Quasi-Static and Dynamic Nanoindentation of Some Selected Biomaterials

This study details an investigation of the viscoelastic behavior of some biomaterials （nacre, cattle horn and beetle cuticle） at lamellar length scales using quasi-static and dynamic nanoindentation techniques in the materials＇ Transverse Direction （TD） and Longitudinal Direction （LD）. Our results show that nacre exhibits high fracture toughness moving towards a larger cam- paniForm as the stress frequency varies from 10 Hz to 200 Hz. Elytra cuticle exhibits the least fracture toughness presenting little energy dissipation in TD. It was initially speculated that the fracture toughness of the subject materials would be directly related to energy-dissipating mechanisms （mechanical hysteresis）, but not the maximum value of the loss tangent tan＆ However, it was found that the materials＇ elastic modulus and hardness are similar in both the TD and LD when assessed using the quasi-static nanoindentation method, but not dynamic nanoindentation. It is believed that the reported results can be useful in the design of new crack arrest and damping materials based on biological counterparts.     

The effect of hydration on mechanical anisotropy,topography and fibril organization of the osteonal lamellae

The effect of hydration on the mechanical properties of osteonal bone, in directions parallel and perpendicular to the bone axis, was studied on three length scales: (i) the mineralized fibril level (~100 nm), (ii) the lamellar level (~6 µm); and (iii) the osteon level (up to ~30 µm).We used a number of techniques, namely atomic force microscopy (AFM), nanoindentation and microindentation. The mechanical properties (stiffness, modulus and/or hardness) have been studied under dry and wet conditions. On all three length scales the mechanical properties under dry conditions were found to be higher by 30–50% compared to wet conditions. Also the mechanical anisotropy, represented by the ratio between the properties in directions parallel and perpendicular to the osteon axis (anisotropy ratio, designated here by AnR), surprisingly decreased somewhat upon hydration. AFM imaging of osteonal lamellae revealed a disappearance of the distinctive lamellar structure under wet conditions. Altogether, these results suggest that a change in mineralized fibril orientation takes place upon hydration.     

Experimental investigation of collagen waviness and orientation in the arterial adventitia using confocal laser scanning microscopy

Mechanical properties of the adventitia are largely determined by the organization of collagen fibers. Measurements on the waviness and orientation of collagen, particularly at the zero-stress state, are necessary to relate the structural organization of collagen to the mechanical response of the adventitia. Using the fluorescence collagen marker CNA38-OG488 and confocal laser scanning microscopy, we imaged collagen fibers in the adventitia of rabbit common carotid arteries ex vivo. The arteries were cut open along their longitudinal axes to get the zero-stress state. We used semi-manual and automatic techniques to measure parameters related to the waviness and orientation of fibers. Our results showed that the straightness parameter (defined as the ratio between the distances of endpoints of a fiber to its length) was distributed with a beta distribution (mean value 0.72, variance 0.028) and did not depend on the mean angle orientation of fibers. Local angular density distributions revealed four axially symmetric families of fibers with mean directions of 0°, 90°, 43° and ?43°, with respect to the axial direction of the artery, and corresponding circular standard deviations of 40°, 47°, 37° and 37°. The distribution of local orientations was shifted to the circumferential direction when measured in arteries at the zero-load state (intact), as compared to arteries at the zero-stress state (cut-open). Information on collagen fiber waviness and orientation, such as obtained in this study, could be used to develop structural models of the adventitia, providing better means for analyzing and understanding the mechanical properties of vascular wall.     

Lamellar bone: structure-function relations.

The term "bone" refers to a family of materials that have complex hierarchically organized structures. These structures are primarily adapted to the variety of mechanical functions that bone fulfills. Here we review the structure-mechanical relations of one bone structural type, lamellar bone. This is the most abundant type in many mammals, including humans. A lamellar unit is composed of five sublayers. Each sublayer is an array of aligned mineralized collagen fibrils. The orientations of these arrays differ in each sublayer with respect to both collagen fibril axes and crystal layers, such that a complex rotated plywood-like structure is formed. Specific functions for lamellar bone, as opposed to the other bone types, could not be identified. It is therefore proposed that the lamellar structure is multifunctional-the "concrete" of the bone family of materials. Experimentally measured mechanical properties of lamellar bone demonstrate a clear-cut anisotropy with respect to the axis direction of long bones. A comparison of the elastic and ultimate properties of parallel arrays of lamellar units formed in primary bone with cylindrically shaped osteonal structures in secondary formed bone shows that most of the intrinsic mechanical properties are built into the lamellar structure. The major advantages of osteonal bone are its fracture properties. Mathematical modeling of the elastic properties based on the lamellar structure and using a rule-of-mixtures approach can closely simulate the measured mechanical properties, providing greater insight into the structure-mechanical relations of lamellar bone.     

Gastropod nacre: structure, properties and growth--biological, chemical and physical basics

The biogenic polymer/mineral composite nacre is a non-brittle biological ceramic, which self-organizes in aqueous environment and under ambient conditions. It is therefore an important model for new sustainable materials. Its highly controlled structural organization of mineral and organic components at all scales down to the nano- and molecular scales is guided by organic molecules. These molecules then get incorporated into the material to be responsible for properties like fracture mechanics, beauty and corrosion resistance. We report here on structure, properties and growth of columnar (gastropod) nacre with emphasis on the genus Haliotis in contrast to sheet nacre of many bivalves.     

Heterogeneity of yield strain in low-density versus high-density human trabecular bone

Understanding the off-axis behavior of trabecular yield strains may lend unique insight into the etiology of fractures since yield strains provide measures of failure independent of elastic behavior. We sought to address anisotropy of trabecular yield strains while accounting for variations in both density and anatomic site and to determine the mechanisms governing this behavior. Cylindrical specimens were cored from vertebral bodies (n=22, BV/TV=0.11±0.02) and femoral necks (n=28, BV/TV=0.22±0.06) with the principal trabecular orientation either aligned along the cylinder axis (on-axis, n=22) or at an oblique angle of 15° or 45° (off-axis, n=28). Each specimen was scanned with micro-CT, mechanically compressed to failure, and analysed with nonlinear micro-CT-based finite element analysis. Yield strains depended on anatomic site (p=0.03, ANOVA), and the effect of off-axis loading was different for the two sites (p=0.04)—yield strains increased for off-axis loading of the vertebral bone (p=0.04), but were isotropic for the femoral bone (p=0.66). With sites pooled together, yield strains were positively correlated with BV/TV for on-axis loading (R²=58%, p<0.0001), but no such correlation existed for off-axis loading (p=0.79). Analysis of the modulus-BV/TV and strength-BV/TV relationships indicated that, for the femoral bone, the reduction in strength associated with off-axis loading was greater than that for modulus, while the opposite trend occurred for the vertebral bone. The micro-FE analyses indicated that these trends were due to different failure mechanisms for the two types of bone and the different loading modes. Taken together, these results provide unique insight into the failure behavior of human trabecular bone and highlight the need for a multiaxial failure criterion that accounts for anatomic site and bone volume fraction.     

Reconstruction of human maxillary defects with nacre powder: histological evidence for bone regeneration

The defective areas in the premolar-molar region of maxillary alveolar bone of eight patients were reconstructed using powdered nacre from the giant oyster Pinctada maxima. Histological, microradiographic and polarized light studies of drill biopsies taken 6 months postoperatively showed that nacre was tightly bound to newly-formed bone. The nacre was gradually and centripetally biodissolved and replaced with immature and then mature lamellar bone. These results are in agreement with our previous experimental in vitro data indicating that nacre has good osteogenic properties.     

Lamellar Bone: Structure–Function Relations

The term “bone” refers to a family of materials that have complex hierarchically organized structures. These structures are primarily adapted to the variety of mechanical functions that bone fulfills. Here we review the structure–mechanical relations of one bone structural type, lamellar bone. This is the most abundant type in many mammals, including humans. A lamellar unit is composed of five sublayers. Each sublayer is an array of aligned mineralized collagen fibrils. The orientations of these arrays differ in each sublayer with respect to both collagen fibril axes and crystal layers, such that a complex rotated plywood-like structure is formed. Specific functions for lamellar bone, as opposed to the other bone types, could not be identified. It is therefore proposed that the lamellar structure is multifunctional—the “concrete” of the bone family of materials. Experimentally measured mechanical properties of lamellar bone demonstrate a clear-cut anisotropy with respect to the axis direction of long bones. A comparison of the elastic and ultimate properties of parallel arrays of lamellar units formed in primary bone with cylindrically shaped osteonal structures in secondary formed bone shows that most of the intrinsic mechanical properties are built into the lamellar structure. The major advantages of osteonal bone are its fracture properties. Mathematical modeling of the elastic properties based on the lamellar structure and using a rule-of-mixtures approach can closely simulate the measured mechanical properties, providing greater insight into the structure–mechanical relations of lamellar bone.     

The SEM and TEM study on the laminated structure of individual aragonitic nacre tablet in freshwater bivalve H. cumingii Lea shell

Nacre (mother-of-pearl), one of the natural composite materials, is renowned for its excellent mechanical properties and becomes a model for study on the biominerals. In the present study on bivalve H. cumingii Lea, the forming nacre tablet was observed with SEM to show laminated character on the lateral growing surfaces. Correspondingly, HRTEM showed dense crystal defects on (0 0 1) plane of the aragonite nacre tablet which might be caused by the adsorption of organic macromolecules on the plane. The correlation of the laminated growth mode and crystal defects on (0 0 1) plane was discussed. These findings could enhance our understanding to the formation mechanism of the nacre tablet as well as the superior mechanical properties of the nacre.     

Structural organization and phase behavior of phospholipid fractions of actinobacteria in relation to storage conditions

X-ray diffraction analysis provided information on structural organization, phase behavior, and stability of the major parameters of phospholipid fractions of the cell membranes of actinobacteria strains Streptomyces hygroscopicus RIA 1433, Nonomuraea roseoviolacea subsp. carminata INA 4281, and Nonomuraea sp. INA 34-06 depending on the storage conditions and hydration level. Phospholipids of S. hygroscopicus were shown to form densely packed multilamellar layers. The phospholipid fraction of this microorganism was notable for homogeneity and stability of its structural organization upon storage at 4°C during 10 months. On the contrary, lipids of the phospholipid fractions of N. roseoviolacea subsp. carminata INA 4281 and Nonomuraea sp. INA 34-06 formed lamellar and inverted hexagonal (H_II) phases. The phase depended on hydration level and changed in the course of storage. We assume that the revealed differences in phase structural organization of actinobacterial phospholipid fractions may indicate long-term stability of their membrane structures.     

Studies on the interaction of cholesterol with diester- and dietherlecithin

The lamellar repeat distances of aqueous dispersions of rac-1,2-dioctadec-9′-cis-enyl-glycero-3-phosphorylcholine (dietherlecithin) and 1,2-dioctadec-9′-cis-enoyl-sn-glycero-3-phosphorylcholine (diesterlecithin) have been measured by X-ray diffraction as a function of water concentration. The point of maximum hydration was found to be 43% (w/w) and 40% (w/w) for dietherlecithin and diesterlecithin respectively; the corresponding lamellar repeat distances being 62.3 Å and 60.5 A. Incorporation of cholesterol above maximum hydration results in the initial increase in the lamellar repeat distance with a maximum around cholesterol concentrations of 25 and 33 mol % for dietherlecithin and die diesterlecithin respectively.The apparent partial specific volumes of the two lecithins and for lecithin-cholesterol mixtures in sonicated aqueous dispersions were measured. Values of 1.024 cm³ · g^?1 and 0.987 cm³ · g^?1 were obtained for diether- and diesterlecithin, respectively, at 20°C. Diesterlecithin-cholesterol mixtures showed a very small change in partial specific volume while mixtures of dietherlecithin-cholesterol showed a very marked decrease with increasing proportions of cholesterol.From these data a series of structure parameters are derived for the two lecithins and possible implications for the nature of the lecithin-cholesterol interaction are discussed.     

Determination of hydration properties and thermal behavior of Paecilomyces variotii by differential scanning calorimetry

Due to the structure and the composition of Paecilomyces variotii, the mycelia of this fungus could have potential applications as ingredients in wettable foods. For this use, drying could be employed, justifying the study of thermal behavior of P. variotii. The objectives of this work were to perform a study of thermal behavior of P. variotii isolates, to evaluate the hydration properties of these mycelia and to analyze the effect of different technological parameters on the latter properties. Wet cultures exhibited a wide endothermic transition, with mean values of peak temperature of 61°C and denaturation enthalpy of 4 J/g dry matter. Initial (50°C) and final (80°C) temperatures of the endothermic transition were used to dry the mycelia. Freeze-drying was also assayed. For all dried mycelia, a decrease in denaturation enthalpy between 40 and 50% was observed for drying at 50°C and freeze-drying, and a drastic decrease of almost 100% for drying at 80°C. According to the hydration properties, wet mycelia exhibited water holding capacity (WHC) value of 45 g water/g dry matter. Significant differences among dried mycelia, resulting WHC values in order: 50°C > freeze-dried > 80°C (p < 0.05) were revealed for each P. variotii strain. Fungi obtained by drying at 50 C and by freeze-drying, showed a rapid water absorption (t _1/2 < 0.1 min). Ionic strength, pH and particle size of dried mycelia influenced the hydration properties.     

Phase behavior of ethanolamine plasmalogen

In the present study the phase behavior of multilamellar dispersions of 1-O-(1′-alkenyl)-2-oleoyl-glycerophosphoethanolamine (ethanolamine plasmalogen), 1-O-alkyl-2-oleoyl-glycerophosphoethanolamine and 1-acyl-2-oleoyl-glycerophosphoethanolamine was compared using differential scanning calorimetry (DSC) and ³¹P-NMR. The three compounds differed only in the type of bonding (vinyl ether, alkyl ether or acyl ester) linking the aliphatic moiety to position 1 of sn-glycerol.The gel to liquid-crystalline phase transition temperature as determined by DSC was lowest for ethanolamine plasmalogen (26°C) and was similar for the alkylacyl and diacyl analogs (29.5° and 30°C, respectively). Enthalpies of the G → L phase transition were not significantly different for the three phospholipids tested.Ethanolamine plasmalogen undergoes the lamellar to hexagonal phase transition at 30°C, the analogous alkylacyl-glycerophosphoethanolamine(alkylacyl-GPE) and diacyl-GPE at 53°C and 69°C, respectively. Thus, an alkenyl ether bond in position 1 of sn-glycerol, the structural characteristic of plasmalogens, effectively stabilizes the hexagonal H_II arrangement of ethanolamine glycerophospholipids, while it has relatively little effect on destabilization of the lamellar gel state.     

The Micromechanics of Biological and Biomimetic Staggered Composites

Natural materials such as bone,tooth and nacre achieve attractive properties through the “staggered structure",which consists of stiff,parallel inclusions of large aspect ratio bonded together by a more ductile and tougher matrix.This seemingly simple structure displays sophisticated micromechanics which lead to unique combinations of stiffness,strength and toughness.In this article we modeled the staggered structure using finite elements and small Representative Volume Elements (RVEs) in order to explore microstructure-property relationships.Larger aspect ratio of inclusions results in greater stiffness and strength,and also significant amounts of energy dissipation provided the inclusions do not fracture in a brittle fashion.Interestingly the ends of the inclusions (the junctions) behave as crack-like features,generating theoretically infinite stresses in the adjacent inclusions.A fracture mechanics criterion was therefore used to predict the failure of the inclusions,w hich led to new insights into how the interfaces act as a "soft wrap" for the itclusions,completely shielding them from excessive stresses.The effect of statistics on the mechanics of the staggered structure was also assessed using larger scale RVEs.Variations in the microstructure did not change the modulus of the material,but slightly decreased the strength and significantly decreased the failure strain.This is explained by strain localization,which can in turn be delayed by incorporating vaviness to the inclusions.In addition,we show that the columnar and random arrangements,displaying different deformation mechanisms,lead to similar overall properties.The guidelines presented in this study can be used to optimize the design of staggered synthetic composites to achieve mechanical performances comparable to natural materials.     

Fracture Toughness Properties of Three Different Biomaterials Measured by Nanoindentation

The fracture toughness of hard biomaterials, such as nacre, bovine hoof wall and beetle cuticle, is associated with fibrous or lamellar structures that deflect or stop growing cracks. Their hardness and reduced modulus were measured by using a nanoindenter in this paper. Micro/nanoscale cracks were generated by nanoindentation using a Berkovich tip. Nanoindentation of nacre and bovine hoof wall resulted in pile-up around the indent. It was found that the fracture toughness （Kc） of bovine hoof wall is the maximum, the second is nacre, and the elytra cuticle of dung beetle is the least one.     

Derivation of the Stress-Strain Behavior of the constituents of Bio-Inspired Layered TiO₂/PE-Nanocomposites by Inverse Modeling Based on FE-Simulations of Nanoindentation Test

Owing to the apparent simple morphology and peculiar properties, nacre, an iridescent layer, coating of the inner part of mollusk shells, has attracted considerable attention of biologists, material scientists and engineers. The basic structural motif in nacre is the assembly of oriented plate-like aragonite crystals with a ’brick’ (CaCO₃ crystals) and ’mortar’ (macromolecular components like proteins) organization. Many scientific researchers recognize that such structures are associated with the excellent mechanical properties of nacre and biomimetic strategies have been proposed to produce new layered nanocomposites. During the past years, increasing efforts have been devoted towards exploiting nacre’s structural design principle in the synthesis of novel nanocomposites. However, the direct transfer of nacre’s architecture to an artificial inorganic material has not been achieved yet. In the present contribution we report on laminated architecture, composed of the inorganic oxide (TiO₂) and organic polyelectrolyte (PE) layers which fulfill this task.
To get a better insight and understanding concerning the mechanical behaviour of bio-inspired layered materials consisting of oxide ceramics and organic layers, the elastic-plastic properties of titanium dioxide and organic polyelectrolyte phase are determined via FE-modelling of the nanoindentation process. With the use of inverse modeling and based on numerical models which are applied on the microscopic scale, the material properties of the constituents are derived.     

On the Lamellar Structure of the Tracheid Cell Wall

Abstract: It is clear that cross sections of wood cells show a lamellar structure. This paper investigates the orientation of this lamellar structure of spruce (Picea abies) tracheids using atomic force microscopy (AFM) and scanning electron microscopy (SEM). Cross sections of spruce wood were produced through fracturing in longitudinal bending and tensile testing. When investigated with SEM, the fracture surfaces show a structure of mostly larger radial lamellae, in the order of 30 - 100 nm, i.e., agglomerations of a few cellulose aggregates. Thin transverse sections of the fracture zones investigated with atomic force microscopy show concentric lamellae with a width in the order of a single cellulose aggregate, i.e., 15 - 25 nm. No structural connection to the splinters in the radial direction can be seen. It is suggested that the radial lamellar structure is a consequence of the energy released during fracturing of the wood samples and that the undistorted wood has a concentric lamellar structure on a smaller structural level.     

Glycolipid storage material in Fabry's disease: a study by electron microscopy, freeze-fracture, and digital image analysis

The glycolipid storage material in Fabry's disease was studied by electron microscopy of thin-sectioned (TS) and freeze-fractured (FF) specimens. In the kidney all deposits were found to be located in lysosomes, arranged as lamellar stacks. Deposits in the heart consisted of intracytoplasmic concentric whirls or folded lamellar structures. High resolution TS micrographs disclosed various defects in the lamellar structure. For stabilization, such defects require additional amphiphilic, surface-active molecules. These molecules could interact with other cellular constituents. The lamellar periodicity of the deposits in FF specimens was determined by reconstruction of the three-dimensional fracture face by digital image analysis. Homogeneous multilamellar deposits exhibited a periodicity of 14-15 nm, contrasting with the conventional estimates of 4-5 nm on TS micrographs. This difference is explained by better preservation of the physiologic hydrated state in FF specimens, with 1 vol of lipids binding 2 vol of water. Inhomogeneous structures with an even higher state of hydration included water lenses between the sheets. The strong hydration obviously contributes to the enlargement of the intracellular glycolipid deposits.     

Anisotropy of the fatigue behaviour of cancellous bone

The fatigue behaviour of materials is of particular interest for the failure prediction of materials and structures exposed to cyclic loading. For trabecular bone structures only a few sets of lifetime data have been reported in the literature and structural measures are commonly not considered. The influence of load contributions which are not aligned with the main physiological axis remains unclear. Furthermore site and species dependent relationships are not well described. In this study five different groups of trabecular bone, defined in terms of orientation, species and site were exposed to cyclic compression. In total, 108 fatigue tests were analysed. The lifetimes were found to decrease drastically when off-axis loads were applied. Additionally, species and site strongly affect fatigue lifetimes. Strains at failure were also found to be a function of orientation.