Effect of heating rate on pDNA production by E. coli

The effects of heating rate (HR) on the performance of two-phase (batch followed by fed-batch) high cell-density cultivations (HCDC) of E. coli DH5α for the production of plasmid DNA (pDNA) were investigated. Optimal temperatures for the HCDC, as selected from shake flask experiments at constant temperatures between 30 and 45 °C, were 35 °C for biomass accumulation in the batch phase and 42 °C for inducing pDNA replication during the fed-batch. In HCDC the temperature was increased at HR of 0.025, 0.05, 0.10 and 0.25 °C/min and the performance of the cultivations were compared to a HCDC run at constant temperature (35 °C). Compared to constant 35 °C, heat-induced HCDC accumulated up to 50% less biomass within the same cultivation time and acetate and glucose accumulated to high concentrations. The overall specific productivity (Q_P) and average pDNA yield (Y_p/x) in HCDC at 35 °C were 0.22 ± 0.02 mg/g h and 5.3 ± 0.00 mg/g, respectively. Such parameters were maximum at a HR of 0.05 °C/min, reaching 0.56 ± 0.06 mg/g h and 9.3 ± 0.6 mg/g, respectively. At HR above 0.5 °C/min, Y_p/x remained relatively constant, whereas Q_P tended to decrease. The supercoiled pDNA fraction remained around 80% at all HR. Bioreactors were equipped with a capacitance/conductivity probe. In all cases biomass concentration correlated closely with the capacitance signal and acetate and glucose accumulation was accompanied by an increase in the conductivity signal. Thus, it was possible to calculate acetate and biomass concentrations, as well as μ, from online capacitance and conductivity signals using estimators. Altogether, in this study it was shown that it is possible to maximize pDNA productivity by choosing an appropriate HR and that relevant parameters can be estimated by capacitance/conductivity signals, which are useful for better process control and development.     

Prefermentation to overcome nutrient limitations in food processing wastewater: Comparison of pilot- and bench-scale systems

A bench- and a pilot-scale anaerobic/aerobic system were evaluated for the treatment of high strength tomato-processing wastewater. The pilot-scale anaerobic tank achieved better prefermentation of organic carbon and nitrogen than the bench-scale system, although overall system performance was comparable with more than 99% SBOD removal and 97% SCOD removal. Hydraulic retention time (HRT) and temperature effects were studied in the bench-scale system. Increase of anaerobic HRT from 0.25 day to 0.5 day favored prefermentation and a better effluent quality was achieved, as demonstrated by reduction in TSS concentrations from 66 mg/L to 24 mg/L, SCOD from 103 mg/L to 78 mg/L and SBOD from 8 mg/L to 6 mg/L, respectively. Specific oxygen uptake rate (SOUR) increased from 0.15–0.23 mg O₂/mg VSS day at 25 °C to 0.67–1.24 mg O₂/mg VSS day at 32 °C. Settling characteristics deteriorated from sludge volume index (SVI) of 24–131 mL/g at 25 °C to 115–173 mL/g at 32 °C. Sludge yield decreased from 0.14 g VSS/g COD at 25 °C to 0.098 g VSS/g COD at 32 °C.     

Temperature-dependent development of Lista haraldusalis (Walker) (Lepidoptera: Pyralidae) on Platycarya strobilacea

The effect of constant temperatures on development and survival of Lista haraldusalis (Walker) (Lepidoptera: Pyralidae), a newly reported insect species used to produce insect tea in Guizhou province (China), was studied in laboratory conditions at seven temperatures (19 °C, 22 °C, 25 °C, 28 °C, 31 °C, 34 °C, and 37 °C) on Platycarya strobilacea. Increasing the temperature from 19 °C to 31 °C led to a significant decrease in the developmental time from egg to adult emergence, and then the total developmental time increased at 34 °C. Egg incubation was the stage where L. haraldusalis experienced the highest mortality at all temperatures. The survival of L. haraldusalis was significantly higher at 25 °C and 28 °C, whereas none of the eggs hatched at 37 °C. Common and Ikemoto linear models were used to describe the relationship between the temperature and the developmental rate for each immature stage of L. haraldusalis. The estimated values of the lower temperature threshold and thermal constant of the total immature stages using Common and Ikemoto linear models were 11.34 °C and 11.20 °C, and 939.85 and 950.41 degree-days, respectively. Seven nonlinear models were used to fit the experimental data to estimate the developmental rate of L. haraldusalis. Based on the biological significance for model evaluation, Ikemoto linear, Logan-6, and SSI were the best models that fitted each immature stage of L. haraldusalis and they were used to estimate the temperature thresholds. These thermal requirements and temperature thresholds are crucial for facilitating the development of factory-based mass rearing of L. haraldusalis.     

Effect of variable dew temperatures on infection of green foxtail by Pyricularia setariae,Drechslera gigantea,and Exserohilum rostratum

A thermogradient apparatus was used to investigate the effect of variable dew temperatures on infection of green foxtail by the indigenous pathogen Pyricularia setariae (Ps) and the exotic pathogens Drechslera gigantea (Dg), and Exserohilum rostratum (Er) from the southern USA that showed bioherbicide potential against several grassy weeds. This device is capable of creating multiple diurnal temperature cycles, mimicking daily temperature fluctuations that occur under field conditions. Seven temperature regimes, i.e., 15/10 °C, 20/5 °C, 20/15 °C, 25/10 °C, 25/20 °C, 30/15 °C, and 30/25 °C (maximum/minimum), were used with temperature cycling from maximum to minimum and then back up to maximum in a 24 h period. Ps and Dg were much more virulent than Er on green foxtail, resulting in higher levels of disease and weed control. Dg was little affected by the dew temperatures in terms of plant infection and was more efficacious than Ps under cooler dew temperatures (15/10 °C and 20/5 °C), causing twice as much disease. This greater amount of disease coincided with higher conidial germination, appressorial formation and infection-hypha frequency by Dg at the lower temperatures. The efficacy of Ps improved as dew temperature increased, accompanied by a higher percentage of germination and more frequent appressorial production. Dg caused severe disease 2 d after inoculation whereas Ps required 4 d to initiate disease symptoms. These observations suggest that Dg is a superior candidate than Ps for green foxtail control on the Canadian prairies.     

Cellulose ethanol production from waste newsprint by simultaneous saccharification and fermentation using Saccharomyces cerevisiae KNU5377

A thermotolerant ethanol-fermenting yeast, Saccharomyces cerevisiae KNU5377, isolated from a sludge of a local industrial complex stream in Korea, was evaluated for its capability for lignocellulosic ethanol production from waste newsprint in high temperature. In this fermentation, most of dry-defibrated waste newspaper was first saccharified at 50 °C for 108 h using a commercial cellulase and, then with the last addition of dry-defibrated newsprints to the pre-saccharified broth, simultaneous saccharification and fermentation (SSF) of 1.0 L of reaction mixture was carried out at 40 °C, slowly being dropped from 50 °C, for further 72 h in a 5 L fermentor by inoculating the overnight culture of KNU5377. The maximum production of 8.4% (v/v) ethanol was obtained when 250 g (w/v)/L of dry-defibrated waste newspaper was used for ethanol production by SSF. These results suggest that S. cerevisiae KNU5377 is very useful for cellulose ethanol production by the SSF system.     

β-Galactosidase of Aspergillus oryzae immobilized in an ion exchange resin combining the ionic-binding and crosslinking methods: Kinetics and stability during the hydrolysis of lactose

In this work, the hydrolysis kinetics of lactose by Aspergillus oryzae β-galactosidase was studied using the ionic exchange resin Duolite A568 as a carrier. The enzyme was immobilized using a β-galactosidase concentration of 16 g/L in pH 4.5 acetate buffer and an immobilization time of 12 h at 25 ± 0.5 °C. Next, the immobilized β-galactosidase was crosslinked using glutaraldehyde concentration of 3.5 g/L for 1.5 h. The influence of lactose concentration was studied for a range of 5–140 g/L, and the Michaelis–Menten model was fitted well to the experimental results with V_m and K_m values of 0.71 U and 35.30 mM, respectively. The influence of the product galactose as an inhibitor on the hydrolysis reaction was studied. The model that was best fitted to the experimental results was the competitive inhibition by galactose with V_m, K_m and K_i values of 0.77 U, 35.30 mM and 27.44 mM, respectively. The influence of temperature on the enzymatic activity of the immobilized enzyme was studied in the range of 10–80 °C, in which the temperature of the maximum activity was 60 °C, with an activation energy of 5.32 kcal/mol of lactose, using an initial concentration of lactose of 50 g/L in a pH 4.5 sodium acetate buffer solution. The thermal stability of the immobilized biocatalyst was determined to be in the range 55–65 °C. The first-order model described well the kinetics of thermal deactivation for all the temperatures studied. The activation energy of thermal deactivation from immobilized biocatalyst was 66.48 kcal/mol with a half-life of 8.9 h at 55 °C.     

Overexpression and characterization of a glucose-tolerant β-glucosidase from Thermotoga thermarum DSM 5069T with high catalytic efficiency of ginsenoside Rb1 to Rd

The β-glucosidase gene Tt-bgl from Thermotoga thermarum DSM 5069T was cloned and overexpressed in Escherichia coli. A simple strategy, induction at 37 °C with no IPTG, was explored to reduce the inclusion bodies, by which the activity of Tt-BGL was 13 U/mL in LB medium. Recombinant Tt-BGL was purified by heat treatment followed by Ni–NTA affinity. The optimal activity was at pH 4.8 and 90 °C. The activity of Tt-BGL was significantly enhanced by methanol and Al³⁺. The enzyme was stable over pH range of 4.4–8.0, and had a 2-h half life at 90 °C. The V_max for p-nitrophenyl-β-d-glucopyranoside and ginsenoside Rb1 was 142 U/mg and 107 U/mg, while the K_m was 0.59 mM and 0.15 mM, respectively. The activity of the enzyme was not inhibited by ginsenoside Rb1 (36 g/L). It was activated by glucose at concentrations lower that 400 mM. With glucose further increasing, the activity of Tt-BGL was gradually inhibited, but remained 50% of the original value in even as high as 1500 mM glucose. Under the optimal conditions, Tt-BGL transformed ginsenoside Rb1 (36 g/L) to Rd by 95% in 1 h.     

Application of seaweeds for the removal of lead from aqueous solution

Ten different seaweed species were compared on the basis of lead uptake at different pH conditions. The brown seaweed, Turbinaria conoides, exhibited maximum lead uptake (at pH 4.5) and hence was selected for further studies. Sorption isotherms, obtained at different pH (4–5) and temperature (25–35 °C) conditions were fitted using Langmuir and Sips models. According to the Langmuir model, the maximum lead uptake of 439.4 mg/g was obtained at optimum pH (4.5) and temperature (30 °C). The Sips model better described the sorption isotherms with high correlation coefficients at all conditions examined. Various thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated indicating that the present system was a spontaneous and endothermic process. Through potentiometric titrations, number of binding sites (carboxyl groups) and pK₁ were determined as 4.1 mmol/g and 4.4, respectively. The influence of co-ions (Na⁺, K⁺, Mg²⁺ and Ca²⁺) on lead uptake was well pronounced in the case of divalent ions compared to monovalent ions. The solution of 0.1 M HCl successfully eluted all lead ions from lead-loaded T. conoides biomass. The regeneration experiments revealed that the alga could be successfully reused for five cycles without any loss in lead biosorption capacity. A glass column (2 cm i.d. and 35 cm height) was used to study the continuous lead biosorption performance of T. conoides. At 25 cm (bed height), 5 ml/min (flow rate) and 100 mg/l (initial lead concentration), T. conoides exhibited lead uptake of 220.1 mg/g. The column was successfully eluted using 0.1 M HCl, with elution efficiency of 99.7%.     

Combined effects of temperature and cadmium on developmental parameters and biomarker responses in zebrafish (Danio rerio) embryos

To determine the interactions between temperature and cadmium on zebrafish (Danio rerio) development, fertilized eggs were exposed to combinations of three temperature levels (21 °C, 26 °C, and 33 °C) and six cadmium concentrations (0, 0.25, 0.5, 2.0, 5.0, and 10.0 mg/L). Endpoints used included LC₅₀ value (48 h), developmental rate, mortality, heart rate, hatching success, liver histopathology, embryo abnormalities, and heat shock protein (hsp) induction. Results showed a significant acceleration in the developmental rate with increasing temperature and irrespective of the presence of cadmium. Data on LC₅₀ and ELS-test revealed that simultaneous exposure to both cadmium ions and cold stress (21 °C) was highly detrimental to growing embryos, causing a pronounced mortality and a significant reduction in average heart rate and embryo hatchability. In contrast, no similar reactions to cadmium were observed in pre-hatched embryos exposed to both control (26 °C) and high temperature (33 °C), and this can be explained by the significantly higher expression of hsp (hsp70) in embryos at these temperatures. Upon hatching, however, the larvae showed increased sensitivity to cadmium. The severity of malformations in the post-hatched larvae was in the order: hot cadmium stress>cold cadmium stress>cadmium stress alone>no stress at all. Liver histopathology as well as depletion in glycogen reserves exhibited greater severity with increasing cadmium concentration, irrespective of temperature. The present study confirms that temperature effectively confounds cadmium toxicity and needs to be considered for the accurate prediction and assessment of cadmium-induced toxicity in fish.     

A novel medium for the production of cephamycin C by Nocardia lactamdurans using solid-state fermentation

In this study, Nocardia lactamdurans NRRL 3802 was explored for the first time for production of cephamycin C by using solid-state fermentation. The effects of various substrates, moisture content, inoculum size, initial pH of culture medium, additional nitrogen source and amino acids were investigated for the maximum production of cephamycin C by N. lactamdurans NRRL 3802 in solid-state fermentation. Subsequently, selected fermentation parameters were further optimized by response surface methodology (RSM). The soybean flour as a substrate with moisture content of 65%, initial pH of culture medium of 6.5 and inoculum size of 10⁹ CFU/ml (2 × 10⁸ CFU/gds) at 28 ± 2 °C after 4 days gave maximum production of 15.75 ± 0.27 mg/gds of cephamycin C as compared to 8.37 ± 0.23 mg/gds before optimization. Effect of 1,3-diaminopropane on cephamycin C production was further studied, which further increased the yield to 27.64 ± 0.33 mg/gds.     

Optimization of a biotransformation process to produce 4-(2,3,5,6-tetramethylpyrazine-1)-4′-demethylepipodophyllotoxin

The developed tandem biotransformation process for the directional biosynthesis of a designed compound 4-(2,3,5,6-tetramethylpyrazine-1)-4′-demethylepipodophyllotoxin (4-TMP-DMEP) by Alternaria alternata S-f6 was systematically optimized. 28 °C of culture temperature and 120 rpm of rotary shaker speed were suitable for the accumulation of 4-TMP-DMEP. The production (i.e., 11.1 ± 1.4 mg/L) of 4-TMP-DMEP was remarkably improved by using an initial yeast extract concentration of 2.5 g/L. 2.0 g/L of Span 80 was beneficial for the 4-TMP-DMEP production (i.e., 25.0 ± 1.5 mg/L). Furthermore, the 4-TMP-DMEP production was remarkably improved by one pulse feeding of 50 mg/L of DMEP on day 6 and two pulse feedings of 40 mg/L of TMP on days 8 and 14 when its residual level was below 50 mg/L and 10 mg/L, respectively. The 4-TMP-DMEP production of 45.1 ± 1.6 mg/L was obtained in the fed-batch biotransformation process, which was enhanced by 726% and 256%, comparing to that (i.e., 5.4 ± 0.4 mg/L and 0.9 mg/L/day) obtained in the batch biotransformation before optimization.     

The production of a cold-induced extracellular biopolymer by Pseudomonas fluorescens BM07 under various growth conditions and its role in heavy metals absorption

The psychrotrophic bacterium Pseudomonas fluorescens BM07 was induced to excrete an extracellular biopolymer when cells were grown aerobically at 10 °C and its secretion was inhibited at 30 °C. The biopolymer was easily torn apart from the cells by using a shear force under centrifugation (8700 × g, 30 min) and collected as a well-separated mucoid layer in centrifuge tube. The production of the biopolymer was affected by factors such as the types of carbon and nitrogen sources, temperature, and pH. The best production of 2.5 g/l was obtained when the cells were grown on M1 medium containing 70 mM sucrose and 0.2% (w/v) Casamino Acids. In Kings B enriched medium a maximum biopolymer production of up to 3.4 g/l and growth rate of 2.1 g/l, were achieved using 1:1 ratio of C/N. Addition of NaCl and ethanol to the medium led to a decrease in biopolymer production and growth rate of BM07 strain. FT-IR spectroscopy demonstrated the presence of carboxyl, amine, hydroxyl and methoxyl functional groups in the biopolymer. BM07 biopolymer showed high ion binding capacity with particular preference to uptake cadmium and mercury (∼45 and 70%, respectively). The percentage removal of cobalt, zinc, nickel and copper cations were between 20 and 30%. Overall ion uptake by BM07 biopolymer showed a definite preference for larger over smaller cations (Hg > Cd > Ni > Zn > Cu > Co).     

Mixed culture of Saccharomyces cerevisiae and Acetobacter pasteurianus for acetic acid production

Mixed culture of Saccharomyces cerevisiae and Acetobacter pasteurianus was carried out for high yield of acetic acid. Acetic acid production process was divided into three stages. The first stage was the growth of S. cerevisiae and ethanol production, fermentation temperature and aeration rate were controlled at 32 °C and 0.2 vvm, respectively. The second stage was the co-culture of S. cerevisiae and A. pasteurianus, fermentation temperature and aeration rate were maintained at 34 °C and 0.4 vvm, respectively. The third stage was the growth of A. pasteurianus and production of acetic acid, fermentation temperature and aeration rate were controlled at 32 °C and 0.2 vvm, respectively. Inoculation volume of A. pasteurianus and S. cerevisiae was 16% and 0.06%, respectively. The average acetic acid concentration was 52.51 g/L under these optimum conditions. To enhance acetic acid production, a glucose feeding strategy was subsequently employed. When initial glucose concentration was 90 g/L and 120 g/L glucose was fed twice during fermentation, acetic acid concentration reached 66.0 g/L.     

Biodegradation of toluene at high initial concentration in an organic–aqueous phase bioprocess with nitrate respiration

An aerobic organic–aqueous system with forced aeration was shown to be inefficient in preventing significant volatile aromatic compounds loss in gassed systems since air sparging in n-hexadecane under abiotic conditions could reduce the toluene concentration from 2.1 g/L to about 0.5 g/L in 3 days with a gassing rate of 1VVM at 20 °C. However, the presence of such an organic phase was found to significantly reduce substrate loss in aerobic conditions in comparison to pure aqueous systems. It was thus decided to develop a new bioprocess based on an anaerobic microbial system operated in an organic–aqueous phase with nitrate respiration. The denitrifying bacterium used, Thauera aromatica K172, was produced by cultivation on sodium benzoate as carbon source under anaerobic conditions. This cultivated biomass (1.5 g/L) was shown to retain its ability to efficiently metabolize toluene in a biphasic medium without any significant loss of organic compound in the gas phase. Toluene biodegradation was thus performed in a biphasic system using a fed-batch technique involving sequential adding of both toluene and nitrate. The reaction rate with an initial concentration of toluene close to 14.5 g/L in hexadecane was found to be close to 0.5 g/L day and the molar stoichiometry of solute metabolization to nitrate reduction was close to 1:6. This work demonstrated that the denitrifying bacteria could efficiently degrade toluene in hexadecane–aqueous phase systems in which toxic compound release in the environment was prevented.     

Biology and thermal requirements of Chrysoperla genanigra (Neuroptera: Chrysopidae) reared on Sitotroga cerealella (Lepidoptera: Gelechiidae) eggs

Chrysoperla genanigra Freitas is a common green lacewing associated with melon pests in the Northeastern Brazil. All life stages of this recently described species were studied under a range of constant temperature conditions (17, 21, 25, 29, 33, 35 and 37 °C), a photoperiod of 12 h:12 h (L:D) and 70 ± 10% relative humidity. Adults of C. genanigra were fed on a diet consisting of a 1:1 (v/v) mixture of brewer’s yeast and honey, while larvae were provided with eggs of Sitotroga cerealella (Olivier) ad libitum. The duration of preimaginal development of the species was inversely proportional to temperature and ranged from approximately 63 days at 17 °C to 15 days at 35 °C. The percentage of adult emergence varied from 6.7% at 17 °C to 76.7% at 25 °C, although no larvae were able to complete development at 37 °C. The lower thermal threshold for total preimaginal development was approximately 10.8 °C and the thermal requirement was 336.7 degree-days. Egg production, along with the longevity of both males and females, were significantly affected by temperature. It is concluded that the best temperature for rearing C. genanigra is 25 °C, with the lowest preimaginal mortality and the highest egg production (992.7 eggs/female).     

Effect of rearing temperature on growth and thermal tolerance of Schizothorax (Racoma) kozlovi larvae and juveniles

Effect of rearing temperature on growth and thermal tolerance of Schizothorax (Racoma) kozlovi Nikolsky larvae and juveniles was investigated. The fish (start at 12 d post hatch) were reared for nearly 6 months at five constant temperatures of 10, 14, 18, 22 and 26 °C. Then juvenile fish being acclimated at three temperatures of 14, 18 and 22 °C were chosen to determine their critical thermal maximum (CTMax) and lethal thermal maximum (LTMax) by using the dynamic method. Growth rate of S. kozlovi larvae and juveniles was significantly influenced by temperature and fish size, exhibiting an increase with increased rearing temperature, but a decline with increased fish size. A significant ontogenetic variation in the optimal temperatures for maximum growth were estimated to be 24.7 °C and 20.6 °C for larvae and juveniles of S. kozlovi, respectively. The results also demonstrated that acclimation temperature had marked effects on their CTMax and LTMax, which ranged from 32.86 °C to 34.54 °C and from 33.79 °C to 34.80 °C, respectively. It is suggested that rearing temperature must never rise above 32 °C for its successful aquaculture. Significant temperature effects on the growth rate and thermal tolerance both exhibit a plasticity pattern. Determination of critical heat tolerance and optima temperature for maximum growth of S. kozlovi is of ecological significance in the conservation and aquaculture of this species.     

Thermal tolerance and preference of exploited turbinid snails near their range limit in a global warming hotspot

Predicted global climate change has prompted numerous studies of thermal tolerances of marine species. The upper thermal tolerance is unknown for most marine species, but will determine their vulnerability to ocean warming. Gastropods in the family Turbinidae are widely harvested for human consumption. To investigate the responses of turbinid snails to future conditions we determined critical thermal maxima (CTMax) and preferred temperatures of Turbo militaris and Lunella undulata from the tropical-temperate overlap region of northern New South Wales, on the Australian east coast. CTMax were determined at two warming rates: 1 °C/30 min and 1 °C/12 h. The number of snails that lost attachment to the tank wall was recorded at each temperature increment. At the faster rate, T. militaris had a significantly higher CTMax (34.0 °C) than L. undulata (32.2 °C). At the slower rate the mean of both species was lower and there was no significant difference between them (29.4 °C for T. militaris and 29.6 °C for L. undulata). This is consistent with differences in thermal inertia possibly allowing animals to tolerate short periods at higher temperatures than is possible during longer exposure times, but other mechanisms are not discounted. The thermoregulatory behaviour of the turban snails was determined in a horizontal thermal gradient. Both species actively sought out particular temperatures along the gradient, suggesting that behavioural responses may be important in ameliorating short-term temperature changes. The preferred temperatures of both species were higher at night (24.0 °C and 26.0 °C) than during the day (22.0 °C and 23.9 °C). As the snails approached their preferred temperature, net hourly displacement decreased. Preferred temperatures were within the average seasonal seawater temperature range in this region. However, with future predicted water temperature trends, the species could experience increased periods of thermal stress, possibly exceeding CTMax and potentially leading to range contractions.     

Lipolytic enzyme production by Thermus thermophilus HB27 in a stirred tank bioreactor

In this study, lipolytic enzyme production by Thermus thermophilus HB27 at bioreactor scale has been investigated. Cultivation was performed in a 5-L stirred tank bioreactor in discontinuous mode, at an agitation speed of 200 rpm. Different variables affecting intra- and extra-cellular lipolytic enzyme production such as culture temperature and aeration rate have been analysed. The bacterium was able to grow within the temperature range tested (from 60 to 70 °C) with an optimum value of 70 °C for intra- and extra-cellular lipolytic enzyme production.On the other hand, various aeration levels (from 0 to 2.5 L/min) were employed. A continuous supply of air was necessary, but no significant improvement in biomass or enzyme production was detected when air flow rates were increased above 1 L/min. Total lipolytic enzyme production reached a maximum of 167 U/L after 3 days, and a relatively high concentration of extra-cellular activity was detected (40% of the total amount). Enzyme yield was around 158 U/g cells. Moreover, it is noteworthy that the lipolytic activity obtained operating at optimal conditions (70 °C and air flow of 1 L/min) was about five-fold higher than that attained in shake flask cultures     

Production,characterization and antioxidant activities in vitro of exopolysaccharides from endophytic bacterium Paenibacillus polymyxa EJS-3

The production, characterization and antioxidant activities in vitro of exopolysaccharides (EPS) from endophytic bacterium Paenibacillus polymyxa EJS-3 were investigated. For EPS production, the preferable culture conditions were 24 °C and pH 8 for 60 h with sucrose and yeast extract as the carbon and nitrogen sources, respectively. Notably, sucrose concentration was the prominent factor, and the maximum yield of EPS (22.82 g/L) was obtained at a sucrose concentration of 160 g/L. The crude EPS was purified by chromatography of DEAE-52 and Sephadex G-100, affording EPS-1 and EPS-2 with molecular weights of 1.22 × 10⁶ and 8.69 × 10⁵ Da, respectively. They were composed of mannose, fructose and glucose in a molar ratio of 2.59:29.83:1 and 4.23:36.59:1, respectively. In addition, both crude and purified EPS showed strong scavenging activities on superoxide and hydroxyl radicals, and their antioxidant activities decreased in the order of crude EPS > EPS-2 > EPS-1.     

Treatment of dye-rich wastewater by an immobilized thermophilic cyanobacterial strain: Phormidium sp.

The removal of Remazol Blue and Reactive Black B by the immobilized thermophilic cyanobacterial strain Phormidium sp. was investigated under thermophilic conditions in a batch system, in order to determine the optimal conditions required for the highest dye removal. In the experiments, performed at pH 8.5, with different initial dye concentrations between 9.1 mg l⁻¹ and 82.1 mg l⁻¹ and at 45 °C, calcium alginate immobilized Phormidium sp. showed high dye decolorization, with maximum uptake yields ranging from 50% to 88% at all dye concentrations tested. When the effects of high dye concentrations on dye removal were investigated, the highest uptake yield in the beads was 50.3% for 82.1 mg l⁻¹ Remazol Blue and 60.0% for 79.5 mg l⁻¹ Reactive Black B. The highest color removal was detected at 45 °C and 50 °C incubation temperatures for all dye concentrations. As the temperature decreased, the removal yield of immobilized Phormidium sp. also decreased. At about 75 mg l⁻¹ initial dye concentrations, the highest specific dye uptake measured was 41.29–41.17 mg g⁻¹ for Remazol Blue and 47.69–43.82 mg g⁻¹ for Reactive Black B at 45 °C and 50 °C incubation temperatures, respectively, after 8 days incubation.