Reproducible fabrication of miniaturized glucose sensors: preparation of sensing membranes for continuous monitoring.

The immobilization process of glucose oxidase(GOx) in the poly(1,3-diaminobenzene) (poly(1,3-DAB)) network was closely investigated in situ using an electrochemical quartz crystal microbalance(EQCM). GOx captured in approximately 50 nm thick poly-1,3-DAB layer causes a 514 Hz frequency increase, corresponding to 541 ng, and distributes mostly in the outer part of the polymer film. The presence of poly-L-lysine and glutaraldehyde during electropolymerization of poly(1,3-DAB) improves sensitivity by raising the amount of GOx immobilized. Adding a protective membrane on to the enzyme layer from poly(tetrafluoroethylene) (PTFE) dispersed in aqueous media lets the entire fabrication procedure finish perfectly without nonaqueous solvent. The finalized needle-type glucose sensors show competent functions in sensitivity, stability, biocompatibility, lifetime, interference and reproducibility.     

Towards the real-time monitoring of glucose in tear fluid: holographic glucose sensors with reduced interference from lactate and pH

Glucose-selective holographic sensors were fabricated from unique tetrahedral 2-acrylamidophenylboronic acid (2-APB) incorporated with co-monomers poly(ethylene glycol) acrylate (PEG), (3-acrylamidopropyl)trimethylammonium chloride (ATMA) and [2-(acryloyloxy)ethyl]-trimethylammonium chloride (AETA) into thin hydrogel films which were transformed into volume holograms using a diffusion method coupled with holographic recording using a frequency-doubled Nd:YAG laser (532 nm). The results showed that the 2-APB-based holographic sensors contracted upon addition of glucose due to the formation of a 2:1 complex between the tetrahedral 2-APB and glucose. More significantly, the 2-APB-based holographic sensors had greatly reduced lactate dependence and a hugely reduced pH effect over the physiological range of pH. These features are vital for development of contact lens-based glucose sensor, where the pH variability is greater (pH 5.8-7.8) and the lactate concentration is substantially higher than in blood. Furthermore, the 2-APB-based holographic sensors also displayed fast response to glucose. The successful union of holograms and the tetrahedral 2-APB receptor for glucose detection in artificial tear fluid is also demonstrated. This new type of holographic sensors responding to glucose with features of minor pH effect and negligible interference from lactate is applicable to the detection of glucose concentrations in tear fluid for the management of diabetes.     

Magnetic acoustic resonance immunoassay (MARIA): a multifrequency acoustic approach for the non-labelled detection of biomolecular interactions

A unique sensing platform, comprising an electromagnetic field detector and an acoustic resonator, has been used as a wireless system for remote sensing of biorecognition events. The MARS (Magnetic Acoustic Resonator Sensor) technique has proven useful for detecting the formation of protein multilayers derived from specific binding phenomena. The technique enables multifrequency analysis, without the need of electrodes attached to the sensing element, and also facilitates the in situ surface modification of the substrate for antibody attachment. The MARS sensor was utilized as the platform on which a standard immunoassay was carried out. Two different conditions for the attachment of the first antibody to the quartz surface were tested: (i) Adsorption of the antibody onto the surface of a bare quartz disc; (ii) covalent immobilization of the antibody to a chemically modified quartz surface. Both methods can be successfully utilized for the 'label-less' detection of the biorecognition event between goat IgG and anti-goat IgG by analysis of the multifrequency spectrum. Covalent attachment of the primary antibody results in a more efficient immobilization, with higher surface density, and a consistently enhanced response for the binding of the secondary antibody. This approach will be of interest to life scientists and biochemists that require high performance assay methodologies that do not use chemical labels.     

Amperometric glucose sensor based on coimmobilization of glucose oxidase and Poly(p-phenylenediamine) at a platinum microdisk electrode

A miniaturized glucose biosensor in which glucose oxidase (GOD) and poly(p-phenylenediamine) (poly-PPD) were coimmobilized at the surface of a platinum microdisk electrode was developed and used successfully for amperometric determination of glucose. The performance of sensors prepared at different monomer concentrations and polymerization potentials with different media was investigated in detail. It was found that similarly to poly(o-phenylenediamine) (poly-OPD), (poly-PPD) noticeably eliminated the electrochemical interference of ascorbic acid, uric acid, and l-cysteine. The amperometric response of glucose with the biosensor under optimal conditions exhibited a linear relationship in the range of 5.0 x 10(-5) to 3.0 x 10(-3) M with correlation coefficient 0.9995. According to the Michaelis-Menten equation, the apparent Michaelis constant for glucose and the maximum steady-state current density of the poly-PPD/GOD-modified microelectrode were 3.94 mM and 607.5 microA cm(-2), respectively. The current density of the sensor responding to glucose in the linear range can reach 160 microA cm(-2) mM(-1), which is far greater than that obtained using poly-OPD and poly(phenol) film. In addition, the stability of the sensor was examined over a 2-month period.     

Significantly Enhanced Electrostatic Energy Storage Performance of Flexible Polymer Composites by Introducing Highly Insulating‐Ferroelectric Microhybrids as Fillers

A hybrid nanoparticle, consisting of BaTiO₃ nanoparticles tightly embedded in bronnitride (BN) nanosheets, has been fabricated based on a daring supposition that BN may act as a host to incorporate ferroelectric nanoparticles to improve insulation and polarization under a high electric field. Using the hybrids as fillers in poly(vinylidene fluoride) (PVDF) composites, a high electric breakdown strength (E_b ≈580 kV/mm), which is 1.76 times of the PVDF film, is obtained when the filler content is 5 wt%. A large displacement (9.3 µC/cm² under 580 kV/mm) is observed so as to obtain a high discharged energy density (U_d ≈17.6 J/cm³) of the BT@BN/PVDF composites, which is 2.8 times of the PVDF film. The enhancement ratio of E_b achieved in this study demonstrates the highest among the reported results. This hybrid structure of fillers provides an effective way to adjust and improve the energy storage properties of the polymer‐based dielectrics.     

Structural behavior of nanometric carbohydrate films transduced by a resonant technique

New optical nanoresonance effects enabled us to study the effect of ions on nanometric carbohydrate thin layers on chips. Immobilization was done via spin coating of the derivatized carbohydrate polymer at a metallized chip surface forming ultrathin films (about 50-300 nm thick) followed by photochemical cross-linking. Deposition of metal-nanoclusters, synthesized by chemical means and sputter coating on top of the polymer, induced an optical resonance effect, which transduced changes of polymer structure quantitatively into an optical signal that can be observed directly as resonance shift of a narrow optical peak. The response of the sensor chip even visible to the eye was quantified spectroscopically in the visible and ir range of the spectrum. The lifetime of thin film was good, and thus application as a sensor was limited only by the mechanical stability of the reactive matrix, but not by photobleaching or molecular leakage. Due to the inherent hydrophilic nature of the alginate polymer, the response time of this new sensor is governed by simple aqueous diffusion of the ionic calcium for up to 300 nm completed within less than one second. Monitoring of calcium fluctuations in a high background of magnesium and even serum was demonstrated with a dynamic range optimal for physiological measurements and a linear response up to 5 mM. Surface and alignment of polymer chain were influenced by the nanostructure of the supporting metal film-contrary to alginic acid, chitosan was deposited well aligned to the nanocrystals of the support.     

Holographic glucose sensors

A novel holographic sensor system capable of detecting dynamic changes in glucose concentration has been developed. The hologram is recorded within a bio-compatible hydrogel matrix containing phenylboronic acid derivatives. On binding glucose, the colour of the hologram red-shifts to longer wavelengths as the hydrogel expands and this colour change is used to quantify glucose concentration. However, phenylboronic acids are non-selective and bind a wide variety of cis-diols. In blood, glucose is the only sugar found free at high concentration, whilst other sugars are typically found as part of glycoproteins and macromolecular structures. Although glycoproteins have been shown to have no effect on the sensor, phenylboronic acids can bind lactate much more readily than glucose. We have designed two polymer hydrogel systems to increase the selectivity of the sensor for glucose over lactate. The first involved the use of high concentrations of 3-acrylamidophenylboronic acid (3-APB) whilst the second system utilised 2-acrylamido-5-fluorophenylboronic acid (5-F-2-MAPB). Both systems displayed an increased selectivity to glucose over lactate at physiological pH and ionic strength and could be deployed as selective holographic sensors for glucose detection in physiological fluids.     

A contact lens with embedded sensor for monitoring tear glucose level

We report the design, construction, and testing of a contact lens with an integrated amperometric glucose sensor, proposing the possibility of in situ human health monitoring simply by wearing a contact lens. The glucose sensor was constructed by creating microstructures on a polymer substrate, which was subsequently shaped into a contact lens. Titania sol-gel film was applied to immobilize glucose oxidase, and Nafion? was used to decrease several potential interferences (ascorbic acid, lactate, and urea) present in the tear film. The sensor exhibits a fast response (20s), a high sensitivity (240 μA cm(-2) mM(-1)) and a good reproducibility after testing a number of sensors. It shows good linearity for the typical range of glucose concentrations in the tear film (0.1-0.6 mM), and acceptable accuracy in the presence of interfering agents. The sensor can attain a minimum detection of less than 0.01 mM glucose.     

QCM-FIA with PGMA coating for dynamic interaction study of heparin and antithrombin III

In this work, we describe a method of constructing a film of linear poly(glycidyl methacrylate) (PGMA) polymer onto the surface of quartz crystal microbalance (QCM) electrode as a coating material that allows easy coupling of heparin molecules onto the electrode and facilitates the determination of the interaction between heparin and antithrombin III (AT III). The PGMA film was characterized with atomic force microscopy (AFM) and infra-red spectroscopy. The coupling of heparin was accomplished in one step solution reaction. A home-made quartz crystal microbalance-flow injection analysis (QCM-FIA) system with data analysis software developed in our laboratory was used to determine the interaction. The interactions between immobilized heparin and AT III were studied with various concentrations under various conditions. The obtained constants are kass=(1.49+/-0.12)x10(3)mol-1ls-1, kdiss=(3.94+/-0.63)x10(-2)s-1, KA=(3.82+/-0.33)x10(4)mol-1l.     

Mild and modular surface modification of cellulose via hetero Diels-Alder (HDA) cycloaddition

A combination of reversible addition-fragmentation chain transfer (RAFT) polymerization and hetero Diels-Alder (HDA) cycloaddition was used to effect, under mild (T ≈ 20 °C), fast, and modular conditions, the grafting of poly(isobornyl acrylate) (M(n) = 9800 g mol(-1), PDI = 1.19) onto a solid cellulose substrate. The active hydroxyl groups expressed on the cellulose fibers were converted to tosylate leaving groups, which were subsequently substituted by a highly reactive cyclopentadienyl functionality (Cp). By employing the reactive Cp-functionality as a diene, thiocarbonyl thio-capped poly(isobornyl acrylate) synthesized via RAFT polymerization (mediated by benzyl pyridine-2-yldithioformiate (BPDF)) was attached to the surface under ambient conditions by an HDA cycloaddition (reaction time: 15 h). The surface-modified cellulose samples were analyzed in-depth by X-ray photoelectron spectroscopy, scanning electron microscopy, elemental analysis, Fourier transform infrared (FT-IR) spectroscopy as well as Fourier transform infrared microscopy employing a focal plane array detector for imaging purposes. The analytical results provide strong evidence that the reaction of suitable dienophiles with Cp-functional cellulose proceeds under mild reaction conditions (T ≈ 20 °C) in an efficient fashion. In particular, the visualization of individual modified cellulose fibers via high-resolution FT-IR microscopy corroborates the homogeneous distribution of the polymer film on the cellulose fibers.     

Detection of Pseudomonas aeruginosa using a wireless magnetoelastic sensing device

This paper describes the real-time quantification of Pseudomonas aeruginosa (P. aeru) concentrations using a wireless magnetoelastic sensing device. The sensor is fabricated by coating a magnetoelastic ribbon with a polyurethane protecting film. In response to an externally applied time varying magnetic field, the magnetoelastic sensor vibrates at a resonance frequency that can be remotely determined by monitoring the magnetic flux emitted by the sensor. The resonance frequency changes in response to properties changes of a liquid culture medium and bacteria adhesion to the sensor as P. aeru consumes nutrients from the culture medium in growth and reproduction. The effects of properties (conductivity, viscosity, mass) are investigated with quartz crystal microbalance (QCM), microscopy imaging, and conductivity measurement. Using the described technique we are able to directly quantify P. aeru concentrations of 10(3) to 10(8)cells/ml, with a detection limit of 10(3)cells/ml at a noise level of approximately 20 Hz. The lack of any physical connections between the sensor and the monitoring electronics facilitates aseptic operation, and makes the sensor platform ideally suited for monitoring bacteria from within, for example, sealed food containers.     

Electrochemically induced disintegration of layer-by-layer-assembled thin films composed of 2-iminobiotin-labeled poly(ethyleneimine) and avidin

A layer-by-layer assembly composed of avidin and 2-iminobiotin-labeled poly(ethyleneimine) (ib-PEI) was prepared on the surface of a platinum (Pt) film-coated quartz resonator, and an electrochemically induced disintegration of the avidin-ib-PEI assembly was studied using a quartz crystal microbalance. The resonance frequency of a five-bilayer (avidin-ib-PEI)5 film-coated quartz resonator was increased upon application of an electric potential to the Pt layer of the quartz resonator, suggesting that the mass on the quartz resonator was decreased as a result of disintegration of the (avidin-ib-PEI)5 film, due to a pH change in the vicinity of the surface of the Pt-coated quartz resonator. It may be that the (avidin-ib-PEI)5 film assembly was decomposed by acidification of the local pH on the surface of the Pt layer, which in turn was induced through electrolysis of water on Pt, because ib-PEI forms complexes with avidin only in basic media. In pH 9 solution, the (avidin-ib-PEI)5 film was decomposed under the influence of an applied potential of 0.6-1.0 V versus Ag/AgCl. The (avidin-ib-PEI)5 film was decomposed almost completely within a minute in a low concentration buffer (1 mM, pH 9), while the decomposition was slower in 10 and 100 mM buffer solutions at the same pH. The decomposition of the assembly was rapid when the electrode potential was applied in pH 9 solutions, while the response was relatively slow in pH 10 and 11 solutions. All the results are rationalized on the basis of an electrochemically induced acidification of the local environment around the (avidin-ib-PEI)5 film on the Pt layer.     

Measurement of the osmotic properties of thin polymer films and biological tissue samples

A new type of micro-osmometer is described in which water absorption of small tissue samples is measured by a quartz crystal microbalance (QCM). The swelling of the sample deposited on the surface of a quartz crystal is determined by monitoring the change in resonance frequency of the quartz sensor as a function of the vapor pressure in the surrounding environment. The measurement principle is verified by studying the water uptake of poly(vinyl alcohol) films. Reasonable agreement is found between the results obtained by the QCM-based osmometer and previous osmotic pressure measurements made on a similar poly(vinyl alcohol) sample. The feasibility of the new method is demonstrated by measuring the osmotic response of tissue-engineered cartilage samples. It is found that the osmotic pressure of cartilage substantially increases with culture time. The present result is consistent with cartilage models, suggesting that the proteoglycan content governs the compressive resistance of the tissue.     

A New Route to Glucose Sensing Based on Surface Plasmon Resonance Using Polyindole

In the present study, we report the first polyindole-modified metal (Au) as a glucose sensor utilizing surface plasmon resonance (SPR) technique. Polyindole (PIn) was deposited by spin coating to modify the surface of the gold disk. Sensor surface was prepared by immobilizing glucose oxidase on the polyindole-modified gold disk. Different concentrations of glucose were taken to analyze the sensor response. A change in refractive index of the film was observed due to the chemical reactions of glucose with glucose oxidase. The response of the sensor is fast and highly sensitive to low concentrations of glucose and the sensitivity increases in the range of 0.075–0.5 μM. The use of Au/polyindole (PIn/Au) substrates for SPR-based study of bio-molecular sensing has been demonstrated.     

Characterization of QCM sensor surfaces coated with molecularly imprinted nanoparticles

Molecularly imprinted polymers (MIPs) are gaining great interest as tailor-made recognition materials for the development of biomimetic sensors. Various approaches have been adopted to interface MIPs with different transducers, including the use of pre-made imprinted particles and the in situ preparation of thin polymer layers directly on transducer surfaces. In this work we functionalized quartz crystal microbalance (QCM) sensor crystals by coating the sensing surfaces with pre-made molecularly imprinted nanoparticles. The nanoparticles were immobilized on the QCM transducers by physical entrapment in a thin poly(ethylene terephthalate) (PET) layer that was spin-coated on the transducer surface. By controlling the deposition conditions, it was possible to gain a high nanoparticle loading in a stable PET layer, allowing the recognition sites in nanoparticles to be easily accessed by the test analytes. In this work, different sensor surfaces were studied by micro-profilometry and atomic force microscopy and the functionality was evaluated using quartz crystal microbalance with dissipation (QCM-D). The molecular recognition capability of the sensors were also confirmed using radioligand binding analysis by testing their response to the presence of the test compounds, (R)- and (S)-propranolol in aqueous buffer.     

A holographic sensor based on a rationally designed synthetic polymer

A new silver halide-containing holographic recording material has been designed and developed specifically for holographic chemical sensors. The hologram enables very small volume changes to be measured in a polymer layer throughout which the hologram is located. The holographic film is based on a fine-grain silver bromide emulsion suspended in a poly(vinyl alcohol) matrix crosslinked with Cr(III) ions. Cross-linking gives the material sufficient spatial integrity to allow a holographic image to be recorded, while maintaining adequate porosity and elasticity of the polymer matrix for sensing applications. The new material has been characterized with respect to its response to pH and compared with a traditional gelatin holographic film. The response to some ions and small molecules typically found in analytical samples has also been measured. Functional groups introduced covalently into the poly(vinyl alcohol) matrix transform the base matrix into a pH-responsive polymer with predictable swelling properties and which can be further derivatized to incorporate specific ligands. A rationally designed holographic sensor for trypsin has been developed from chemically synthesized artificial polymers. A trypsin substrate, the poly(amino acid) poly(L-lysine), was incorporated into poly(vinyl alcohol) holograms to create a 'designed' holographic material which was degraded in a concentration-dependent manner by trypsin. Extensions of this approach to other hydrolytic enzymes are briefly discussed.     

Glucose sensor using a microfabricated electrode and electropolymerized bilayer films

A new type miniaturized glucose sensor with good selectivity and stable current response has been developed. The structure consists of a recessed rectangular microfabricated platinum electrode, inner layer of two electropolymerized nonconducting films, and outer bilayer of poly(tetrafluoroethylene) (Teflon) and polyurethane (PU) films. Glucose oxidase (GOx) is entrapped during the electropolymerization of a poly(m-phenylenediamine) (PMPD) film in an acetate buffer (AB) solution, on which a highly interference-resistive PMPD film is deposited in a phosphate buffered saline (PBS) solution. The second PMPD film causes no significant decrease in accessibility of glucose to GOx. The inner layer maintains less than 1% permeability to acetaminophen for 12 days. The fairly adhesive outer layer allows stable current response. Due to high permeability, the information about enzyme activity can be obtained without serious error in spite of outer layer intervening between enzymes and solution. The apparent Michaelis-Menten constant and the maximum steady-state current density were 24 mM and 80 microA cm(-2), respectively.     

Localized Surface Plasmon Resonance-Based Fiber Optic U-Shaped Biosensor for the Detection of Blood Glucose

In the present study, we report the first fiber optic glucose sensor utilizing localized surface plasmon resonance of metal nanoparticles. The fiber was bent in the form of a U-shaped probe for point detection and sensitivity enhancement. The probe was prepared by first attaching gold nanoparticles on the optical fiber core and then immobilizing glucose oxidase over it. The sensor operates in the intensity modulation scheme in which the absorbance is measured with respect to the changes in the glucose concentration. The presence of glucose in the vicinity of the sensing region changes the refractive index of the film due to the chemical reactions with glucose oxidase. The absorbance of the metal nanoparticle changes significantly due to local refractive index change. The fiber optic U-shaped probes of different bending radii were fabricated and it has been found that the probe with bending radius around 0.982?mm possesses the maximum sensitivity. The response of the sensor is fast and requires very small volume of sensing sample (??150???l) which makes it more suitable for commercialization and better than present commercial sensors, which require about 1.5?ml of blood for the detection of glucose.     

Glucose sensors based on electrodeposition of molecularly imprinted polymeric micelles: a novel strategy for MIP sensors

A voltammetric glucose sensor was prepared from novel molecularly imprinted polymeric micelles (MIPMs) through direct electrodeposition. The MIPMs, which were photo-crosslinkable and nano-scaled with high specific surface area, were prepared via macromolecule self-assembly of an amphiphilic photo-crosslinkable copolymer, combined with a molecular imprinting technique using glucose as the template molecule. A MIP film was formed in situ on the electrode surface by electrodeposition of the MIPMs, while photo-crosslinking led to a robust film which showed good solvent resistant to dissolution. With these features, the resulting sensor showed good response and selectivity towards glucose. In particular, the linear response of this glucose sensor ranged from 0.2 mM to 8 mM and its comparatively higher detection limit, about 10 mM, indicated numerous effective recognition sites among the polymer matrix due to the large specific surface area of MIPM. In addition, this MIP sensor also showed good stability and reversibility. The contribution of this work lies in not only the invention of a new type of glucose MIP sensor with good performance, but also the creation of a novel strategy to develop advanced MIP sensors for a wide range of templates in viewing of the versatility of the amphiphilic copolymers and the ease of control and applicability of the electrodeposition process.     

Application of parylene-coated quartz crystal microbalance for on-line real-time detection of microbial populations

A novel technique of applying a quartz crystal microbalance (QCM) sensor to the on-line real-time detection of microbial populations is described. The pQCM sensor was fabricated by depositing di-para-xylene (parylene) over the entire surface of a QCM sensor through a chemical vapor deposition (CVD) process. An electrically insulated film of parylene on the QCM sensor enabled the operation of the sensor in the liquid environment, and the resonance frequency of the pQCM sensor set in the medium of a cultivation flask shifted in response to the microbial population. The effects of pH, conductivity, and viscosity of the medium on the frequency shift of the pQCM sensor were investigated. Ignorable responses (less than 1% at 10(3)cells) were obtained during an incubation cycle. The detection limit of the pQCM sensor was identified as 10(2) cells ml(-1) with a frequency shift of around 2 x 10(3)Hz. The cell numbers of Escherichia coli cultivated in both the YEM medium and whole milk were detected. A satisfactory correlation (r(2)=0.95) was obtained between the cell number and the response of the pQCM sensor. Experimental results suggest that the pQCM described here is applicable to the continuous long-term detection of microbial populations during a fermentation process.