Atomic force microscope visualization of lipid bilayer degradation due to action of phospholipase A2 and Humicola lanuginosa lipase

An important application of liquid cell Atomic Force Microscopy (AFM) is the study of enzyme structure and behaviour in organized molecular media that mimic in-vivo systems. In this study we demonstrate the use of AFM as a tool to study the kinetics of lipolytic enzyme reactions occurring at the surface of a supported lipid bilayer. In particular, the time course of the degradation of lipid bilayers by Phospholipase A(2) (PLA(2)) and Humicola Lanuginosa Lipase (HLL) has been investigated. Contact mode imaging allows visualization of enzyme activity on the substrate with high lateral resolution. Lipid bilayers were prepared by the Langmuir-Blodgett technique and transferred to an AFM liquid cell. Following injection of the enzyme into the liquid cell, a sequence of images was acquired at regular time intervals to allow the identification of substrate structure, preferred sites of enzyme activation, and enzyme reaction rates.     

Influence of product phase separation on phospholipase A(2) hydrolysis of supported phospholipid bilayers studied by force microscopy

In situ atomic force microscopy studies reveal a marked influence of the initial presence of hydrolysis products on the hydrolysis of supported phospholipid bilayers by phospholipase A(2). By analysis of the nano-scale topography of a number of supported bilayers with different initial product concentrations, made by Langmuir-Blodgett deposition, we show that small depressions enriched in products are efficiently promoting enzyme degradation of the bilayer. These small depressions, which are indicative of phase separation, are initially present in samples with 75% products. The kinetics of phospholipase A(2) exhibit under certain conditions an initial phase of slow hydrolysis, termed the latency phase, followed by a marked increase in the hydrolysis rate. The appearance of the phase-separated bilayer is strikingly similar to that of bilayers at the end of the latency phase. By analysis of individual nano-scale defects we illustrate a quantitative difference in the growth rates of defects caused by product aggregation and other structural defects. This difference shows for the first time how the enzyme prefers one type of defect to another.     

Humicola lanuginosa lipase hydrolysis of mono-oleoyl-rac-glycerol at the lipid-water interface observed by atomic force microscopy

A new type of planar lipid substrate for Humicola lanuginosa lipase (HLL) has been prepared by depositing a monolayer of 1-mono-oleoyl-rac-glycerol (MOG) on top of a monolayer of dipalmitoyl-phosphatidylcholine (DPPC) on mica by the Langmuir-Blodgett (LB) technique. The bilayer was subsequently exposed to HLL in a liquid cell of an atomic force microscope (AFM) allowing the time course of the lipolytic degradation to be observed. By analysing a series of AFM images, we find that enzymes are preferentially activated at the edge of nano-scale defects present in the bilayer prior to enzyme injection, while defect-free areas of the substrate are surprisingly stable towards enzyme degradation. The initial rate of hydrolysis is found to be proportional to the perimeter length, P, of the initial nano-scale defects as well as the bulk enzyme concentration, c(HLL); d(lipid)/dt=k P c(HLL). We estimate the specific rate of MOG hydrolysis by HLL to be 2.5x10(4) MOG molecules/(minute x molecule of HLL).     

Lag-burst kinetics in phospholipase A(2) hydrolysis of DPPC bilayers visualized by atomic force microscopy.

The lag-burst phenomenon in the phospholipase A(2) mediated hydrolysis of phospholipid bilayers is for the first time demonstrated in an atomic force microscopy (AFM) study. Simultaneous AFM measurements of the degree of bilayer degradation and the physical-chemical state of the membrane reveals growing nanoscale indentations in the membrane during the lag phase. It is argued that these indentations are domains of hydrolysis products (lysoPC/PC) which eventually trigger the burst. The rate of the rapid hydrolysis following the burst is found to be proportional to the length of the edge between membrane adsorbed and desorbed to the mica base. The observed maximal rate of membrane degradation is approx. 0.2 mmol lipid/min/mol lipase in solution.     

Atomic force microscope visualization of lipid bilayer degradation due to action of phospholipase A2 and Humicola lanuginosa lipase

An important application of liquid cell Atomic Force Microscopy (AFM) is the study of enzyme structure and behaviour in organized molecular media that mimic in-vivo systems. In this study we demonstrate the use of AFM as a tool to study the kinetics of lipolytic enzyme reactions occurring at the surface of a supported lipid bilayer. In particular, the time course of the degradation of lipid bilayers by Phospholipase A₂ (PLA₂) and Humicola Lanuginosa Lipase (HLL) has been investigated. Contact mode imaging allows visualization of enzyme activity on the substrate with high lateral resolution. Lipid bilayers were prepared by the Langmuir-Blodgett technique and transferred to an AFM liquid cell. Following injection of the enzyme into the liquid cell, a sequence of images was acquired at regular time intervals to allow the identification of substrate structure, preferred sites of enzyme activation, and enzyme reaction rates.     

Supported planar bilayer formation by vesicle fusion: the interaction of phospholipid vesicles with surfaces and the effect of gramicidin on bilayer properties using atomic force microscopy

We have used magnetic alternating current mode atomic force microscopy (MAC-AFM) to investigate the formation of supported phospholipid bilayers (SPB) by the method of vesicle fusion. The systems studied were dioleoylphosphatidylcholine (DOPC) on mica and mica modified with 3-aminopropyl-triethoxy-silane (APTES), and DOPC vesicles with gramicidin incorporated on mica and APTES-modified mica. The AFM images reveal three stages of bilayer formation: localized disklike features that are single bilayer footprints of the vesicles, partial continuous coverage, and finally complete bilayer formation. The mechanism of supported phospholipid bilayers formation is the fusion of proximal vesicles, rather than surface disk migration. This mechanism does not appear to be affected by incorporation of gramicidin or by surface modification. Once formed, the bilayer develops circular defects one bilayer deep. These defects grow in size and number until a dynamic equilibrium is reached.     

Correlation of AFM and SFA measurements concerning the stability of supported lipid bilayers

Phospholipid bilayers were studied by means of atomic force microscopy (AFM) and a surface force apparatus (SFA). The stability of the supported bilayers was described by the amount of irregularities in the topography of the membrane by means of AFM and by the occurrence of hemifusion in the SFA, which is an indicator of defective bilayers. The bilayers, composed of lipids having the same headgroup but different chain lengths in the two leaflets, were prepared by Langmuir-Blodgett deposition and transferred at different surface pressures. The topography of the supported bilayers in aqueous solution, as imaged by AFM, revealed an increasing number of defects in the supported lipid membranes with decreased deposition pressure of the outer lipid layer. These defects, which appeared in the form of monolayer and bilayer (self-assembled) thick holes within the membrane, were energetically favorable over an evenly depleted bilayer. We found that the quantity of these defects (holes of 相似文献   

Enzyme-catalyzed hydrolysis of the supported phospholipid bilayers studied by atomic force microscopy

Atomic force microscopy (AFM) is employed to reveal the morphological changes of the supported phospholipid bilayers hydrolyzed by a phospholipase A₂ (PLA₂) enzyme in a buffer solution at room temperature. Based on the high catalytic selectivity of PLA₂ toward l-enantiomer phospholipids, five kinds of supported bilayers made of l- and d-dipalmitoylphosphatidylcholines (DPPC), including l-DPPC (upper leaflet adjacent to solution)/l-DPPC (bottom leaflet) (or l/l in short), l/d, d/l, d/d, and racemic ld/ld, were prepared on a mica surface in gel-phase, to explicate the kinetics and mechanism of the enzyme-induced hydrolysis reaction in detail. AFM observations for the l/l bilayer show that the hydrolysis rate for l-DPPC is significantly increased by PLA₂ and most of the hydrolysis products desorb from substrate surface in 40 min. As d-enantiomers are included in the bilayer, the hydrolysis rate is largely decreased in comparison with the l/l bilayer. The time used to hydrolyze the as-prepared bilayers by PLA₂ increases in the sequence of l/l, l/d, ld/ld, and d/l (d/d is inert to the enzyme action). d-enantiomers in the enantiomer hybrid bilayers remain on the mica surface at the end of the hydrolysis reaction. It was confirmed that the hydrolysis reaction catalyzed by PLA₂ preferentially occurs at the edges of pits or defects on the bilayer surface. The bilayer structures are preserved during the hydrolysis process. Based on these observations, a novel kinetics model is proposed to quantitatively account for the PLA₂-catalyzed hydrolysis of the supported phospholipid bilayers. The model simulation demonstrates that PLA₂ mainly binds with lipids at the perimeter of defects in the upper leaflet and leads to a hydrolysis reaction, yielding species soluble to the solution phase. The lipid molecules underneath subsequently flip up to the upper leaflet to maintain the hydrophilicity of the bilayer structure. Our analysis shows that d-enantiomers in the hybrid bilayers considerably reduce the hydrolysis rate by its ineffective binding with PLA₂.     

Enzymatic degradation of monolayer for poly(lactide) revealed by real-time atomic force microscopy: effects of stereochemical structure, molecular weight, and molecular branches on hydrolysis rates

The influences of the stereochemical structure, the molecular weight, and the number of molecular branches for poly(lactide) (PLA) on enzymatic hydrolysis rates of PLA monolayers were studied by atomic force microscopy (AFM) and the Langmuir-Blodgett (LB) technique. Monolayers of six kinds of PLA with different molecular weights, stereochemical structure, and numbers of molecular branches were prepared by LB techniques and then characterized by AFM in air. The PLA molecules covered homogeneously with a silicon substrate and did not form lamellar crystals in the monolayer. We determined the initial hydrolysis rate of PLA monolayers in presence of proteinase K by volumetric analysis from the continuous AFM height images. The presence of D-lactyl unit reduced the hydrolysis rate of the monolayer. The hydrolysis rate for the linear PLLA samples increased with a decrease in the molecular weight. In contrast, the rates of erosion for branched PLLA monolayers were independent of the molecular weight of samples. The erosion rate of branched PLLA monolayers was found to be dependent on the average molecular weight of PLLA segment in branched molecules, not on the overall molecular weight of samples. From these results, furthermore, the hydrolysis mode of PLAs by proteinase K is discussed.     

Phospholipase A(2) activity towards vesicles of DPPC and DMPC-DSPC containing small amounts of SMPC.

Phospholipase A(2) (PLA(2)) is an interfacially active enzyme whose hydrolytic activity is known to be enhanced in one-component phospholipid bilayer substrates exhibiting dynamic micro-heterogeneity. In this study the activity of PLA(2) towards large unilamellar vesicles composed of DPPC:SMPC and DMPC:DSPC:SMPC is investigated using fluorescence and HPLC techniques. Phase diagrams of the mixtures are established by differential scanning calorimetry and the PLA(2) activity, monitored by the lag time, is correlated with the phase behavior of the mixtures. In addition, the degree of lipid hydrolysis in the DMPC:DSPC:SMPC lipid mixtures is detected by HPLC. The PLA(2) activity is found to be significantly increased in the temperature range of the coexistence region where the lipid mixtures exhibit lateral gel-fluid phase separation. Furthermore, in the entire temperature range it is demonstrated that PLA(2) preferentially hydrolyzes the short chain DMPC lipid. This discriminative effect becomes less pronounced when the asymmetric lipid SMPC is present in the lipid substrate. Inclusion of SMPC into either DPPC or DMPC:DSPC vesicles prolongs the lag time. The results clearly show that the PLA(2) activity is significantly enhanced by lipid bilayer micro-heterogeneity in both one-component and multi-component lipid bilayer substrates. The PLA(2) activity measurements are discussed in terms of dynamic gel-fluid lipid domain formation due to density fluctuations and static lipid domain formation due to gel-fluid phase separation.     

Dibucaine effects on structural and elastic properties of lipid bilayers

In this work we report the interaction effects of the local anesthetic dibucaine (DBC) with lipid patches in model membranes by Atomic Force Microscopy (AFM). Supported lipid bilayers (egg phosphatidylcholine, EPC and dimyristoylphosphatidylcholine, DMPC) were prepared by fusion of unilamellar vesicles on mica and imaged in aqueous media. The AFM images show irregularly distributed and sized EPC patches on mica. On the other hand DMPC formation presents extensive bilayer regions on top of which multibilayer patches are formed. In the presence of DBC we observed a progressive disruption of these patches, but for DMPC bilayers this process occurred more slowly than for EPC. In both cases, phase images show the formation of small structures on the bilayer surface suggesting an effect on the elastic properties of the bilayers when DBC is present. Dynamic surface tension and dilatational surface elasticity measurements of EPC and DMPC monolayers in the presence of DBC by the pendant drop technique were also performed, in order to elucidate these results. The curve of lipid monolayer elasticity versus DBC concentration, for both EPC and DMPC cases, shows a maximum for the surface elasticity modulus at the same concentration where we observed the disruption of the bilayer by AFM. Our results suggest that changes in the local curvature of the bilayer induced by DBC could explain the anesthetic action in membranes.     

Phase behavior and nanoscale structure of phospholipid membranes incorporated with acylated C14-peptides

The thermotropic phase behavior and lateral structure of dipalmitoylphosphatidylcholine (DPPC) lipid bilayers containing an acylated peptide has been characterized by differential scanning calorimetry (DSC) on vesicles and atomic force microscopy (AFM) on mica-supported bilayers. The acylated peptide, which is a synthetic decapeptide N-terminally linked to a C14 acyl chain (C14-peptide), is incorporated into DPPC bilayers in amounts ranging from 0-20 mol %. The calorimetric scans of the two-component system demonstrate a distinct influence of the C14-peptide on the lipid bilayer thermodynamics. This is manifested as a concentration-dependent downshift of both the main phase transition and the pretransition. In addition, the main phase transition peak is significantly broadened, indicating phase coexistence. In the AFM imaging scans we found that the C14-peptide, when added to supported gel phase DPPC bilayers, inserts preferentially into preexisting defect regions and has a noticeable influence on the organization of the surrounding lipids. The presence of the C14-peptide gives rise to a laterally heterogeneous bilayer structure with coexisting lipid domains characterized by a 10 A height difference. The AFM images also show that the appearance of the ripple phase of the DPPC lipid bilayers is unaffected by the C14-peptide. The experimental results are supported by molecular dynamics simulations, which show that the C14-peptide has a disordering effect on the lipid acyl chains and causes a lateral expansion of the lipid bilayer. These effects are most pronounced for gel-like bilayer structures and support the observed downshift in the phase-transition temperature. Moreover, the molecular dynamics data indicate a tendency of a tryptophan residue in the peptide sequence to position itself in the bilayer headgroup region.     

Enzymatic generation of ceramide induces membrane restructuring: Correlated AFM and fluorescence imaging of supported bilayers

The effect of enzymatic generation of ceramide on phase separated bilayers with a mixture of co-existing fluid and liquid-ordered phases has been examined using a combination of atomic force microscopy (AFM) and fluorescence imaging. Supported lipid bilayers prepared from a DOPC/sphingomyelin/cholesterol mixture were imaged prior to, during and after incubation with sphingomyelinase by total internal reflection fluorescence (TIRF) microscopy. Enzyme treatment resulted in the growth of large dye-excluded regions. The growth kinetics for these patches are consistent with activity of a variable number of enzyme molecules in different regions of the bilayer. Correlated AFM and fluorescence imaging shows that some of the large dye-excluded patches form around the original liquid-ordered domains, which become heterogeneous in height with many raised ceramide-rich regions around their periphery. However, some of the dye-excluded patches correspond to areas of the bilayer where the initial domains have largely or partially disappeared. The dye-excluded patches observed by fluorescence are shown to be areas of increased adhesion in lateral deflection AFM images and are postulated to form by incorporation of both cholesterol and ceramide in the original fluid phase and to vary in composition throughout the bilayer. This is evident from the observation that the dye-excluded areas are all detected as areas of increased friction, but do not always show a distinct height difference in topographic images. These results highlight the utility of a multi-modal imaging approach for understanding the complex membrane restructuring that occurs upon enzymatic generation of ceramide.     

Compatibilization effect of poly(epsilon-caprolactone)-b-poly(ethylene glycol) block copolymers and phase morphology analysis in immiscible poly(lactide)/poly(epsilon-caprolactone) blends

The miscibility and phase behavior of two stereoisomer forms of poly(lactide) (PLA: poly (L-lactide) (PLLA) and poly(DL-lactide) (PDLLA)) blends with poly(epsilon-caprolactone)-b-poly(ethylene glycol) (PCL-b-PEG) and PCL-b-monomethoxy-PEG (PCL-b-MPEG) block copolymers have been investigated by differential scanning calorimetry (DSC). The DSC thermal behavior of both the blend systems revealed that PLA is miscible with the PEG segment phase of PCL-b-(M)PEG but is still immiscible with its PCL segment phase although PCL was block-copolymerized with PEG. On the basis of these results, PCL-b-PEG was added as a compatibilizer to PLA/PCL binary blends. The improvement in mechanical properties of PLA/PCL blends was achieved as anticipated upon the addition of PCL-b-PEG. In addition, atomic force microscopy (AFM) measurements have been performed in order to study the compositional synergism to be observed in mechanical tests. AFM observations of the morphological dependency on blend composition indicate that PLA/PCL blends are immiscible but compatible to some extent and that synergism of compatibilizing may be maximized in the compositional blend ratio before apparent phase separation and coarsening.     

Advances in the characterization of supported lipid films with the atomic force microscope

During the past decade, the atomic force microscope (AFM) has become a key technique in biochemistry and biophysics to characterize supported lipid films, as testified by the continuous growth in the number of papers published in the field. The unique capabilities of AFM are: (i) capacity to probe, in real time and in aqueous environment, the surface structure of lipid films; (ii) ability to directly measure physical properties at high spatial resolution; (iii) possibility to modify the film structure and biophysical processes in a controlled way. Such experiments, published up to June 2000, are the focus of the present review. First, we provide a general introduction on the preparation and characterization of supported lipid films as well as on the principles of AFM. The section 'Structural properties' focuses on the various applications of AFM for characterizing the structure of supported lipid films: visualization of molecular structure, formation of structural defects, effect of external agents, formation of supported films, organization of phase-separated films (coexistence region, mixed films) and, finally, the use of supported lipid bilayers for anchoring biomolecules such as DNA, enzymes and crystalline protein arrays. The section 'Physical properties' introduces the principles of force measurements by AFM, interpretation of these measurements and their recent application to supported lipid films and related structures. Finally, we highlight the major achievements brought by the technique and some of the current limitations.     

AFM study of the thermotropic behaviour of supported DPPC bilayers with and without the model peptide WALP23

Temperature-controlled Atomic Force Microscopy (TC-AFM) in Contact Mode is used here to directly image the mechanisms by which melting and crystallization of supported, hydrated DPPC bilayers proceed in the presence and absence of the model peptide WALP23. Melting from the gel L_β′ to the liquid-crystalline L_α phase starts at pre-existing line-type packing defects (grain boundaries) in absence of the peptide. The exact transition temperature is shown to be influenced by the magnitude of the force exerted by the AFM probe on the bilayer, but is higher than the main transition temperature of non-supported DPPC vesicles in all cases due to bilayer–substrate interactions. Cooling of the fluid L_α bilayer shows the formation of the line-type defects at the borders between different gel-phase regions that originate from different nuclei. The number of these defects depends directly on the rate of cooling through the transition, as predicted by classical nucleation theory.The presence of the transmembrane, synthetic model peptide WALP23 is known to give rise to heterogeneity in the bilayer as microdomains with a striped appearance are formed in the DPPC bilayer. This striated phase consists of alternating lines of lipids and peptide. It is shown here that melting starts with the peptide-associated lipids in the domains, whose melting temperature is lowered by 0.8–2.0 °C compared to the remaining, peptide-free parts of the bilayer. The stabilization of the fluid phase is ascribed to adaptations of the lipids to the shorter peptide. The lipids not associated with the peptide melt at the same temperature as those in the pure DPPC supported bilayer.     

A morphological analysis of growth cones of DRG neurons combining Atomic Force and Confocal Microscopy

We have analyzed the morphology of growth cones of differentiating neurons from rat dorsal root ganglia (DRG) with conventional Laser Scanning Confocal Microscopy (LSCM) and Atomic Force Microscopy (AFM). Images of immunofluorescent DRG growth cones colabeled for actin and tubulin were superimposed to images obtained with AFM at different scanning forces. In order to reduce changes of the image surface caused by the pressure of the AFM tip, we have developed a procedure to obtain 0 pN AFM images. Further analysis of these images revealed topographical structures with nanoscale dimensions, referred to as “invaginations” or “holes”. These holes had an area varying from 0.01 to 3.5 μm² with a depth varying from 2 to 178 nm. Comparative analysis with LSCM images showed that these holes correspond to regions where staining of both actin and tubulin was negligible. Filopodia height varied from 40 to 270 nm and their diameter from 113 to 887 nm. These results show that the combination of LSCM and AFM reveal structural details with a nanoscale dimension of DRG growth cones, difficult to resolve with conventional microscopy.     

Biodegradation of poly(l-lactide)

The biodegradation of poly(L-lactide) (PLA) is reviewed. The important role of actinomycetes in PLA degradation is emphasized. These PLA-degrading actinomycetes belong phylogenetically to the Pseudonocardiaceae family and related genera, including Amycolatopsis, Lentzea, Streptoalloteichus, Kibdelosporangium and Saccharothrix. A PLA-degrading enzyme purified from an isolated Amycolatopsis strain-41 has substrate specificity on PLA higher than proteinase K. The application of these strains and their enzymes can be effectively used for biological treatment of plastic wastes containing PLA.     

Preferential accumulation of Abeta(1-42) on gel phase domains of lipid bilayers: an AFM and fluorescence study

Peptide-membrane interactions have been implicated in both the toxicity and aggregation of beta-amyloid (Abeta) peptides. Recent studies have provided evidence for the involvement of liquid-ordered membrane domains known as lipid rafts in the formation and aggregation of Abeta. As a model, we have examined the interaction of Abeta(1-42) with phase separated DOPC/DPPC lipid bilayers using a combination of atomic force microscopy (AFM) and total internal reflection fluorescence microscopy (TIRF). AFM images show that addition of Abeta to preformed supported bilayers leads to accumulation of small peptide aggregates exclusively on the gel phase DPPC domains. Initial aggregates are observed approximately 90 min after peptide addition and increase in diameter to 45-150 nm within 24 h. TIRF studies with a mixture of Abeta and Abeta-Fl demonstrate that accumulation of the peptide on the gel phase domains occurs as early as 15 min after Abeta addition and is maintained for over 24 h. By contrast, Abeta is randomly distributed throughout both fluid and gel phases when the peptide is reconstituted into DOPC/DPPC vesicles prior to formation of a supported bilayer. The preferential accumulation of Abeta on DPPC domains suggests that rigid domains may act as platforms to concentrate peptide and enhance its aggregation and may be relevant to the postulated involvement of lipid rafts in modulating Abeta activity in vivo.     

Growth of cationic lipid toward bilayer lipid membrane by solution spreading: scanning probe microscopy study

The growth of cationic lipid dioctadecyldimethylammonium bromide (DODAB) toward bilayer lipid membrane (BLM) by solution spreading on cleaved mica surface was studied by atomic force microscopy (AFM). Bilayer of DODAB was formed by exposing mica to a solution of DODAB in chloroform and subsequently immersing into potassium chloride solution for film developing. AFM studies showed that at the initial stage of the growth, the adsorbed molecules exhibited the small fractal-like aggregates. These aggregates grew up and expanded laterally into larger patches with time and experienced from monolayer to bilayer, finally a close-packed bilayer film (5.4+/-0.2 nm) was approached. AFM results of the film growth process indicated a growth mechanism of nucleation, growth and coalescence of dense submonolayer, it revealed the direct information about the film morphology and confirmed that solution spreading was an effective technique to prepare a cationic bilayer in a short time.