Sorption of Acid Blue 9 Using Hydrilla verticillata Biomass—Optimization,Equilibrium, and Kinetics Studies

In the present study, the parameters, temperature, adsorbent dose, contact time, adsorbent size, and agitation speed were optimized for Acid Blue 9 removal from aqueous medium by Hydrilla verticillata biomass using response surface methodology (RSM). The optimum conditions for maximum removal of Acid Blue 9 from an aqueous solution of 100 mg/L were as follows: temperature 30.63°C, adsorbent dose 2.88 g/L, contact time 180 min, adsorbent size 120 mesh (0.124 mm), and agitation speed 237.39 rpm. At these optimized conditions, batch adsorption experiments were conducted to study the effect of pH and initial dye concentration for the removal of Acid Blue 9 dye. The optimum initial pH and initial dye concentration values for Acid Blue 9 removal were found to be 3.0 and 100 mg/L, respectively. Kinetic and equilibrium studies were carried out for the experimental results. From the kinetic studies it was found that pseudo-second-order kinetics suits the system well. From the equilibrium studies, the Freundlich isotherm fits the data well.     

Adsorption of metal complex dyes from aqueous solutions by pine sawdust

An attempt to alleviate the problem caused by the presence of metal complex dyes, mostly used in textile industries, in the textile effluents was undertaken. The effects of adsorbent particle size, pH, adsorbent dose, contact time and initial dye concentrations on the adsorption of metal complex dyes by pine sawdust was investigated. Acidic pH was favorable for the adsorption of metal complex dyes. A contact time of 120 min was required to reach the equilibrium. The experimental isotherm data were analyzed using the Langmuir, Freundlich and Temkin equations. The equilibrium data fit well the Langmuir isotherm. The monolayer adsorption capacities are 280.3 and 398.8 mg dye per g of pine sawdust for Metal Complex Blue and Metal Complex Yellow, respectively. The results indicate that pine sawdust could be employed as low-cost alternative to commercial activated carbon in aqueous solution for the removal of metal complex dyes.     

Cationized starch-based material as a new ion-exchanger adsorbent for the removal of C.I. Acid Blue 25 from aqueous solutions

This article describes the use of a cationized starch-based material as new ion-exchanger adsorbent for the removal of C.I. Acid Blue 25 (AB 25) from aqueous solutions. Batch adsorption studies concerning the effects of contact time, pH and temperature are presented and discussed. Adsorption experimental data showed that: (i) the process was uniform and rapid: adsorption of dye reached equilibrium in 50 min in the wide pH range of dye solutions; (ii) adsorption kinetics followed the pseudo-second order model; (iii) the Langmuir model yielded a much better fit than the Freundlich model for the dye concentration range under study; (iv) this adsorbent exhibited interesting adsorption capacities: on the basis of the Langmuir analysis, the maximum adsorption capacity was determined to be 322 mg of dye per gram of material at 25 degrees C; (v) the adsorption capacity decreased with increasing temperature; and (vi) the negative value of free energy change indicated the spontaneous nature of adsorption.     

Feasibility of using <Emphasis Type="Italic">Trichoderma harzianum</Emphasis> biomass for the removal of erioglaucine from aqueous solution

The test fungus Trichoderma harzianum was isolated from the Western Ghats area of Tamilnadu, India. The study involves the feasibility of using T.harzianum to remove erioglaucine from an aqueous solution in batch mode. The batch mode experimental parameters such as effect of agitation time and initial dye concentration, adsorbent mass and pH were determined. The results revealed that, the fungal biomass at 1.5 g/50 ml adsorbent mass removed 75.67–88.05% of dye (10–50 mg/l) in 105 min at pH 4.0. The adsorption equilibrium data followed both Langmuir and Freundlich isotherms. From the Langmuir isotherm, the adsorbent had adsorption capacity (Q ₀ ) of 3.09 mg/g. Pseudo first and second order rate kinetic equations were applied to the experimental adsorption data. The results indicate that the adsorbent system followed second order rate kinetics.     

Adsorption of methylene blue using green pea peels (Pisum sativum): A cost-effective option for dye-based wastewater treatment

Methylene blue (MB), a common toxic dye, is largely discharged from dyeing processes for acrylic, nylon, silk, and woolen fabrics in textile industries. While application of conventional removal processes like chemical precipitation, ion exchange, commercial activated carbon adsorption, etc often become cost-prohibitive, the adsorption of MB by abundantly available green pea peel (GPP: Pisum sativum) derived and acid-treated carbon (GPP-AC) has proved to be a cost-attractive option in the present study. The physicochemical and morphological characteristics of GPP-AC were examined with the help of XRD, BET surface area, SEM, and Fourier transform infrared spectrophotometry ((FT-IR) analysis. The influences of such adsorption parameters as initial dye concentration, pH, contact time, adsorbent dosage, agitation speed, particle size, and temperature were evaluated and optimized. The equilibrium contact time for maximum adsorption of MB on to GPPAC was found to be 7 h. The equilibrium data of the adsorption process were modeled by using the Langmuir, Freundlich, Temkin, and Dubinin-Raduskevich (D-R) isotherms. However, the adsorption equilibrium data were best described by the Langmuir Isotherm model, with a maximum adsorption capacity of 163.94 mg MB/g GPPAC at 30°C.     

Comparing the performance of granular coral limestone and Leca in adsorbing Acid Cyanine 5R from aqueous solution

The effect of granular coral limestone and Leca as adsorbents for removing Acid Cyanine 5R (AC5R) from aqueous solution was studied. The optimum pH and adsorbent particles size in both adsorbents were determined to be 3 and 297 μm, respectively. The optimum dosages of coral limestone and granular Leca were 0.150 and 0.145 g/mg of dye, respectively. Also, results have shown that the adsorption efficiency by both coral limestone and Leca increased with the decreasing adsorbent particles size. Moreover, under similar conditions, the maximum removal efficiency by granular coral limestone and Leca was 94% and 88%, respectively. The results revealed that the performance of granular coral limestone was better in AC5R removal than that of Leca granulated under such condition. In total, granular coral limestone and Leca act as suitable adsorbents for removing dye pollutants from an aqueous solution.     

Removal of nickel(II) from aqueous solution by adsorption on agricultural waste biomass using a response surface methodological approach

In the present study, effect of adsorbent dose, pH and agitation speed on nickel removal from aqueous medium using an agricultural waste biomass, Sugarcane bagasse has been investigated. Batch mode experiments were carried out to assess the adsorption equilibrium. The influence of three parameters on the removal of nickel was also examined using a response surface methodological approach. The central composite face-centered experimental design in response surface methodology (RSM) by Design Expert Version 6.0.10 (Stat Ease, USA) was used for designing the experiments as well as for full response surface estimation. The optimum conditions for maximum removal of nickel from an aqueous solution of 50 mg/L were as follows: adsorbent dose (1500 mg/L), pH (7.52) and stirring speed (150 rpm). This was evidenced by the higher value of coefficient of determination (r(2)=0.9873).     

Removal of Astrazon Yellow 7GL from aqueous solutions by adsorption onto wheat bran

Adsorption kinetic and equilibrium of a basic dye (Astrazon Yellow 7GL) from aqueous solutions at various initial dye concentration (50-300 mg/l), pH (4-10), adsorbent dosage (2-8 g/l), particle size (354-846 microm) and temperature (30-50 degrees C) on wheat bran were studied in a batch mode operation. The result showed that the amount adsorbed of the dye increased with increasing initial dye concentration and contact time, whereas particle size and pH had no significant affect on the amount of dye adsorbed by the adsorbent. A comparison of kinetic models on the overall adsorption rate showed that dye/adsorbent system was best described by the pseudo second-order rate model. The removal rate was also dependent on both external mass transfer and intra-particle diffusion. The low value of the intraparticle diffusivity, 10(-11) cm2/s, indicated the significant influence of intraparticle diffusion on the kinetic control. The adsorption capacity (Q0) calculated from the Langmuir isotherm was 69.06 mg/g for at pH 5.6, 303 K for the particle size of 354 microm. The experimental data yielded excellent fits with Langmuir and Tempkin isotherm equations. Different thermodynamic parameters showed that the reaction was spontaneous and endothermic in nature.     

Biosorption of Methylene Blue by De-Oiled Algal Biomass: Equilibrium,Kinetics and Artificial Neural Network Modelling

The main objective of the present study is to effectively utilize the de-oiled algal biomass (DAB) to minimize the waste streams from algal biofuel by using it as an adsorbent. Methylene blue (MB) was used as a sorbate for evaluating the potential of DAB as a biosorbent. The DAB was characterized by SEM, FTIR, pH_PZC, particle size, pore volume and pore diameter to understand the biosorption mechanism. The equilibrium studies were carried out by variation in different parameters, i.e., pH (2–9), temperature (293.16–323.16 K), biosorbent dosage (1–10 g L⁻¹), contact time (0–1,440 min), agitation speed (0–150 rpm) and dye concentration (25–2,500 mg L⁻¹). MB removal was greater than 90% in both acidic and basic pH. The optimum result of MB removal was found at 5–7 g L⁻¹ DAB concentration. DAB removes 86% dye in 5 minutes under static conditions and nearly 100% in 24 hours when agitated at 150 rpm. The highest adsorption capacity was found 139.11 mg g⁻¹ at 2,000 mg L⁻¹ initial MB concentration. The process attained equilibrium in 24 hours. It is an endothermic process whose spontaneity increases with temperature. MB biosorption by DAB follows pseudo-second order kinetics. Artificial neural network (ANN) model also validates the experimental dye removal efficiency (R² = 0.97) corresponding with theoretically predicted values. Sensitivity analysis suggests that temperature and agitation speed affect the process most with 23.62% and 21.08% influence on MB biosorption, respectively. Dye adsorption capacity of DAB in fixed bed column was 107.57 mg g⁻¹ in preliminary study while it went up to 139.11 mg g⁻¹ in batch studies. The probable mechanism for biosorption in this study is chemisorptions via surface active charges in the initial phase followed by physical sorption by occupying pores of DAB.     

Experimental and kinetic studies on methylene blue adsorption by coir pith carbon

Varying the parameters such as agitation time, dye concentration, adsorbent dose, pH and temperature carried out the potential feasibility of thermally activated coir pith carbon prepared from coconut husk for removal of methylene blue. Greater percentage of dye was removed with decrease in the initial concentration of dye and increase in amount of adsorbent used. Kinetic study showed that the adsorption of dye on coir pith carbon was a gradual process. Lagergren first-order, second-order, intra particle diffusion model and Bangham were used to fit the experimental data. Equilibrium isotherms were analysed by Langmuir, Freundlich, Dubnin-Radushkevich, and Tempkin isotherm. The adsorption capacity was found to be 5.87 mg/g by Langmuir isotherm for the particle size 250-500 microm. The equilibrium time was found to be 30 and 60 min for 10 and 20 mg/L and 100 min for 30, 40 mg/L dye concentrations, respectively. A maximum removal of 97% was obtained at natural pH 6.9 for an adsorbent dose of 100 mg/50 mL and 100% removal was obtained for an adsorbent dose of 600 mg/50 mL of 10 mg/L dye concentration. The pH effect and desorption studies suggest that chemisorption might be the major mode of the adsorption process. The change in entropy (DeltaS0) and heat of adsorption (DeltaH0) of coir pith carbon was estimated as 117.20 J/mol/K and 30.88 kJ/mol, respectively. The high negative value of change in Gibbs free energy indicates the feasible and spontaneous adsorption of methylene blue on coir pith carbon.     

Utilization of ground eggshell waste as an adsorbent for the removal of dyes from aqueous solution

The adsorption of cationic basic blue 9 and anionic acid orange 51 from aqueous solution onto the calcified eggshell (ES) and its ground eggshell powder (ESP) was carried out by varying the process parameters such as agitation speed, initial dye concentration, adsorbent mass and temperature. The adsorption potential for basic blue 9 onto ESP is far lower than that for acid orange 51, mainly due to the ionic interaction between the acid dye with the sulfonate groups and the positively charged sites on the surface of ESP. The adsorption capacity of acid orange 51 onto ES is significantly smaller than that onto ESP, which is in line with their pore properties (i.e., 1 vs. 21 m(2)/g). The experimental results showed that the adsorption process can be well described with a simple model, the pseudo-second-order model. According to the equilibrium adsorption capacity from the fitting of pseudo-second order reaction model, it was further found that the Freundlich model yields a somewhat better fit than the Langmuir model in the adsorption of acid orange 51 onto ESP. In addition, an increase in adsorption temperature from 15 to 45 degrees C significantly enhances the adsorption capacity of acid orange 51 onto ESP, revealing that the adsorption should be an endothermic or chemisorption process. From the results, it is feasible to utilize the ground eggshell waste as an effective adsorbent for removal of anionic dye from aqueous solution.     

Removal of Acid Blue25 from aqueous solutions using Bengal gram fruit shell (BGFS) biomass

The feasibility for the removal of Acid Blue25 (AB25) by Bengal gram fruit shell (BGFS), an agricultural by-product, has been investigated as an alternative for high-cost adsorbents. The impact of various experimental parameters such as dose, different dye concentration, solution pH, and temperature on the removal of Acid Blue25 (AB25) has been studied under the batch mode of operation. pH is a significant impact on the sorption of AB25 onto BGFS. The maximum removal of AB25 was achieved at a pH of 2 (83.84%). The optimum dose of biosorbent was selected as 200 mg for the removal of AB25 onto BGFS. Kinetic studies reveal that equilibrium reached within 180 minutes. Biosorption kinetics has been described by Lagergren equation and biosorption isotherms by classical Langmuir and Freundlich models. Equilibrium data were found to fit well with the Langmuir and Freundlich models, and the maximum monolayer biosorption capacity was 29.41 mg g^?1 of AB25 onto BGFS. The kinetic studies indicated that the pseudo-second-order (PSO) model fitted the experimental data well. In addition, thermodynamic parameters have been calculated. The biosorption process was spontaneous and exothermic in nature with negative values of ΔG° (?1.6031 to ?0.1089 kJ mol^?1) and ΔH° (?16.7920 kJ mol^?1). The negative ΔG° indicates the feasibility of physical biosorption process. The results indicate that BGFS could be used as an eco-friendly and cost-effective biosorbent for the removal of AB25 from aqueous solution.     

Utilization of modified silk cotton hull waste as an adsorbent for the removal of textile dye (reactive blue MR) from aqueous solution

Carbon prepared from silk cotton hull was used to remove a textile dye (reactive blue MR) from aqueous solution by an adsorption technique under varying conditions of agitation time, dye concentration, adsorbent dose and pH. Adsorption depended on solution pH, dye concentration, carbon concentration and contact time. Equilibrium was attained with in 60 min. Adsorption followed both Langmuir and Freundlich isotherm models. The adsorption capacity was found to be 12.9 mg/g at an initial pH of 2+/-0.2 for the particle size of 125-250 microm at room temperature (30+/-2 degrees C).     

Waste biomass of Nostoc linckia as adsorbent of crystal violet dye: Optimization based on statistical model

The potential of spent biomass of a hydrogen producing cyanobacterial strain Nostoc linckia from a hydrogen fermentor was studied for decolorization of a tri-phenylmethane dye, crystal violet. The waste cyanobacterial biomass immobilized in calcium alginate was used as a biosorbent and the process variables were optimized for maximum dye removal using the statistical response surface methodology (RSM). Batch mode experiments were performed to determine the kinetic behavior of the dye in aqueous solution allowing the computation of kinetic parameters. Influence of interacting parameters like temperature (25-35 °C), pH (4-8), initial dye concentration (100-200 mg/L) and cyanobacterial dose (0.2-0.4 g) on dye removal were examined using central composite design (CCD) which included two additional levels for each parameter. Second-order polynomial regression model, was applied which was statistically validated using analysis of variance. Ability of the immobilized biomass to decolorize the dye was maximum (72%) at pH 8.0, temperature 35 °C, 200 mg/L initial dye concentration and 0.2 g cyanobacterial dose. Adsorption of the dye on cell surface was further confirmed by scanning electron micrographs of the biomass before and after dye loading. FT-IR studies revealed that decolorization was due to biosorption mediated mainly by functional groups like hydroxyl, amide, carboxylate, methyl and methylene groups present on the cell surface.     

Comparison of activated carbon and bottom ash for removal of reactive dye from aqueous solution

The adsorption of reactive dye from synthetic aqueous solution onto granular activated carbon (GAC) and coal-based bottom ash (CBBA) were studied under the same experimental conditions. As an alternative to GAC, CBBA was used as adsorbent for dye removal from aqueous solution. The amount of Vertigo Navy Marine (VNM) adsorbed onto CBBA was lower compared with GAC at equilibrium and dye adsorption capacity increased from 0.71 to 3.82 mg g(-1), and 0.73 to 6.35 mg g(-1) with the initial concentration of dye from 25 to 300 mg l(-1), respectively. The initial dye uptake of CBBA was not so rapid as in the case of GAC and the dye uptake was slow and gradually attained equilibrium.     

Adsorption of methylene blue dye from aqueous solution by sugar extracted spent rice biomass

This study was aimed at using sugar extracted spent rice biomass (SRB) as a potential adsorbent to remove methylene blue (MB) dye from aqueous solution. The SRB was used without any modification. A three factor full factorial experimental design (2(3)) was employed to investigate the effect of factors (adsorbent dose, dye concentration, temperature) and their interaction on the adsorption capacity and color removal. Two levels for each factor were used; adsorbent dose (0.25-0.5g/100mL), dye concentration (25-50mg/L), and temperature (25-45°C). Initial dye concentration and adsorbent dosage were found as significant factors for the adsorption of MB dye. Langmuir isotherm (R(2)>0.998) best explained the equilibrium of MB adsorption on SRB with monolayer adsorption capacity of 8.13mg/g. The pseudo-second order model (R(2)>0.999) was best fitted to explain the adsorption kinetics. Thermodynamic investigation revealed that the adsorption process was spontaneous, endothermic, and was feasible to treat dyeing wastewater.     

Microwave assisted thermal treatment of defective coffee beans press cake for the production of adsorbents

Defective coffee press cake, a residue from coffee oil biodiesel production, was evaluated as an adsorbent for removal of basic dyes (methylene blue – MB) from aqueous solutions. The adsorbent was prepared by microwave treatment, providing a significant reduction in processing time coupled to an increase in adsorption capacity in comparison to conventional carbonization in a muffle furnace. Batch adsorption tests were performed at 25 °C and the effects of particle size, contact time, adsorbent dosage and initial solution pH were investigated. Adsorption kinetics was better described by a second-order model. The experimental adsorption equilibrium data were fitted to Langmuir, Freundlich and Tempkin adsorption models, with Langmuir providing the best fit. The results presented in this study show that microwave activation presents great potential as an alternative method in the production of adsorbents.     

A sustainable process for adsorptive removal of methylene blue onto a food grade mucilage: kinetics,thermodynamics, and equilibrium evaluation

Abstract

Adsorption of dyes onto natural materials like polysaccharides is considered a green chemistry approach for remediation of wastewater. In this work, the polysaccharide isolated from the corm of Colocasia esculenta (L.) Schott or taro tuber (CEM) was utilized for removing methylene blue (MB) from aqueous solution by batch adsorption method. The CEM adsorbent was characterized by FTIR spectroscopy, Brunauer–Emmett–Teller (BET), and scanning electron microscopy (SEM). The solution pH and adsorbent dose have been found to have a significant positive correlation with the adsorptive removal efficiency of CEM for MB dye. The removal efficiency of CEM was found to be 72.35% under the optimum conditions; 20?mg/L initial concentration of dye, 120?mg of adsorbent dose, solution pH 8.5, 311.2?K temperature and 80?min contact time. The adsorption of MB onto CEM followed best the Freundlich isotherm and pseudo-second-order kinetics. The adsorption was thermodynamically favorable and was endothermic in nature. The desorption/adsorption data justifiably indicated the reuse capability of CEM adsorbent for MB adsorption. Hence, CEM may be regarded as an eco-friendly and cost-effective natural adsorbent for MB dye removal from aqueous solution.