硼类化合物在滴眼剂中抑菌效力的探讨

探讨硼类化合物(硼酸、硼砂)在滴眼剂中的抑菌效力。通过实验设计不同浓度的硼酸、硼砂供试品组,测定其抑菌效力。结果表明,在牛磺酸滴眼剂品种中,3组供试品组对真菌组达到抑菌效力的判断标准。但在细菌组中,3组供试品组未达到抑菌效力判断标准。在氯霉素滴眼剂中,白色念珠菌98001、金黄色葡萄球菌26003、铜绿假单胞菌10104组均满足抑菌效力的判断标准,但对大肠埃希菌44102未体现出明显抑菌作用。硼类化合物(硼酸、硼砂)在1 mg/m L剂量下即具有一定的抑菌效力。因此在滴眼剂处方设计时,硼类化合物抑菌效力需被正视,同时需结合配伍注意控制使用剂量。     

Determination of active components in rhubarb and study of their hydrophobicity by micellar electrokinetic chromatography

A micellar electrokinetic chromatographic (MEKC) method has been developed for the determination of five anthraquinones and one distyrene derivative in rhubarb. The separation conditions were optimized and two kinds of rhubarb plants and rhubarb-containing medicines were analyzed. The negatively charged solutes migrated toward the anode and were retarded by their interaction with the micelle. Hydrophobicity of the solutes was studied by both MEKC with SDS and SDS-free capillary zone electrophoresis in the buffer of 15 mmol/L NaH(2)PO(4)+ 20 mmol/L borax and 15% ethanol (v/v). Linear correlation between log k' and log P(OW) was obtained for the five anthraquinones in SDS micelle system. The capacity factor, k', and free energy differences delta(deltaG) derived from this method provided fundamental information on the interaction between the solutes and the micelle.     

Measurement of borate in occupational environments

The hydration stability for inhalable borate particles has been characterized as a function of temperature and relative humidity when collected by a field personnel monitor. The rate of hydration was measured for boric acid (B[OH]3); Neobor borax 5 mol (Na2O x 2B2O3 x 5H2O); borax 10 mol (Na2O x 2B2O3 x 10H2O); anhydrous boric acid (B2O3); and anhydrous borax (Na2O x 2B2O3). The particle size is large in bulk commercial products, such that they can be handled and stored without problems. However, inhalable dust particles, in the range of 20 microm (MMD), undergo hydration/dehydration rapidly owing to their high surface-to-volume ratio. The hydration state of a collected air sample was found to be strongly dependent on the conditions of relative humidity and temperature during its collection. As a consequence, the actual chemical species of dust being inspired cannot be identified accurately. Inhalable particles of borax 10 mol placed in a field personal monitoring cartridge and exposed to dry air at 2.0 L/min at 70 degrees F for 7 h undergo rapid dehydration, producing a sodium borate residue having significantly less than four waters of hydration. Likewise, inhalable particles of anhydrous boric acid and anhydrous borax were found to hydrate under normal atmospheric conditions. Borax 5 mol and boric acid were found to be stable to dehydration. In most cases, the specific borate species or borate compounds collected in a field monitor cannot be accurately characterized other than by their boron (B) content.     

Retention of bile salts in micellar electrokinetic chromatography: relation of capacity factor to octanol–water partition coefficient and critical micellar concentration

The capacity factors of 16 anionic cholates (from six bile salts, including their glyco- and tauro-conjugates) were determined in a micellar electrokinetic chromatography (MEKC) system consisting of buffer, pH 7.5 (phosphate–boric acid; 20 mmol/l) with 50 mmol/l sodium dodecyl sulfate (SDS) as micelle former and 10% acetonitrile as organic modifier. The capacity factors of the fully dissociated, negatively charged analytes (ranging between 0.2 and 60) were calculated from their mobilities, with a reference background electrolyte (BGE) without SDS representing “free” solution. For comparison, the capacity factors were derived for a second reference BGE where the SDS concentration (5 mmol/l) is close to the critical micellar concentration (CMC). The capacity factors are compared with the logarithm of the octanol–water partition coefficient, log P_OW, as measure for lipophilicity. Clear disagreement between these two parameters is found especially for epimeric cholates with the hydroxy group in position 7. In contrast, fair relation between the capacity factor of the analytes and their CMC is observed both depending strongly on the orientation of the OH groups, and tauro-conjugation as well. In this respect the retention behaviour of the bile salts in MEKC seems to reflect their role as detergents in living systems, and might serve as model parameter beyond lipophilicity.     

Analysis of synthetic derivatives of peptide hormones by capillary zone electrophoresis and micellar electrokinetic chromatography with ultraviolet-absorption and laser-induced fluorescence detection

Capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC) were used for the analysis of new synthetic derivatives of hypophysis neurohormones--vasopressin and oxytocin, and pancreatic hormone--human insulin (HI) and its octapeptide fragment, derivatized by fluorescent probe, 4-chloro-7-nitrobenzo[1,2,5]oxadiazol (NBD). The suitable composition of background electrolytes (BGEs) was selected on the basis of calculated pH dependence of effective charge of analyzed peptides. Basic ionogenic peptides were analyzed by CZE in the acidic BGE composed of 100 mM H3PO4, 50 mM Tris, pH 2.25. The ionogenic peptides with fluorescent label, NBD, were analyzed in 0.5 M acetic acid, pH 2.5. The best MEKC separation of non-ionogenic peptides was achieved in alkaline BGE, 20 mM Tris, 5 mM H3PO4, with micellar pseudophase formed by 50 mM sodium dodecylsulfate (SDS), pH 8.8. Selected characteristics (noise, detectability of substance, sensitivity of detector) of the UV-absorption detectors (single wavelength detector, multiple-wavelength photodiode array detector (PDA), both of them operating at constant wavelength 206 nm) and laser-induced fluorescence (LIF) detector (excitation/emission wavelength 488/520 nm) were determined. The detectability of peptides in the single wavelength detector was 1.3-6.0 micromol dm(-3) and in the PDA detector 1.6-3.1 micromol dm(-3). The LIF detection was more sensitive, the applied concentration of NBD derivative of insulin fragment in CZE analysis with LIF detection was three orders lower than in CZE with UV-absorption detector, and the detectability of this peptide was improved to 15.8 nmol dm(-3).     

Comparative toxicology of borates

Inorganic borates, including boric acid, Na, ammonium, K, and Zn borates generally display low acute toxicity orally, dermally, and by inhalation. They are either not irritant or mild skin and eye irritants. Exceptions owing to physiochemical properties do occur. Longer-term toxicological studies have been reported mainly on boric acid or borax where the properties are generally similar on an equivalent boron (B) basis. The critical effects in several species are male reproductive toxicity and developmental toxicity. The doses that cause these effects are far higher than any levels to which the human population could be exposed. Humans would need to consume daily some 3.3 g of boric acid (or 5.0 g borax) to ingest the same dose level as the lowest animal NOAEL. No effects on fertility were seen in a population of workers exposed to borates or to a population exposed to high environmental borate levels. There is remarkable similarity in the toxicological effects of boric acid and borax across different species. Other inorganic borates that simply dissociate to boric acid are expected to display similar toxicity, whereas those that do not dissociate simply to boric acid may display a different toxicological profile.     

Effects of flame retardants on the properties of particle boards prepared from cottonseed hulls

The effects of fire retardants on the properties of particle boards made from cottonseed hulls were studied. The boards were treated with (1) 70% borax + 30% boric acid (FR(1)); (2) 60% borax + 25% boric acid + 15% ammonium dihydrogen orthophosphate (FR(2)) and were evaluated for duration of flaming, after-glow, charred area, charred length and per cent loss in weight, along with physico-mechanical properties. Fire retardant properties, water resistance and per cent thickness swelling improved, and bending strength decreased, with increase in concentration of fire retardants. Treatment (2) was found to be the better fire retardants since it served the dual purposes of flame and glow retardation.     

Toxicity and repellency of borate-sucrose water baits to Argentine ants (Hymenoptera: Formicidae)

The oral toxicity of boron compounds to the Argentine ant, Linepithema humile (Mayr), was evaluated in laboratory tests. The ants were provided 25% sucrose water containing 0.5 and 1% boric acid, disodium octaborate tetrahydrate, and borax. Lethal times of these solutions were a function of the concentration of boron. In field tests, the ants showed no discrimination between disodium octaborate tetrahydrate and boric acid. There was a significant reduction in consumption of sucrose water with > 1% boric acid.     

Simultaneous determination of phthalate di- and monoesters in poly(vinylchloride) products and human saliva by gas chromatography-mass spectrometry

This paper reports on the selectivity behaviour of tryptic peptides on a Cu(2+)-loaded immobilised metal ion affinity chromatography (IMAC) support. Ovalbumin was chosen as a model protein for investigation of the selection and separation of histidine-containing peptides by IMAC off-line coupled with capillary electrophoresis and matrix-assisted laser desorption ionisation time-of-flight mass spectrometry (MALDI-TOF). Two of five histidine-containing peptides in addition to some non-histidine-containing peptides from a tryptic digest of ovalbumin were captured by IMAC. To separate and purify the selected peptides, the IMAC sample was analysed by capillary zone electrophoresis (CZE). The sample was not separated by capillary zone electrophoresis, therefore, micellar electrokinetic chromatography (MEKC) using 10-75 mM SDS was used. Analysis of IMAC sample by MEKC, using low concentrations of SDS (10 mM) was characterised by MALDI-TOF. When using SDS at 75 mM, the migration times of reversed-phase fractions of the IMAC sample, were used to identify the peaks. One of the two selected histidine-containing peptides with two histidine residues was identified, analysing the sample by CZE or MEKC.     

Mono-N-acyl-2,6-diaminopimelic acid derivatives: Analysis by electromigration and spectroscopic methods and examination of enzyme inhibitory activity

Thirteen mono-N-acyl derivatives of 2,6-diaminopimelic acid (DAP)—new potential inhibitors of the dapE-encoded N-succinyl-l,l-diaminopimelic acid desuccinylase (DapE; EC 3.5.1.18)—were analyzed and characterized by infrared (IR) and nuclear magnetic resonance (NMR) spectroscopies and two capillary electromigration methods: capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC). Structural features of DAP derivatives were characterized by IR and NMR spectroscopies, whereas CZE and MEKC were applied to evaluate their purity and to investigate their electromigration properties. Effective electrophoretic mobilities of these compounds were determined by CZE in acidic and alkaline background electrolytes (BGEs) and by MEKC in acidic and alkaline BGEs containing a pseudostationary phase of anionic detergent sodium dodecyl sulfate (SDS) or cationic detergent cetyltrimethylammonium bromide (CTAB). The best separation of DAP derivatives, including diastereomers of some of them, was achieved by MEKC in an acidic BGE (500 mM acetic acid [pH 2.54] and 60 mM SDS). All DAP derivatives were examined for their ability to inhibit catalytic activity of DapE from Haemophilus influenzae (HiDapE) and ArgE from Escherichia coli (EcArgE). None of these DAP derivatives worked as an effective inhibitor of HiDapE, but one derivative—N-fumaryl, Me-ester-DAP—was found to be a moderate inhibitor of EcArgE, thereby providing a promising lead structure for further studies on ArgE inhibitors.     

Bacterial overgrowth affects urinary proteome analysis: recommendation for centrifugation, temperature, duration, and the use of preservatives during sample collection

Bacterial overgrowth is one of the major concerns in collection and storage of biofluids, particularly 24-h urine. However, there is no previous systematic analysis of effects of bacterial overgrowth on urinary proteome analysis, and necessity, type, and appropriate concentration of preservatives to prevent bacterial overgrowth in the urine remain unclear. We, therefore, performed such systematic evaluation. Pooled normal urine was either centrifuged at 1500 g (to remove cell debris) or uncentrifuged. The samples were then added with either sodium azide (NaN3) or boric acid with various concentrations, and kept at room temperature (RT) or at 4 degrees C. Bacterial overgrowth was determined by UV-visible spectrophotometry (lambda620 nm) and Gram staining. At both temperatures, centrifugation to remove cell debris could effectively delay the bacterial overgrowth. At RT, both centrifuged and uncentrifuged samples without any preservative had the detectable overgrowth of Gram-positive and Gram-negative cocci and bacilli as early as 12 and 8 h, respectively, whereas 0.1-1 mM NaN3 and 2-20 mM boric acid could delay bacterial overgrowth, which started at 16-20 h in the centrifuged urine and 12-16 h in the uncentrifuged urine. Greater delay (for at least 48 h) was achieved with 10 mM NaN3 and 200 mM boric acid. At 4 degrees C, no bacterial overgrowth was detected in all centrifuged samples. However, it was observed at 20 h in the uncentrifuged urine without preservative, and at 48 h for the uncentrifuged urine with 0.1 mM NaN3 or 2 mM boric acid. There was no bacterial overgrowth detectable in the uncentrifuged urine preserved with higher concentrations of NaN3 or boric acid. 2-DE showed obvious changes in the urinary proteome profile of the sample with bacterial contamination, and the bacterial proteins could be identified by MALDI-TOF MS. Our data suggest that the urine should be centrifuged to remove cell debris and kept at 4 degrees C, rather than at RT, during the collection interval prior to long-term storage in the freezer. Moreover, the addition of 200 mM boric acid or 10 mM NaN3 is highly recommended for the prevention of bacterial overgrowth in the urine.     

Determination of andrographolide,deoxyandrographolide and neoandrographolide in the Chinese herb Andrographis paniculata by micellar electrokinetic capillary chromatography

In this paper a micellar electrokinetic capillary chromatographic (MEKC) method has been developed for determining the active components (andrographolide, deoxyandrographolide and neoandrographolide) in water:ethanol extracts of the Chinese crude herb Andrographis paniculata and its preparations (Chuanxinlian and Xiaoyan Lidan tablets). The optimum separation conditions were 15 mM sodium dodecyl sulphate in 30 mM borate buffer (pH 9.5) with UV detection wavelength at 214 nm and a constant voltage of 16 kV. An HPLC method was employed in order to validate the MEKC method with respect to separation efficiency, sensitivity, linearity and repeatability. The two methods are shown to be complementary because of their different selectivity and thus are very suitable for cross-validation studies. The MEKC method is demonstrated to be more appropriate for the analysis of the active compounds in A. paniculata in that it is easier and less expensive to use and does not suffer from contamination of the chromatographic column.     

Micellar electrokinetic chromatography-electrospray ionization mass spectrometry for the identification of drug impurities

Previously, we have presented a system hyphenating continuous micellar electrokinetic chromatography (MEKC) with electrospray ionization mass spectrometry (ESI-MS). Here we evaluate this technique for its applicability in impurity profiling of drugs using galantamine and ipratropium as test samples. A background electrolyte (BGE) of 10mM sodium phosphate (pH 7.5), 12.5-15% acetonitrile and 20mM sodium dodecylsulfate (SDS) was used for the MEKC-MS analysis of a galantamine sample containing a number of related impurities, and a heat-treated solution of ipratropium containing a number of unknown degradation products. MEKC provided efficient separation of all sample constituents. Despite the presence of non-volatile BGEs, all impurities in the galantamine sample could be detected by ESI-MS in their respective extracted ion traces (XICs) with a detection sensitivity in the sub-microg/ml range (full-scan mode). MS/MS detection provided useful product spectra allowing the structural characterization of the respective galantamine impurities. With the MEKC-MS/MS system, two degradation products could be revealed and identified in the heat-stressed ipratropium sample. The presented method shows good potential for the detection and structure elucidation of minor impurities in drug substances.     

Fluorometric characterization of dityrosine: complex formation with boric acid and borate ion

Borate/boric acid solutions have distinctive effects on the absorption and fluorescence emission spectra of dityrosine. In the presence of excess borate/boric acid, the fluorescence emission maximum of the singly ionized dityrosine chromophore shifts from 407 nm (quantum yield = 0.80) to 374 nm (quantum yield = 0.14). Fluorescence measurements performed as a function of pH and concentration are consistent with a 1:1 complex which may dissociate to either boric acid and singly ionized dityrosine (K1 = 17 mM) or to monoborate ion and unionized dityrosine (K2 = 0.10 mM). As a consequence of the pKa values characteristic of dityrosine and boric acid, complex formation is maximal near pH 8. 2,2'-Dihydroxy-biphenyl shows similar interactions. The fluorescence of dityrosyl calmodulin (0 Ca2+) also responds to the addition of boric acid, giving K1 = 42 mM and K2 = 2 mM. Singly ionized dityrosine produced through dissociation occurring in the excited state does not interact with boric acid.     

Determination of three bile acids in artificial Calculus Bovis and its medicinal preparations by micellar electrokinetic capillary electrophoresis

A micellar electrokinetic capillary electrophoresis (MEKCE) method for the determination of cholic acid (CA), hyodeoxycholic acid (HDCA) and chenodeoxycholic acid (CDCA) in artificial Calculus Bovis and its four medicinal preparations is described. The buffer solution consisted of 40 mM disodic phosphate and 40 mM sodium dodecylsulfate (SDS) adjusted to pH 9.0. UV detection was set to 200 nm. Under optimum conditions, the analytes were baseline separated within 11min. The linear calibration range was 12.1-970 microgml(-1) for CA and 18.8-950 microgml(-1) for HDCA and CDCA, respectively. It was found that overall recoveries were within the range of 98-102%, and R.S.D.s were less than 5% for the analytes. This method, due to its convenience, high accuracy and good reproducibility can be employed in quality control of artificial Calculus Bovis and its medicinal preparations.     

Validation of a rapid micellar electrokinetic capillary chromatographic method for the simultaneous determination of isoniazid and pyridoxine hydrochloride in pharmaceutical formulation

An efficient and reliable micellar electrokinetic capillary chromatography (MEKC) method has been developed for the simultaneous determination of isoniazid (ISO) and pyridoxine hydrochloride (PYR) in pharmaceutical formulations. A chemometric two level full factorial design approach was used to search for the optimum conditions of separation. Three parameters were selected for this study: the buffer pH, the buffer concentration and sodium dodecyl sulphate (SDS) concentrations. Resolution, peak symmetry and analysis time were established as response. The two analytes were separated within 6 min with the optimized conditions: 50 mM borate buffer, 25 mM SDS pH 7.8, 35 degrees C, at 50 mbar 4s injection and 30 kV by using a fused silica capillary (72 cm effective length, 50 microm i.d.). The detection wavelength was set to 205 nm. Meloxicam was used as internal standard. The method was validated with respect to stability, linearity range, limit of quantitation and detection, precision, accuracy, specificity and robustness. The detection limits of the method were 1.0 microg mL(-1) for ISO and 0.40 microg mL(-1) for PYR and the method was linear at least in the range of 3.0-100 microg mL(-1) for ISO and 1.0-100 microg mL(-1) for PYR with excellent correlation coefficients (0.9995 for ISO and 0.9998 for PYR). Relative standard deviations (R.S.D.s) of the described method ranged between 0.54 and 2.27% for intra-day precision and between 0.65 and 2.69% for inter-day precision. The developed method was applied to the tablet form of ISO and PYR-containing the pharmaceutical preparations and the data were compared with obtained from the standard addition method. No statistically significant difference was found.     

Strain variability and the effects of organic compounds on the growth of the chemolithotrophic bacterium Thiobacillus ferrooxidans

The effects of naturally-occurring organic compounds on ferrous iron oxidation by the bacterium Thiobacillus ferrooxidans were examined with a view to using these compounds to treat or prevent acid mine/rock drainage. The compounds glucose, cellobiose, galacturonic acid, and citric acid were added to the growth medium of five different strains of the bacterium and growth studies were done to determine whether or not strain differences existed with respect to organic compound sensitivity. The effects of these compounds were compared to the effects of sodium dodecyl sulfate (SDS) an anionic detergent. Each of the compounds tested had an inhibitory effect on the strains of the bacterium and sensitivity to these compounds was strain dependent. All strains appeared to be equally susceptible to SDS. Inhibitory concentrations ranged from 70 mM to >280 mM for glucose, 7.5 mM to 150 mM for cellobiose, 20 mM to 230 mM for galacturonic acid, and 50 mM to 130 mM for citric acid. SDS effectively inhibited iron oxidation for all strains at a concentration of 0.3 mM, the lowest concentration tested. Some naturally-occurring organic compounds, therefore, might be candidates for the growth control of T. ferrooxidans.     

Separation of bisbenzylisoquinoline alkaloids by micellar electrokinetic chromatography

The micellar electrokinetic chromatographic (MEKC) separation of seven bisbenzylisoquinoline alkaloids has been developed. The effects of various separating factors were studied. Optimum separation was achieved using a buffer (pH 9.2) of 20 mM sodium borate and 20 mM sodium dihydrogen phosphate buffer containing 55 mM sodium cholate; the optimum voltage and injection time were 21 kV and 0.05 min, respectively. Highest peak efficiency was obtained when the analytes were dissolved in 10 mM sodium dodecyl sulphate as sample matrix for injection. The elution order of the bisbenzylisoquinoline alkaloids was related to their lipophilicity. The resolution, run time and detection limits of the MEKC method were compared with those of an HPLC method developed previously.     

Simultaneous determination of catecholamines and polyamines in PC-12 cell extracts by micellar electrokinetic capillary chromatography with ultraviolet absorbance detection

A method for simultaneous determination of polyamines and catecholamines in cell extracts by micellar electrokinetic capillary chromatography with UV detection at 254 nm was established at the first time. The polyamines (putrescine, spermidine and spermine) and catecholamines (dopamine, serotonin, norepinephrine and epinephrine) were extracted from PC-12 cells and were derivatized with 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate. Different derivatization conditions such as temperature, ratio of derivatization reagents and incubation time were investigated to find the best reaction condition which gave the highest detection sensitivity for polyamines and catecholamines. The influence of running buffer and additives on the separation such as pH, sodium dodecyl sulfate (SDS) concentrations and various additives was also investigated. Separation was achieved within 20 min with good repeatability in a 100mM boric acid buffer containing 10mM SDS and 10mM 18-crown-6 at a pH of 9.5. The detection limit ranged from 1.0 x 10(-7) to 9.0 x 10(-7) M, which is sufficient for determination of polyamines and catecholamines in many cell extracts. This technique can be easily applied to polyamine-related anticancer drug studies or clinical follow-ups after each dosage of these anticancer drugs, since these drugs not only have great inhibition on polyamine levels in blood, but also have a large influence on catecholamine levels in blood.     

Is Boron a Prebiotic Element? A Mini-review of the Essentiality of Boron for the Appearance of Life on Earth

Boron is probably a prebiotic element with special importance in the so-called "sugars world". Boron is not present on Earth in its elemental form. It is found only in compounds, e.g., borax, boric acid, kernite, ulexite, colemanite and other borates. Volcanic spring waters sometimes contain boron-based acids (e.g., boric, metaboric, tetraboric and pyroboric acid). Borates influence the formation of ribofuranose from formaldehyde that feeds the "prebiotic metabolic cycle". The importance of boron in the living world is strongly related to its implications in the prebiotic origins of genetic material; consequently, we believe that throughout the evolution of life, the primary role of boron has been to provide thermal and chemical stability in hostile environments. The complexation of boric acid and borates with organic cis-diols remains the most probable chemical mechanism for the role of this element in the evolution of the living world. Because borates can stabilize ribose and form borate ester nucleotides, boron may have provided an essential contribution to the "pre-RNA world".