibition potential of MT. It was found that increasing MT concentrations affected acetotrophic organisms more dramatically than methylotrophic organisms. Continuous reactor experiments, using two lab-scale upflow anaerobic sludge bed (UASB) reactors (R1 and R2), aimed to determine the maximal MT load and the effect of elevated sulfide concentrations on MT conversion. Both reactors were operated at a hydraulic retention time (HRT) of about 7 hours, a temperature of 30 degrees C, and a pH of between 7.3 and 7.6. At the highest influent MT concentration applied, 14 mM in R1, corresponding to a volumetric loading rate of about 50 mM MT per day, 87% of the organic sulfur was recovered as hydrogen sulfide (12.2 mM) and the remainder as volatile organic sulfur compounds (VOSCs). Upon decreasing the HRT to 3.5 to 4.0 h at a constant MT loading rate, the sulfide concentration in the reactor decreased to 8 mM and MT conversion efficiency increased to values near 100%. MT conversion was apparently inhibited by the high sulfide concentrations in the reactor. The specific MT degradation rate, as determined after 120 days of operation in R1, was 2.83 +/- 0.27 mmol MT g VSS(-1) day(-1). During biological desulfurization of liquid hydrocarbon phases, such as with liquefied petroleum gas (LPG), the combined removal of hydrogen sulfide and MT is desired. In R2, the simultaneous addition of sodium sulfide and MT was therefore studied and the effect of elevated sulfide concentrations was investigated. The addition of sodium sulfide resulted in enhanced disintegration of sludge granules, causing significant washout of biomass. Additional acetate, added to stimulate growth of methanogenic bacteria to promote granulation, was hardly converted at the termination of the experimental period.     

Microbiological and environmental variables involved in the sulfide buffering capacity along a eutrophication gradient in a coastal lagoon (Bassin d'Arcachon,France)

Microbiological and environmental variables involved in the removal of free sulfide were studied along an eutrophication transect in the Bassin d'Arcachon (France). At four sites, analyses were carried out on reduced sulfur compounds, iron species and total numbers of viable sulfur bacteria (sulfide-producing bacteria, colorless sulfur bacteria and purple sulfur bacteria). In addition, the chemical buffering capacity towards free sulfide and the potential microbiological sulfide oxidation rates were determined.In the ecosystem, no free sulfide occurs in the top layers of the sediment at all four sites, despite a high nutrient load and hence favourable conditions for sulfide-producing bacteria. The explanation of this apparent discrepancy was shown to be the high biological sulfide oxidizing capacity in combination with a high chemical buffering capacity.The data presented illustrate that the buffering capacity of sediments towards free sulfide is the combined result of the chemical and biological processes. The ratio between these were found to depend on the degree of eutrophication. It was shown that the chemical buffering capacity towards sulfide is severely overestimated when based on the pool of chemically reactive iron, a more realistic value is obtained by estimating the total amount of sulfide that can be added before free sulfide can be detected. A clear difference was observed between the numbers of colorless sulfur bacteria and the activity of the entire population. For a proper quantification of the sulfide buffering capacity of sediments, it is essential to estimate the concentration of iron and sulfur compounds that actually can react with sulfide, as well as to analyze the activities of sulfide-oxidizing microbes.     

Removal of hydrogen sulfide using crushed oyster shell from pore water to remediate organically enriched coastal marine sediments

Hydrogen sulfide is highly toxic and fatal to benthic organisms as well as causing depletion of dissolved oxygen and generating blue tide in eutrophic coastal seas. The purposes of this study are to reveal adsorption characteristics of hydrogen sulfide onto crushed oyster shell, and to evaluate removal efficiency of hydrogen sulfide from pore water in organically enriched sediments using container experiment in order to develop a coastal sediment amendment. The crushed oyster shell was mainly composed of CaCO₃ with calcite and CaO crystal phase. The batch experiment showed removal kinetics of hydrogen sulfide can be expressed as the first order equation and Langmuir plot fitted well in describing the adsorption behavior with the adsorption maximum at 12 mg-S g⁻¹. The container experiments suggested the oyster shell adsorbs hydrogen sulfide in pore water effectively and reduces oxygen consumption in the overlying water. Furthermore, oxidation–reduction potential of the sediment was higher with addition of crushed oyster shell than the control without oyster shell. Thus, it is concluded that crushed oyster shell can be an effective amendment to remediate organically enriched sediments in eutrophic coastal seas.     

Relationship of soil hydrogen sulfide level to net carbon assimilation ofPanicum hemitomon andSpartina patens

Panicum hemitomon Schult andSpartina patens (Ait) Muhl. plants from Louisiana Gulf Coast fresh and brackish marshes were subjected to hydrogen sulfide under controlled sediment redox conditions. Net carbon assimilation responses of both species to the combined sediment anaerobiosis and hydrogen sulfide concentrations was measured.Panicum hemitomon was more sensitive to hydrogen sulfide as compared toSpartina patens. Initiation of reduction in net carbon assimilation inP. hemitomon began when H₂S concentrations of soil solution exceeded 0.22 mgl^-1. Reductions in net carbon assimilation inS. patens were also noted at H₂S concentrations exceeding 0.34 mgl^-1. The reduction in net carbon assimilation of both species measured at elevated H₂S concentrations suggests that extreme anaerobiosis and elevated sulfide could contribute to the growth reduction of these species under certain conditions. However based on H₂S concentration in fresh and brackish marsh soil profiles, levels were too low to cause any adverse effects ofPanicum hemitomon. In brackish marsh soils containing hydrogen sulfide of 3.4 mgl^-1 in soil solution, sulfide could be a major factor limiting growth ofS. patens.