担载神经生长因子(NGF)的乳液法涂层纤维体外缓释研究

目的:目前周围神经修复中,神经导管是研究热点,本文研究乳液法涂层纤维制备的神经导管在神经修复中应用的可能性。方法:本文采用乳液法制备担载NGF的丝素-聚乳酸(PLLA)涂层电纺纤维,观察纤维的形态,测定NGF的体外释放动力学参数,并考察纤维释放液对于PC12细胞增殖的影响。结果:担载NGF的涂层纤维具备类似于细胞外基质(ECM)的三维结构和多孔形态;涂层纤维中NGF体外有效缓释10天;细胞实验中,在含有释放液的培养基中生长的PC12细胞,与空白对照组相比,荧光强度平均多了2000-4000个荧光强度,所以释放液可以更好地促进PC12细胞的增殖。结论:担载NGF的乳液法涂层纺丝纤维具备促进缺损周围神经修复的条件,可以进一步研究在动物体内修复缺损周围神经中的效果,为以后的临床应用打下基础。     

乳液法神经生长因子（NGF）电纺纤维的体外研究

目的：使用乳液法制备含有神经生长因子（NGF）的电纺纤维,研究其外观形貌和机械强度等物理性能,以及制备过程中NGF活性的变化,纤维中NGF的担载量和纤维体外释放动力学,评价其能否成为理想的神经修复材料,为进一步将NGF电纺纤维应用于周围神经修复奠定基础。方法：将NGF水溶液分散于PLLA溶液,通过W／O乳液法制备静电纺丝缓释纤维,对纤维的外观形貌等物理性能等进行表征,使用Elisa方法测定制备过程中NGF活性的保持以及体外释放动力学。结果：NGF电纺纤维具备类似细胞外基质（ECM）的良好外观形貌和一定的机械强度,其中NGF活性保持19．58％士6．05％,体外有效释放11天。结论：本文制备的乳液法NGF电纺纤维具备良好的物理性能,能够持续缓释有效剂量的NGF,适合作为神经修复材料进行进一步研究。     

静电纺丝制备担载神经生长因子的聚乳酸纤维的工艺研究

目的:研究担载神经生长因子(NGF)的聚乳酸纤维乳液法静电纺丝的制备工艺,从电压、溶液浓度等工艺条件进行探索,通过扫描电镜对纤维的形态结构进行观察,旨在找到最佳纺丝制备条件,并观察该条件下纤维的体外释放行为和细胞活性。方法:将NGF水溶液分散于聚乳酸(PLLA)溶液中,通过W/O乳液法制备静电纺丝纤维。分别从电压8 k V、10 k V、12 k V,浓度梯度90mg/m L、100 mg/m L、110 mg/m L进行静电纺丝纤维的制备,对纤维的形态等进行表征。使用ELISA对NGF体外释放动力学进行检测,用Alamer Blue试剂考察纤维释放液对于PC12悬浮细胞增殖的影响。结果:浓度和电压对电纺纤维制备影响很大。当浓度过大时,易堵塞纺丝喷头且纤维弯曲,过小时纤维粗细差异较大。电压过大或过小时纤维弯曲情况严重,甚至出现缠绕现象。当浓度为100 mg/m L,电压为10 k V时制备的乳液法静电纺丝聚乳酸纤维直径粗细均匀,具有较好形态。在该条件下的制备的纤维NGF体外有效释放13天,释放液可以促进PC12细胞的增殖。结论:担载NGF的聚乳酸纤维乳液法最佳静电纺丝制备条件为:PLLA溶液浓度100 mg/m L、电压10 k V,该条件下制备的担载NGF的聚乳酸纤维体外释放可累计释放13天,其释放液可有效促进PC12细胞的增殖,为进一步研究担载NGF的聚乳酸纤维导管奠定了一定的工艺基础。     

担载血管生长因子的乳液法纤维用于血管再生的研究

目的:制备担载血管生长因子(VEGF)的乳液法静电纺丝纤维膜,对其开展一系列表征,从而研究其血管再生的潜能。方法:通过W/O乳液法制备担载VEGF的静电纺丝纤维膜,并对其形态、力学性质进行表征。用VEGF ELISA分析方法对其体外释放动力学进行研究。运用CCK-8法检测乳液法静电纺丝纤维膜中VEGF的活性变化。结果:乳液法静电纺丝纤维膜呈现连通的三维网状结构,平均直径为1μm,模拟了细胞外基质(ECM),最大拉伸应力为3.03±0.66 M Pa,具有良好的抗拉伸能力,能够支持细胞的生长。乳液法纤维膜中VEGF在体外累积释放了14天,总释放量超过20000 pg,达到血管再生的有效浓度。CCK-8结果显示,乳液法纤维膜中的VEGF仍然保持较高的蛋白活性。结论:担载VEGF的乳液法静电纺丝纤维膜能够缓释出活性的蛋白,具有血管再生的潜能。     

血管内皮生长因子(VEGF)乳液法电纺纤维膜的体外研究

目的:研究担载血管内皮生长因子(VEGF)的乳液法电纺纤维膜的亲水性能、外观形态和机械性能,纤维膜中VEGF的包封率和体外释放动力学,为评价其能否应用于血管再生领域的研究奠定基础。方法:将VEGF水溶液通过W/O乳液法制备成缓释VEGF的生物可降解的丙交酯-乙交酯共聚物(PLGA)静电纺丝纤维膜,对该纤维膜的接触角、外观形态、机械性能进行表征,Elisa法测定该纤维膜的体外14天的释放行为,分别观察纤维膜释放0天、7天、14天后的电镜图。结果:加入VEGF后,纤维膜的接触角由140.0°减小到136.1°,亲水性增强,具有类似细胞外基质(ECMs)网状结构和良好的力学性能,纤维膜第1天的突释不超过载药量的50%,电镜图下显示纤维膜释放1周时纤维发生断裂。结论:通过乳液法制备的担载VEGF的电纺纤维膜具有良好的物理性能,能够持续缓释VEGF,可作为血管再生的组织工程支架进行深入研究。     

静电纺丝纳米纤维体外释放与蛋白活性的研究

目的:通过选择不同的模型蛋白,探讨准确的研究静电纺丝纳米纤维支架的体外释放和快速的测定蛋白活性的方法.方法:通过O/W乳液法静电纺丝制备纳米纤维,并用扫描电镜对纳米纤维表面进行了表征.以GM-CSF为模型蛋白,采用ELISA双抗体夹心法考察纤维的体外释放行为;以BSA为模型蛋白,用SEC-H-PLC比较纤维制备前后蛋白的聚集情况;以β-半乳糖苷酶为模型蛋白,用ONPG法比较纤维制备前后酶的催化活性.结果:纤维表面平滑,直径均一,呈现互相连通的三维网状结构.纤维在5天内释放90％以上;纤维中回收的BSA单体比例为66.53％;β-半乳糖苷酶在纤维中的催化活性保持原活性的3.37％.结论:通过选择不同的模型蛋白,能够准确的测定静电纺丝纤维的体外释放,快速的考察纤维中的蛋白活性,对于更好的研究蛋白药物纳米纤维支架具有重要的参考价值.     

乳液法静电纺丝PLGA 组织工程缓释纤维的研究

目的:研究Dextran对蛋白药物的释放影响。方法:将模型蛋白BSA溶解于多糖溶液中,通过W/O乳液法静电纺丝制备缓释纤维。采用MicroBCA法测定该纤维体外释放行为,采用SEC-HPLC检测制备前后蛋白的聚集程度,并与不含多糖的BSA纤维做对照。结果:添加Dextran以后蛋白的包封率由52.68%提高到63.92%,第一天突释不大于药物载量的15%,对蛋白单体的保持达到85%以上。结论:Dextran可以改善一般组织工程纤维中蛋白药物的释放,提高蛋白药物在制剂、贮存、释放过程中的稳定性,增加纤维的载药量。     

担载b-FGF的PLGA微球复合明胶支架的体外释放研究

目的:研究担载碱性成纤维细胞生长因子(b-FGF)微球复合明胶支架的外形特征、孔径、孔隙率及体外释放动力学,以期构建具有缓释功能、高孔隙率的担载细胞因子的新型复合明胶支架。方法:本文利用冷冻相分离法和S/O/W法先将b-FGF水溶液包裹于PLGA微球中,然后埋置于明胶溶液中制备为多孔复合明胶支架。分别对微球的形态和复合明胶支架的基本形态、孔径、孔隙率进行表征,通过Elisa法测定b-FGF在复合明胶支架中的体外释放行为。结果:制备成形态良好的三维复合明胶支架,其孔隙率为82.90%±1.45%,孔径范围为150~300μm,复合明胶支架中b-FGF在体外缓慢释放20余天。结论:担载蛋白微球复合明胶支架不仅满足组织工程支架的要求,还能有效缓释细胞因子,为细胞和组织生长提供良好的微环境,为进一步应用于组织工程领域提供了可能。     

乳液法静电纺丝PLGA组织工程缓释纤维的研究

目的：研究Dextran对蛋白药物的释放影响。方法：将模型蛋白BSA溶解于多糖溶液中,通过W/O乳液法静电纺丝制备缓释纤维。采用MicroBCA法测定该纤维体外释放行为,采用SEC-HPLC检测制备前后蛋白的聚集程度,并与不含多糖的BSA纤维做对照。结果：添加Dextran以后蛋白的包封率由52.68%提高到63.92%,第一天突释不大于药物载量的15%,对蛋白单体的保持达到85%以上。结论：Dextran可以改善一般组织工程纤维中蛋白药物的释放,提高蛋白药物在制剂、贮存、释放过程中的稳定性,增加纤维的载药量。     

一种具有空腔结构的高分子超细纤维的制备及应用研究

目的:制备一种具有空腔结构的高分子超细纤维并研究其相关性质,探索其应用。方法:结合静电纺丝技术和微流控技术,制备出具有空腔结构的聚乳酸(PLA)超细纤维,并使用荧光显微镜、扫描电子显微镜、透射电子显微镜等手段进行结构表征;采用甘油铜分光光度法、Alamar-Blue法间接检测了纤维膜的甘油含量和细胞毒性,并考察了其吸水率相较于普通实心纤维膜的变化;将PEI-质粒复合物载入纤维的空腔结构中,通过细胞转染实验验证了此纤维膜在运载质粒方面的应用。结果:纤维平均直径在1μm左右,内部均匀分布着椭圆形空腔。该纤维膜中甘油占比38.99%,吸水率为普通实心PLA纤维膜的近2倍。纤维膜与内皮细胞5天的共培养中,没有明显的细胞毒性。细胞转染检测结果证明了纤维空腔部分能有效运载质粒复合物并保证其生物活性。结论:静电纺丝技术和微流控技术有效结合,成功制备出具有空腔结构的新型高分子超细纤维,展现出了区别于普通纤维的独特性质和应用。     

Complementary Effects of Two Growth Factors in Multifunctionalized Silk Nanofibers for Nerve Reconstruction

With the aim of forming bioactive guides for peripheral nerve regeneration, silk fibroin was electrospun to obtain aligned nanofibers. These fibers were functionalized by incorporating Nerve Growth Factor (NGF) and Ciliary NeuroTrophic Factor (CNTF) during electrospinning. PC12 cells grown on the fibers confirmed the bioavailability and bioactivity of the NGF, which was not significantly released from the fibers. Primary neurons from rat dorsal root ganglia (DRGs) were grown on the nanofibers and anchored to the fibers and grew in a directional fashion based on the fiber orientation, and as confirmed by growth cone morphology. These biofunctionalized nanofibers led to a 3-fold increase in neurite length at their contact, which was likely due to the NGF. Glial cell growth, alignment and migration were stimulated by the CNTF in the functionalized nanofibers. Organotypic culture of rat fetal DRGs confirmed the complementary effect of both growth factors in multifunctionalized nanofibers, which allowed glial cell migration, alignment and parallel axonal growth in structures resembling the ‘bands of Bungner’ found in situ. Graftable multi-channel conduits based on biofunctionalized aligned silk nanofibers were developed as an organized 3D scaffold. Our bioactive silk tubes thus represent new options for a biological and biocompatible nerve guidance conduit.     

[PEAD:肝素:NGF]生物材料促进大鼠坐骨神经损伤恢复

目的:探讨新型材料poly(ethylene argininylaspartate diglyceride)(PEAD)结合肝素包裹神经生长因子组成的三元复合体比单纯运用NGF治疗大鼠坐骨神经损伤效果明显,为临床治疗外周神经损伤提供实验依据。方法:24只200g左右Wistar大鼠,分成生理盐水组,NGF组,NGF凝聚体三组,每组各8只,距梨状肌下缘远侧约1.5cm处运用静脉夹夹紧坐骨神经2min,采用无创细线(5/0)缝合肌肉和皮肤,并用碘伏进行消毒,NGF组每天沿坐骨切迹肌注80ngNGF,持续30天;NGF凝聚体组仅在造模时肌注复合体(内含2.4μg的NGF);生理盐水组给予等体积的生理盐水。术后每周运用脚步印迹法评价动物的行为学,并于30天后灌流、收集各组损伤侧坐骨神经,运用HE染色及投射电镜观察坐骨神经结构恢复情况,免疫荧光标记MBP,观察其蛋白的表达。结果:NGF组,NGF凝聚体组在行为学、病理结构及蛋白的表达远高于生理盐水组,并且NGF凝聚组的治疗效果优于NGF组。结论:新型凝聚体包载NGF具有明显的促进周围神经损伤后的修复与再生作用,能够在一定程度上提高单纯运用NGF治疗大鼠坐骨神经损伤的不足,达到更加理想和显著的促恢复效果。     

Mechanisms and control of silk-based electrospinning

Silk fibroin (SF) nanofibers, formed through electrospinning, have attractive utility in regenerative medicine due to the biocompatibility, mechanical properties, and tailorable degradability. The mechanism of SF electrospun nanofiber formation was studied to gain new insight into the formation and control of nanofibers. SF electrospinning solutions with different nanostructures (nanospheres or nanofilaments) were prepared by controlling the drying process during the preparation of regenerated SF films. Compared to SF nanospheres in solution, SF nanofilaments had better spinnability with lower viscosity when the concentration of silk protein was below 10%, indicating a critical role for SF morphology, and in particular, nanostructures, for the formation of electrospun fibers. More interesting, the diameter of electrospun fibers gradually increased from 50 to 300 nm as the concentration of SF nanofilaments in the solution increased from 6 to 12%, implying size control by simply adjusting SF nanostructure and concentration. Aside from process parameters investigated in previous studies, such as SF concentration, viscosity, and electrical potential, the present mechanism emphasizes significant influence of SF nanostructure on spinnability and diameter control of SF electrospun fibers, providing a controllable option for the preparation of silk-based electrospun scaffolds for biomaterials, drug delivery, and tissue engineering needs.     

Fabrication,Characterization and Cellular Compatibility of Poly(Hydroxy Alkanoate) Composite Nanofibrous Scaffolds for Nerve Tissue Engineering

Tissue engineering techniques using a combination of polymeric scaffolds and cells represent a promising approach for nerve regeneration. We fabricated electrospun scaffolds by blending of Poly (3-hydroxybutyrate) (PHB) and Poly (3-hydroxy butyrate-co-3- hydroxyvalerate) (PHBV) in different compositions in order to investigate their potential for the regeneration of the myelinic membrane. The thermal properties of the nanofibrous blends was analyzed by differential scanning calorimetry (DSC), which indicated that the melting and glass temperatures, and crystallization degree of the blends decreased as the PHBV weight ratio increased. Raman spectroscopy also revealed that the full width at half height of the band centered at 1725 cm⁻¹ can be used to estimate the crystalline degree of the electrospun meshes. Random and aligned nanofibrous scaffolds were also fabricated by electrospinning of PHB and PHBV with or without type I collagen. The influence of blend composition, fiber alignment and collagen incorporation on Schwann cell (SCs) organization and function was investigated. SCs attached and proliferated over all scaffolds formulations up to 14 days. SCs grown on aligned PHB/PHBV/collagen fibers exhibited a bipolar morphology that oriented along the fiber direction, while SCs grown on the randomly oriented fibers had a multipolar morphology. Incorporation of collagen within nanofibers increased SCs proliferation on day 14, GDNF gene expression on day 7 and NGF secretion on day 6. The results of this study demonstrate that aligned PHB/PHBV electrospun nanofibers could find potential use as scaffolds for nerve tissue engineering applications and that the presence of type I collagen in the nanofibers improves cell differentiation.     

神经生长因子与冻干异体神经桥接大鼠神经缺损的研究

实验采用冻干处理的异体神经与外源性神经生长因子（ＮＧＦ）结合来桥接大鼠的坐骨神经１．０ｃｍ的缺损。用雄性Ｗｉｓｔａｒ大鼠进行的四组实验结果表明：冻干处理的异体神经可降低其抗原性,但处理后并不损害雪旺氏细胞（ＳＣ）基底膜的完整性,在移植后可能成为轴突再生的通道和支架;外源性ＮＧＦ与冻干神经结合形成的复合体,可为神经的再生提供一个较好的微环境,具有成为理想桥接材料的可能性     

Electrospinning Growth Factor Releasing Microspheres into Fibrous Scaffolds

This procedure describes a method to fabricate a multifaceted substrate to direct nerve cell growth. This system incorporates mechanical, topographical, adhesive and chemical signals. Mechanical properties are controlled by the type of material used to fabricate the electrospun fibers. In this protocol we use 30% methacrylated Hyaluronic Acid (HA), which has a tensile modulus of ~500 Pa, to produce a soft fibrous scaffold. Electrospinning on to a rotating mandrel produces aligned fibers to create a topographical cue. Adhesion is achieved by coating the scaffold with fibronectin. The primary challenge addressed herein is providing a chemical signal throughout the depth of the scaffold for extended periods. This procedure describes fabricating poly(lactic-co-glycolic acid) (PLGA) microspheres that contain Nerve Growth Factor (NGF) and directly impregnating the scaffold with these microspheres during the electrospinning process. Due to the harsh production environment, including high sheer forces and electrical charges, protein viability is measured after production. The system provides protein release for over 60 days and has been shown to promote primary nerve cell growth.