Kinetics of kojic acid fermentation byAspergillus flavus link S44-1 using sucrose as a carbon source under different pH conditions

Kojic acid production byAspergillus flavus strain S44-1 using sucrose as a carbon source was carried out in a 250-mL shake flask and a 2-L stirred tank fermenter. For comparison, production of kojic acid using glucose, fructose and its mixture was also carried out. Kojic acid production in shake flask fermentation was 25.8 g/L using glucose as the sole carbon source, 23.6 g/L with sucrose, and 6.4 g/L from fructose. Reduced kojic acid production (13.5 g/L) was observed when a combination of glucose and fructose was used as a carbon source. The highest production of kojic acid (40.2 g/L) was obtained from 150 g/L sucrose in a 2 L fermenter, while the lowest kojic acid production (10.3 g/L) was seen in fermentation using fructose as the sole carbon source. The experimental data from batch fermentation and resuspended cell system was analysed in order to form the basis for a kinetic model of the process. An unstructured model based on logistic and Luedeking-Piret equations was found suitable to describe the growth, substrate consumption, and efficiency of kojic acid production byA. flavus in batch fermentation using sucrose. From this model, it was found that kojic acid production byA. flavus was not a growth-associated process. Fermentation without pH control (from an initial culture pH of 3.0) showed higher kojic acid production than single-phase pH-controlled fermentation (pH 2.5, 2.75, and 3.0).     

Kojic acid production byAspergillus flavus using gelatinized and hydrolyzed sago starch as carbon sources

Direct conversion of gelatinized sago starch into kojic acid byAspergillus flavus strain having amylolytic enzymes was carried out at two different scales of submerged batch fermentation in a 250-mL shake flask and in a 50-L stirred-tank fermentor. For comparison, fermentations were also carried out using glucose and glucose hydrolyzate from enzymic hydrolysis of sago starch as carbon sources. During kojic acid fermentation of starch, starch was first hydrolyzed to glucose by the action of α-amylase and glucoamylase during active growth phase. The glucose remaining during the production phase (non-growing phase) was then converted to kojic acid. Kojic acid production (23.5g/L) using 100 g/L sago starch in a shake flask was comparable to fermentation of glucose (31.5 g/L) and glucose hydrolyzate (27.9 g/L) but in the 50-L fermentor was greatly reduced due to non-optimal aeration conditions. Kojic acid production using glucose was higher in the 50-L fermentor than in the shake flask.     

Production of poly(4-hydroxybutyric acid) by fed-batch cultures of recombinant strains of Escherichia coli

A recombinant strain of Escherichia coli was used to produce poly(4-hydroxybutyric acid), P(4HB), homopolyester by fed-batch culture in M9 mineral salts medium containing glucose and 4-hydroxybutyric acid as carbon sources. The final cell dry weight, P(4HB) concentration and P(4HB) content were 12.6 g/l, 4.4 g/l, and 36% of cell dry weight, respectively, in a 27-l stirred and aerated fermenter after 60 h of fed-batch fermentation at constant pH.     

Kinetics of kojic acid fermentation by Aspergillus flavus using different types and concentrations of carbon and nitrogen sources

Kinetics of kojic acid fermentation by Aspergillus flavus Link 44-1 using various sources of carbon [glucose, xylose, sucrose, starch, maltose, lactose or fructose] and nitrogen [NH₄Cl, (NH₄)₂S₂O₈, (NH₄)₂NO₃, yeast extract or peptone] were analyzed using models based on logistic and Luedeking–Piret equations. The highest kojic acid production (39.90 g l⁻¹) in submerged batch fermentation was obtained when 100 g l⁻¹ glucose was used as a carbon source. Organic nitrogen sources such as peptone and yeast extract were favorable for kojic acid production as compared to inorganic nitrogen sources. Yeast extract at 5 g l⁻¹ was optimal. The optimal carbon to nitrogen (C/N) ratio for kojic acid fermentation was 93.3. In a resuspended cell system, the rate of glucose conversion to kojic acid by cell-bound enzymes increased with increasing glucose concentration up to 70 g l⁻¹, suggesting that the reaction followed the Michaelis–Menten enzyme kinetic model. The value of K _m and V _max for the reaction was 18.47 g l⁻¹ glucose and 0.154 g l⁻¹ h⁻¹, respectively. Journal of Industrial Microbiology & Biotechnology (2000) 25, 20–24. Received 13 October 1999/ Accepted in revised form 02 April 2000     

Cell reuse in submerged lactic acid batch fermentation

The reusability of biomass in lactic acid batch fermentation with free cells of Lactobacillus paracasei was studied in a 2–1 fermenter and in a 50-1 fermenter. In lab-scale fermentation experiments, 33 to 100% of the cell mass formed was reused in the subsequent batch in each case. In a series of seven consecutive batches, maximum values of lactate formation productivity of 6.32 to 11.54 g/l × h were observed at initial cell concentrations of 2.1 to 24.6 g/l. In all of the experiments, the initial cell viability was 78% or greater than 78%, and the final cell viability did not fall below 70%. At cell concentrations above 20 g/l, the productivity of lactic acid formation did not increase further, but remained constant. Because its level could be influenced by varying the proportions between the content of yeast extract, peptone and initial cell mass (1:1:2, 1:1:1 and 3.3.1) in the medium and no inhibitory effects were observed, this finding can be attributed to nutrient limitation. A low degree of cell reuse was reached in an analogous series of experiments carried out in a 50-1 fermenter. In this case, the initial cell concentration varied between 0.5 and 1.1 g/l, and therefore cell growth was not limited by nutrients in the first period of fermentation. Lactate production was still stable after six cell-reuse operations. The lactic acid yield did not fall below 90%. Temporary storage of the biomass in a refrigerator for a time interval of one to two weeks caused no significant impairment of overall lactate production, but a proportional prolongation of the lag phase occurred with increasing duration of storage.     

Improvement of kojic acid production in Aspergillus oryzae B008 mutant strain and its uses in fermentation of concentrated corn stalk hydrolysate

A strain designated M866, producing kojic acid with a high yield, was obtained by combining induced mutation using ion beam implantation and ethyl methane sulfonate treatment of a wild type strain of Aspergillus oryzae B008. The amount of kojic acid produced by the strain M866 in a shaking flask was 40.2 g/L from 100 g/L of glucose, which was 1.7 times higher than that produced by wild strain (23.58 g/L). When the mixture of glucose and xylose was used as carbon source, the resulting kojic acid production was raised with the increasing of glucose ratios in the mixture. With concentrations of glucose at 75 g/L and xylose at 25 g/L mixed in the medium, the production of kojic acid reached 90.8 %, which was slightly lower than with glucose as the sole source of carbon. In addition, the kojic acid fermentation of the concentrated hydrolysate from corn stalk was also investigated in this study, the maximum concentration of kojic acid accumulated at the end of the fermentation was 33.1 g/L and this represents the yield based on reducing sugar consumed and the overall productivity of 0.36 g/g and 0.17 g/L/h, respectively.     

Ethanol fermentation in an immobilized cell reactor using Saccharomyces cerevisiae

Fermentation of sugar by Saccharomyces cerevisiae, for production of ethanol in an immobilized cell reactor (ICR) was successfully carried out to improve the performance of the fermentation process. The fermentation set-up was comprised of a column packed with beads of immobilized cells. The immobilization of S. cerevisiae was simply performed by the enriched cells cultured media harvested at exponential growth phase. The fixed cell loaded ICR was carried out at initial stage of operation and the cell was entrapped by calcium alginate. The production of ethanol was steady after 24 h of operation. The concentration of ethanol was affected by the media flow rates and residence time distribution from 2 to 7 h. In addition, batch fermentation was carried out with 50 g/l glucose concentration. Subsequently, the ethanol productions and the reactor productivities of batch fermentation and immobilized cells were compared. In batch fermentation, sugar consumption and ethanol production obtained were 99.6% and 12.5% v/v after 27 h while in the ICR, 88.2% and 16.7% v/v were obtained with 6 h retention time. Nearly 5% ethanol production was achieved with high glucose concentration (150 g/l) at 6 h retention time. A yield of 38% was obtained with 150 g/l glucose. The yield was improved approximately 27% on ICR and a 24 h fermentation time was reduced to 7 h. The cell growth rate was based on the Monod rate equation. The kinetic constants (K(s) and mu(m)) of batch fermentation were 2.3 g/l and 0.35 g/lh, respectively. The maximum yield of biomass on substrate (Y(X-S)) and the maximum yield of product on substrate (Y(P-S)) in batch fermentations were 50.8% and 31.2% respectively. Productivity of the ICR were 1.3, 2.3, and 2.8 g/lh for 25, 35, 50 g/l of glucose concentration, respectively. The productivity of ethanol in batch fermentation with 50 g/l glucose was calculated as 0.29 g/lh. Maximum production of ethanol in ICR when compared to batch reactor has shown to increase approximately 10-fold. The performance of the two reactors was compared and a respective rate model was proposed. The present research has shown that high sugar concentration (150 g/l) in the ICR column was successfully converted to ethanol. The achieved results in ICR with high substrate concentration are promising for scale up operation. The proposed model can be used to design a lager scale ICR column for production of high ethanol concentration.     

Enhancement of 5-aminolevulinate production with recombinant Escherichia coli using batch and fed-batch culture system

5-Aminolevulinate (ALA) production with recombinant Escherichia coli Rosetta (DE3)/pET28a(+)-hemA was studied. In batch fermentation, the addition of glucose and glycine was effective to improve ALA production. Then the fed-batch fermentation was conducted with continuous feeding of precursors. When the concentrations of succinic acid and glycine were 7.0 g/l and 4.0 g/l, respectively, in the feeding, the ALA yield reached 4.1g/l. But the molar yield (ALA/glycine) was decreased in the fed-batch fermentation compared to batch fermentation. And it was found that the pH control during fed-batch cultivation was very important for the cell growth and ALA production. A two-stage pH value controlling strategy was suggested, in which, the pH value in the first 6h was regulated at pH 5.9, after then at pH 6.2, and the ALA yield was as high as 6.6g/l via fed-batch fermentation.     

Low-cost propionate salt as road deicer: evaluation of cheese whey and other media constituents

Propionate and acetate salts are environmentally friendly, effective road deicer substitutes for widely used sodium chloride. A low-cost medium, using raw cheese whey and hydrolyzed whey permeate/whey permeate powder as substrates, and corn-steep liquor as a nutrient supplement, was studied for lactic acid production, replacing synthetic lactose and other high-cost nutrients. A non-sterile stage-I fermentation process for improved lactate productivity using an inexpensive commercial medium was performed at a 20-L fermenter level. A lactate yield of 0.98 g/g lactose and a productivity of 1.1 g/L/h was obtained with complete lactose utilization. When synthetic lactate and glucose were used as substrates in propionate and acetate fermentation, a total acid yield of 0.55 g/g glucose and lactate consumed and a batch productivity of 0.22 g/L/h was obtained. A stage-II fermentation process to produce propionate and acetate salts from cheese whey-derived lactate (stage-I fermentation broth) resulted in 1.6%( w/v) propionate after a total of 161 h (stages I and II).     

Production of carbonyl reductase by Geotrichum candidum in a laboratory scale bioreactor

Fungal fermentation is very complex in nature due to its nonlinear relationship with the time, especially in batch culture. Growth and production of carbonyl reductase by Geotrichum candidum NCIM 980 have been studied in a laboratory scale stirred tank bioreactor at different pH (uncontrolled and controlled), agitation, aeration and dissolved oxygen concentration. The yield of the process has been calculated in terms of glucose consumed. Initial studies showed that fermenter grown cells have more than 15 times higher activity than that of the shake flask grown cells. The medium pH was found to have unspecific but significant influence on the enzyme productivity. However, at controlled pH 5.5 the specific enzyme activity was highest (306U/mg). Higher agitation had detrimental effect on the cell mass production. Dissolved oxygen concentration was maintained by automatic control of the agitation speed at an aeration rate of 0.6 volume per volume per minute (vvm). Optimization of glucose concentration yielded 21g/l cell mass with and 9.77x10(3)U carbonyl reductase activity/g glucose. Adaptation of different strategies for glucose feeding in the fermenter broth was helpful in increasing the process yield. Feeding of glucose at a continuous rate after 3h of cultivation yielded 0.97g cell mass/g glucose corresponding to 29.1g/l cell mass. Volumetric oxygen transfer coefficient (K(L)a) increased with the increasing of agitation rate.     

Continuous Fermentation in high flow rate fermenter systems

In commercial batch processes the productivity of product formation is low. But a significant increase of productivity can be achieved in continuous fermentations. By using high flow rate fermenter systems characterized by a relatively long retention time of biomass in comparison with the retention time of the liquid we can realize a high-performance fermentation. The problem of holding back the biomass within the reactor could be solved by means of membranes being impenetrable to the cells, but permeable to the hydraulic phase. Such a process technology was successfully tested for its applicability in alcoholic and lactic acid fermentations. The maximum productivities obtained on this way were ? = 120 g/l. · h for ethanol production and ? = 51 g/l. h for lactic acid fermentation, respectively.     

Repeated-batch production of kojic acid in a cell-retention fermenter using Aspergillus oryzae M3B9

A cell-retention fermenter was used for the pilot-scale production of kojic acid using an improved strain of Aspergillus oryzae in repeated-batch fermentations. Among the various carbon and nitrogen sources used, sucrose and yeast extract promoted pellet morphology of fungi and higher kojic acid production. Repeated-batch culture using a medium replacement ratio of 75% gave a productivity of 5.3 g L^–1 day^–1 after 11.5 days of cultivation. While batch culture in shake-flasks resulted in a productivity of 5.1 g L^–1 day^–1, a productivity of 5 g L^–1 day^–1 was obtained in a pilot-scale fermenter. By converting the batch culture into repeated batches, the non-productive downtime of cleaning, filling and sterilizing the fermenter between each batch were eliminated, thereby increasing the kojic acid productivity.     

Continuous gluconic acid production by isolated yeast-like mould strains of <Emphasis Type="Italic">Aureobasidium pullulans</Emphasis>

By extensive microbial screening, about 50 strains with the ability to secrete gluconic acid were isolated from wild flowers. The strains belong to the yeast-like mould Aureobasidium pullulans (de Bary) Arnaud. In shake flask experiments, gluconic acid concentrations between 23 and 140 g/l were produced within 2 days using a mineral medium. In batch experiments, various important fermentation parameters influencing gluconic acid production by A. pullulans isolate 70 (DSM 7085) were identified. Continuous production of gluconic acid with free-growing cells of the isolated yeast-like microorganisms was studied. About 260 g/l gluconic acid at total glucose conversion could be achieved using continuous stirred tank reactors in defined media with residence times (RT) of about 26 h. The highest space-time-yield of 19.3 g l(-1) x h(-1)) with a gluconic acid concentration of 207.5 g/l was achieved with a RT of 10.8 h. The possibility of gluconic acid production with biomass retention by immobilised cells on porous sinter glass is discussed. The new continuous gluconate fermentation process provides significant advantages over traditional discontinuous operation employing Aspergillus niger. The aim of this work was the development of a continuous fermentation process for the production of gluconic acid. Process control becomes easier, offering constant product quality and quantity.     

Optimisation of media and cultivation conditions for L(+)(S)-lactic acid production by Lactobacillus casei NRRL B-441

Process variables and concentration of carbon in media were optimised for lactic acid production by Lactobacillus casei NRRL B-441. Lactic acid yield was inversely proportional to initial glucose concentration within the experimental area (80-160 g l(-1)). The highest lactic acid concentration in batch fermentation, 118.6 g l(-1), was obtained with 160 g 1(-1) glucose. The maximum volumetric productivity, 4.4 g 1(-1) h(-1) at 15 h, was achieved at an initial glucose concentration of 100 g l(-1). Similar lactic acid concentrations were reached with a fedbatch approach using growing cells, in which case the fermentation time was much shorter. Statistical experimental design and response surface methodology were used for optimising the process variables. The temperature and pH optima for lactic acid production were 35 degrees C, pH 6.3. Malt sprout extract supplemented with yeast extract (4 g l(-1)) appeared to be an economical alternative to yeast extract alone (22 g l(-1)) although the fermentation time was a little longer. The results demonstrated both the separation of the growth and lactic acid production phases and lactic acid production by non-growing cells without any nutrient supplements. Resting L. casei cells converted 120 g l(-1) glucose to lactic acid with 100% yield and a maximum volumetric productivity of 3.5 g l(-1) h(-1).     

Isolation of a kojic acid-producing fungus capable of using starch as a carbon source

A fungal strain (S33-2), able to grow on cooked starch and produce a substantially high level of kojic acid, was isolated from morning glory flower ( Bixa orellana ). The fungus was characterized and identified as Aspergillus flavus. The effect of different types of starch (sago, potato and corn starch) on growth of strain S33-2 and kojic acid production was examined using shake flasks. It was found that strain S33-2 grew well on all types of starch investigated. However, kojic acid production was highest when corn starch was used, with the maximum kojic acid obtained being comparable to fermentation using glucose. The highest kojic acid production (19·2 g l⁻¹) was obtained when 75 g l⁻¹ corn starch was used. This gave a yield, based on starch consumed, and an overall productivity of 0·256 g g⁻¹ and 0·04 g l⁻¹ h⁻¹, respectively.     

Study of mycelial growth and bioactive polysaccharide production in batch and fed-batch culture of Grifola frondosa

The fermentation of Grifola frondosa was investigated in the shake flasks and a 5-L jar fermenter in batch and fed-batch modes. In the shake-flask experiments, the preferable mycelial growth and exopolysaccharide (EPS) production was observed at relatively low pH; maltose and glucose were preferred carbon sources for high mycelial production. The EPS was doubled after 13 d of cultivation when glucose was increased from 2% to 4%. Yeast extract (YE) (0.4%) in combination with corn steep powder (CSP) (0.6%) and YE (0.8%) in combination with CSP (1.2%) were preferred nitrogen sources for high mycelial production and EPS production, respectively. All plant oils tested significantly stimulate cell growth of G. frondosa but they failed to enhance EPS production. The EPS products usually consisted of two fractions of different molecular sizes varied by the plant oils used. The fed-batch fermentation by glucose feeding was performed when the glucose concentration in the medium was lower than 0.5% (5g/L), which greatly enhanced the accumulation of mycelial biomass and EPS; the mycelial biomass and EPS were 3.97g/L and 1.04g/L before glucose feeding, which reached 8.23g/L and 3.88g/L at 13 d of cultivation. In contrast, the mycelial biomass and EPS in the batch fermentation were 6.7g/L and 3.3g/L at 13 d of cultivation.     

Multi-stage high cell continuous fermentation for high productivity and titer

We carried out the first simulation on multi-stage continuous high cell density culture (MSC-HCDC) to show that the MSC-HCDC can achieve batch/fed-batch product titer with much higher productivity to the fed-batch productivity using published fermentation kinetics of lactic acid, penicillin and ethanol. The system under consideration consists of n-serially connected continuous stirred-tank reactors (CSTRs) with either hollow fiber cell recycling or cell immobilization for high cell-density culture. In each CSTR substrate supply and product removal are possible. Penicillin production is severely limited by glucose metabolite repression that requires multi-CSTR glucose feeding. An 8-stage C-HCDC lactic acid fermentation resulted in 212.9 g/L of titer and 10.6 g/L/h of productivity, corresponding to 101 and 429% of the comparable lactic acid fed-batch, respectively. The penicillin production model predicted 149% (0.085 g/L/h) of productivity in 8-stage C-HCDC with 40 g/L of cell density and 289% of productivity (0.165 g/L/h) in 7-stage C-HCDC with 60 g/L of cell density compared with referring batch cultivations. A 2-stage C-HCDC ethanol experimental run showed 107% titer and 257% productivity of the batch system having 88.8 g/L of titer and 3.7 g/L/h of productivity. MSC-HCDC can give much higher productivity than batch/fed-batch system, and yield a several percentage higher titer as well. The productivity ratio of MSC-HCDC over batch/fed-batch system is given as a multiplication of system dilution rate of MSC-HCDC and cycle time of batch/fed-batch system. We suggest MSC-HCDC as a new production platform for various fermentation products including monoclonal antibody.     

Mannitol production by Leuconostoc citreum KACC 91348P isolated from Kimchi

Leuconostoc genus, which comprise heterofermentative lactic acid bacteria, reduces fructose to mannitol by recycling intracellular NADH. To evaluate the mannitol productivities of different Leuconostoc species, 5 stock cultures and 4 newly isolated strains were cultivated in MRS and simplified media containing glucose and fructose (1:2 ratio). Among them, L. citreum KACC 91348P, which was isolated from kimchi, showed superior result in cell growth rate, mannitol production rate, and yield in both media. The optimal condition for mannitol production of this strain was pH 6.5 and 30°C. When L. citreum KACC was cultured in simplified medium in a 2 l batch fermenter under optimal conditions, the maximum volumetric productivity was 14.83 g·l(-1)h(-1) and overall yield was 86.6%. This strain is a novel and efficient mannitol producer originated from foods to be used for fermentation of fructose-containing foods.     

Itaconic acid production by immobilizedAspergillus terreus from xylose and glucose

Summary Aspergillus terreus NRRC 1960 spores were entrapped in calcium alginate gel beads or alternotely the fungal mycelium was immobilized either on Celite R-626 or in agar gel cubes, and the biocatalyst was employed both in repeated batch and in continuous column reactors to produce itaconic acid from D-xylose or D-glucose. The highest itaconic acid yield obtained in a submerged culture batch fermentation was 54.5% based on total initial glucose (55 g/l) with a volumetric productivity of 0.32 g/l h, and 44.8% from xylose (67 g/l) with a productivity of 0.20 g/l h. In a repeated batch fermentation mycelium immobilized in agar gel had a productivity of 0.112 g/l h, and mycelium grown from spores immobilized in calcium alginate gel 0.06 g/l h, both from xylose (60 g/l). With the best immobilized biocatalyst system used employing Celite R-626 as a carrier, volumetric productivities of 1.2 g/l h from glucose and 0.56 g/l h from xylose (both at 60 g/l) were obtained in continuous column operation for more than 2 weeks.     

Succinic acid production from continuous fermentation process using Mannheimia succiniciproducens LPK7

To achieve a higher succinic acid productivity and evaluate the industrial applicability, this study used Mannheimia succiniciproducens LPK7 (knock-out: lahA, pflB, pta-ackA), which was recently designed to enhance the productivity of succinic acid and reduce by-product secretion. Anaerobic continuous fermentation of Mannheimia succiniciproducens LPK7 was carried out at different glucose feed concentrations and dilution rates. After extensive fermentation experiments, a succinic acid yield and productivity of 0.38 mol/mol and 1.77 g/l/h, respectively, were achieved with a glucose feed concentration of 18.0 g/l and 0.2 h-1 dilution rate. A similar amount of succinic acid production was also produced in batch culture experiments. Therefore, these optimal conditions can be industrially applied for the continuous production of succinic acid. To examine the quantitative balance of the metabolism, a flux distribution analysis was also performed using the metabolic network model of glycolysis and the pentose phosphate pathway.