Design of expanded bed supports for the recovery of plasmid DNA by anion exchange adsorption

In this study we detail the rational design of new chromatographic adsorbents tailored for the capture of plasmid DNA. Features present on current chromatographic supports that can significantly enhance plasmid binding capacity have been identified in packed bed chromatography experiments and blueprints for improved expanded bed adsorbents have been put forward. The characterisation and testing of small (20-40 m) high density (>3.7 g cm^–3) pellicular expanded bed materials functionalised with various anion exchange structures is presented. In studies with calf thymus DNA, dynamic binding capacities of 1.2 and 3.4 mg ml^–1 were recorded for prototype diethylaminoethyl-and polyethylene imine-linked adsorbents which were respectively 25 and 70 fold higher than those of equivalently derivatised commercial expanded bed materials. The prototype polyethylene imine-coupled material exhibited severe sensitivity to inter-particle bridging by nucleic acid polymers, gave low DNA recoveries (<37%) and proved difficult to regenerate. In contrast, few operational difficulties were experienced with the diethylaminoethyl-linked prototype adsorbent and successful high capacity (>0.8 mg ml^–1) capture of plasmid DNA from crude neutralised E. coli lysate was demonstrated.     

Production of plasmid DNA for human gene therapy using modified alkaline cell lysis and expanded bed anion exchange chromatography

We describe a process for the commercial manufacture of therapeutic grade plasmid DNA. The industrially scaleable unit operations employed in this process are: (i) optimized alkaline lysis; (ii) bag filtration; (iii) expanded bed anion exchange chromatography; (iv) ultrafiltration, and (v) size exclusion chromatography. These steps are scaleable alternatives to current approaches to plasmid DNA isolation such as high speed centrifugation for feedstock clarification and solvent precipitation for plasmid concentration, and an efficient alternative to conventional low through-put packed bed chromatography.The process produces plasmid DNA characterized by low level chromosomal DNA, RNA and endotoxin contamination without the use of flammable solvents or toxic reagents and is suitable for therapeutic administration.     

Single-step recovery of ephedrine hydrochloride from raw materials using expanded bed adsorption

Expanded bed adsorption, using a cation resin 001 x 7 Styrene-DVB, was used to recover and purify ephedrine hydrochloride from a powdered herb. The axial liquid-phase dispersion coefficient was about 10(-5) m(2) s(-1) and the recovery yield and purification reached 86% and 22, respectively. Compared with using conventional extraction with dimethylbenzene, this method is safer and also more efficient.     

Partial purification of nattokinase from Bacillus subtilis by expanded bed adsorption

Nattokinase was purified from unclarified Bacillus subtilisculture filtrate using an expanded bed with a purification factor of 8.2 and at a yield of 95%. The optimal pHs for adsorption and elution were 6.0 and 7.0, respectively. The expanded bed route shortened the process time by 8–10 h and increased the yield by 50% when compared with the conventional method.     

Routine manufacture of recombinant proteins using expanded bed adsorption chromatography

Two different recombinant human proteins were purified directly from Pichia pastoris whole cell fermentation broth, containing 30–44% biomass (wet weight percent), by strong cation exchange expanded bed adsorption chromatography. Expanded bed adsorption chromatography provided clarification, product purification and product concentration in a single unit operation at large scale (2000-l nominal fermentation volume). The efficiency of expanded bed adsorption chromatography resulted in a short process time, high process yield, and limited proteolytic degradation of the target proteins. The separations were operated using a 60-cm (d) column run at 14 l/min. For one protein, expanded bed adsorption chromatography resulted in an average product recovery of 113% (relative to fermentation supernatant) and a purity of 89% (n=10). For the other protein, the average product recovery was 99% (relative to fermentation supernatant) and the purity was 62.1 (n=10). Laboratory experiments showed that biomass reduced product dynamic binding capacity for protein 2.     

Pilot scale recovery of monoclonal antibodies by expanded bed ion exchange adsorption

The aim of the investigations was to estimate the scale up properties of an efficient chromatographic first capture step for the recovery of murine IgG₁ from undiluted and unclarified hybridoma cell culture broth using an ion exchange matrix in expanded bed mode. The tested new sulfopropyl-based ion exchange matrix (Streamline^TM SP XL, Amersham Pharmacia Biotech) stands out due to its enhanced capacity compared to its precursor (Streamline^TM SP). Defining the working pH in preliminary electrophoretic analyses (titration curve, SDS-PAGE) and small-scaled chromatographic binding studies showed, that the optimal value for the IgG purification was pH 4.6, where a co-chromatography of the medium supplement albumin (500 mg l^-1, pI = 4.8) could not be avoided. Further scouting experiments dealt with the dynamic capacity of the matrix, which was evaluated by frontal adsorption analysis. In packed bed mode no break-through of the target protein was achieved even after 6.5 mg IgG per ml matrix were applied. These results could not be reproduced in expanded bed mode with cell-free supernatant, where the dynamic capacity was found to be only 1.5 mg IgG/ml SP XL. Processing cell-containing broth resulted in an additional decrease of the value down to 0.5 mg ml^-1, presumably caused by the remarkable biomass adsorption to the matrix. The search for the reasons led to the examination of the hydrodynamic conditions. Buffer experiments with a tracer substance (acetone) pointed out, that the flow in expanded bed was significantly more influenced by back-mixing effects and channel formations than in packed bed. These effects could be compensated with an enhanced viscosity of the liquid phase, which was achieved by the addition of glucose. As a result of the improved hydrodynamic conditions in the expanded bed, the dynamic capacity could be increased from 0.5 to more than 4.5 mg IgG/ml matrix for the processing of cell culture broth with 400 mM glucose. Finally, the scale up from a Streamline^TM 25 to a Streamline^TM 200 column was performed under conditions, which proved to be optimal: 100 L of unclarified hybridoma broth were concentrated with a binding rate of 95% in less than 3.5 hours. Loading the column no break-through of the target protein was achieved. However, the eluate still contained debris and cells, which points out the major disadvantage of the method: the biomass attachment to the matrix.     

A new fluid distribution system for scale-flexible expanded bed adsorption

A new fluid distribution system designed for expanded bed adsorption was introduced and studied in a 150-cm diameter column. Based on fluid application through a rotating distributor, it eradicates the need for perforated plates, meshes, or local mixers. The effect of rotation rate on column performance was examined by fluidizing a 30-cm high bed of supports with tap water and introducing pulses of dye or acetone tracer. Linear bed expansion was seen as the superficial fluid velocity was raised from 170 x h(-1) to 450 cm x h(-1) (3000 L x h(-1) to 8000 L x h(-1)), and there was little change in expansion characteristics as distributor rotation rate was increased from 2.5 to 10 rpm. The distributor was observed to generate a flow pattern suitable for expanded bed adsorption when the supports were fluidized at a superficial fluid velocity of 283 cm center dot h(-1) and dye pulses introduced. At a rotation rate of 2.5 rpm, no significant dead zones were observed, and a discrete band was formed that moved up through the bed. Furthermore, the pattern of dye movement could be used to calculate interstitial linear fluid velocities of 460 cm x h(-1) and 572 cm x h(-1) at the column wall and center, respectively, indicating a parabolic flow profile. The distributor rotation rate giving the best operating conditions was found to be 2.5 rpm when the bed was fluidized at a flow velocity of 283 cm x h(-1) and the residence time distribution of acetone tracer examined. Under these conditions, the coefficient of axial dispersion was 6.1 x 10(-6) m(2) x s(-1) and 29 theoretical plates were measured. When the rotation rate was raised to 10 rpm, the coefficient of axial dispersion increased to 8.08 x 10(-6) m(2) x s(-1) and the number of theoretical plates decreased to 22.     

New expanded bed adsorbents for the recovery of DNA

A 20–40 m pellicular high density (3.7 g cm^–3) expanded bed material has been designed for the capture of DNA and other large macromolecules. Anion exchangers fashioned out of these supports exhibited dramatically enhanced DNA binding capacities over commercial anion exchange adsorbents (6 mg ml^–1, c.f. 50 g ml^–1 at 10% breakthrough), due to a combination of small particle and fuzzy surface architecture created through the coupling of polyethylene imine chains.     

Refolding of protein inclusion bodies directly from E. coli homogenate using expanded bed adsorption chromatography

To avoid the intrinsic problem of aggregation associated with the traditional solution-phase refolding process, we proposed a solid-phase refolding method integrated with the expanded bed adsorption chromatography. The model protein was a fusion protein of recombinant human growth hormone and a glutathione S-transferase fragment. It was demonstrated that the inclusion body proteins in the cell homogenate could be directly refolded with higher yield. To verify the applicability of this method, we have tested with success three types of the starting materials, i.e., rhGH monomer, inclusion bodies containing the fusion protein, and the E. coli cell homogenate. This direct refolding process could reduce the number of the renaturation steps required and allow the refolding at a higher concentration, approximately 2 mg fusion protein per ml resin. This revised version was published online in July 2006 with corrections to the Cover Date.     

Buoyancy-induced mixing during wash and elution steps in expanded bed adsorption

Buoyancy-induced mixing occurs during expanded bed adsorption processes when the feed stream entering the bottom of the system has a lower density than that of the fluid above it. In the absence of a headspace, mixing in the expanded bed can be modeled as a single, well-mixed vessel, with first-order dynamics. In the presence of a headspace, the system exhibits second-order dynamics for the densities typically encountered in protein chromatography, and can be modeled as two well-mixed vessels (the expanded bed and the headspace) arranged in series. In this paper, the mixing dynamics of the expanded bed are described and a mathematical model of the system is presented. Experimental measurements of density changes during the dilution of sucrose and salt solutions in a STREAMLINE 25 column are presented. These show excellent agreement with predictions using the model. A number of strategies for wash and elution in expanded mode, both in the presence and absence of headspace, are discussed.     

Expanded bed adsorption: elution in expanded bed mode

Elution in expanded bed mode has been investigated in the expanded bed adsorption process. Elution was performed at different sample loads and at different liquid velocities using bovine serum albumin as a model. The effect on mixing in the liquid phase and on the volume of the eluted peak were determined. Mixing in the liquid phase was almost unaffected when elution was performed at 100 cm/h, regardless of sample load. However, mixing increased significantly when elution was carried out at high liquid velocities (300 cm/h) at high sample loads. The eluted peak volume increased with liquid velocity and increased sample load. It was approx. 80% higher in expanded bed mode than in packed bed from an adsorbent completely saturated with protein eluted at 300 cm/h.     

Partial purification properties of human epidermal growth factor from recombinant Escherichia coli by expanded bed adsorption

Human epidermal growth factor is a polypeptide hormone having many diverse biological functions. This paper first presents the recovery results of human epidermal growth factor (hEGF) immediately from the fermentation broth of recombinant Escherichia coli by using an expanded bed system (a couple of STREAMLINE25 and ÄKTA explorer 100). The influences of operational conditions such as linear flow rate, gradient length of NaCl concentration, pH and sample concentration on the purification performances of hEGF in expanded and packed bed modes with STREAMLINE DEAE resin were systematically evaluated. After optimization, the practical recovery procedure in the expanded bed mode was carried out on a scaled-up system under the conditions of linear flow rates of 183 cm/h (upward) and 37 cm/h (downward), sample volume of 300 ml and column bed height of 13.8 cm which yielded a primary product of hEGF from the cell-free supernatant containing hEGF after centrifugation at 4000 rev/min for 15 min. As a result, the hEGF concentration in the product was higher than 20% (w/v), the concentration factor was greater than 4.3 and the total yield was higher than 80%, respectively. At the same time, the results of hEGF recovery by using expanded bed adsorption (EBA), packed bed chromatography (PBC) and salting out were compared. The results show that the procedure of hEGF recovery in expanded bed adsorption has some advantages over the other two procedures, because of its higher concentration factor, recovery yield, productivity, hEGF concentration in the primary product and shorter duration of purification run.     

Evaluation of the effect of in-bed sampling on expanded bed adsorption

An expanded bed adsorption (EBA) column (5 cm diameter) has been modified to allow the abstraction of liquid samples from various positions along the height of an expanded bed. As the adsorbent particles were fluidized, in-bed monitoring of key component concentrations during feedstock application, washing and elution was achieved by the withdrawal of liquid samples from the voids within the expanded bed through ports along the wall of the column. Component levels in the withdrawn streams can be assayed using on-line analytical chromatography or samples can be collected and assayed off-line. On-line monitoring can be used to control the duration of the loading stage and as a tool to provide information about the hydrodynamic and adsorption/desorption processes that occur during expanded bed adsorption. Studies of residence time distributions indicated that the modifications to the column do not significantly affect liquid dispersion. Using the adsorption of glucose-6-phosphate dehydrogenase from yeast homogenate on Streamline DEAE as a model system, comparison of breakthrough curves for runs when in-bed monitoring was and was not performed also suggested that separation efficiency is not appreciably affected by in-bed sampling.     

Interfacing Pichia pastoris cultivation with expanded bed adsorption

For improved interfacing of the Pichia pastoris fed-batch cultivation process with expanded bed adsorption (EBA) technique, a modified cultivation technique was developed. The modification included the reduction of the medium salt concentration, which was then kept constant by regulating the medium conductivity at low value (about 8 mS/cm) by salt feeding. Before loading, the low conductivity culture broth was diluted only to reduce viscosity, caused by high cell density. The concept was applied to a one-step recovery and purification procedure for a fusion protein composed of a cellulose-binding module (CBM) from Neocallimastix patriciarum cellulase 6A fused to lipase B from Candida antarctica (CALB). The modified cultivation technique resulted in lower cell death and consequently lower concentration of proteases and other contaminating proteins in the culture broth. Flow cytometry analysis showed 1% dead (propidium-stained) cells compared to 3.5% in the reference process. During the whole process of cultivation and recovery, no proteolysis was detected and in the end of the cultivation, the product constituted 87% of the total supernatant protein. The lipase activity in the culture supernatant increased at an almost constant rate up to a value corresponding to 2.2 g/L of CBM-CALB. In the EBA process, no cell-adsorbent interaction was detected but the cell density had to be reduced by a two-times dilution to keep a proper bed expansion. At flow velocity of 400 cm/h, the breakthrough capacity was 12.4 g/L, the product yield 98%, the concentration factor 3.6 times, the purity about 90%, and the productivity 2.1 g/L x h.     

Recovery of mouse endostatin produced by Pichia pastoris using expanded bed adsorption

Endostatin, a 20 KDa fragment of collagen XVIII, was shown to have an inhibitory effect on angiogenesis and can potentially be used as a tumor growth suppressor. To obtain the amount needed for testing, the protein was successfully cloned and expressed in Pichia pastoris. At the end of the fermentation process, the concentration of the endostatin in the culture was 50 mg per liter, accompanied by 400 gr per liter (wet weight) of biomass. Before the protein can be captured and purified on a packed bed of heparin-Sepharose, the biomass must be removed. Because of the high biomass concentration, conventional biomass removal techniques like centrifugation or filtration are inefficient and cumbersome. Therefore, the expanded-bed adsorption technique was chosen as an alternative approach. An efficient procedure for the initial recovery and purification of the endostatin was developed. The process utilized a cation- exchanger resin instead of a heparin-based affinity resin, because its dynamic capacity was higher, even though it was affected by the high linear flow on the expanded bed. After adjusting the conductivity, pH and biomass concentration, the complete broth was pumped directly on the expanded-bed matrix (Streamline SP XL). Though the yields of protein are similar, the expanded-bed approach is superior to the packed-bed method for several reasons. The expanded-bed process was shorter (only 8 hours compared to 16 hours for the packed bed), it is cheaper, and the product has higher specific activity (29% compared with 18%). Endostatin produced by the expanded-bed adsorption method showed the expected bioactivity and is currently being tested for its potential as a tumor suppressor.     

Cell/adsorbent interactions in expanded bed adsorption of proteins

Expanded bed adsorption (EBA) is an integrated technology for the primary recovery of proteins from unclarified feedstock. A method is presented which allows a qualitative and quantitative understanding of the main mechanisms governing the interaction of biomass with fluidised resins. A pulse response technique was used to determine the adsorption of various cell types (yeast, Gram positive and Gram negative bacteria, mammalian cells and yeast homogenate) to a range of commercially available matrices for EBA. Cells and cell debris were found to interact with the ligands of agarose based resins mainly by electrostatic forces. From the adsorbents investigated the anion exchange matrix showed the most severe interactions, while cation exchange and affinity adsorbents appeared to be less affected. Within the range of biologic systems under study E. coli cells had the lowest tendency of binding to all matrices while hybridoma cells attached to all the adsorbents except the protein A affinity matrix. The method presented may be employed for screening of suitable biomass/adsorbent combinations, which yield a robust and reliable initial capture step by expanded bed adsorption from unclarified feedstock.     

The effect of column verticality on separation efficiency in expanded bed adsorption

The effect of column verticality on liquid dispersion and separation efficiency in expanded bed adsorption columns was investigated using 1 and 5 cm diameter columns. Column misalignment of only 0.15° resulted in the reduction of the Bodenstein number from 140 to 50 for the 1 cm dia. column and from 75 to 45 for the 5 cm dia. column. This degree of misalignment was not detectable by visual assessment of adsorbent particle movement within the column. Depending on the relative importance of transport limitations, kinetic limitations and dispersion to any specific separation, this increase in dispersion with column alignment can significantly affect separation efficiency. Pure protein breakthrough profiles resulting from the application of bovine serum albumin onto STREAMLINE Q XL demonstrated that, at 10% breakthrough, 7.8% more protein could be applied to a vertical 1 cm dia. column compared to the same column misaligned by 0.15°. When an unclarified yeast homogenate was applied to a 1 cm dia. vertical column packed with STREAMLINE DEAE, 10% breakthrough of glucose-6-phosphate dehydrogenase (G6PDH) corresponded to a load 55% greater compared to the same column aligned 0.185° off-vertical. The G6PDH breakthrough curves for vertical and 0.15° off-vertical runs performed using a 5 cm column were essentially indistinguishable.     

Isolation of bacteriocins through expanded bed adsorption using a hydrophobic interaction medium

Two lactic acid bacterium bacteriocins were isolated from fermentation medium through expanded bed adsorption using a hydrophobic interaction gel. First, amylovorin L471, produced by Lactobacillus amylovorus DCE 471, was selected for the optimisation of the loading and eluting conditions. Secondly, the results of the optimisation were applied for the isolation of enterocin RZS C5, a bacteriocin produced by Enterococcus faecium RZS C5. Optimal adsorption was obtained for a medium with concentration of 1.0 M ammonium sulphate and adjusted to pH 4.0 (94.9% for amylovorin L471 and 75.0% for enterocin RZS C5). Elution with 50% ethanol, buffered at pH 6.0, resulted in an optimal total recovery of the bacteriocin activity of 47.6 and 57.6%, respectively. The highest fold purification expressed as the increase in specific activity (AU/mg) corresponded to the highest recovery, being 140- and 1677-fold, respectively. Nevertheless, a total recovery of only 25.6% with an increase of the specific activity of 121 times was obtained after conventional isolation by ammonium sulphate precipitation.     

Removal of poly-histidine fusion tags from recombinant proteins purified by expanded bed adsorption

Enzymatic methods have been used to cleave the C- or N-terminus polyhistidine tags from histidine tagged proteins following expanded bed purification using immobilized metal affinity chromatography (IMAC). This study assesses the use of Factor Xa and a genetically engineered exopeptidase dipeptidyl aminopeptidase-1 (DAPase-1) for the removal of C-terminus and N-terminus polyhistidine tags, respectively. Model proteins consisting of maltose binding protein (MBP) having a C- or N-terminal polyhistidine tag were used. Digestion of the hexahistidine tag of MBP-His(6) by Factor Xa and HT15-MBP by DAPase-1 was successful. The time taken to complete the conversion of MBP-His(6) to MBP was 16 h, as judged by SDS-PAGE and Western blots against anti-His antibody. When the detagged protein was purified using subtractive IMAC, the yield was moderate at 71% although the overall recovery was high at 95%. Likewise, a yield of 79% and a recovery of 97% was obtained when digestion was performed with using "on-column" tag digestion. On-column tag digestion involves cleavage of histidine tag from polyhistidine tagged proteins that are still bound to the IMAC column. Digestion of an N-terminal polyhistidine tag from HT15-MBP (1 mg/mL) by the DAPase-I system was superior to the results obtained with Factor Xa with a higher yield and recovery of 99% and 95%, respectively. The digestion by DAPase-I system was faster and was complete at 5 h as opposed to 16 h for Factor Xa. The detagged MBP proteins were isolated from the digestion mixtures using a simple subtractive IMAC column procedure with the detagged protein appearing in the flowthrough and washing fractions while residual dipeptides and DAPase-I (which was engineered to exhibit a poly-His tail) were adsorbed to the column. FPLC analysis using a MonoS cation exchanger was performed to understand and monitor the progress and time course of DAPase-I digestion of HT15-MBP to MBP. Optimization of process variables such as temperature, protein concentration, and enzyme activity was developed for the DAPase-I digesting system on HT15-MBP to MBP. In short, this study proved that the use of either Factor Xa or DAPase-I for the digestion of polyhistidine tags is simple and efficient and can be carried out under mild reaction conditions.