Sr2ZnWO6:Eu3+,Bi3+,Li+: a potential white‐emitting phosphor for near‐ultraviolet white light‐emitting diodes

A series of Sr₂ZnWO₆ phosphors co‐doped with Eu³⁺, Bi³⁺ and Li⁺ were prepared using the Pechini method. The samples were tested using X‐ray diffraction and luminescence spectroscopy. The results show that the samples can be effectively excited by near‐ultraviolet (UV) and UV light. The introduction of Bi³⁺ and Li⁺ significantly enhances the fluorescence emission of Sr₂ZnWO₆:Eu³⁺ and changes the light emitted by the phosphors from bluish‐green to white. When excited at 371 nm, Sr_2–x–zZn_1–yWO₆:xEu³⁺,yBi³⁺,zLi⁺ (x = 0.05, y = 0.05, z = 0.05, 0.1 and 0.15) samples emit high‐performance white light. Intense red–orange emission is also observed when excited by UV light. The obtained phosphor is a potential white‐emitting phosphor that could meet the needs of excitation sources with near‐UV chips. In addition, this phosphor might have promising application as a red–orange emitting phosphor for white light‐emitting diodes based on UV light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

A new rhodamine‐based fluorescent chemodosimeter for mercuric ions in water media

A new rhodamine–ethylenediamine–nitrothiourea conjugate (RT) was synthesized and its sensing property as a fluorescent chemodosimeter toward metal ions was explored in water media. Analytical results from absorption and fluorescence spectra revealed that the addition of Hg²⁺ ions to the aqueous solution of the chemodosimeter RT caused a distinct fluorescence OFF–ON response with a remarkable visual color change from colorless to pink; however, no clear spectral and color changes were observed from other metal ions including: Zn²⁺, Cu²⁺, Cd²⁺, Pb²⁺, Ag⁺, Fe²⁺, Cr³⁺, Co³⁺, Ni²⁺, Ca²⁺, Mg²⁺, K⁺ and Na⁺. The sensing results and the molecular structure suggested that a Hg²⁺‐induced a desulfurization reaction and cyclic guanylation of the thiourea moiety followed by ring‐opening of the rhodamine spirolactam in RT are responsible for a distinct fluorescence turn‐on signal, indicating that RT is a remarkably sensitive and selective chemodosimeter for Hg²⁺ ions in aqueous solution. Hg²⁺ within a concentration range from 0.1 to 25 μM can be determined using RT as a chemodosimeter and a detection limit of 0.04 μM is achieved. Copyright © 2014 John Wiley & Sons, Ltd.     

Highly selective ratiometric fluorescent Zn2+ chemosensor based on diarylethene derivative with bi‐8‐carboxamidoquinoline unit

An asymmetrical diarylethene (1O) with a bi‐8‐carboxamidoquinoline unit was synthesized. Its photochromic and fluorescence performances on stimulation with both light and metal ions showed that the diarylethene could serve as a highly selective ratiometric fluorescent chemosensor to detect Zn²⁺ ions based on internal charge transfer and chelation‐enhanced fluorescence processes. The diarylethene could selectively discriminate Zn²⁺ from Cd²⁺ in acetonitrile. Furthermore, Job's plots based on fluorescence titration and electrospray ionization mass spectrometry analysis showed 1 : 1 binding stoichiometry between 1O and Zn²⁺. The binding constant of 1O with Zn²⁺, estimated using the Benesi–Hildebrand method, and the limit of detection were 3.37 × 10⁵ M^–1 and 4.6 × 10^–8 mol/L, respectively. Additionally, the light and metal‐responsive fluorescence behavior of 1O was used successfully to construct a molecular logic circuit with four inputs and one output. Copyright © 2016 John Wiley & Sons, Ltd.     

Construction of a novel turn‐on–off fluorescence sensor used for highly selective detection of thiamine via its quenching effect on o‐phen‐Zn2+ complex

In this work, a simple and selective fluorescence sensor approach called ‘turn‐on–off’ for the determination of thiamine (TM) has been developed. As known, the o‐phenanthroline (o‐phen) has inner fluorescence, though when reacted with zinc ions to form the o‐phen–Zn²⁺ complex the fluorescence intensity was enhanced effectively, while upon addition of TM into the o‐phen–Zn²⁺ complex solution, the intensity of the system was gently quenched, which was termed the ‘turn‐on–off’ probe. Notably, the method possessed highly selective, sensitive determination for TM with a detection limit of 0.25 μmol L^?1 and the reduced fluorescence intensity was proportional to the concentration of TM in the range 0.84–80.0 μmol L^?1. Besides, the proposed mechanism was also investigated through exploring the Fourier transform infrared (FT‐IR), nuclear magnetic resonance (NMR) spectroscopy. Furthermore, this manner was successfully applied into practical samples for TM detection with satisfactory results.     

Manganese‐oxidizing bacteria mediate the degradation of 17α‐ethinylestradiol

Manganese (II) and manganese‐oxidizing bacteria were used as an efficient biological system for the degradation of the xenoestrogen 17α‐ethinylestradiol (EE2) at trace concentrations. Mn²⁺‐derived higher oxidation states of Mn (Mn³⁺, Mn⁴⁺) by Mn²⁺‐oxidizing bacteria mediate the oxidative cleavage of the polycyclic target compound EE2. The presence of manganese (II) was found to be essential for the degradation of EE2 by Leptothrix discophora, Pseudomonas putida MB1, P. putida MB6 and P. putida MB29. Mn²⁺‐dependent degradation of EE2 was found to be a slow process, which requires multi‐fold excess of Mn²⁺ and occurs in the late stationary phase of growth, implying a chemical process taking place. EE2‐derived degradation products were shown to no longer exhibit undesirable estrogenic activity.     

Luminescent properties of 4‐aminobenzo‐15‐crown‐5 after preferential binding of ferric ions in aqueous solutions

We report a combined approach that introduces the use of 4‐aminobenzo‐15‐crown‐5 (4AB15C5) for the detection of ferric(III) ions by colorimetric, ultraviolet (UV)–visible light absorption, fluorescence, and live‐cell imaging techniques along with density functional theory (DFT) calculations. We have found that 4AB15C5 is sensitive and selective for binding ferric(III) ions in aqueous solutions. DFT calculations using the polarizable continuum model have been used to explain the strong binding of the ferric ion by 4AB15C5 in aqueous solutions. The detection limit in the fluorescence quenching measurements was found to be as low as 50 μM for the ferric ion with a determined Stern–Volmer constant of 1.52 × 10⁴ M^?1. Fluorescence intensity did not change for other ions tested, Fe²⁺, Co²⁺, Mn²⁺, Mg²⁺, Zn²⁺, Ca²⁺, NH₄⁺, Na⁺, and K⁺ ions. Live‐cell fluorescence imaging was also used to check the intracellular variations in ferric ion levels. Our spectroscopic data indicated that 4AB15C5 can bind ferric ions selectively in aqueous solutions.     

Zinc(II)‐selective ratiometric fluorescent probe based on perylene bisimide derivative

A fluorescent probe of N,N′‐biscyclohexyl‐1,7‐di(3‐pyridoxy)‐perylene‐3,4:9,10‐tetracarboxylic acid diimide has been synthesized, and exhibited excellent selectivity and sensitivity for Zn²⁺ over other competing biological cations. The Zn²⁺‐selective fluorescence blue‐shift and enhancing property in conjunction with a visible colorimetric change from orange to green could be observed. With favorable photophysical properties in the visible region, the perylene bisimide derivatives remarkably improved the performance of the probe. Copyright © 2010 John Wiley & Sons, Ltd.     

A highly selective fluorescent chemosensor for Cu2+: synthesis and properties of a rhodamine B‐containing diarylethene

A diarylethene bearing a triazole‐linked rhodamine B unit was synthesized. Its fluorescent emission was significantly enhanced in the presence of protons or Cu²⁺ due to transformation from the pirocyclic form to open‐ring form. The fluorescence was quenched sequentially upon irradiation with 297 nm light based on the intramolecular fluorescence resonance energy transfer mechanism. In an acetonitrile: water binary solvent (1: 1 v /v), the compound showed significant fluorescent enhancement for Cu²⁺ compared with a wide range of tested metal ions with a fast response and a limit of detection of 2.86 × 10^?8 mol L^?1. Using Cu²⁺ and UV light as the chemical inputs, and fluorescence intensity at 597 nm as the output, a logic gate was developed at the molecular level. Moreover, the compound can be used with a high accuracy to detect Cu²⁺ in a natural water sample.     

The special optical properties and application of the heterocyclic compound diethyl 6‐anilino‐5H‐2,3‐dithia‐5,7‐diazacyclopenta(cd)indene‐1,4‐dicarboxylate

The heterocyclic compound diethyl 6‐anilino‐5H‐2,3‐dithia‐5,7‐diazacyclopenta(cd)indene‐1,4‐dicarboxylate (D1) was found to form highly emissive aggregates in polar solvents, and the aggregate emission can be tuned by the simple addition of water to a dimethylsulfoxide solution. A theoretical study based on Density functional theory (DFT) calculations, shows that intermolecular interactions of D1 with solvent may be potential factors in the fluorescence change. In addition, the phenyl ring in D1 plays an important role because of its response to solvent. In the non‐aggregated state, deprotonation of the N–H of D1 can proceed easily on the addition of base, and the deprotonated compound might interact with Ag⁺, resulting in a significant change in color and fluorescence quenching, which make it a potential chemosensor for the selective detection of trace amounts of Ag⁺. Copyright © 2013 John Wiley & Sons, Ltd.     

A highly efficient and selective turn‐on fluorescent sensor for Hg2+, Ag+ and Ag nanoparticles based on a coumarin dithioate derivative

Based on chelation‐enhanced fluorescence, a new fluorescent coumarin derivative probe 3(1‐(7‐hydroxy‐4‐methylcoumarin)ethylidene)hydrazinecarbodithioate for Hg²⁺, Ag⁺ and Ag nanoparticles is reported. Fluorescent probe acts as a rapid and highly selective “off–on” fluorescent probe and fluorescence enhancement by factors 5 to12 times was observed upon selective complexation with Hg²⁺, Ag⁺ and Ag nanoparticles. The molar ratio plots indicated the formation of 1:1 complexes between Hg²⁺ and Ag⁺ with the probe. The linear response range covers a concentration range 0.1 × 10^–5–1.9 × 10^–5 mol/L, 0.1 × 10^–5–2.3 × 10^–5 mol/L and 0.146 × 10^–12–2.63 × 10^–12 mol/L for Hg²⁺, Ag⁺ and Ag nanoparticles, respectively. The interference effect of some anions and cations was also tested. Copyright © 2013 John Wiley & Sons, Ltd.     

Characterization of a highly Al3+‐selective fluorescence probe based on naphthalimide‐Schiff base and its application to practical water samples

A new fluorescent Al³⁺‐probe, N‐allyl‐4‐[3,3′‐((2‐aminoethyl)azanediyl)‐bis(N´‐(2‐hydroxybenzylidene)propanehy‐drazide)]‐1,8‐naphthalimide ( L ), was designed and synthesized based on 1,8‐naphthalimide. The probe L contains 1,8‐naphthalimide moiety as the fluorophore and a Schiff base as the recognition group. The structure of L was determined by single crystal X‐ray. L emission at 526 nm increased on addition of Al³⁺ under excitation wavelength at 350 nm. L exhibited high selectivity and sensitivity fluorescence emission towards to Al³⁺ in ethanol/Tris–HCl buffer solution (1:1, v/v, pH = 7.2) as compared with other tested metal ions. A good linearity with a correlation coefficient (R²) of 0.99 was observed in the concentration range 2–10 μM. The binding constant and the detection limit of L for Al³⁺ were calculated to 2.6 × 10⁴ M^?1 and 0.34 μM, respectively. The results of experiments that including Job plot, ultraviolet–visible (UV–Vis) light titration, fluorescence titration, ESI‐MS and ¹H NMR titration, indicated a 1:1 stoichiometric complex between L and Al³⁺. L was highly effective in monitoring Al³⁺ in real‐life Yellow River and tap water samples.     

A highly sensitive and reversible chemosensor for Hg2+ detection based on porphyrin‐thymine conjugates

In this study, we demonstrated a highly sensitive, selective, and reversible chemosensor for Hg²⁺ determination. This chemosensor was synthesized by direct condensation of thymin‐1‐ylacetic acid with zinc tetraaminoporphyrin, which has a porphyrin core as the fluorophore and four thymine (T) moieties as the specific interaction sites for Hg²⁺. The probe (4T‐ZnP) exhibited split Soret bands with a small peak at 408 nm and a strong band at 429 nm in a dimethylformamide/H₂O (7/3, v/v) mixed solvent as well as a strong emission band at 614 nm. Upon the addition of Hg²⁺, the probe displayed strong fluorescence quenching due to the formation of T‐Hg²⁺‐T complexes. With the aid of the fluorescence spectrometer, the chemosensor in the dimethylformamide/H₂O (7/3, v/v) mixed solvent (0.3 μM) exhibited a detection limit of 6.7 nM. Interferences from other common cations, such as Co²⁺, K⁺, Sn²⁺, Zn²⁺, Cu²⁺, Ni²⁺, Mn²⁺, Na⁺, Ca²⁺, Mg²⁺, Pb²⁺, and Cd²⁺, associated with Hg²⁺ analysis were effectively inhibited. Copyright © 2015 John Wiley & Sons, Ltd.     

A triazole‐based fluorescence probe for detecting Hg2+ ions and its biological application

A new compound, ethyl 5‐phenyl‐2‐(p‐tolyl)‐2H‐1,2,3‐triazole‐4‐carboxylate was successfully introduced and synthesized as a novel rhodamine B derivative named REPPC, and characterized by ¹H nuclear magnetic resonance (NMR), ¹³C NMR, and high resolution mass spectrometry (HRMS). It showed an obvious fluorescence and UV–visible light absorption enhancement towards Hg²⁺ ion without interference from common metal ions in N,N‐dimethylformamide–H₂O (pH 7.4). The spirolactam ring moiety of rhodamine in REPPC was converted to the open‐ring form generating a 1:1 complex with the intervention of a mercury ion, verified by electrospray ionization‐mass spectroscopy testing and density functional theory calculation. REPPC was used to visualize the level of mercury ions in living HeLa cells with encouraging results.     

A N‐(2‐hydroxyethyl)piperazine dangled 2,5‐diphenyl‐1,3,4‐oxadiazole‐based fluorescent sensor for selective relay recognition of Cu2+ and sulfide in water

A new 2,5‐diphenyl‐1,3,4‐oxadiazole‐based derivative (L) was synthesized and applied as a highly selective and sensitive fluorescent sensor for relay recognition of Cu²⁺ and S^2? in water (Tris–HCl 10 mM, pH = 7.0) solution. L exhibits an excellent selectivity to Cu²⁺ over other examined metal ions with a prominent fluorescence ‘turn‐off’ at 392 nm. L interacts with Cu²⁺ through a 1:2 binding stoichiometry with a detection limit of 4.8 × 10^–7 M. The on‐site formed L–2Cu²⁺ complex exhibits excellent selectivity to S^2? with a fluorescence ‘off–on’ response via a Cu²⁺ displacement approach. Copyright © 2016 John Wiley & Sons, Ltd.     

Redox‐triggered chiroptical switching activity of ruthenium(III)‐bis‐(β‐diketonato) complexes bearing a bipyridine‐helicene ligand

The charged, electroactive bipyridine‐helicene‐ruthenium(III) complex [ 4 ] ^{. +},PF₆^? has been prepared from 3‐(2‐pyridyl)‐4‐aza[6]helicene and a Ru‐bis‐(β‐diketonato)‐bis‐acetonitrile precursor (β‐diketonato: 2,2,6,6‐tetramethyl‐3,5‐heptanedionato). Its chiroptical properties (electronic circular dichroism and optical rotation) were studied both experimentally and theoretically and suggest the presence of 2 diastereoisomers, namely (P,Δ)‐ and (P,Λ)‐[ 4 ] ^{. +},PF₆^? (denoted jointly as (P,Δ*)‐[ 4 ] ^{. +},PF₆^?) and their mirror‐images (M,Λ)‐ and (M,Δ)‐[ 4 ] ^{. +},PF₆^? ((M,Δ*)‐[ 4 ] ^{. +},PF₆^?). The electrochemical reduction of (P,Δ*)‐[ 4 ] ^{. +},PF₆^? to neutral complex (P,Δ*)‐ 4 was performed and revealed strong changes in the UV‐vis and electronic circular dichroism spectra. A reversible redox‐triggered chiroptical switching process was then achieved.     

Tunable white light emission from single‐phased Li2SrSiO4:Dy3+ phosphors by co‐doping with Eu3+

A series of single‐phase full‐color emitting Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors were synthesized by solid‐state reaction and characterized by X‐ray diffraction and photoluminescence analyses. The samples showed emission peaks at 488 nm (blue), 572 nm (yellow), 592 nm (orange) and 617 nm (red) under 393 nm excitation. The photoluminescence excitation spectra, comprising the Eu–O charge transfer band and 4f–4f transition bands of Dy³⁺ and Eu³⁺, range from 200 to 500 nm. The Commission Internationale de I'Eclairage chromaticity coordinates for Li₂Sr_0.98−xSiO₄:0.02Dy³⁺,xEu³⁺ phosphors were simulated. By manipulating Eu³⁺ and Dy³⁺ concentrations, the color points of Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ were tuned from the greenish‐white region to white light and eventually to reddish‐white region, demonstrating that a tunable white light can be obtained by Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors. Li₂Sr_0.98−xSiO₄:0.02Dy³⁺, xEu³⁺ can serve as a white‐light‐emitting phosphor for phosphor‐converted light‐emitting diode. Copyright © 2014 John Wiley & Sons, Ltd.     

Photoluminescence properties of a new orange–red‐emitting Sm3+–La3SbO7 phosphor

The antimonate compound La₃SbO₇ has high chemical stability, lattice stiffness and thermal stability. Orange–red‐emitting antimonate‐based phosphors La₃SbO₇:xSm³⁺ (x = 0.02, 0.05, 0.08, 0.10, 0.15, 0.20 and 0.25) were synthesized. The phase structure and photoluminescence properties of these phosphors were investigated. The emission spectrum obtained on excitation at 407 nm contained exclusively the characteristic emissions of Sm³⁺ at 568, 608, 654 and 716 nm, which correspond to the transitions from ⁴G_5/2 to ⁶H_5/2, ⁶H_7/2, ⁶H_9/2 and ⁶H_11/2 of Sm³⁺, respectively. The strongest emission was located at 608 nm due to the ⁴G_5/2→⁶H_7/2 transition of Sm³⁺, generating bright orange–red light. The critical quenching concentration of Sm³⁺ in La₃SbO₇:Sm³⁺ phosphor was determined as 10% and the energy transfer between Sm³⁺ was found to be through an exchange interaction. The International Commission on Illumination chromaticity coordinates of the La₃SbO₇:0.10Sm³⁺ phosphors are located in the orange–red region. The La₃SbO₇:Sm³⁺ phosphors may be potentially used as red phosphors for white light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Properties,theoretical study and crystal structure of 3‐benzothiazole‐9‐ethyl carbazole

The title compound of 3‐benzothiazole‐9‐ethyl carbazole was synthesized by the reaction of 3‐aldehyde‐9‐ethyl carbazole and 2‐aminothiophenol. The compound was characterized by ¹H nuclear magnetic resonance (NMR) and mass spectrometry (MS). Its crystal structure was obtained and determined by single crystal X‐ray diffraction. The results showed that the crystal belongs to the orthorhombic crystal system and the cell parameters of space group P2(1)2(1)2(1) were a = 5.6626 (12) Å, b = 12.606 (3) Å, c = 22.639 (5) Å, α = 90°, β = 90°, γ = 90°, V = 1616.0 (6) ų, Z = 4, Dc = 1.350 mg/m³. The UV–vis and fluorescence spectra were also studied preliminarily. The fluorescence spectra of the title compound with bovine serum albumin (BSA) showed that BSA could be marked with the compound and the stability constant between them was 0.82 × 10⁷ M^?1. Meanwhile, the crystal and molecule were theoretically surveyed by density functional tight‐binding (DFTB). The results showed that there was an orbital overlap for lowest unoccupied molecular orbital (LUMO) between the neighbouring molecules for the crystal, which is different from the molecule structure. It was also showed that the crystal structure is a non‐conductor. Copyright © 2016 John Wiley & Sons, Ltd.     

Interaction of β‐cyclodextrin‐capped CdSe quantum dots with inorganic anions and cations

A facile method was developed for the preparation of water soluble β‐Cyclodextrin (β‐CD)‐modified CdSe quantum dots (QDs) (β‐CD‐QDs) by directly replacing the oleic acid ligands on the QDs surface with β‐CD in an alkaline aqueous solution. The as‐prepared QDs show good stability in aqueous solution for several months. Oxoanions, including phosphoric acid ion, sulphite acid ion and carbonic acid ion, affect the fluorescence of β‐CD‐QDs. Among them, H₂PO₄^– exhibited the largest quenching effect. For the polyprotic acids (HO)₃AO, the effect of acidic anions on the fluorescence of β‐CD‐QDs was in the order: monoanion (HO)₂AO₂^– > dianion (HO)AO₃^2– >> trianion AO₄^3–. After photoactivation for several days in the presence of anions at alkaline pH, the β‐CD‐QDs exhibited strong fluorescence emission. The effect of various heavy and transition metal ions on the fluorescence properties of the β‐CD‐QDs was investigated further. It was found that Ag⁺, Hg²⁺ and Co²⁺ have significant quenching effect on the fluorescence of the β‐CD‐QDs. The Stern–Volmer quenching constants increased in the order: Hg²⁺ < Co²⁺ <Ag⁺. The adsorption model of metal ions on β‐CD‐QDs was explored. Copyright © 2011 John Wiley & Sons, Ltd.     

Phenothiazine–rhodamine‐based colorimetric and fluorogenic ‘turn‐on' sensor for Zn2+ and bioimaging studies in live cells

A phenothiazine–rhodamine (PTRH) fluorescent dyad was synthesized and its ability to selectively sense Zn²⁺ ions in solution and in in vitro cell lines was tested using various techniques. When compared with other competing metal ions, the PTRH probe showed the high selectivity for Zn²⁺ ions that was supported by electronic and emission spectral analyses. The emission band at 528 nm for the PTRH probe indicated the ring closed form of PTRH, as for Zn²⁺ ion binding to PTRH, the λ_em get shift to 608 nm was accompanied by a pale yellow to pink colour (under visible light) and green to pinkish red fluorescence emission (under UV light) due to ring opening of the spirolactam moiety in the PTRH ligand. Spectral overlap of the donor emission band and the absorption band of the ring opened form of the acceptor moiety contributed towards the fluorescence resonance energy transfer ON mechanism for Zn²⁺ ion detection. The PTRH sensor had the lowest detection limit for Zn²⁺, found to be 2.89 × 10^?8 M. The sensor also demonstrated good sensing application with minimum toxicity for in vitro analyses using HeLa cells.