拉曼被孢霉F_5发酵生产γ—亚麻酸的研究

对拉曼被孢霉突变株F5发酵生产γ—亚麻酸的最适碳源、氮源、发酵时间及温度、无机盐离子添加、最适碳源浓度及补加碳源时间等发酵条件进行了研究探讨。最适发酵培养基组成为 (g/L) :葡萄糖 1 0 0 ,酵母浸出粉 4 ,蛋白胨 1 ,K2 HPO4 1 ,CaCl2 1× 1 0 - 2 ,MgSO4 5× 1 0 - 2 ,FeSO4 1× 1 0 - 2 ,ZnSO4 7.5× 1 0 - 3,CuSO4 0 .5× 1 0 - 3,MnSO4 2× 1 0 - 3,pH 6.0。培养温度为 2 5℃ ,1 4 0r/min振荡培养 1 0天 ,培养 8天后 (即收获前 2天 )补加 5 %葡萄糖。发酵结果为 :DC 2 4 .5 9g/L ,TL 1 0 .84g/L ,TL/DC 4 4.0 9% ,GLA/TL 1 0 .67% ,GLA产量为 1 1 5 6.63mg/L。GLA产量较初始结果提高 1 5 6.1 5 %。该菌株已达到工业化生产菌株要求     

红酵母类胡萝卜素形成的生理学研究

从数株红酵母中选出 1株产类胡萝卜素能力较强的红酵母RY 98(生物量、类胡萝卜素含量和产量分别为19.9g/L ,334 .8μg/ g和 6 .7mg/L) ;研究了该菌株产类胡萝卜素的最适营养与环境条件 ,获得了最佳的发酵生理学条件 :葡萄糖 40 g/L ,(NH4 ) 2 SO4 10 g/L ,酵母膏 3g/L ,蕃茄汁 2mL/L ,花生油 0 .5mL/L ,接种量 30mL/L ,初始pH 6 .0和通气量 (培养基装量 ) 4 0mL/ 2 5 0mL。在此初步优化的培养条件下 ,红酵母RY 98经 72h摇瓶发酵其生物量、类胡萝卜素含量和产量分别可达 2 6 .8g/L ,386 .9μg/ g和 10 .4mg/L ,依次比初筛中提高了 34 .7% ,15 .6 %和 5 5 .2 %。     

暹罗芽胞杆菌FJAT-45551用于农业生物防治的优化培养

以具有防病促长且抑菌谱广的暹罗芽胞杆菌(Bacillus siamensis)FJAT-45551为出发菌株,分别以生物量和发酵液的青枯雷尔氏菌和尖孢镰刀菌抑菌活性为指标,通过单因子和正交试验对其培养基成分和发酵培养条件进行优化,从而提高其抑菌活性。结果表明,优化后的培养基配方为:麸皮20 g/L,蛋白胨25 g/L,MgSO_4·H_2O 0. 2 g/L,CaCl_20. 1 g/L,FeSO_4·7H_2O 0. 1 g/L,NaH_2PO_4·H_2O 0. 5 g/L,K_2HPO_40. 5 g/L;最适发酵培养条件为:接种量1%、摇床转速130 r/min、温度20℃、装液量50 mL(250 mL的摇瓶装液50 mL)、初始pH值为6. 0。在优化的发酵条件下,FJAT-45551发酵液对番茄青枯病菌(Ralstorinia solanacearum)FJAT-91的抑菌圈直径达30. 82 mm,较优化前的抑菌圈直径增加了9. 09 mm,抑菌活性提高了41. 83%。     

球衣菌合成聚羟基烷酸(PHA)的发酵研究

研究了球衣菌 (Sphaerotilussp.)W991 3 6合成聚羟基烷酸 (PHA)的培养基配方及发酵条件。结果表明 ,W991 3 6适宜发酵培养基配方为 :葡萄糖 1 0 2 5g/L ,蛋白胨 2 6 3g/L ,MgSO4·7H2 O 0 1 7g/L ,CaCl2 0 0 5g/L ,NaH2 PO4·2H2 O 0 0 2g/L ,K2 HPO40 0 4g/L ,KH2 PO40 0 3g/L ;最佳接种量为 0 1 3 8g (干 ) / 1 0 0mL ,培养基适宜初     

低糖流加法生产L-缬氨酸发酵工艺条件的研究

研究了糖浓度对L -缬氨酸产生菌 (Brevibacteriumflavum)Apv- 2菌积累L -缬氨酸的影响 ,通过三十吨发酵罐发酵工艺条件的试验 ,在合适的外界条件下 ,确定了该菌种发酵L -缬氨酸的最佳初糖浓度和补糖浓度 ,在初糖质量浓度为 3.5 %～ 4 .5 %时 ,发酵至 16h开始连续流加葡萄糖 ,维持发酵培养基中残糖质量浓度为 1.2 %～ 1.5 % ,经过 4 8h左右发酵 ,L -缬氨酸发酵产酸率 3.3%～ 3.5 %。     

鸟苷发酵的优化研究

以鸟苷产生菌_{Bacillussubtilis}AJ2 0 66为生产菌株 ,采用 5 0L自控发酵罐与摇瓶培养相结合的联动优化方法对鸟苷发酵进行了研究。谷氨酸钠对鸟苷发酵比较重要 ,培养基中加入 1 %的谷氨酸钠可使 5 0L罐最终产苷达 31 49g/L。次黄嘌呤 (Hx)作为前体可以直接用于鸟苷合成 ,发酵后期加入 0 2 %的Hx,可使 5 0L罐最终产苷达 33 2 4g/L。     

营养条件和流加发酵对放射型根瘤菌(Rhizobium radiobacter)产辅酶Q10的影响

利用放射型根瘤菌WSH2 6 0 1(RhizobiumradiobacterWSH2 6 0 1)重点考察了葡萄糖、蔗糖、玉米浆和蛋白胨、添加物以及流加发酵对细胞生长和产辅酶Q1 0 的影响 ,结果表明 ,葡萄糖和蔗糖适合于生产辅酶Q1 0 的最佳浓度分别为 30g L和 40g L ;辅酶Q1 0 发酵时玉米浆和蛋白胨的最适浓度分别为 11g L和 16g L ;添加蕃茄汁、玉米浆能提高发酵液的生物量 ,玉米浆、异戊醇、L 甲硫氨基酸等能促进辅酶Q1 0 的积累 ;与分批发酵相比 ,在 7L罐上流加蔗糖其细胞生物量 (DCW)和辅酶Q1 0 积累量增加 ,若在流加蔗糖的同时流加适当浓度的玉米浆能显著提高辅酶Q1 0 的产量 ,最大产量达到 5 2 .4mg L ;最大生物量 (DCW)和胞内辅酶Q1 0 含量 (C B值 )分别达到 2 6 .4g L和 2 .38mg g DCW ,比不流加的分批发酵分别提高 5 3 %和 33% ,比只流加蔗糖分别提高 2 4%和 2 6 %。     

一株凝结芽孢杆菌产生糖脂的工艺研究

对分离出的一株凝结芽孢杆菌生产糖脂的摇瓶发酵工艺进行了优化和 1 0L罐发酵实验。适宜发酵条件为 :培养基由 6 %豆油、 3 5g/LNaNO3、 0 75g/L酵母膏以及一定量的无机盐组成 ,发酵温度 3 0℃ ,初始pH8 5 ,搅拌转数 1 5 0～ 2 4 0r/min ,发酵周期 96h。糖脂产量达到 7 0 73g/L。     

细菌木聚糖酶高产菌的选育及发酵工艺研究

经筛选和诱变 ,选育出 1株产 β 木聚糖酶活力较高 ( 1 2 4.45IU/mL) ,而羧甲基纤维素酶活力较低( 1 .0 8IU/mL)的突变株L1 0 IGA。得出该菌产酶的最适发酵工艺为 1 .5 %半纤维素 ,0 .1 2 7%蛋白胨 ,0 .1 0 5 %K2 HPO4,0 .0 5 5 %MgSO4·7H2 O ,0 .45 %酵母膏 ,0 .2 2 5 %Twen40 ,装量 3 2 .5mL/1 5 0mL三角瓶 ,起始pH为 7.2 5 ,3 7℃发酵 48h后 45℃发酵 2 4h。     

拉曼被孢霉F5发酵生产γ-亚麻酸的研究

对拉曼被孢霉突变株F5发酵生产γ-亚麻酸的最适碳源、氮源、发酵时间及温度、无机盐离子添加、最适碳源浓度及补加碳源时间等发酵条件进行了研究探讨.最适发酵培养基组成为(g/L):葡萄糖100,酵母浸出粉4,蛋白胨1,K2HPO4 1,CaCl2 1×10-2,MgSO45×10-2,FeSO4 1×10-2,ZnSO4 7.5×10-3,CuSO4 0.5 × 10-5,MnSO4 2×10-3,pH 6.0.培养温度为25℃,140r/min振荡培养10天,培养8天后(即收获前2天)补加5%葡萄糖.发酵结果为:DC24.59g/L,TL 10.84g/L,TL/DC44.09%,GLA/TL10.67%,GLA产量为1156.63 mg/L. GLA产量较初始结果提高156.15%.该菌株已达到工业化生产菌株要求.     

Fuel ethanol from hardwood hemicellulose hydrolysate by genetically engineeredEscherichia coli B carrying genes fromZymomonas mobilis

Summary Escherichia coli B (ATCC 11303) carrying the PET operon on plasmid pLOI 297 converted hemicellulose hydrolysate to ethanol at an efficiency of 94% theoretical maximum, which is 15% better than the highest efficiency reported for pentose utilizing yeasts in a comparable system. Aspen prehydrolysate (APH), that had been produced by theBio-Hol Process using a Wenger extruder with SO₂ as catalyst, was used as feedstock. The fermentation medium contained predominantly xylose (35g/L) with acetic acid present at about 6g/L. With the pH controlled at 7.0, this concentration of acetic acid was not inhibitory for growth or xylose fermentation. When the APH was fortified with nutrients (tryptone and yeast extract), the recombinant (inoculated at 0.5 g dry wt/L) converted 100% of the xylose to ethanol with a volumetric productivity of 0.29 g/L/hr. Overliming the APH with Ca(OH)₂, followed by neutralization to pH 7 with sulphuric acid and removal of the insolubles, resulted in a 2-fold increase in productivity. The max. productivity was 0.76 g/L/hr. The productivity in Ca(OH)₂-treated APH, fortified with only mineral salts, was 0.26 g/L/hr.     

Pullulan production from synthetic medium by a new mutant of Aureobasidium pullulans

Pullulan with different molecular-weight could be applied in various fields. A UV-induced mutagenesis Aureobasidium pullulans UVMU6-1 was obtained from the strain A. pullulans CGMCC3.933 for the production of low-molecular-weight pullulan. First, the obtained polysaccharide from A. pullulans UVMU6-1 was purified and identified to be pullulan with thin-layer chromatography, Fourier transform infrared, and nuclear magnetic resonance. Then, culture medium and conditions for this strain were optimized by flask fermentation. Based on the optimized medium and culture conditions (pH 4, addition of 4?g/L Tween 80 for 96?hr of cultivation), continuously fermentation was performed. The highest pullulan production and dry biomass was 109 and 125?g/L after fermentation for 114?hr, respectively. The average productivity was about 1?g/L/hr, which was intensively higher than the previous reported. This study would lay foundations for the industrial production of pullulan.     

休哈塔假丝酵母HDYXHT-01利用木糖生产乙醇的发酵工艺优化

采用Plackett-Burman (PB) 方法和中心组合设计 (Ccentral composit design,CCD) 对休哈塔假丝酵母Candida shehataeHDYXHT-01利用木糖发酵生产乙醇的工艺进行优化。PB试验设计与分析结果表明：硫酸铵、磷酸二氢钾、酵母粉和接种量是影响木糖乙醇发酵的4个关键因素,以乙醇产量为响应目标,采用CCD和响应面分析法 (Response surface methodology,RSM),确定了木糖乙醇发酵的最佳工艺为：硫酸铵1.73 g/L、磷酸二氢钾3.56 g/L、酵母粉2.62 g/L和接种量5.66％,其他发酵条件为：木糖80 g/L,MgSO4·7H2O 0.1 g/L,pH 5.0,培养温度30 ℃,装液量100 mL/250 mL,摇床转速140 r/min,发酵时间48 h,在该条件下发酵液中乙醇产量可以达到26.18 g/L,比未优化前提高了1.15倍。     

一株拜氏梭菌利用甘蔗废糖蜜发酵生产丙酮丁醇

以甘蔗废糖蜜作为原料,利用Clostridium beijerinckii DSM 6422菌株进行丙酮丁醇发酵的初步研究.结果表明:采用H2SO4预处理糖蜜,初糖质量浓度60 g/L,(NH4)2SO4 2g/L,CaCO3 10 g/L,温度30℃,pH 5.5～7.0,接种量6％(体积分数),在5L发酵罐中发酵培养96 h,总溶剂产量为16.17 g/L,其中丁醇质量浓度为10.07 g/L,总溶剂产率为30.2％,糖利用率为89.3％.     

Control of feed rate to a fed-batch culture using a heat-flux sensor

Summary Substrate inhibition in batch fermentations can be avoided by employing the fed-batch technique in which substrate concentration is kept at low levels by a programmed feed rate. This research demonstrates the use of a heat-flux sensor to control substrate addition by continuously monitoring evolving heat which is proportional to fermentation rate. Batch fermentation with 240 g/L glucose in the medium was compared with a fed-batch starting with 20 g/L glucose in the medium and increased, with 500 g/L glucose, to a final equivalent glucose concentration of 240 g/L. The batch fermentation produced 106 g/L ethanol in 39 hr at 2.72 g/L/h, while the best fed-batch produced 114 g/L ethanol in 34 hr at 3.35 g/L/h with the same nutrients.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

圆红冬孢酵母菌发酵产油脂培养基及发酵条件的优化研究

采用均匀设计和单因子试验法,系统考察了圆红冬孢酵母菌(Rhodosporidiumtoruloides)在不同碳氮比条件下产油发酵情况以及添加无机盐对产油发酵的影响,通过均匀设计软件对二次多项回归方程求解及单因素分析得知在培养基组成分别为葡萄糖70g/L,硫酸铵0.1g/L,酵母粉0.75g/L,磷酸二氢钾0.4g/L,七水硫酸镁1.5g/L,初始pH6.0,在灭菌(121℃15min)后添加ZnSO41.91×10-6mmol/L、CaCl21.50mmol/L、MnCl21.22×10-4mmol/L、CuSO41.00×10-4mmol/L。发酵摇瓶装液量为250mL三角瓶装培养基50mL,接种量为10%(种龄28h)。在上述条件下,30℃振荡(200r/min)培养120h,所得菌体油脂含量高达76.1%,脂肪得率系数可达22.7。     

红曲多糖液态发酵工艺条件的优化

实验研究红曲多糖的液态发酵条件,得出优化后红曲菌ZKOA发酵工艺条件：蔗糖40g/L,酵母粉4．5g／L,KH2PO4·3H2O3．5∥L．MgSO40．4g／L,植物油2mL／L,接种量8％,种龄30h,发酵液起始pH5．0,发酵时间90h,在此条件下,摇瓶和中试发酵罐中的粗多糖质量浓度分别为7．6g／L和7．34g/L。     

海洋来源链霉菌MY0504产纤溶酶的发酵条件优化

【目的】以发酵液纤溶酶活力为指标,优化海洋来源的链霉菌菌株MY0504的发酵条件。【方法】在菌株生长曲线及单因素试验基础上,采用Plackett-Burman设计筛选影响纤溶酶活性的主要因素,进一步用最陡爬坡试验及Box-Behnken中心组合设计法优化发酵条件。【结果】纤溶酶活性最高的发酵条件为:葡萄糖21.68 g/L,酵母粉25.31 g/L,NaCl5.0 g/L,K_2HPO_4·3H_2O3.0 g/L,MgSO_4·7H_2O 0.5 g/L,FeSO_4·7H_2O 0.02 g/L,装液量50 mL(250 mL摇瓶),接种量10%(体积比),初始pH 7.5,温度24°C,转速200 r/min,培养时间4.5 d。发酵液纤溶酶活性可达2 190.6 U/mL。【结论】确定了MY0504菌株产纤溶酶的最优发酵条件,为该酶的进一步分离纯化及性质研究奠定基础。     

Breeding L-arginine-producing strains by a novel mutagenesis method: Atmospheric and room temperature plasma (ARTP)

A plasma jet, driven by an active helium atom supplied with an atmospheric and room temperature plasma (ARTP) biological breeding system, was used as a novel method to breed L-arginine high-yielding strains. A mutant with resistance to L-homoarginine and 8-azaguaine, ARG 3-15 (L-HA^r, 8-AG^r, L-His^-), was screened after several rounds of screening. The L-arginine production of these mutants was more than that of the original strain, increased by 43.79% for ARG 3-15. Moreover, N-acetyl-L-glutamate synthase activity of these mutants was also increased. After a series of passages, the hereditary properties of these mutants were found to be stable. Interestingly, beet molasses was utilized in a co-feeding fermentation and benefited to increase the productivity by 5.88%. Moreover, the fermentation with 1.0 g/L betaine could produce 9.33% more L-arginine than without betaine. In fed-batch fermentation, C. glutamicum ARG 3-15 began to produce L-arginine at the initial of logarithmic phase, and continuously increased over 24 hr to a final titer of 45.36 ± 0.42 g/L. The L-arginine productivity was 0.571 g/L/hr and the conversion of glucose (α) was 32.4% after 96 hr. These results indicated that C. glutamicum ARG 3-15 is a promising industrial producer.     

出芽短梗霉产聚苹果酸发酵条件的优化

【背景】出芽短梗霉可发酵葡萄糖生成聚苹果酸,但存在转化率和转化效率低等瓶颈,阻碍其实现商业化生产。【目的】通过优化发酵培养条件,提高出芽短梗霉的聚苹果酸产量、糖酸转化率和生产强度。【方法】采用单因素试验优化适宜出芽短梗霉BK-10菌株产生聚苹果酸的培养条件,通过Plackett-Burman法对培养基组分筛选显著性影响因素,并对其培养基中无机盐进行正交试验优化,最后进行5 L发酵罐验证。【结果】最优培养基配方和培养条件:100 g/L葡萄糖,1.5 g/L尿素,0.20 g/L KH_2PO_4,0.20 g/L ZnSO_4,0.05 g/L MgSO_4,0.75 g/L KCl,30 g/L CaCO_3,0.01%吐温-80,发酵温度26°C,250 mL摇瓶装液量50 mL。【结论】通过优化,聚苹果酸的糖酸转化率达到0.71 g/g,生产强度达到0.89 g/(L·h),较优化前分别提高了18.33%和71.15%,为发酵葡萄糖合成聚苹果酸进而生产L-苹果酸工艺的工业化生产奠定经济性基础。