Production of acetone,butanol and ethanol by Clostridium beijerinckii BA101 and in situ recovery by gas stripping

We examined the effect of gas-stripping on the in situ removal of acetone, butanol, and ethanol (ABE) from batch reactor fermentation broth. The mutant strain (Clostridium beijerinckii BA101) was not affected adversely by gas stripping. The presence of cells in the fermentation broth affected the selectivities of ABE. A considerable improvement in the productivity and yield was recorded in this work in comparison with the non-integrated process. In an integrated process of ABE fermentation-recovery using C. beijerinckii BA101, ABE productivities and yield were improved up to 200 and 118%, respectively, as compared to control batch fermentation data. In a batch reactor C. beijerinckii BA101 utilized 45.4 g glucose l^–1 and produced 17.7 g total ABE l^–1, while in the integrated process it utilized 161.7 g glucose l^–1 and produced total ABE of 75.9 g l^–1. In the integrated process, acids were completely converted to solvents when compared to the non-integrated process (batch fermentation) which contained residual acids at the end of fermentation. In situ removal of ABE by gas stripping has been reported to be one of the most important techniques of solvent removal. During these studies we were able to maintain the ABE concentration in the fermentation broth below toxic levels.     

Butanol production from wheat straw hydrolysate using <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis>

In these studies, butanol (acetone butanol ethanol or ABE) was produced from wheat straw hydrolysate (WSH) in batch cultures using Clostridium beijerinckii P260. In control fermentation 48.9 g L⁻¹ glucose (initial sugar 62.0 g L⁻¹) was used to produce 20.1 g L⁻¹ ABE with a productivity and yield of 0.28 g L⁻¹ h⁻¹ and 0.41, respectively. In a similar experiment where WSH (60.2 g L⁻¹ total sugars obtained from hydrolysis of 86 g L⁻¹ wheat straw) was used, the culture produced 25.0 g L⁻¹ ABE with a productivity and yield of 0.60 g L⁻¹ h⁻¹ and 0.42, respectively. These results are superior to the control experiment and productivity was improved by 214%. When WSH was supplemented with 35 g L⁻¹ glucose, a reactor productivity was improved to 0.63 g L⁻¹ h⁻¹ with a yield of 0.42. In this case, ABE concentration in the broth was 28.2 g L⁻¹. When WSH was supplemented with 60 g L⁻¹ glucose, the resultant medium containing 128.3 g L⁻¹ sugars was successfully fermented (due to product removal) to produce 47.6 g L⁻¹ ABE, and the culture utilized all the sugars (glucose, xylose, arabinose, galactose, and mannose). These results demonstrate that C. beijerinckii P260 has excellent capacity to convert biomass derived sugars to solvents and can produce over 28 g L⁻¹ (in one case 41.7 g L⁻¹ from glucose) ABE from WSH. Medium containing 250 g L⁻¹ glucose resulted in no growth and no ABE production. Mixtures containing WSH + 140 g L⁻¹ glucose (total sugar approximately 200 g L⁻¹) showed poor growth and poor ABE production. Mention of trade names or commercial products in this article is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

Acetone butanol ethanol (ABE) production from concentrated substrate: reduction in substrate inhibition by fed-batch technique and product inhibition by gas stripping

Acetone butanol ethanol (ABE) was produced in an integrated fed-batch fermentation-gas stripping product-recovery system using Clostridium beijerinckii BA101, with H₂ and CO₂ as the carrier gases. This technique was applied in order to eliminate the substrate and product inhibition that normally restricts ABE production and sugar utilization to less than 20 g l^–1 and 60 g l^–1, respectively. In the integrated fed-batch fermentation and product recovery system, solvent productivities were improved to 400% of the control batch fermentation productivities. In a control batch reactor, the culture used 45.4 g glucose l^–1 and produced 17.6 g total solvents l^–1 (yield 0.39 g g^–1, productivity 0.29 g l^–1 h^–1). Using the integrated fermentation-gas stripping product-recovery system with CO₂ and H₂ as carrier gases, we carried out fed-batch fermentation experiments and measured various characteristics of the fermentation, including ABE production, selectivity, yield and productivity. The fed-batch reactor was operated for 201 h. At the end of the fermentation, an unusually high concentration of total acids (8.5 g l^–1) was observed. A total of 500 g glucose was used to produce 232.8 g solvents (77.7 g acetone, 151.7 g butanol, 3.4 g ethanol) in 1 l culture broth. The average solvent yield and productivity were 0.47 g g^–1 and 1.16 g l^–1 h^–1, respectively.     

<Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> mutant with high inhibitor tolerance obtained by low-energy ion implantation

Clostridium beijerinckii mutant strain IB4, which has a high level of inhibitor tolerance, was screened by low-energy ion implantation and used for butanol fermentation from a non-detoxified hemicellulosic hydrolysate of corn fiber treated with dilute sulfuric acid (SAHHC). Evaluation of toxicity showed C. beijerinckii IB4 had a higher level of tolerance than parent strain C. beijerinckii NCIMB 8052 for five out of six phenolic compounds tested (the exception was vanillin). Using glucose as carbon source, C. beijerinckii IB4 produced 9.1 g l⁻¹ of butanol with an acetone/butanol/ethanol (ABE) yield of 0.41 g g⁻¹. When non-detoxified SAHHC was used as carbon source, C. beijerinckii NCIMB 8052 grew well but ABE production was inhibited. By contrast, C. beijerinckii IB4 produced 9.5 g l⁻¹ of ABE with a yield of 0.34 g g⁻¹, including 2.2 g l⁻¹ acetone, 6.8 g l⁻¹ butanol, and 0.5 g l⁻¹ ethanol. The remarkable fermentation and inhibitor tolerance of C. beijerinckii IB4 appears promising for ABE production from lignocellulosic materials.     

Production of butanol from starch-based waste packing peanuts and agricultural waste

We examined the fermentation of starch-based packing peanuts and agricultural wastes as a source of fermentable carbohydrates using Clostridium beijerinckii BA101. Using semidefined P2 medium containing packing peanuts and agricultural wastes, instead of glucose as a carbohydrate source, we measured characteristics of the fermentation including solvent production, productivity, and yield. With starch as substrate (control), the culture produced 24.7 g l⁻¹ acetone–butanol–ethanol (ABE), while with packing peanuts it produced 21.7 g l⁻¹ total ABE with a productivity of 0.20 g l⁻¹ h⁻¹ and a solvent (ABE) yield of 0.37. Cell growth in starch, packing peanuts, and agricultural wastes medium was different, possibly due to the different nature of these substrates. Using model agricultural waste, 20.3g l⁻¹ ABE was produced; when using actual waste, 14.8 g l⁻¹ ABE was produced. The use of inexpensive substrates will increase the economic viability of the conversion of biomass to butanol, and can provide new markets for these waste streams. Journal of Industrial Microbiology & Biotechnology (2002) 29, 117–123 doi: 10.1038/sj.jim.7000285 Received 14 November 2001/ Accepted in revised form 07 June 2002     

High-titer n-butanol production by clostridium acetobutylicum JB200 in fed-batch fermentation with intermittent gas stripping

Acetone–butanol–ethanol (ABE) fermentation with a hyper‐butanol producing Clostridium acetobutylicum JB200 was studied for its potential to produce a high titer of butanol that can be readily recovered with gas stripping. In batch fermentation without gas stripping, a final butanol concentration of 19.1 g/L was produced from 86.4 g/L glucose consumed in 78 h, and butanol productivity and yield were 0.24 g/L h and 0.21 g/g, respectively. In contrast, when gas stripping was applied intermittently in fed‐batch fermentation, 172 g/L ABE (113.3 g/L butanol, 49.2 g/L acetone, 9.7 g/L ethanol) were produced from 474.9 g/L glucose in six feeding cycles over 326 h. The overall productivity and yield were 0.53 g/L h and 0.36 g/g for ABE and 0.35 g/L h and 0.24 g/g for butanol, respectively. The higher productivity was attributed to the reduced butanol concentration in the fermentation broth by gas stripping that alleviated butanol inhibition, whereas the increased butanol yield could be attributed to the reduced acids accumulation as most acids produced in acidogenesis were reassimilated by cells for ABE production. The intermittent gas stripping produced a highly concentrated condensate containing 195.9 g/L ABE or 150.5 g/L butanol that far exceeded butanol solubility in water. After liquid–liquid demixing or phase separation, a final product containing ～610 g/L butanol, ～40 g/L acetone, ～10 g/L ethanol, and no acids was obtained. Compared to conventional ABE fermentation, the fed‐batch fermentation with intermittent gas stripping has the potential to reduce at least 90% of energy consumption and water usage in n‐butanol production from glucose. Biotechnol. Bioeng. 2012; 109: 2746–2756. © 2012 Wiley Periodicals, Inc.     

Energy-efficient recovery of butanol from model solutions and fermentation broth by adsorption

This article discusses the separation of butanol from aqueous solutions and/or fermentation broth by adsorption. Butanol fermentation is also known as acetone butanol ethanol (ABE) or solvent fermentation. Adsorbents such as silicalite, resins (XAD-2, XAD-4, XAD-7, XAD-8, XAD-16), bone charcoal, activated charcoal, bonopore, and polyvinylpyridine have been studied. Use of silicalite appears to be the more attractive as it can be used to concentrate butanol from dilute solutions (5 to 790–810 g L⁻¹) and results in complete desorption of butanol (or ABE). In addition, silicalite can be regenerated by heat treatment. The energy requirement for butanol recovery by adsorption–desorption processes has been calculated to be 1,948 kcal kg⁻¹ butanol as compared to 5,789 kcal kg⁻¹ butanol by steam stripping distillation. Other techniques such as gas stripping and pervaporation require 5,220 and 3,295 kcal kg⁻¹ butanol, respectively. Mention of trade names of commercial products in this article/publication is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

ABE production from corn: a recent economic evaluation

This article details an economic assessment of butanol production from corn using the newly developed hyper-butanol-producing strain of Clostridium beijerinckii BA101. Butanol is produced in batch reactors and recovered by distillation. For a plant with 153,000 metric tons of acetone, butanol, and ethanol (ABE) production capacity, the production equipment cost and total working capital cost is US$33.47×10⁶ and US$110.46×10⁶, respectively. Based on a corn price (C _p) of US$79.23 ton⁻¹ (US$2.01 bushel⁻¹), an ABE yield of 0.42 (g ABE/g glucose) butanol price is projected to be US$0.34 kg⁻¹. An improved yield of 0.50 will reduce this price to US$0.29 kg⁻¹. Assumptions, such as by-product credit for gases and complete conversion of corn steep liquor (CSL) to fermentation by-products, have been taken into consideration. An increased price of corn to US$197.10 ton⁻¹ would result in a butanol price of US$0.47 kg⁻¹. A grass-rooted plant would result in a butanol price of US$0.73 kg⁻¹ (C _p US$79.23 ton⁻¹). In a worst case scenario, the price of butanol would increase to US$1.07 kg⁻¹ (C _p 197.10 ton⁻¹ for a grass-rooted plant and assuming no credit for gases). This is based on the assumption that corn price would not increase to more than US$197.10 ton⁻¹. Journal of Industrial Microbiology & Biotechnology (2001) 27, 292–297. Received 12 September 2000/ Accepted in revised form 12 January 2001     

Repeated Batch Cultivation of Ralstonia eutropha for Poly (β-hydroxybutyrate) Production

Batch cultivation of Ralstonia eutropha NRRL B14690 attained 21 g biomass l⁻¹ and 9.4 g poly(β-hydroxybutyrate) l⁻¹ (0.45 g PHB g⁻¹ dry wt⁻¹) in 60 h. Repeated batch operation (empty-and-fill protocol) to remove 20% (v/v) of the culture broth and to supplement an equal volume of fresh media resulted in 49 g biomass l⁻¹ and 25 g PHB l⁻¹ (0.51 g PHB g⁻¹ dry wt⁻¹) with an overall productivity of 0.42 g PHB l⁻¹ h⁻¹ in 67 h. In the two cycles of repeated batch fermentation there was a 3-fold increase in productivity as compared to batch.     

Butanol production by Clostridium beijerinckii ATCC 55025 from wheat bran

Wheat bran, a by-product of the wheat milling industry, consists mainly of hemicellulose, starch and protein. In this study, the hydrolysate of wheat bran pretreated with dilute sulfuric acid was used as a substrate to produce ABE (acetone, butanol and ethanol) using Clostridium beijerinckii ATCC 55025. The wheat bran hydrolysate contained 53.1 g/l total reducing sugars, including 21.3 g/l of glucose, 17.4 g/l of xylose and 10.6 g/l of arabinose. C. beijerinckii ATCC 55025 can utilize hexose and pentose simultaneously in the hydrolysate to produce ABE. After 72 h of fermentation, the total ABE in the system was 11.8 g/l, of which acetone, butanol and ethanol were 2.2, 8.8 and 0.8 g/l, respectively. The fermentation resulted in an ABE yield of 0.32 and productivity of 0.16 g l⁻¹ h⁻¹. This study suggests that wheat bran can be a potential renewable resource for ABE fermentation.     

Soy molasses as fermentation substrate for production of butanol using Clostridium beijerinckii BA101

Spray-dried soy molasses (SDSM) contains the sugars dextrose, sucrose, fructose, pinitol, raffinose, verbascose, melibiose, and stachyose. Of the 746 g kg⁻¹ total sugars in SDSM, 434 g kg⁻¹ is fermentable using Clostridium beijerinckii BA101. SDSM was used to produce acetone, butanol, and ethanol (ABE) by C. beijerinckii BA101 in batch cultures. Using 80 g l⁻¹ SDSM, 10.7 g l⁻¹ ABE was produced in P2 medium. Higher concentrations of SDSM resulted in poor solvent production due to the presence of excessive salt and inhibitory components. C. beijerinckii BA101 in SDSM at 80 g l⁻¹ concentration produced 22.8 g l⁻¹ ABE when supplemented with 25.3 g l⁻¹ glucose. SDSM contains 57.4 g kg⁻¹ mineral ash and 2% tri-calcium phosphate. Tri-calcium phosphate up to 43.1 g l⁻¹ was not inhibitory and at a tri-calcium phosphate concentration of 28.8 g l⁻¹, the culture produced more solvents (30.1 g l⁻¹) than the control experiment (23.8 g l⁻¹). In contrast, sodium chloride was a strong inhibitor of C. beijerinckii BA101 cell growth. At a concentration of 10 g l⁻¹ sodium chloride, a maximum cell concentration of 0.6 g l⁻¹ was achieved compared to 1.7 g l⁻¹ in the control experiment. The effects of two salts on specific growth rate constant (μ) and specific rate of ABE production (ν) for C. beijerinckii BA101 were examined. Journal of Industrial Microbiology & Biotechnology (2001) 26, 290–295. Received 20 September 2000/ Accepted in revised form 16 February 2001     

Batch and repeated batch production of l(+)-lactic acid by Enterococcus faecalis RKY1 using wood hydrolyzate and corn steep liquor

Lactic acid production was investigated for batch and repeated batch cultures of Enterococcus faecalis RKY1, using wood hydrolyzate and corn steep liquor. When wood hydrolyzate (equivalent to 50 g l⁻¹ glucose) supplemented with 15–60 g l⁻¹ corn steep liquor was used as a raw material for fermentation, up to 48.6 g l⁻¹ of lactic acid was produced with, volumetric productivities ranging between 0.8 and 1.4 g l⁻¹ h⁻¹. When a medium containing wood hydrolyzate and 15 g l⁻¹ corn steep liquor was supplemented with 1.5 g l⁻¹ yeast extract, we observed 1.9-fold and 1.6-fold increases in lactic acid productivity and cell growth, respectively. In this case, the nitrogen source cost for producing 1 kg lactic acid can be reduced to 23% of that for fermentation from wood hydrolyzate using 15 g l⁻¹ yeast extract as a single nitrogen source. In addition, lactic acid productivity could be maximized by conducting a cell-recycle repeated batch culture of E. faecalis RKY1. The maximum productivity for this process was determined to be 4.0 g l⁻¹ h⁻¹.     

Microbial production of a biofuel (acetone–butanol–ethanol) in a continuous bioreactor: impact of bleed and simultaneous product removal

Acetone butanol ethanol (ABE) was produced in an integrated continuous one-stage fermentation and gas stripping product recovery system using Clostridium beijerinckii BA101 and fermentation gases (CO₂ and H₂). In this system, the bioreactor was fed with a concentrated sugar solution (250–500 g L^?1 glucose). The bioreactor was bled semi-continuously to avoid accumulation of inhibitory chemicals and products. The continuous system was operated for 504 h (21 days) after which the fermentation was intentionally terminated. The bioreactor produced 461.3 g ABE from 1,125.0 g total sugar in 1 L culture volume as compared to a control batch process in which 18.4 g ABE was produced from 47.3 g sugar. These results demonstrate that ABE fermentation can be operated in an integrated continuous one-stage fermentation and product recovery system for a long period of time, if butanol and other microbial metabolites in the bioreactor are kept below threshold of toxicity.     

Ethanol production from sweet sorghum juice in batch and fed-batch fermentations by <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis>

Sweet sorghum juice supplemented with 0.5% ammonium sulphate was used as a substrate for ethanol production by Saccharomyces cerevisiae TISTR 5048. In batch fermentation, kinetic parameters for ethanol production depended on initial cell and sugar concentrations. The optimum initial cell and sugar concentrations in the batch fermentation were 1 × 10⁸ cells ml⁻¹ and 24 °Bx respectively. At these conditions, ethanol concentration produced (P), yield (Y _ps) and productivity (Q _p ) were 100 g l⁻¹, 0.42 g g⁻¹ and 1.67 g l⁻¹ h⁻¹ respectively. In fed-batch fermentation, the optimum substrate feeding strategy for ethanol production at the initial sugar concentration of 24 °Bx was one-time substrate feeding, where P, Y _ps and Q _p were 120 g l⁻¹, 0.48 g g⁻¹ and 1.11 g l⁻¹ h⁻¹ respectively. These findings suggest that fed-batch fermentation improves the efficiency of ethanol production in terms of ethanol concentration and product yield.     

Optimization of lactic acid production by immobilized <Emphasis Type="Italic">Lactococcus lactis</Emphasis> IO-1

Production of lactic acid from glucose by immobilized cells of Lactococcus lactis IO-1 was investigated using cells that had been immobilized by either entrapment in beads of alginate or encapsulation in microcapsules of alginate membrane. The fermentation process was optimized in shake flasks using the Taguchi method and then further assessed in a production bioreactor. The bioreactor consisted of a packed bed of immobilized cells and its operation involved recycling of the broth through the bed. Both batch and continuous modes of operation of the reactor were investigated. Microencapsulation proved to be the better method of immobilization. For microencapsulated cells at immobilized cell concentration of 5.3 g l⁻¹, the optimal production medium had the following initial concentrations of nutrients (g l⁻¹): glucose 45, yeast extract 10, beef extract 10, peptone 7.5 and calcium chloride 10 at an initial pH of 6.85. Under these conditions, at 37 °C, the volumetric productivity of lactic acid in shake flasks was 1.8 g l⁻¹ h⁻¹. Use of a packed bed of encapsulated cells with recycle of the broth through the bed, increased the volumetric productivity to 4.5 g l⁻¹ h⁻¹. The packed bed could be used in repeated batch runs to produce lactic acid.     

Production of <Emphasis Type="SmallCaps">d</Emphasis>-lactic acid from sugarcane molasses,sugarcane juice and sugar beet juice by <Emphasis Type="Italic">Lactobacillus delbrueckii</Emphasis>

Lactobacillus delbrueckii was grown on sugarcane molasses, sugarcane juice and sugar beet juice in batch fermentation at pH 6 and at 40°C. After 72 h, the lactic acid from 13% (w/v) sugarcane molasses (119 g total sugar l⁻¹) and sugarcane juice (133 g total sugar l⁻¹) was 107 g l⁻¹ and 120 g l⁻¹, respectively. With 10% (w/v) sugar beet juice (105 g total sugar l⁻¹), 84 g lactic acid l⁻¹ was produced. The optical purities of d-lactic acid from the feedstocks ranged from 97.2 to 98.3%.     

Recent advances in ABE fermentation: hyper-butanol producing Clostridium beijerinckii BA101

This is an overview of the mutant strain Clostridium beijerinckii BA101 which produces solvents (acetone–butanol–ethanol, ABE) at elevated levels. This organism expresses high levels of amylases when grown on starch. C. beijerinckii BA101 hydrolyzes starch effectively and produces solvent in the concentration range of 27–29 g l⁻¹. C. beijerinckii BA101 has been characterized for both substrate and butanol inhibition. Supplementing the fermentation medium (MP2) with sodium acetate enhances solvent production to 33 g l⁻¹. The results of studies utilizing commercial fermentation medium and pilot plant-scale reactors are consistent with the results using small-scale reactors. Pervaporation, a technique to recover solvents, has been applied to fed-batch reactors containing C. beijerinckii BA101, and solvent production as high as 165 g l⁻¹ has been achieved. Immobilization of C. beijerinckii BA101 by adsorption and use in a continuous reactor resulted in reactor productivity of 15.8 g l⁻¹ h⁻¹. Recent economic studies employing C. beijerinckii BA101 suggested that butanol can be produced at US$0.20–0.25 lb⁻¹ by employing batch fermentation and distillative recovery. Application of new technologies such as pervaporation, fed-batch culture, and immobilized cell reactors is expected to further reduce these prices. Journal of Industrial Microbiology & Biotechnology (2001) 27, 287–291. Received 12 September 2000/ Accepted in revised form 27 January 2001     

Controlling the oxidoreduction potential of the culture of <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis> leads to an earlier initiation of solventogenesis,thus increasing solvent productivity

Fermentative production of solvents (acetone, butanol, and ethanol) by Clostridium acetobutylicum is generally a biphasic process consisting of acidogenesis and solventogenesis. We report that the biphasic metabolism of C. acetobutylicum could be changed by oxidoreduction potential (ORP) regulation. When using air to control the ORP of the fermentation broth at −290 mV, an earlier initiation of solventogenesis was achieved. Solvent production reached 25.6 g l⁻¹ (2.8 g acetone l⁻¹, 16.8 g butanol l⁻¹, 6.0 g ethanol l⁻¹), a 35% increase compared with the ORP uncontrolled process. Metabolic flux analysis revealed that there was a general increase of the central carbon flux in the first 24 h of fermentation when ORP was controlled at −290 mV, compared with the control. Specifically, the solvent ratio (acetone:butanol:ethanol) was changed from 25:64:11 to 11:66:23 at ORP level of −290 mV, which might have resulted from the rigidity at acetyl-CoA node and the flexibility at acetoacetyl-CoA and butyryl-CoA nodes in response to ORP regulation.     

Modeling of <Emphasis Type="Italic">Fusarium redolens</Emphasis> Dzf2 mycelial growth kinetics and optimal fed-batch fermentation for beauvericin production

Beauvericin (BEA) is a cyclic hexadepsipeptide mycotoxin with notable phytotoxic and insecticidal activities. Fusarium redolens Dzf2 is a highly BEA-producing fungus isolated from a medicinal plant. The aim of the current study was to develop a simple and valid kinetic model for F. redolens Dzf2 mycelial growth and the optimal fed-batch operation for efficient BEA production. A modified Monod model with substrate (glucose) and product (BEA) inhibition was constructed based on the culture characteristics of F. redolens Dzf2 mycelia in a liquid medium. Model parameters were derived by simulation of the experimental data from batch culture. The model fitted closely with the experimental data over 20–50 g l⁻¹ glucose concentration range in batch fermentation. The kinetic model together with the stoichiometric relationships for biomass, substrate and product was applied to predict the optimal feeding scheme for fed-batch fermentation, leading to 54% higher BEA yield (299 mg l⁻¹) than in the batch culture (194 mg l⁻¹). The modified Monod model incorporating substrate and product inhibition was proven adequate for describing the growth kinetics of F. redolens Dzf2 mycelial culture at suitable but not excessive initial glucose levels in batch and fed-batch cultures.     

Production of <Emphasis Type="SmallCaps">l</Emphasis>-alanine by metabolically engineered <Emphasis Type="Italic">Escherichia coli</Emphasis>

Escherichia coli W was genetically engineered to produce l-alanine as the primary fermentation product from sugars by replacing the native d-lactate dehydrogenase of E. coli SZ194 with alanine dehydrogenase from Geobacillus stearothermophilus. As a result, the heterologous alanine dehydrogenase gene was integrated under the regulation of the native d-lactate dehydrogenase (ldhA) promoter. This homologous promoter is growth-regulated and provides high levels of expression during anaerobic fermentation. Strain XZ111 accumulated alanine as the primary product during glucose fermentation. The methylglyoxal synthase gene (mgsA) was deleted to eliminate low levels of lactate and improve growth, and the catabolic alanine racemase gene (dadX) was deleted to minimize conversion of l-alanine to d-alanine. In these strains, reduced nicotinamide adenine dinucleotide oxidation during alanine biosynthesis is obligately linked to adenosine triphosphate production and cell growth. This linkage provided a basis for metabolic evolution where selection for improvements in growth coselected for increased glycolytic flux and alanine production. The resulting strain, XZ132, produced 1,279 mmol alanine from 120 g l⁻¹ glucose within 48 h during batch fermentation in the mineral salts medium. The alanine yield was 95% on a weight basis (g g⁻¹ glucose) with a chiral purity greater than 99.5% l-alanine. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.