Use of ATP to characterize biomass viability in freely suspended and immobilized cell bioreactors

This work describes investigations into the viability of cells growing on 3,4-dichloroaniline (34DCA). Two bioreactors are employed for microbial growth, a continuous stirred tank (CST) bioreactor with a 2-L working volume, and a three-phase air lift (TPAL) bioreactor with a 3-L working volume. Experiments have been performed at several dilution rates between 0.027 and 0.115 h(-1) in the CST bioreactor and between 0.111 and 0.500 h(-1) in the TPAL bioreactor. The specific ATP concentration was calculated at each dilution rate in the suspended biomass in both bioreactors as well as in the immobilized biomass in the TPAL bioreactor. The ATP was extracted from the cells using boiling tris-EDTA buffer (pH 7.75), and the quantity determined using a firefly (bioluminescence) technique. The cultures were inspected under an electron microscope to monitor compositional changes. Results from the CST bioreactor showed that the biomass-specific ATP concentration increases from 0.44 to 1.86 mg ATP g(-1) dry weight (dw) as dilution rate increases from 0.027 to 0.115 h(-1). At this upper dilution rate the cells were washed out. The specific ATP concentration reached a limiting average value of 1.73 mg ATP g(-1) dw, which is assumed to be the quantity of ATP in 100% viable biomass. In the TPAL bioreactor, the ATP level increased with dilution rate in both the immobilized and suspended biomass. The specific ATP concentration in the immobilized biomass increased from approximately 0.051 mg ATP g(-1) dw at dilution rates between 0.111 and 0.200 h(-1) to approximately 0.119 mg ATP g(-1) dw at dilution rates between 0.300 and 0.500 h(-1). This indicates that the immobilized biomass contained a viable cell fraction of around 5%. Based on these results, kinetic data for freely suspended cells should not be applied to the modeling of immobilized cell systems on the assumption that immobilized biomass is 100% viable. (c) 1993 John Wiley & Sons, Inc.     

Optimization and control of perfusion cultures using a viable cell probe and cell specific perfusion rates

Consistent perfusion culture production requires reliable cell retention and control of feed rates. An on-line cell probe based on capacitance was used to assay viable biomass concentrations. A constant cell specific perfusion rate controlled medium feed rates with a bioreactor cell concentration of ∼5 × 10⁶ cells mL^-1. Perfusion feeding was automatically adjusted based on the cell concentration signal from the on-line biomass sensor. Cell specific perfusion rates were varied over a range of 0.05 to 0.4 nL cell^-1 day^-1. Pseudo-steady-state bioreactor indices (concentrations, cellular rates and yields) were correlated to cell specific perfusion rates investigated to maximize recombinant protein production from a Chinese hamster ovary cell line. The tissue-type plasminogen activator concentration was maximized (∼40 mg L^-1) at 0.2 nL cell^-1 day^-1. The volumetric protein productivity (∼60 mg L^-1 day^-1 was maximized above 0.3 nL cell^-1 day^-1. The use of cell specific perfusion rates provided a straightforward basis for controlling, modeling and optimizing perfusion cultures. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of particle loading on GM-CSF production by Saccharomyces cerevisiae in a three-phase fluidized bed bioreactor

Continuous production of a recombinant murine granulocyte-macrophage colony-stimulating factor (MuGM-CSF) by immobilized yeast cells, Saccharomyces cerevisiae strain XV2181 (a/a, Trp1) containing plasmid palphaADH2, in a fluidized bed bioreactor was studied at a 0.03 h(-1) dilution rate and various particle loading rates ranging from 5% to 33% (v/v). Cells were immobilized on porous glass beads fluidized in an air-lift draft tube bioreactor. A selective medium containing glucose was used to start up the reactor. After reaching a stable cell concentration, the reactor feed was switched to a rich, nonselective medium containing ethanol as the carbon source for GM-CSF production. GM-CSF production increased initially and then dropped gradually to a stable level. During the same period, the fraction of plasmid-carrying cells declined continuously to a lower level, depending on the particle loading. The relatively stable GM-CSF production, despite the large decline in the fraction of plasmid-carrying cells, was attributed to cell immobilization. As the particle loading rate increased, the plasmid stability also increased. Also, as the particle loading increased from 5% to 33%, total cell density in the bioreactor increased from 16 to 36 g/L, and reactor volumetric productivity increased from 0.36 to 1.31 mg/L.h. However, the specific productivity of plasmid-carrying cells decreased from 0.55 to 0.07 mg/L.g cell. The decreased specific productivity at higher particle loading rates was attributed to reduced growth efficiency caused by nutrient limitations at higher cell densities. Both the reactor productivity and specific cell productivity increased by two- to threefold or higher when the dilution rate was increased from 0.03 to 0.07 h(-1). (c) 1996 John Wiley & Sons, Inc.     

Empirical model for the autotrophic biodegradation of thiocyanate in an activated sludge reactor

AIMS: The aim of this investigation was to develop an empirical model for the autotrophic biodegradation of thiocyanate using an activated sludge reactor. METHODS AND RESULTS: The methods used for this purpose included the use of a laboratory scale activated sludge reactor unit using thiocyante feed concentrations from 200 to 550 mg x l(-1). Reactor effluent concentrations of <1 mg x l(-1) thiocyanate were consistently achieved for the entire duration of the investigation at a hydraulic retention time of 8 h, solids (biomass) retention of 18 h and biomass (dry weight) concentrations ranging from 2 to 4 g x l(-1). A biomass specific degradation rate factor was used to relate thiocyanate degradation in the reactor to the prevailing biomass and thiocyanate feed concentrations. A maximum biomass specific degradation rate of 16 mg(-1) x g(-1) x h(-1) (mg thiocyanate consumed per gram biomass per hour) was achieved at a thiocyanate feed concentration of 550 mg x l(-1). The overall yield coefficient was found to be 0.086 (biomass dry weight produced per mass of thiocyanate consumed). CONCLUSION: Using the results generated by this investigation, an empirical model was developed, based on thiocyanate feed concentration and reactor biomass concentration, to calculate the required absolute hydraulic retention time at which a single-stage continuously stirred tank activated sludge reactor could be operated in order to achieve an effluent concentration of <1 mg x l(-1). The use of an empirical model rather than a mechanistic-based kinetic model was proposed due to the low prevailing thiocyanate concentrations in the reactor. SIGNIFICANCE AND IMPACT OF THE STUDY: These results represent the first empirical model, based on a comprehensive data set, that could be used for the design of thiocyanate-degrading activated sludge systems.     

Oscillatory behavior of Saccharomyces cerevisiae in continuous culture: II. Analysis of cell synchronization and metabolism

Sustained oscillations of biomass, ethanol, and ammonium concentrations, specific growth rate, and specific uptake rates of ethanol, ammonium, and oxygen were found in continuous cultures of Saccharomyces cerevisiae under controlled dissolved oxygen (DO), pH, and temperature conditions. The period of oscillations was approximately 2.5-3 h at a pH of 5.5 and 2-2.5 h at a pH of 6.5. Oscillations were observed only under conditions of low carbon (glucose below the minimum detectable level), nitrogen nutrient (ammonium concentration varied between 0.00001 and 0.0015M), and ethanol concentration (0.002-0.085 g/L) in the bioreactor.The oscillatory behavior at pH 5.5 was also characterized by partially synchronized cell growth and reproduction. Not only did the total percentage of budding cells oscillate with the same period as observed for the global biomass and nutrient concentrations, but the peaks in the individual subpopulations of initial budding, middle budding, and late budding cells appeared sequentially during the oscillation period. This provides strong evidence of the hypothesis that variations in metabolism during different periods in the cell cycle of a partially synchronized cell population are responsible for the observed oscillatory bioreactor behavior.The specific nutrient uptake rates for ammonium and oxygen as well as the net specific ethanol uptake rate oscillated with the same period as the biomass oscillations. These results show a dramatic increase in the ammonium and oxygen consumption rates prior to the initial budding of the synchronized subpopulation and a decrease in these rates during the late budding phase. At a pH of 5.5, the late budding phase is characterized by high specific ethanol productivity; however, the ethanol productivity lags the late budding phase at a pH pf 6.5. The observed time-varying metabolism in the oscillatory operating regime appears to be the result of the metabolic changes which occur during the cell cycle. Models which can predict the oscillatory biomass concentration and nutrient levels in this regime must be capable of predicting the concentrations and metabolic rates of the subpopulations as well.     

Continuous ethanol production from Jerusalem artichoke tubers. I. Use of free cells of Kluyveromyces marxianus

The Continuous fermentation of Jerusalem artichoke juice to ethanol by free cells of Kluyveromyces marxianus UCD (FST) 55-82 has been studied in a continuous-stirred-tank bioreactor at 35 degrees C and pH 4.6. A maximum yield of 90% of the theoretical was obtained at a dilution rate of 0.05 h(-1). About 95% of the sugars were utilized at dilution rates lower than 0.15 h(-1). Volumetric ethanol productivity and volumetric biomass productivity reached maximum values of 7 g ETOH/L/h and 0.6 g dry wt/L/h, respectively, at a dilution rate of 0.2 h(-1). The maintenance energy coefficient for K. marxianus culture was found to be 0.46 g sugar/g biomass/h/ Oscillatory behavior was following a change in dilution rate from a previous steady state and from batch to continuous culture. Values of specific ethanol production rate and specific sugar uptake were found to increase almost linearly with the increase of the dilution rate. The maximum specific ethanol production rate and maximum specific sugar uptake rate were found to be 2.6 g ethanol/g/ cell/h and 7.9 sugars/g cell/h, respectively. Washout occurred at a dilution rate of 0.41 h(-1).     

Continuous ethanol production from Jerusalem artichoke tubers. II. Use of immobilized cells of Kluyveromyces marxianus

Kluyveromyces marxianus UCD (FST) 55-82 cells were immobilized in Na alginate beads and used in a packed-bed bioreactor system for the continuous production of ethanol from the extract of Jerusalem artichoke tubers. Volumetric ethanol productivities of 104 and 80 g ethanol/ L/h were obtained at 80 and 92% sugar utilization, respectively. The maximum volumetric ethanol productivity of the immobilized cell bioreactor system was found to be 15 times higher than that of an ordinary-stirred-tank (CST) bioreactor using cells of K. marxianus. The immobilized cell bioreactor system was operated continuously at a constant dilution rate of 0.66 h(-1) for 12 days resulting in only an 8% loss of the original immobilized cell activity, which corresponds to an estimated half-life of ca. 72 days. The maximum specific ethanol productivity and maximum specific sugar uptake rate of the immobilized cells were found to be 0.55 g ethanol/g/biomass/h and 1.21 g sugars/g biomass/h, respectively.     

Effect of feed and bleed rate on hybridoma cells in an acoustic perfusion bioreactor: part I. Cell density, viability, and cell-cycle distribution

For the development of optimal perfusion processes the effect of the feed and bleed rate on cell growth in a perfusion bioreactor was studied. The viable-cell density, viability, growth, death, and lysis rate and cell-cycle distribution of a hybridoma cell line producing an IgG1 were studied over a range of specific feed and bleed rates. It was found that the feed and bleed rates applied in the different cultures could be divided into two regions based on the viable-cell density and cell-cycle distribution. The cultures in the first region, low feed rates (0.5 and 1.0 d(-1)) combined with low bleed rates (0.05 and 0.10 d(-1)), were nutrient-limited, as an increase in the feed rate resulted in an increase in the viable-cell density. The cultures in the second region, high feed and bleed rates, were nonnutrient-limited. In this region the viable-cell density decreased more or less linearly with an increase in the bleed rate and was independent of the feed rate. This suggests that the cells were limited by a cell-related factor. Comparison of Trypan-blue dye-exclusion measurements and lactate-dehydrogenase activity measurements revealed that cell lysis was not negligible in this bioreactor set-up. Therefore, lactate-dehydrogenase activity measurements were essential to measure the death rate accurately. The specific growth rate was nearly constant for all tested conditions. The viability increased with an increase of the bleed rate and was independent of the feed rate. Furthermore, the specific productivity of monoclonal antibody was constant under all tested conditions. For the optimal design of a perfusion process it should first be established whether viability is an important parameter. If not, a bleed rate as low as possible should be chosen. If low viabilities are to be avoided, the bleed rate chosen should be higher, with the value depending on the desired viability. Next, the feed rate should be set at such a rate that the cells are just in the nonnutrient-limited region.     

Cultivation of microplantlets derived from the marine red alga Agardhiella subulata in a stirred tank photobioreactor

Macrophytic marine red algae are a diverse source of bioactive natural compounds. "Microplantlet" suspension cultures established from red algae are potential platforms for biosynthesis of these compounds, provided suitable bioreactor configurations for mass culture can be identified. The stirred tank bioreactor offers high rates of gas-liquid mass transfer, which may facilitate the delivery of the CO(2) in the aeration gas to the phototrophic microplantlet suspension culture. Therefore, the effects of impeller speed and CO(2) delivery on the long-term production of microplantlet biomass of the model red alga Agardhiella subulata was studied within a stirred tank photobioreactor equipped with a paddle blade impeller (D(i)/D(T) = 0.5). Nutrient medium replacement was required for sustained biomass production, and the biomass yield coefficient based on nitrate consumption was 1.08 +/- 0.09 g dry biomass per mmol N consumed. Biomass production went through two exponential phases of growth, followed by a CO(2) delivery limited growth phase. The CO(2)-limited growth phase was observed only if the specific growth rate in the second exponential phase of growth was at least 0.03 day(-)(1), the CO(2) delivery rate was less than 0.258 mmol CO(2) L(-)(1) culture h(-)(1), and the plantlet density was at least 10 g fresh mass L(-)(1). Increasing the aeration gas CO(2) partial pressure from 0.00035 to 0.0072 atm decreased the cultivation pH from 8.8 to 7.8, prolonged the second exponential phase of growth by increasing the CO(2) delivery rate, and also increased the photosynthetic oxygen evolution rate. Impeller speeds ranging from 60 to 250 rpm, which generated average shear rates of 2-10 s(-)(1), did not have a significant effect on biomass production rate. However, microplantlets cultivated in a stirred tank bioreactor ultimately assumed compact spherical shape, presumably to minimize exposure to hydrodynamic stress.     

Modelling and design of a high productivity ethanol process using Zymomonas mobilis — I

Growth kinetics and ethanol production of Zymomonas mobilis in a bioreactor with cell recycle were modelled. High specific growth rates can be used to control excessive biomass accumulation in the system. Predicted peak productivity with a cell concentration of 80 g l⁻¹, a dilution rate of 6.5 h⁻¹, and a feed glucose concentration of 120 g l⁻¹ is 350 g l⁻¹ h⁻¹. The design of a special recycle reactor using a filter which should permit the operating conditions required for the validation of the model is proposed.     

Mixed feeds of glycerol and methanol can improve the performance of Pichia pastoris cultures: A quantitative study based on concentration gradients in transient continuous cultures

Transient continuous cultures constitute a means to speed up strain characterization, by avoiding the need for many time-consuming steady-state experiments. In this study, mixed substrate growth on glycerol and methanol of a Pichia pastoris strain expressing and secreting recombinant avidin was characterized quantitatively by performing a nutrient gradient with linear increase of the methanol fraction in the feed medium from 0.5 to 0.93 C-mol C-mol(-1) at a dilution rate of 0.06 h(-1). The influence of the methanol fraction in the feed medium on recombinant avidin productivity and on specific alcohol oxidase activity were also examined. Results showed that, compared with cultures on methanol as sole carbon source, the specific recombinant avidin production rate was the same provided the methanol fraction in the feed medium was higher than 0.6 C-mol C-mol(-1). The volumetric avidin production rate was even 1.1-fold higher with a methanol fraction in the feed medium of 0.62 C-mol C-mol(-1) as a result of the higher biomass yield on mixed substrate growth compared with methanol alone. Moreover, since heat production and oxygen uptake rates are lower during mixed substrate growth on glycerol and methanol, mixed substrate cultures present technical advantages for the performance of high cell density P. pastoris cultures. Results obtained in a high cell density fed-batch culture with a mixed feed of 0.65 C-mol C-mol(-1) methanol and 0.35 C-mol C-mol(-1) glycerol were in agreement with results obtained during the transient nutrient gradient.     

Plasmid stability and kinetics of continuous production of glucoamylase by recombinant <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> in an airlift bioreactor

Production of glucoamylase by recombinant Saccharomyces cerevisiae C468/pGAC9 (ATCC 20690) in a continuous stirred tank bioreactor was studied at different dilution rates. Plasmid stability was found to be growth (dilution rate) dependent; it increased with the dilution rate. Bioreactor productivity and specific productivity also increased with the dilution rate. A kinetic equation was used to model the plasmid stability kinetics. The growth rate ratio between plasmid-carrying and plasmid-free cells decreased from 1.397 to 1.215, and segregational instability or probability of plasmid loss from each cell division decreased from 0.059 to 0.020 as the dilution rate increased from 0.10 to 0.37 1/h. The specific growth rates increased with dilution rate, while the growth rate difference between plasmid-carrying and plasmid-free cell populations was negligible. This was attributed to the low copy number of the hybrid plasmid pGAC9. Thus, the growth rate had no significant effect on plasmid instability. The proposed kinetics was consistent with experimental results, and the model simulated the experimental data well.     

Investigation of parameters affecting a fixed bed bioreactor process for recombinant cell lines

A BHK 21 cell line expressing a recombinant antibody was grown in a fixed bed reactor (FBR) system using a porous support made of Siran glass beads. The contribution of five process variables (bead and inoculum sizes; circulation and dilution rates; glutamine concentration of the feed) to the productivity of the process (defined as production rate, effluent product concentration or yield of product on medium supplied) was investigated using a partial factorial experimental design. Individually, none of the variables tested had a significant affect upon productivity. The combination of smaller bead and inoculum sizes, higher circulation and dilution rates, plus higher feed glutamine concentration gave a markedly higher productivity than any other combination of variable levels tested. This combination of variable levels suggested that better results shold be obtained using a fluidised bed reactor system. However, comparison of the productivities of the two systems showed that the FBR gave the better results. This result can be explained in terms of the relationship of Qs_rAb to .Abbreviations C concentration - D dilution rate - FBR fixed bed bioreactor - FIBR fluidised bed bioreactor - Gln glutamine - Qs cell specific rate - Qv volumetric rate - rAb recombinant antibody - X_v viable cell density - specific growth rate     

Metabolic characterization of a L-lysine-producing strain by continuous culture

Continuous culture experiments with the L-producer, Corynebacterium glutamicum, were carried out to characterize the effect of specific growth rate on fermentation yields, specific rates, productivities, and fluxes through the primary metabolism. The specific productivity of L-lysine exhibited a maximum with respect to specific growth rate, with an initial growth-associated behavior up to specific growth rates of about 0.1 h(-1), and a constant specific productivity for specific growth rates in the range of about 0.1 to 0.2 h(-1). The productivity dropped at specific growth rates larger than about 0.2 h(-1). The yield of L-lysine on glucose increased approximately linearly with decreasing specific growth rate over the entire range studied, as did the respiratory quotient. A direct relationship was established between the culture respiratory quotient and the L-lysine yield. By explicitly accounting for glucose used for biomass synthesis, it was shown that the strain synthesizes L-lysine with an intrinsic yield, or efficiency, of about 0.41 mol L-lysine/mol glucose, compared with the theoretical yield of 0.75 mol/mol. Metabolic flux modeling based on the continuous culture data suggests that the production of ATP is not likely to be a limiting factor in L-lysine production, and that a high TCA cycle activity, coupled with a tightly controlled split of metabolite flow at the PEP node, is likely the cause of the large discrepancy between theoretical and actual yields in L-lysine fermentations.     

Inoculum production of the ectomycorrhizal fungus Pisolithus microcarpus in an airlift bioreactor

Many important tree species in reforestation programs are dependent on ectomycorrhizal symbiosis in order to survive and grow, mainly in poor soils. The exploitation of this symbiosis to increase plant productivity demands the establishment of inoculum production methods. This study aims to propose an inoculum production method of the ectomycorrhizal fungus Pisolithus microcarpus (isolate UFSC-Pt116) using liquid fermentation in an airlift bioreactor with external circulation. The fungus grew as dark dense pellets during a batch fermentation at 25.5 degrees C and air inlet of 0.26-0.43 vvm. The maximum biomass (dry weight) achieved in the airlift bioreactor was approximately 5 g.l(-1) after 10-11 days. The specific growth rate (micro(x)) in the exponential phase was 0.576 day(-1), the yield factor (Y(X/S)) 0.418, and the productivity (P(X)) 0.480 g.l(-1).day(-1). This specific growth rate was higher than that observed by other authors during fermentation processes with other Pisolithus isolates. The method seems to be very suitable for biomass production of this fungus. However, new studies on the fungus growth morphology in this system, as well as on the efficiency of the process for the cultivation of other ectomycorrhizal fungi, are necessary. It is also necessary to test the infectivity and efficiency of the inoculum towards the hosts.     

Performance characterization of a model bioreactor for the biodegradation of trichloroethylene by Pseudomonas cepacia G4

Pseudomonas cepacia G4 grown in chemostats with phenol demonstrated constant specific degradation rates for both phenol and trichloroethylene (TCE) over a range of dilution rates. Washout of cells from chemostats was evident at a dilution rate of 0.2 h-1 at 28 degrees C. Increased phenol concentrations in the nutrient feed led to increased biomass production with constant specific degradation rates for both phenol and TCE. The addition of lactate to the phenol feed led to increased biomass production but lowered specific phenol and TCE degradation rates. The maximum potential for TCE degradation was about 1.1 g per day per g of cell protein. Cell growth and degradation kinetic parameters were used in the design of a recirculating bioreactor for TCE degradation. In this reactor, the total amount of TCE degraded increased as either reaction time or biomass was increased. TCE degradation was observed up to 300 microM TCE with no significant decreases in rates. On the average, this reactor was able to degrade 0.7 g of TCE per day per g of cell protein. These results demonstrate the feasibility of TCE bioremediation through the use of bioreactors.     

Performance characterization of a model bioreactor for the biodegradation of trichloroethylene by Pseudomonas cepacia G4.

Pseudomonas cepacia G4 grown in chemostats with phenol demonstrated constant specific degradation rates for both phenol and trichloroethylene (TCE) over a range of dilution rates. Washout of cells from chemostats was evident at a dilution rate of 0.2 h-1 at 28 degrees C. Increased phenol concentrations in the nutrient feed led to increased biomass production with constant specific degradation rates for both phenol and TCE. The addition of lactate to the phenol feed led to increased biomass production but lowered specific phenol and TCE degradation rates. The maximum potential for TCE degradation was about 1.1 g per day per g of cell protein. Cell growth and degradation kinetic parameters were used in the design of a recirculating bioreactor for TCE degradation. In this reactor, the total amount of TCE degraded increased as either reaction time or biomass was increased. TCE degradation was observed up to 300 microM TCE with no significant decreases in rates. On the average, this reactor was able to degrade 0.7 g of TCE per day per g of cell protein. These results demonstrate the feasibility of TCE bioremediation through the use of bioreactors.     

Effects of post-induction feed strategies on secretory production of recombinant streptokinase in Escherichia coli

The effects of post-induction nutrient feed rates, on recombinant streptokinase production in fed-batch processes, were investigated using various feed profiles. Recombinant streptokinase was produced using a secretory expression system and was induced by a temperature up-shift, using a temperature-sensitive λ_PL promoter. The specific growth rates decreased sharply upon induction of recombinant protein expression, thus necessitating a variable feed strategy in the post-induction phase. The various feed profiles employed in the post-induction phase included constant feed rates, linearly increasing feed rate and exponentially varying feed rates. Significant differences were obtained in the specific activity of streptokinase produced in these fed-batch processes. A maximum activity per unit biomass of 4.96 × 10⁶ and 4.43 × 10⁶ IU/g DCW was achieved for exponentially decreasing feed and linearly increasing feed, respectively. The decrease in specific growth rate during the post-induction phase was also less pronounced in these cases in comparison to other fed-batch experiments. It was observed that streptokinase productivity is governed by the nutrient feed rate per unit biomass at a critical juncture after induction. The highest activity per unit biomass was obtained when the nutrient feed rate per unit biomass was around 0.7–0.8 g glucose (g DCW)⁻¹ h⁻¹, between 2 and 4 h after induction.     

Oscillatory behavior of Saccharomyces cerevisiae in continuous culture: I. Effects of pH and nitrogen levels

The appearance of sustained oscillations in bioreactor variables (biomass and nutrient concentrations) in continuous cultures of Saccharomyces cerevisiae indicates the complex nature of microbial systems, the inadequacy of current growth kinetic models, and the difficulties which may arise in bioprocess control and optimization. In this study we investigate continuous bioreactor behavior over a range of operating conditions (dilution rate, feed glucose concentration, feed ammonium concentration, dissolved oxygen, and pH) to determine the process requirements which lead to oscillatory behavior. We present new results which indicate that high feed ammonium concentrations may eliminate oscillations and that under oscillatory conditions ammonium levels are generally low and oscillatory as well. The effects of pH are complex and oscillations were only observed at pH values 5.5 and 6.5; no oscillations were observed at a pH of 4.5. Under our nominal operating conditions (feed glucose concentration 10 g/L, dilution rate 0.145 h(-1), feed ammonium concentration 0.0303M, dissolved oxygen level 50%, pH 5.5, and T = 30 degrees C) we found two possible final bioreactor states depending on the transient used to reach the nominal operating conditions. One of the states was oscillatory and characteristic of oxidative metabolism and the other was nonoscillatory and fermentative.