Experimental validation of a microcracking-based toughening mechanism for cortical bone

It has been proposed that cortical bone derives its toughness by forming microcracks during the process of crack propagation (J. Biomech. 30 (1997) 763; J. Biomech. 33 (2000) 1169). The purpose of this study was to experimentally validate the previously proposed microcrack-based toughening mechanism in cortical bone. Crack initiation and propagation tests were conducted on cortical bone compact tension specimens obtained from the antlers of red deer. For these tests, the main fracture crack was either propagated to a predetermined crack length or was stopped immediately after initiating from the notch. The microcracks produced in both groups of specimens were counted in the same surface area of interest around and below the notch, and crack growth resistance and crack propagation velocity were analyzed. There were more microcracks in the surface area of interest in the propagation than in initiation specimens showing that the formation of microcracks continued after the initiation of a fracture crack. Crack growth resistance increased with crack extension, and crack propagation velocity vs. crack extension curves demonstrated the characteristic jump increase and decrease pattern associated with the formation of microcracks. The scanning electron micrographs of crack initiation and propagation displayed the formation of a frontal process zone and a wake, respectively. These results support the microcrack-based toughening mechanism in cortical bone. Bone toughness is, therefore, determined by its ability to form microcracks during fracture.     

Rising crack-growth-resistance behavior in cortical bone: implications for toughness measurements

Fracture mechanics studies have characterized bone's resistance to fracture in terms of critical stress intensity factor and critical strain energy release rate measured at the onset of a fracture crack. This approach, although useful, provide a limited insight into fracture behavior of bone because, unlike classical brittle materials, bone is a microcracking solid that derives its resistance to fracture during the process of crack propagation from microfracture mechanisms occurring behind the advancing crack front. To address this shortfall, a crack propagation-based approach to measure bone toughness is described here and compared with crack initiation approach. Post hoc analyses of data from previously tested bovine and antler cortical bone compact specimens demonstrates that, in contrast to crack initiation approach, the crack propagation approach successfully identifies the superior toughness properties of red deer's antler cortical bone. Propagation-based slope of crack growth resistance curve is, therefore, a more useful parameter to evaluate cortical bone fracture toughness.     

Anisotropy of age-related toughness loss in human cortical bone: a finite element study

A mechanistic understanding of the role of bone quality on fracture processes is essential for determining the underlying causes of age-related changes in the mechanical response of the human bone. In this study, a previously developed cohesive finite element model was used to investigate the effects of age-related changes and the orientation of crack growth on the toughening behavior of human cortical bone. The change in the anisotropy of toughening mechanisms with age was also studied. Finite element method (FEM) simulations showed that the initiation toughness decreased by 3% and 8%/decade for transverse and longitudinal crack growth, respectively. In contrast, fracture resistance curve slope for transverse and longitudinal crack growth decreased by 2% and 3%/decade, respectively. Initiation fracture toughness values were higher for the transverse than for the longitudinal for a given age. On the other hand, propagation fracture toughness values were higher for longitudinal than for transverse crack growth for a given age. With respect to age, the toughness ratio for crack initiation decreased by 6%/decade, but that for propagation showed almost no change (less than 1%). In light of these findings, an analytical model evaluating the crack arresting feature of cement lines, is proposed to explain the factors that determine crack penetration into osteons or its deflection by cement lines.     

Cohesive finite element modeling of age-related toughness loss in human cortical bone

Although the age-related loss of bone quality has been implicated in bone fragility, a mechanistic understanding of the relationship is necessary for developing diagnostic and treatment modalities in the elderly population at risk of fracture. In this study, a finite element based cohesive zone model is developed and applied to human cortical bone in order to capture the experimentally shown rising crack growth behavior and age-related loss of bone toughness. The cohesive model developed here is based on a traction–crack opening displacement relationship representing the fracture processes in the vicinity of a propagating crack. The traction–displacement curve, defining the cohesive model, is composed of ascending and descending branches that incorporate material softening and nonlinearity. The results obtained indicate that, in contrast to initiation toughness, the finite element simulations of crack growth in compact tension (CT) specimens successfully capture the rising R-curve (propagation toughness) behavior and the age-related loss of bone toughness. In close correspondence with the experimentally observed decrease of 14–15% per decade, the finite element simulation results show a decrease of 13% in the R-curve slope per decade. The success of the simulations is a result of the ability of cohesive models to capture and predict the parameters related to bone fracture by representing the physical processes occurring in the vicinity of a propagating crack. These results illustrate that fracture mechanisms in the process zone control bone toughness and any modification to these would cause age-related toughness loss.     

Equine cortical bone exhibits rising R-curve fracture mechanics

Previous studies of the fracture properties of cortical bone have suggested that the fracture toughness increases with crack length, which is indicative of rising R-curve behavior. Based on this indirect evidence and the similarity of bone to ceramic matrix composites, we hypothesized that bone would exhibit rising R-curve behavior in the transverse orientation and that the characteristics of the R-curves would be regionally dependent within the cortex due to variations in bone microstructure and toughening mechanisms. To test these hypotheses, we conducted R-curve experiments on specimens from equine third metacarpal bones using standard fracture mechanics testing methods. Compact type specimens from the dorsal and lateral regions in the middle of the diaphysis were oriented for crack propagation transverse to the longitudinal axis of the bone.The test results demonstrate that equine cortical bone exhibits rising R-curve behavior during transverse crack propagation as hypothesized. Statistical analyses of the crack growth initiation toughness, K0, the peak toughness, Kpeak, and the crack extension at peak toughness, deltaa, revealed significant regional differences in these characteristics. Specifically, the lateral cortex displayed higher crack growth initiation and peak toughnesses. The dorsal cortex exhibited greater crack extension at the peak of crack growth resistance. Scanning electron microscopy revealed osteon pullout on fracture surfaces from the dorsal cortex and but not in the lateral cortex. Taken together, the significant differences in R-curves and the SEM fractography indicate that the fracture mechanisms acting in equine cortical bone are regionally dependent.     

Material heterogeneity,microstructure, and microcracks demonstrate differential influence on crack initiation and propagation in cortical bone

The recent studies have shown that long-term bisphosphonate use may result in a number of mechanical alterations in the bone tissue including a reduction in compositional heterogeneity and an increase in microcrack density. There are limited number of experimental and computational studies in the literature that evaluated how these modifications affect crack initiation and propagation in cortical bone. Therefore, in this study, the entire crack growth process including initiation and propagation was simulated at the microscale by using the cohesive extended finite element method. Models with homogeneous and heterogeneous material properties (represented at the microscale capturing the variability in material property values and their distribution) as well as different microcrack density and microstructure were compared. The results showed that initiation fracture resistance was higher in models with homogeneous material properties compared to heterogeneous ones, whereas an opposite trend was observed in propagation fracture resistance. The increase in material heterogeneity level up to 10 different material property sets increased the propagation fracture resistance beyond which a decrease was observed while still remaining higher than the homogeneous material distribution. The simulation results also showed that the total osteonal area influenced crack propagation and the local osteonal area near the initial crack affected the crack initiation behavior. In addition, the initiation fracture resistance was higher in models representing bisphosphonate treated bone (low material heterogeneity, high microcrack density) compared to untreated bone models (high material heterogeneity, low microcrack density), whereas an opposite trend was observed at later stages of crack growth. In summary, the results demonstrated that tissue material heterogeneity, microstructure, and microcrack density influenced crack initiation and propagation differently. The findings also elucidate how possible modifications in material heterogeneity and microcrack density due to bisphosphonate treatment may influence the initiation and propagation fracture resistance of cortical bone.     

Effects of intracortical porosity on fracture toughness in aging human bone: a microCT-based cohesive finite element study

The extent to which increased intracortical porosity affects the fracture properties of aging and osteoporotic bone is unknown. Here, we report the development and application of a microcomputed tomography based finite element approach that allows determining the effects of intracortical porosity on bone fracture by blocking all other age-related changes in bone. Previously tested compact tension specimens from human tibiae were scanned using microcomputed tomography and converted to finite element meshes containing three-dimensional cohesive finite elements in the direction of the crack growth. Simulations were run incorporating age-related increase in intracortical porosity but keeping cohesive parameters representing other age-related effects constant. Additional simulations were performed with reduced cohesive parameters. The results showed a 6% decrease in initiation toughness and a 62% decrease in propagation toughness with a 4% increase in porosity. The reduction in toughnesses became even more pronounced when other age-related effects in addition to porosity were introduced. The initiation and propagation toughness decreased by 51% and 83%, respectively, with the combined effect of 4% increase in porosity and decrease in the cohesive properties reflecting other age-related changes in bone. These results show that intracortical porosity is a significant contributor to the fracture toughness of the cortical bone and that the combination of computational modeling with advanced imaging improves the prediction of the fracture properties of the aged and the osteoporotic cortical bone.     

Synthesis of the posterior determinant Nanos is spatially restricted by a novel cotranslational regulatory mechanism

Nanos (Nos) protein is required in the posterior of the Drosophila embryo to promote abdominal development, but must be excluded from the anterior to permit head and thorax development [1,2]. Spatial restriction of Nos is accomplished by selective translation of the 4% of nos mRNA localized to the posterior pole and translational repression of the remaining unlocalized mRNA [3-5]. Repression is mediated by a 90-nucleotide translational control element (TCE) in the nos 3' untranslated region (UTR) and the TCE-binding protein Smaug [4,6,7], but the molecular mechanism is unknown. We used sucrose density gradient sedimentation to ascertain whether unlocalized nos mRNA is excluded from polysomes and therefore repressed during translational initiation. Surprisingly, a significant percentage of nos mRNA was found to be associated with polysomes, even in mutants in which all nos mRNA is unlocalized and repressed. Using a regulated Drosophila cell-free translation system, we showed that ribosomes contained within these polysomes are capable of elongation in vitro, under conditions in which synthesis of Nos protein is repressed. Thus, synthesis of ectopic Nos protein is inhibited by a novel regulatory mechanism that does not involve a stable arrest of the translation cycle.     

Crack propagation in cortical bone is affected by the characteristics of the cement line: a parameter study using an XFEM interface damage model

Bulk properties of cortical bone have been well characterized experimentally, and potent toughening mechanisms, e.g., crack deflections, have been identified at the microscale. However, it is currently difficult to experimentally measure local damage properties and isolate their effect on the tissue fracture resistance. Instead, computer models can be used to analyze the impact of local characteristics and structures, but material parameters required in computer models are not well established. The aim of this study was therefore to identify the material parameters that are important for crack propagation in cortical bone and to elucidate what parameters need to be better defined experimentally. A comprehensive material parameter study was performed using an XFEM interface damage model in 2D to simulate crack propagation around an osteon at the microscale. The importance of 14 factors (material parameters) on four different outcome criteria (maximum force, fracture energy, crack length and crack trajectory) was evaluated using ANOVA for three different osteon orientations. The results identified factors related to the cement line to influence the crack propagation, where the interface strength was important for the ability to deflect cracks. Crack deflection was also favored by low interface stiffness. However, the cement line properties are not well determined experimentally and need to be better characterized. The matrix and osteon stiffness had no or low impact on the crack pattern. Furthermore, the results illustrated how reduced matrix toughness promoted crack penetration of the cement line. This effect is highly relevant for the understanding of the influence of aging on crack propagation and fracture resistance in cortical bone.

     

Contribution, development and morphology of microcracking in cortical bone during crack propagation

A fracture mechanics study of cortical bone is presented to investigate the contribution, development morphology of microcracking in cortical bone during crack propagation. Post-hoc analyses of microcrack orientation, crack propagation velocity and fracture surface roughness were conducted on previously tested human and bovine bone compact tension specimens. It was found that, consistent with its higher toughness, bovine bone formed significantly more longitudinal, transverse and inclined microcracks than human bone. However, in human bone more of the microcracks that formed were longitudinal than transverse or inclined, a feature that would optimise bone's toughness. Crack propagation velocity in human and bovine bone displayed the same characteristic pattern with crack extension, where an increase in velocity is followed by a consequent decrease and vice versa. On the basis of this pattern, a model or crack propagation has been proposed. It provides a detailed account of mocrocrack formation and contribution towards the propagation of a fracture crack. Analyses of fracture surfaces indicated that, consistent with its higher toughness, bovine bone displays a rougher surface than human bone but they both have the same basic fractured element, i.e. a mineralised collagen fibril.     

Measurement of leaf biomechanical properties in studies of herbivory: Opportunities,problems and procedures

Leaf biomechanical properties have the potential to act as antiherbivore defences. However, compared with studies on chemical defences, there are few studies that have demonstrated that the physical or biomechanical structure of plants can prevent or influence herbivory. This difference in focus by ecologists may relate to the dominant paradigm of plant chemical defences in ecological research and the perceived difficulties that ecologists have with the engineering principles embedded in biomechanics. The advantage of using materials engineering concepts is that each property is precisely defined and quantifiable, although the latter may be difficult in leaves because of their composite and anisotropic nature. Most herbivory studies have used simple penetrometers to measure leaf properties, often termed ‘toughness’. As defined in materials engineering, the measured properties are ‘force to fracture’ and ‘strength’, not toughness. Measurement of strength, the resistance to crack initiation, is relevant to understanding herbivory. Measurement of ‘toughness’ as defined by materials engineering is also relevant. Toughness is the resistance to crack propagation and is a measure of the energy required to fracture the leaf. This requires more sophisticated equipment than simple penetrometers because it requires a simultaneous measure of the punch displacement. In addition, purists would argue that a punch cannot be used to measure true toughness because the crack is not controlled and plastic deformation is also involved. However, it may be the only method that allows detection of fine‐scale pattern in mechanical properties across a leaf surface at a scale that is relevant to herbivory. There is very little work on the scale at which these properties vary, particularly with regard to different sized herbivores. In addition, few studies have investigated a broad range of relevant biomechanical properties in relation to herbivory. Therefore, it is not possible yet to be definitive about the relative merits of the various types of tests. A single test might show a pattern in relation to herbivore damage at a gross level. However, to really understand the functional and ecological significance of leaf texture in relation to herbivory, a more reductionist approach is needed. Only then can we move on to the larger scales of pattern that many ecologists are seeking.     

Numerical Simulation of Bone Plate with Fatigue Crack and Investigation of Attraction Hole for Retarding Crack Growth

Premature fracture of the bone plate caused by fatigue crack is the main failure mode in treating femoral shaft fracture. In order to improve the durability of the plate, this study proposed a crack attraction hole (CAH) to retard the crack propagation based on the fracture mechanics. In this paper, a numerical model of the femoral fracture internal fixation system was constructed, in which the femur was developed using a validated simplified model. First, the fatigue crack initiation location was defined at the stress concentration through static analysis. Next, with the joint simulation method of Franc3D and ABAQUS, the fatigue crack path in the bone plate was predicted. Meanwhile, the Paris parameters of Ti-6Al-4V obtained through experiments were encoded into Franc3D to calculate the crack propagation life. Finally, we considered the influence of CAH designs with different relative vertical distances (2.0, 3.0, and 4.0 mm) and diameters (1.5, 2.0, and 2.5 mm) on the crack propagation path and life of the bone plate. Additionally, the effects of all CAH configurations on the biomechanical performance of the bone plate fixation system were evaluated. The results indicated that the fatigue crack growth path in the bone plate is comparable to a straight line, and the crack growth rate significantly increases when the crack tip reaches the outer boundary of the plate. The findings suggest that the addition of CAH in the bone plate will lead to the deflection of the crack path and increase the fatigue life. Equally important, the improvement of the fatigue life was positively correlated with the diameter of CAH and negatively correlated with the relative vertical distance. In addition, the biomechanical properties of the bone plate system were slightly affected by CAH, substantiating the feasibility of this method. Finally, the comparative analysis verified that a CAH with a relative vertical distance of 3 mm and a diameter of 2 mm exhibited superior improvement in the comprehensive performance on the bone plate.     

Effect of specimen thickness on fracture toughness of bovine patellar cartilage

Fracture toughness and crack tip opening angle were measured for bovine patellar cartilage using modified single-edged notch specimens of two thicknesses. There was no difference in fracture toughness between thin (0.7 mm) versus relatively thick (2.7 mm) specimens, but the crack tip opening angle at initiation of crack propagation was larger for the thin specimens (106 deg) than for the thick specimens (70 deg). Fracture toughness of the bovine patellar cartilage (1.03 kJ/m2) was not statistically different than that reported previously for canine patellar cartilage (1.07 kJ/m2) employing the same methods. Large variation in measurements for both bovine and canine cartilage are in part attributable to variation between individual animals, and are consistent with variation in other mechanical property measurements for articular cartilage. The observed reduction in crack tip opening angle with increased specimen thickness is consistent with behavior of some engineering materials, and demonstrates that specimen thickness influences fracture behavior for bovine patellar cartilage.     

Multiple variants of the archaeal DNA rudivirus SIRV1 in a single host and a novel mechanism of genomic variation

The DNA rudivirus SIRV1 of the hyperthermophilic archaeon Sulfolobus shows exceptional properties. Viral isolates invariably contain a population of variants with different but closely related genomes. Upon propagation in a given host strain, one or more genomes dominate in the viral population. However, upon passage into a new host strain the viral population undergoes changes and other dominant variants are selected. Sequencing and analysis of the variant genomes revealed that major differences occur in gene order, gene size and gene content at localized genomic sites. A previously unknown mechanism of genomic rearrangement involving putative 12 bp archaeal introns appears to facilitate alteration of the variant genomes. Inter-genomic recombination between the different variants also occurs. The variant genomes exhibit signature tetranucleotide sequences near their putative sites for replication initiation.     

Threshold intensity factors as lower boundaries for crack propagation in ceramics

Background  

Slow crack growth can be described in a v (crack velocity) versus K_I (stress intensity factor) diagram. Slow crack growth in ceramics is attributed to corrosion assisted stress at the crack tip or at any pre-existing defect in the ceramic. The combined effect of high stresses at the crack tip and the presence of water or body fluid molecules (reducing surface energy at the crack tip) induces crack propagation, which eventually may result in fatigue. The presence of a threshold in the stress intensity factor, below which no crack propagation occurs, has been the subject of important research in the last years. The higher this threshold, the higher the reliability of the ceramic, and consequently the longer its lifetime.     

Fracture toughness and fatigue crack propagation rate of short fiber reinforced epoxy composites for analogue cortical bone

Third-generation mechanical analogue bone models and synthetic analogue cortical bone materials manufactured by Pacific Research Laboratories, Inc. (PRL) are popular tools for use in mechanical testing of various orthopedic implants and biomaterials. A major issue with these models is that the current third-generation epoxy-short fiberglass based composite used as the cortical bone substitute is prone to crack formation and failure in fatigue or repeated quasistatic loading of the model. The purpose of the present study was to compare the tensile and fracture mechanics properties of the current baseline (established PRL "third-generation" E-glass-fiber-epoxy) composite analogue for cortical bone to a new composite material formulation proposed for use as an enhanced fourth-generation cortical bone analogue material. Standard tensile, plane strain fracture toughness, and fatigue crack propagation rate tests were performed on both the third- and fourth-generation composite material formulations using standard ASTM test techniques. Injection molding techniques were used to create random fiber orientation in all test specimens. Standard dog-bone style tensile specimens were tested to obtain ultimate tensile strength and stiffness. Compact tension fracture toughness specimens were utilized to determine plane strain fracture toughness values. Reduced thickness compact tension specimens were also used to determine fatigue crack propagation rate behavior for the two material groups. Literature values for the same parameters for human cortical bone were compared to results from the third- and fourth-generation cortical analogue bone materials. Tensile properties of the fourth-generation material were closer to that of average human cortical bone than the third-generation material. Fracture toughness was significantly increased by 48% in the fourth-generation composite as compared to the third-generation analogue bone. The threshold stress intensity to propagate the crack was much higher for the fourth-generation material than for the third-generation composite. Even at the higher stress intensity threshold, the fatigue crack propagation rate was significantly decreased in the fourth-generation composite compared to the third-generation composite. These results indicate that the bone analogue models made from the fourth-generation analogue cortical bone material may exhibit better performance in fracture and longer fatigue lives than similar models made of third-generation analogue cortical bone material. Further fatigue testing of the new composite material in clinically relevant use of bone models is still required for verification of these results. Biomechanical test models using the superior fourth-generation cortical analogue material are currently in development.     

Veins improve fracture toughness of insect wings

During the lifetime of a flying insect, its wings are subjected to mechanical forces and deformations for millions of cycles. Defects in the micrometre thin membranes or veins may reduce the insect’s flight performance. How do insects prevent crack related material failure in their wings and what role does the characteristic vein pattern play? Fracture toughness is a parameter, which characterises a material’s resistance to crack propagation. Our results show that, compared to other body parts, the hind wing membrane of the migratory locust S. gregaria itself is not exceptionally tough (1.04±0.25 MPa√m). However, the cross veins increase the wing’s toughness by 50% by acting as barriers to crack propagation. Using fracture mechanics, we show that the morphological spacing of most wing veins matches the critical crack length of the material (1132 µm). This finding directly demonstrates how the biomechanical properties and the morphology of locust wings are functionally correlated in locusts, providing a mechanically ‘optimal’ solution with high toughness and low weight. The vein pattern found in insect wings thus might inspire the design of more durable and lightweight artificial ‘venous’ wings for micro-air-vehicles. Using the vein spacing as indicator, our approach might also provide a basis to estimate the wing properties of endangered or extinct insect species.     

Computer simulation of flagellar movement. VI. Simple curvature-controlled models are incompletely specified.

Computer simulation is used to examine a simple flagellar model that will initiate and propagate bending waves in the absence of viscous resistances. The model contains only an elastic bending resistance and an active sliding mechanism that generates reduced active shear moment with increasing sliding velocity. Oscillation results from a distributed control mechanism that reverses the direction of operation of the active sliding mechanism when the curvature reaches critical magnitudes in either direction. Bend propagation by curvature-controlled flagellar models therefore does not require interaction with the viscous resistance of an external fluid. An analytical examination of moment balance during bend propagation by this model yields a solution curve giving values of frequency and wavelength that satisfy the moment balance equation and give uniform bend propagation, suggesting that the model is underdetermined. At 0 viscosity, the boundary condition of 0 shear rate at the basal end of the flagellum during the development of new bends selects the particular solution that is obtained by computer simulations. Therefore, the details of the pattern of bend initiation at the basal end of a flagellum can be of major significance in determining the properties of propagated bending waves in the distal portion of a flagellum. At high values of external viscosity, the model oscillates at frequencies and wavelengths that give approximately integral numbers of waves on the flagellum. These operating points are selected because they facilitate the balance of bending moments at the ends of the model, where the external viscous moment approaches 0. These mode preferences can be overridden by forcing the model to operate at a predetermined frequency. The strong mode preferences shown by curvature-controlled flagellar models, in contrast to the weak or absent mode preferences shown by real flagella, therefore do not demonstrate the inapplicability of the moment-balance approach to real flagella. Instead, they indicate a need to specify additional properties of real flagella that are responsible for selecting particular operating points.     

The effect of moisture absorption on the fatigue crack propagation resistance of acrylic bone cement.

In vivo, bone cement is subject to cyclic loading in a fluid environment. However, little is known about the effect of moisture absorption on the fatigue crack propagation resistance of bone cement. The effect of moisture absorption at 37 degrees C on the fatigue crack propagation resistance of a common bone cement (Endurance, DePuy, Orthopaedics, Inc.) was examined. Preliminary fracture toughness tests were conducted on disk-shaped, vacuum-mixed cement specimens (compact tension type) that were cyclically pre-cracked. Plain-strain fracture toughness K(IC) (MPa square root(m)) was determined. To study the effect of moisture absorption four treatment groups, with different soaking periods in Ringer's at 37 degrees C, of Endurance cement were tested. The specimens weights prior to and following soaking showed a significant increase in mean weight for specimens soaked for 8 and 12 weeks. Linear regression analysis of log(da/dN) vs. log (deltaK) was conducted on the combined data in each fatigue test group. Soaking bone cement in Ringer's at 37 degrees C for 8 and 12 weeks lead to an improvement in fatigue crack propagation resistance, that may be related to water sorption that increases polymer chain mobility, with enhanced crack tip blunting. It may be more physiologically relevant to conduct in vitro studies of fatigue and fracture toughness of bone cements following storage in a fluid environment.     

Multiple mechanisms collaborate to repress nanos translation in the Drosophila ovary and embryo

Translational control of gene expression is essential for development in organisms that rely on maternal mRNAs. In Drosophila, translation of maternal nanos (nos) mRNA must be restricted to the posterior of the early embryo for proper patterning of the anterior-posterior axis. Spatial control of nos translation is coordinated through the localization of a small subset of nos mRNA to the posterior pole late in oogenesis, activation of this localized mRNA, and repression of the remaining unlocalized nos mRNA throughout the bulk cytoplasm. Translational repression is mediated by the interaction of a cis-acting element in the nos 3' untranslated region with two proteins, Glorund (Glo) and Smaug (Smg), that function in the oocyte and embryo, respectively. The mechanism of Glo-dependent repression is unknown. Previous work suggests that Smg represses translation initiation but this model is not easily reconciled with evidence for polysome association of repressed nos mRNA. Using an in vitro translation system, we have decoupled translational repression of nos imposed during oogenesis from repression during embryogenesis. Our results suggest that both Glo and Smg regulate translation initiation, but by different mechanisms. Furthermore, we show that, during late oogenesis, nos translation is also repressed post-initiation and provide evidence that Glo mediates this event. This post-initiation block is maintained into embryogenesis during the transition to Smg-dependent regulation. We propose that the use of multiple modes of repression ensures inactivation of nos RNA that is translated at earlier stages of oogenesis and maintenance of this inactivate state throughout late oogenesis into embryogenesis.