Photovoltaic conversion using Zn chlorophyll derivative assembled in hydrophobic domain onto nanocrystalline TiO2 electrode

Photovoltaic conversion using zinc chlorin-e6 (ZnChl-e6), which is zinc chlorophyll-a derivative, and fatty acid (myristic acid or cholic acid) co-adsorbed nanocrystalline TiO2 layer onto ITO glass (OTE) electrode is developed. The maximum peaks of photocurrent action spectrum of the ZnChl-e6 adsorbed TiO2 layer onto OTE (ZnChl-e6/TiO2) are 400, 660 and 800 nm, respectively. Especially the IPCE value at 800 nm (7.5%) is larger than that of 660 nm (6.9%). This result indicates that ZnChl-e6 molecules is aggregated or formed dimer on a nanocrystalline TiO2 layer onto OTE and the absorption band is shifted to near IR region. The photocurrent action spectrum of ZnChl-e6 and cholic acid adsorbed TiO2 layer onto OTE (ZnChl-e6-Cho/TiO2 is similar to that of the UV-vis absorption spectrum in methanol solution, and IPCE values at 400 and 660 nm (8.1%) increase and the IPCE value at 800 nm (4.1%) decreases, indicating that the aggregation of ZnChl-e6 molecules on the TiO2 is suppressed by cholic acid. By using ZnChl-e6-Cho/TiO2, the short-circuit photocurrent density and open-circuit photovoltage also increase compared with that of ZnChl-e6 adsorbed nanocrystalline TiO2 electrode.     

Photoelectrochemical measurements of a heterosupramolecular system under visible light irradiation.

A photochemical system utilising a modular approach characterised through interpretation of photoelectrochemical measurements is discussed. A photoanode was prepared by the chemisorption of a photosensitiser, cis-bis-(2,2'-bipyridine)-(4,4'-bis-(methyl)phosphonato-2,2'-bipyridine)ruthenium(II) dichloride (RuL2L'2+), to a mixed nanoporous nanocrystalline RuO2:TiO2 thin film, calcined on a fluorine doped SnO2 conducting glass substrate. Similarly, an electron relay molecule, 1-ethyl-1'-(2-phosphonoethyl)-4,4'-bipyridinium dichloride (EVP), was covalently bound to a platinum electroplated nanoporous nanocrystalline TiO2 thin film, and the electrodes connected in a photoelectrocatalytic cell (PCC). Irradiation with lamda > 420 nm gave a measurable photocurrent. Interpretation of the photocurrents obtained from this assembly provides a means for understanding photochemical reactions under low light intensities. Optimised conditions of the electrolyte solution were determined to be pH = 5 and illumination yielded eta = 0.0036% with an apparent quantum yield (AQY)= 1.6%.     

Tuning the optical and photoelectrochemical properties of surface-modified TiO2.

Surface-modification of TiO(2) is found to be a powerful tool for manipulating the fundamental optical and photoelectrochemical properties of TiO(2). High surface area nanocrystalline TiO(2) was modified by urea pyrolysis products at different temperatures between 300 degrees C and 500 degrees C. Modification occurs through incorporation of nitrogen species containing carbon into the surface structure of titania. The N1s XPS binding energies are 399-400 eV and decrease with increasing modification temperature whereby the Ti2p(3/2) peak is also shifted to lower binding energies by about 0.5 eV. With increasing modification temperature the optical bandgap of surface-modified TiO(2) continuously decreases down to approximately 2.1 eV and the quasi-Fermi level of electrons at pH 7 is gradually shifted from -0.6 V to -0.3 V vs. NHE. The surface-modified materials show enhanced sub-bandgap absorption (Urbach tail) and exhibit photocurrents in the visible down to 750 nm. The maximum incident photon-to-current efficiency (IPCE) was observed for the materials modified at 350 degrees C and 400 degrees C (IPCE approximately 14% at 400 nm, and IPCE approximately 1% at 550 nm, respectively). The efficiency of photocurrent generation is limited by surface recombination, which leads to a significant decrease in IPCE values and significantly changes the shape of the IPCE spectra in dependence on the optical bandgap.     

Visible-light-induced patterning of Au- and Ag-TiO2 nanocomposite film surfaces on the basis of plasmon photoelectrochemistry.

A novel technique for patterning based on visible light at Au-TiO2 and Ag-TiO2 nanocomposite film surfaces has been developed for the first time. TiO2 films loaded with Au and Ag nanoparticles were modified with hydrophobic thiols to obtain hydrophobic surfaces. The surfaces were converted to hydrophilic by visible light irradiation. Hydrophobic/hydrophilic patterning was also possible by visible light irradiation through a photomask. The patterning was due to removal of the thiol based on plasmon photoelectrochemistry. Visible-light-induced plasmon resonance at the Au and Ag nanoparticles gives rise to charge separation and redox reactions. The thiol is removed from the Au-TiO2 film probably by oxidative desorption, and from the Ag-TiO2 film owing chiefly to oxidation of Ag nanoparticles to Ag+.     

Enhancement of solar inactivation of Escherichia coli by titanium dioxide photocatalytic oxidation

AIMS: To improve solar water disinfection using a photocatalysing semi-conductor and to study the mechanisms involved in this process. METHODS AND RESULTS: Cells of Escherichia coli were used as the microbiological indicator to study the possibility of improving the efficiency of solar water disinfection using titanium dioxide (TiO2) as a photooxidizing semi-conductor. TiO2 was used either as a suspended powder or in an immobilized form. Both applications improved the efficiency of solar disinfection. TiO2 in suspension was more effective than the immobilized form, producing enhancement factors of 1.62 and 1.34, respectively. The concentration of TiO2 greatly affected efficiency, with a maximum effect at 1 mg ml(-1). Higher TiO2 concentrations reduced the efficiency. Dimethyl sulphoxide (DMSO) and cysteamine (Cys), hydroxyl radical (OH.) scavengers, were used to elucidate the mechanisms involved in the presence of TiO2. Both DMSO and Cys totally abolished the enhancing effect produced by the presence of TiO2. CONCLUSIONS: Sunlight has a potential water disinfecting capacity. The use of TiO2 greatly improved this efficiency. The effect of TiO2 was mainly concentration-dependent, giving maximum efficiency at 1 mg ml(-1). The presence of DMSO and Cys removed the TiO2-induced enhancement, indicating that OH. may be involved in the process of cell killing. SIGNIFICANCE AND IMPACT OF THE STUDY: The efficiency of solar disinfection is limited and time-consuming and needs to be improved. The use of a semi-conductor is promising as it reduces the time of exposure and therefore increases the efficiency of solar disinfection. This would allow for the availability of good quality water, and hence would improve the quality of life.     

Formation spectra of the EPR split signals from the S0, S1, and S3 states in photosystem II induced by monochromatic light at 5 K

The interaction EPR split signals from photosystem II (PSII) have been reported from the S0, S1, and S3 states. The signals are induced by illumination at cryogenic temperatures and are proposed to reflect the magnetic interaction between YZ* and the Mn4Ca cluster. We have investigated the formation spectra of these split EPR signals induced in PSII enriched membranes at 5 K using monochromatic laser light from 400 to 900 nm. We found that the formation spectra of the split S0, split S1, and split S3 EPR signals were quite similar, but not identical, between 400 and 690 nm, with maximum formation at 550 nm. The major deviations were found between 440 and 480 nm and between 580 and 680 nm. In the regions around 460 and 680 nm the amplitudes of the formation spectra were 25-50% of that at 550 nm. A similar formation spectrum was found for the S2-state multiline EPR signal induced at 0 degrees C. In general, the formation spectra of these signals in the visible region resemble the reciprocal of the absorption spectra of our PSII membranes. This reflects the high chlorophyll concentration necessary for the EPR measurements which mask the spectral properties of other absorbing species. No split signal formation was found by the application of infrared laser illumination between 730 and 900 nm from PSII in the S0 and S1 states. However, when such illumination was applied to PSII membranes poised in the S3 state, formation of the split S3 EPR signal was observed with maximum formation at 740 nm. The quantum yield was much less than in the visible region, but the application of intensive illumination at 830 nm resulted in accumulation of the signal to an amplitude comparable to that obtained with illumination with visible light. The split S3 EPR signal induced by NIR light was much more stable at 5 K (no observable decay within 60 min) than the split S3 signal induced by visible light (50% of the signal decayed within 30 min). The split S3 signals induced by each of these light regimes showed the same EPR spectral features and microwave power saturation properties, indicating that illumination of PSII in the S3 state by visible light or by NIR light produces a similar configuration of YZ* and the Mn4Ca cluster.     

Characterization of a dissimilatory-type sulfite reductase, desulfoviridin, from Desulfovibrio africanus Benghazi

A desulfoviridin-type sulfite reductase having the alpha band at 638 nm was purified from Desulfovibrio africanus Benghazi (NCIB 8401) by chromatography on DEAE-cellulose, Sephadex G-200, and DEAE-Sepharose columns and by disc gel electrophoresis. The content of desulfoviridin in the soluble protein was estimated to be about 6% from the purification indexes. Like the typical desulfoviridin from D. vulgaris Miyazaki K, it formed mainly trithionate besides thiosulfate and sulfide in sulfite reduction coupled to hydrogenase and methyl viologen. No significant differences in the amino acid compositions, CD patterns in the UV (205-250 nm) region, and subunit structures were found, except for a pI value about 1 unit larger (pI 5.3). The split Soret (410 +/- 2 nm, less intense peak at 391 +/- 2 nm with a shoulder around 380 nm) and beta (584 +/- 2 nm) band maxima of the enzyme as isolated, and the visible absorption and fluorescence spectra of the acidic acetone-extracted chromophore were almost identical to those ascribed to sirohydrochlorin in spite of the reported difference in the native enzyme (alpha band maxima at 638 nm as against 628 +/- 2 nm in a typical desulfoviridin). Iron was the only significant chelatable metal contained in the chromophore. Some differences between africanus and vulgaris desulfoviridins were observed in the CD patterns in the UV to near UV region (250-340 nm) and also in the visible absorption spectra in the presence of dithionite.     

Surface‐Plasmon Assisted Energy Conversion in Dye‐Sensitized Solar Cells

In this study, the effect of plasmonic core‐shell structures, consisting of dielectric cores and metallic nanoshells, on energy conversion in dye‐sensitized solar cells (DSSCs) is investigated. The structure of the core‐shell particles is controlled to couple with visible light so that the visible component of the solar spectrum is amplified near the core‐shell particles. In core‐shell particle – TiO₂ nanoparticle films, the local field intensity and light pathways are increased due to the surface plasmons and light scattering. This, in turn, enlarges the optical cross‐section of dye sensitizers coated onto the mixed films. When 22 vol% of core‐shell particles are added to a 5 μm thick TiO₂ film, the energy conversion efficiency of DSSCs increases from 2.7% to 4.0%, in spite of a more than 20% decrease in the amount of dyes adsorbed on the composite films. The correlation between core‐shell particle content and energy conversion efficiency in DSSCs is explained by the balance among near‐field effects, light scattering efficiency, and surface area in the composite films.     

Plasmon-Enhanced Light Trapping to Improve Efficiency of TiO2 Nanorod-Based Dye-Sensitized Solar Cell

Localized surface plasmon resonance incurred by silver nanoparticles is used to enhance the photoelectric conversion efficiency of a TiO₂ nanorod-based dye-sensitized solar cell (DSSC). Improved light transmission is observed experimentally in silver nanoparticle-coated FTO glass. The transmission data are used to explore the effect on electrical parameters of DSSC using theoretical model. Current density increased from 11.7 to 12.34 mA/cm² and open-circuit voltage increased from 704 to 709.5 mV. Overall efficiency enhancement of 6.67 % is observed in TiO₂ nanorod-based DSSC due to plasmon-induced light trapping.     

可见光响应的CdTe/TiO2复合纳米颗粒体外PDT灭活HL60细胞的研究

文章采用溶胶凝胶法制备核壳CdTe/TiO_2复合纳米颗粒,探讨了该复合纳米颗粒体外PDT对HL60细胞的灭活作用。通过扫描电镜(TEM)、X射线光电子衍射仪(XPS)对CdTe/TiO_2进行表征。文中,用紫外可见光吸收光谱(UV-vis)测得尺寸为2-5 nm的CdTe QDs吸收峰为460 nm。研究表明,CdTe/TiO_2复合纳米颗粒尺寸在80 nm左右,其吸收光谱相较于TiO_2的光响应区拓展至可见光区。将CdTe/TiO_2与HL60细胞进行共同孵育,采用CCK-8法研究了其在暗室条件下细胞的生长情况和浓度对细胞相对存活率的影响以及在不同浓度的CdTe/TiO_2复合纳米颗粒PDT后的细胞活性。实验结果表明:在共同孵育16 h后CdTe/TiO_2对HL60细胞的毒性最强,10~320μg/mL浓度的CdTe/TiO_2样品对HL60细胞均具有较强的灭活作用。当添加CdTe/TiO_2样品浓度为320μg/mL时,光照1 h后PDT灭活效率达到87.7%。     

High-intensity narrow-spectrum light inactivation and wavelength sensitivity of Staphylococcus aureus

This study was conducted to investigate the bactericidal effects of visible light on methicillin-sensitive and methicillin-resistant Staphylococcus aureus (MRSA), and subsequently identify the wavelength sensitivity of S. aureus, in order to establish the wavelengths inducing maximum inactivation. Staphylococcus aureus, including MRSA strains, were shown to be inactivated by exposure to high-intensity visible light, and, more specifically, through a series of studies using a xenon broadband white-light source in conjunction with a selection of optical filters, it was found that inactivation of S. aureus occurs upon exposure to blue light of wavelengths between 400 and 420 nm, with maximum inactivation occurring at 405+/-5 nm. This visible-light inactivation was achieved without the addition of exogenous photosensitisers. The significant safety benefit of these blue-light wavelengths over UV light, in addition to their ability to inactivate medically important microorganisms such as MRSA, emphasises the potential of exploiting these non-UV wavelengths for disinfection applications.     

Nitrogenase from Azotobacter chroococcum. Purification and properties of the component proteins.

1. A large-scale purification of the nitrogenase components from Azotobacter chroococcum yielded two non-haem iron proteins, both of which were necessary for nitrogenase activity and each had a specific activity of approximately 2000 +/- 300 nmol of acetylene reduced/mg protein per min in the presence of sautrating amounts of the other. This procedure freed the Mo-Fe protein from a protein contaminant which had an electron paramagnetic resonance signal at g = 1.94. 2. Both proteins were purified to homogeneity as determined by disc gel electrophoresis and ultracentrifugal analysis. Both proteins were oxygen-sensitive but not cold-labile. Ultracentrifugal analysis indicated that both proteins dissociated to a slight degree at concentrations below 2 mg/ml. 3. The larger of the two proteins had a molecular weight of 227 000 and contained 1.9 +/- 0.3 atoms of Mo, 23 +/- 2 atoms of Fe, 20 +/- 2 acid-labile sulphide and 47 tryptophan residues/mol. The protein consists of 4 subunits of mol. wt 60 000 (approx.). The reduced protein showed electron paramagmetic resonance signals at g = 4.29, 3.65 and 2.013 but not in the area of g = 5 to 6. Upon oxidation abosrbance increased throughout the visible region of the ultraviolet visible spectrum, with a maximum difference between oxidised and reduced protein occurring at 430 nm. 4. The smaller protein had a molecular weight of 64 000 and contained 4 g-atoms of Fe and 4 acid-labile sulphide groups/mol but no tryptophan. It had two subunits of mol. wt 30 800. The reduced protein showed electron paramagnetic resonance signhe protein retained almost full activity after oxidation with phenazine methosulphate. The ultraviolet visible spectrum of oxidised protein was clearly different from that of the oxygen-inactivated protein: it had a sharp peak at 269 nm and a broad absorbance between 340 and 470 nm with a maximum difference between oxidised and reduced forms at 430 nm. Oxygen-inactivated protein showed a sharp peak at 277.5 nm and broad peaks from 305 to 360, 400 to 425 and 435 to 475 nm. 5. Amino acid analyses of both proteins showed that most common amino acids were present with a preponderance of acidic residues. Analyses of compositional relatedness showed that the nitrogenase proteins from A. chroococcum were most closely related to those from A. vinelandii and least so to those from Clostridium pasteurianum.     

Pure red upconverted and near-infrared luminescence properties of Er3+-doped SnO2 nanocrystals for lighting applications

Tin oxide (SnO₂) nanocrystalline powders doped with erbium ion (Er³⁺) in different molar ratios (0, 3, 5, and 7 mol%) were prepared using a solid-state reaction technique. These samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet-visible absorption, visible upconversion, and near-infrared luminescence techniques. XRD analysis revealed the tetragonal rutile structure of SnO₂ and the average crystallite size was about 32 nm. From Tauc's plots, it was confirmed that the substitution of Er³⁺ ions into the SnO₂ host lattice resulted in the narrowing its band gap. Optical absorption bands at 520 and 654 nm correspond to the 4f electron transitions of Er³⁺ further confirming visible light absorption. Infrared luminescence spectra showed a broad band centred at 1536 nm which is assigned to the ⁴I_13/2 → ⁴I_15/2 transition of Er³⁺. Visible upconverted emission spectra under 980 nm excitation exhibit a strong red luminescence with a main peak at 672 nm which is attributed to the ⁴F_9/2 → ⁴I_15/2 transition of Er³⁺. Power-dependent upconversion spectra confirmed that two photons participated in the upconversion mechanism. Enhancement in the intensities of both visible and infrared luminescence was observed when raising the concentration. The results pave the way for the potential applications of these nanocrystalline powders in energy harvesting applications such as infrared light upconverting layer in solar cells, light emitting diodes, infrared broadband sources and amplifiers, and biological labelling.     

Isolation, characterization and oxygen equilibrium of an extracellular haemoglobin from Eunice aphroditois (Passas).

The extracellular haemoglobin from the polychaeta,Eunice aphroditois, existed as a mixture of a heavy major component (so20, w = 56.96 +/- 0.125) and a light minor component (so20, w = 10.00 +/- 0.13S), the latter probably being a dissociation product of the former. The molecular weight of the purified heavier component, as detetermined by sedimentation equilibrium, was 3.44 x 10(6) +/- 0.04x10(6). The molecule had the electron-microscopic appearance typical of annelid haemoglobins, consisting of a stack of two hexagonal plates, with dimensions 26.32 +/- 0.27 nm across the flats of the hexagon, height of stack 17.86 +/- 0.34 nm. The sugar composition is reported, and the isoelectric point was approx. pH7.8. The haem content was 2.31 +/- 0.01%, corresponding to a minimal mol.wt. of 26700. Detergent/gel electrophoresis revealed the presence of at least four bands with molecular weights in the range 14600-31000. Five N-terminal amino acids were found. In addition to the 10S component, which co-existed with the 57S component at all pH values in the range 4.0-10.6, at low pH values (less than pH.5.0) A 16S and a 1.9 S component were found. The absorption and circular-dichroic spectra are reported, and the alpha-helical content, calculated from the ellipticity at 222 nm, was about 40%. The molecule bound O2 co-operatively with a maximum value of the Hill coefficient, h, of 3.9. Over the pH range 7.0-8.0 there was a positive Bohr effect.     

Photoelectrochemical biofuel cell using porphyrin-sensitized nanocrystalline titanium dioxide mesoporous film as photoanode

Electrical energy generated directly from sunlight and biomass solution with a Photoelectrochemical Biofuel Cell (PEBFC) was investigated. The PEBFC consisted of a meso-tetrakis(4-carboxyphenyl)porphyrin (TCPP)-sensitized nanocrystalline titanium dioxide (TiO(2)) mesoporous film (NTDMF) as the photoanode and platinum black as the cathode. The interaction between TCPP sensitizer and NTDMF was evaluated by X-ray photoelectron spectra and FT-IR absorption spectra, indicating that the TCPP sensitizer was adsorbed on the NTDMF by bridging or bidentate coordinate bonds. The spectroscopic properties of pure TCPP ethanol solution and TCPP-sensitized NTDMF were obtained by UV-vis absorption spectra, demonstrating that the characteristic absorption peaks of TCPP on NTDMF displayed slight red shift compared with pure TCPP ethanol solution. The performances of the PEBFC were obtained by photocurrent-photovoltage characteristic curves. The open-circuit photovoltage (V(oc)), the short-circuit photocurrent (I(sc)) and the maximum power density (P(max)) was 0.74 V, 69.96 μA and 33.94 μWcm(-2) at 0.45 V, respectively. The fill factor (FF) was 0.19 and the incident photo-to-current efficiency (IPCE) was 36.0% at 436 nm. The results demonstrated that the TCPP was an appropriate photosensitizer for PEBFC.     

Coupling of cytochrome and quinone turnovers in the photocycle of reaction centers from the photosynthetic bacterium Rhodobacter sphaeroides.

A minimal kinetic model of the photocycle, including both quinone (Q-6) reduction at the secondary quinone-binding site and (mammalian) cytochrome c oxidation at the cytochrome docking site of isolated reaction centers from photosynthetic purple bacteria Rhodobacter sphaeroides, was elaborated and tested by cytochrome photooxidation under strong continuous illumination. The typical rate of photochemical excitation by a laser diode at 810 nm was 2.200 s-1, and the rates of stationary turnover of the reaction center (one-half of that of cytochrome photooxidation) were 600 +/- 70 s-1 at pH 6 and 400 +/- 50 s-1 at pH 8. The rate of turnover showed strong pH dependence, indicating the contribution of different rate-limiting processes. The kinetic limitation of the photocycle was attributed to the turnover of the cytochrome c binding site (pH < 6), light intensity and quinone/quinol exchange (6 < pH < 8), and proton-coupled second electron transfer in the quinone acceptor complex (pH > 8). The analysis of the double-reciprocal plot of the rate of turnover versus light intensity has proved useful in determining the light-independent (maximum) turnover rate of the reaction center (445 +/- 50 s-1 at pH 7.8).     

Multifunctional Luminescent Down‐Shifting Fluoropolymer Coatings: A Straightforward Strategy to Improve the UV‐Light Harvesting Ability and Long‐Term Outdoor Stability of Organic Dye‐Sensitized Solar Cells

A new multifunctional coating for photovoltaic cells incorporating light‐management, UV‐protection, and easy‐cleaning capabilities is presented. Such coating consists of a new photocurable fluorinated polymer embedding a luminescent europium complex that acts as luminescent down‐shifting (LDS) material converting UV photons into visible light. The combination of this system with ruthenium‐free organic dye‐sensitized solar cells (DSSCs) gives a 70% relative increase in power conversion efficiency as compared with control uncoated devices, which is the highest efficiency enhancement reported to date on organic DSSC systems by means of a polymeric LDS layer. Long‐term (>2000 h) weathering tests in real outdoor conditions reveal the excellent stabilizing effect of the new coating on DSSC devices, which fully preserve their initial performance. This excellent outdoor stability is attributed to the combined action of the luminescent material that acts as UV‐screen and the highly photostable, hydrophobic fluoropolymeric carrier that further prevents photochemical and physical degradation of the solar cell components. The straightforward approach presented to simultaneously improve performance and outdoor stability of DSSC devices may be readily extended to a large variety of sensitizer/luminophore combinations, thus enabling the fabrication of highly efficient and extremely stable DSSCs in an easy and versatile fashion.     

Direct electrical power generation from urine, wastes and biomass with simultaneous photodecomposition and cleaning

Electric power was for the first time generated directly from urine, wastes, and biomass with simultaneous photodecomposition and cleaning by using a biophotofuel cell (BPFC) composed of a nanoporous TiO2 film semiconductor photoanode and an O2-reducing cathode. Human urine exhibited a PFC characteristics with J(sc) 0.086 mA cm(-2), Voc 0.56 V, and fill factor (FF) 0.50 under irradiation by a solar simulator with AM 1.5 G and 100 mW cm(-2) incident light intensity. Both the soluble and residual parts of waste paper partially solubilized by a H3PO4 aqueous solution were also photodecomposed with simultaneous electrical power generation. As trials of various biomass materials, Coca-Cola (to test colored sample), Japanese rice wine (to test alcohol aqueous solution), and grated radish (to test slurry state sample) also generated effectively electrical power during photodecomposition by a solar simulator.     

Biochemical characterization and solution structure of nitrous oxide reductase from Alcaligenes xylosoxidans (NCIMB 11015).

Nitrous oxide reductase (N2OR) is the terminal enzyme involved in denitrification by microbes. No three-dimensional structural information has been published for this enzyme. We have isolated and characterised N2OR from Alcaligenes xylosoxidans (AxN2OR) as a homodimer of M(r) 134,000 containing seven to eight copper atoms per dimer. Comparison of sequence and compositional data with other N2ORs suggests that AxN2OR is typical and can be expected to have similar domain folding and subunit structure to other members of this family of enzymes. We present synchrotron X-ray-scattering data, analysed using a model-independent method for shape restoration, which gave a approximately 20 A resolution structure of the enzyme in solution, providing a glimpse of the structure of any N2OR and shedding light on the molecular architecture of the molecule. The specific activity of AxN2OR was approximately 6 mumol of N2O reduced.min-1. (mg of protein)-1; N2OR activity showed both base and temperature activation. The visible spectrum exhibited an absorption maximum at 550 nm with a shoulder at 635 nm. On oxidation with K3Fe(CN)6, the absorption maximum shifted to 540 nm and a new shoulder at 480 nm appeared. Reduction under anaerobic conditions resulted in the formation of an inactive blue form of the enzyme with a broad absorption maximum at 650 nm. As isolated, the enzyme shows an almost featureless EPR spectrum, which changes on oxidation to give an almost completely resolved seven-line hyperfine signal in the gII region, g = 2.18, with AII = 40 G, consistent with the enzyme being partially reduced as isolated. Both the optical and EPR spectra of the oxidized enzyme are characteristic of the presence of a CuA centre.