Composite vegetable waste as renewable resource for bioelectricity generation through non-catalyzed open-air cathode microbial fuel cell

Single chambered mediatorless microbial fuel cell (MFC; non-catalyzed electrodes) was operated to evaluate the potential of bioelectricity generation from the treatment of composite waste vegetables (EWV) extract under anaerobic microenvironment using mixed consortia as anodic biocatalyst. The system was operated with designed synthetic wastewater (DSW; 0.98 kg COD/m³-day) during adaptation phase and later shifted to EWV and operated at three substrate load conditions (2.08, 1.39 and 0.70 kg COD/m³-day). Experimental data illustrated the feasibility of bioelectricity generation through the utilization of EWV as substrate in MFC. Higher power output (57.38 mW/m²) was observed especially at lower substrate load. The performance of MFC was characterized based on the polarization behavior, cell potentials, cyclic voltammetric analysis and sustainable resistance. MFC operation also documented to stabilize the waste by effective removal of COD (62.86%), carbohydrates (79.84%) and turbidity (55.12%).     

Purification and Some Properties of Milk Protease

Separation of acetic acid from palm oil mill effluent (POME) to increase its concentration by an anion exchange resin was examined as a preliminary study for its recovery from POME that had been anaerobically treated by sludge from a palm oil mill. This paper concerns the acetic acid thus separated for producing bacterial polyhydroxyalkanoate (PHA) by Alcaligenes eutrophus. It was found that sludge particles in POME strongly inhibited the adsorption of acetic acid on the anion exchange resin. Removing the sludge particles from the POME facilitated the separation of acetic acid from the POME efficiently. The concentrated acetic acid thus obtained from anaerobically treated POME could be used as a substrate in the fed-batch production of polyhydroxyalkanoate by Alcaligenes eutrophus.     

Electricity generation from the treatment of wastewater with a hybrid up‐flow microbial fuel cell

The performance of a prototype up‐flow single‐chambered microbial fuel cell (MFC) for electrical power generation using brewery wastewater as fuel is reported. The designed reactor consisted of three zones, namely a lower anaerobic digestion zone, a central MFC zone, and an upper effluent clarifier zone. Tests were conducted in batch mode using a beer wastewater as the fuel/electron donor (COD concentration: 430 mg/L) and mixed consortia (both sewage microflora and anaerobic sludge) as a source of electrogenic bacteria. A stable current density of ～2,270 mA/m² was generated under continuous polarization with a constant external resistance (0.01 kΩ) and cell polarization gave a peak power density of 330 mW/m² at a current density of 1,680 mA/m². Electrochemical impedance analysis showed that the overall internal resistance of the reactor was quite low, that is, 8.0 Ω. Cyclic voltammetric analysis of the anodic biofilm at low scan rate revealed quite complex processes at the anode, with three redox peaks, at potentials of 116, 214, and 319 mV (vs. NHE). Biotechnol. Bioeng. 2010;107: 52–58. © 2010 Wiley Periodicals, Inc.     

Electricity generation using p-nitrophenol as substrate in microbial fuel cell

The cell voltage and degradation rate of p-nitrophenol (PNP) were monitored in a two-chambered microbial fuel cell (MFC) system. Degradation metabolites in the anode solution of MFC were analyzed by gas chromatography–mass spectrometry (GC–MS). PNP was used as substrate by the MFC that was inoculated with anaerobic sludge. The results showed that electricity output increased with the PNP concentration increased, the MFC displayed a maximum power density of 1.778 mW m⁻² and a maximum PNP degradation rate of 64.69% when PNP was used as a sole substrate. However, the cell voltage and the PNP degradation rate with sodium acetate (402.3 mV and 95.96%) were higher than those fed with glucose (341.9 mV and 83.51%) when glucose and sodium acetate were used as a substrate, respectively. Furthermore, GC–MS analysis showed that the PNP was biodegraded completely after 142 h in the MFC. These results demonstrate that PNP can be used for electricity generation in MFC for practical applications of wastewater treatment.     

Functionally stable and phylogenetically diverse microbial enrichments from microbial fuel cells during wastewater treatment

Microbial fuel cells (MFCs) are devices that exploit microorganisms as biocatalysts to recover energy from organic matter in the form of electricity. One of the goals of MFC research is to develop the technology for cost-effective wastewater treatment. However, before practical MFC applications are implemented it is important to gain fundamental knowledge about long-term system performance, reproducibility, and the formation and maintenance of functionally-stable microbial communities. Here we report findings from a MFC operated for over 300 days using only primary clarifier effluent collected from a municipal wastewater treatment plant as the microbial resource and substrate. The system was operated in a repeat-batch mode, where the reactor solution was replaced once every two weeks with new primary effluent that consisted of different microbial and chemical compositions with every batch exchange. The turbidity of the primary clarifier effluent solution notably decreased, and 97% of biological oxygen demand (BOD) was removed after an 8-13 day residence time for each batch cycle. On average, the limiting current density was 1000 mA/m(2), the maximum power density was 13 mW/m(2), and coulombic efficiency was 25%. Interestingly, the electrochemical performance and BOD removal rates were very reproducible throughout MFC operation regardless of the sample variability associated with each wastewater exchange. While MFC performance was very reproducible, the phylogenetic analyses of anode-associated electricity-generating biofilms showed that the microbial populations temporally fluctuated and maintained a high biodiversity throughout the year-long experiment. These results suggest that MFC communities are both self-selecting and self-optimizing, thereby able to develop and maintain functional stability regardless of fluctuations in carbon source(s) and regular introduction of microbial competitors. These results contribute significantly toward the practical application of MFC systems for long-term wastewater treatment as well as demonstrating MFC technology as a useful device to enrich for functionally stable microbial populations.     

Olive mill wastewater treatment in single-chamber air-cathode microbial fuel cells

Olive mill wastewaters create significant environmental issues in olive-processing countries. One of the most hazardous groups of pollutants in these wastewaters is phenolic compounds. Here, olive mill wastewater was used as substrate and treated in single-chamber air-cathode microbial fuel cells. Olive mill wastewater yielded a maximum voltage of 381 mV on an external resistance of 1 kΩ. Notable decreases in the contents of 3,4-dihydroxybenzoic acid, tyrosol, gallic acid and p-coumaric acid were detected. Chemical oxygen demand removal rates were 65 % while removal of total phenolics by the process was lower (49 %). Microbial community analysis during the olive mill wastewater treating MFC has shown that both exoelectrogenic and phenol-degrading microorganisms have been enriched during the operation. Brevundimonas-, Sphingomonas- and Novosphingobium-related phylotypes were enriched on the anode biofilm, while Alphaproteobacteria and Bacteriodetes dominated the cathode biofilm. As one of the novel studies, it has been demonstrated that recalcitrant olive mill wastewaters could be treated and utilized for power generation in microbial fuel cells.     

Performance of microbial fuel cell with volatile fatty acids from food wastes

Food wastes were used as feedstock for the direct production of electricity in a microbial fuel cell (MFC). MFC operations with volatile fatty acids (VFA) produced 533 mV with a maximum power density of 240 mW/m². Short-chain VFAs, such as acetate, were degraded more rapidly and thus supported higher power generation than longer chain ones. In general, the co-existence of other, different VFAs slowed the removal of each VFA, which indicated that anodic microbes were competing for different substrates. 16S rRNA gene analysis using PCR-DGGE indicated that the MFC operation with VFAs had enriched unique microbial species.     

Electricity generation and modeling of microbial fuel cell from continuous beer brewery wastewater

Electricity production and modeling of microbial fuel cell (MFC) from continuous beer brewery wastewater was studied in this paper. A single air-cathode MFC was constructed, carbon fiber was used as anode and diluted brewery wastewater (COD = 626.58 mg/L) as substrate. The MFC displayed an open-circuit voltage of 0.578 V and a maximum power density of 9.52 W/m³ (264 mW/m²). Using the model based on polarization curve, various voltage losses were quantified. At current density of 1.79 A/m², reaction kinetic loss and mass transport loss both achieved to 0.248 V; while ohmic loss was 0.046 V. Results demonstrated that it was feasible and stable for producing bioelectricity from brewery wastewater; while the most important factors which influenced the performance of the MFC are reaction kinetic loss and mass transport loss.     

Evaluation of hydrolysis and fermentation rates in microbial fuel cells

This study determined the influence of substrate degradation on power generation in microbial fuel cells (MFCs) and microbial community selection on the anode. Air cathode MFCs were fed synthetic medium containing different substrates (acetate, glucose and starch) using primary clarifier sewage as source of electroactive bacteria. The complexity of the substrate affected the MFC performance both for power generation and COD removal. Power output decreased with an increase in substrate complexity from 99 ± 2 mW m⁻² for acetate to 4 ± 2 mW m⁻² for starch. The organic matter removal and coulombic efficiency (CE) of MFCs with acetate and glucose (82% of COD removal and 26% CE) were greater than MFCs using starch (60% of COD removal and 19% of CE). The combined hydrolysis–fermentation rate obtained (0.0024 h⁻¹) was considerably lower than the fermentation rate (0.018 h⁻¹), indicating that hydrolysis of complex compounds limits current output over fermentation. Statistical analysis of microbial community fingerprints, developed on the anode, showed that microbial communities were enriched according to the type of substrate used. Microbial communities producing high power outputs (fed acetate) clustered separately from bacterial communities producing low power outputs (fed complex compounds).     

Electricity generation in a membrane-less microbial fuel cell with down-flow feeding onto the cathode

A novel membrane-less microbial fuel cell (MFC) with down-flow feeding was constructed to generate electricity. Wastewater was fed directly onto the cathode which was horizontally installed in the upper part of the MFC. Oxygen could be utilized readily from the air. The concentration of dissolved oxygen in the influent wastewater had little effect on the power generation. A saturation-type relationship was observed between the initial COD and the power generation. The influent flow rate could affect greatly the power density. Fed by the synthetic glucose wastewater with a COD value of 3500 mg/L at a flow rate of 4.0 mL/min, the developed MFC could produce a maximum power density of 37.4 mW/m². Its applicability was further evaluated by the treatment of brewery wastewater. The system could be scaled up readily due to its simple configuration, easy operation and relatively high power density.     

Development of a solar-powered microbial fuel cell

Aims: To understand factors that impact solar‐powered electricity generation by Rhodobacter sphaeroides in a single‐chamber microbial fuel cell (MFC). Methods and Results: The MFC used submerged platinum‐coated carbon paper anodes and cathodes of the same material, in contact with atmospheric oxygen. Power was measured by monitoring voltage drop across an external resistance. Biohydrogen production and in situ hydrogen oxidation were identified as the main mechanisms for electron transfer to the MFC circuit. The nitrogen source affected MFC performance, with glutamate and nitrate‐enhancing power production over ammonium. Conclusions: Power generation depended on the nature of the nitrogen source and on the availability of light. With light, the maximum point power density was 790 mW m^?2 (2·9 W m^?3). In the dark, power output was less than 0·5 mW m^?2 (0·008 W m^?3). Also, sustainable electrochemical activity was possible in cultures that did not receive a nitrogen source. Significance and Impact of the Study: We show conditions at which solar energy can serve as an alternative energy source for MFC operation. Power densities obtained with these one‐chamber solar‐driven MFC were comparable with densities reported in nonphotosynthetic MFC and sustainable for longer times than with previous work on two‐chamber systems using photosynthetic bacteria.     

Continuous power generation and microbial community structure of the anode biofilms in a three-stage microbial fuel cell system

A mediator-less three-stage two-chamber microbial fuel cell (MFC) system was developed and operated continuously for more than 1.5 years to evaluate continuous power generation while treating artificial wastewater containing glucose (10 mM) concurrently. A stable power density of 28 W/m³ was attained with an anode hydraulic retention time of 4.5 h and phosphate buffer as the cathode electrolyte. An overall dissolved organic carbon removal ratio was about 85%, and coulombic efficiency was about 46% in this MFC system. We also analyzed the microbial community structure of anode biofilms in each MFC. Since the environment in each MFC was different due to passing on the products to the next MFC in series, the microbial community structure was different accordingly. The anode biofilm in the first MFC consisted mainly of bacteria belonging to the Gammaproteobacteria, identified as Aeromonas sp., while the Firmicutes dominated the anode biofilms in the second and third MFCs that were mainly fed with acetate. Cyclic voltammetric results supported the presence of a redox compound(s) associated with the anode biofilm matrix, rather than mobile (dissolved) forms, which could be responsible for the electron transfer to the anode. Scanning electron microscopy revealed that the anode biofilms were comprised of morphologically different cells that were firmly attached on the anode surface and interconnected each other with anchor-like filamentous appendages, which might support the results of cyclic voltammetry. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Effect of vitamins and cell constructions on the activity of microbial fuel cell battery

Construction of efficient performance of microbial fuel cells (MFCs) requires certain practical considerations. In the single chamber microbial fuel cell, there is no border between the anode and the cathode, thus the diffusion of the dissolved oxygen has a contrary effect on the anodic respiration and this leads to the inhibition of the direct electron transfer from the biofilm to the anodic surface. Here, a fed-batch single chambered microbial fuel cells are constructed with different distances 3 and 6?cm (anode- cathode spacing), while keeping the working volume is constant. The performance of each MFC is individually evaluated under the effects of vitamins & minerals with acetate as a fed load. The maximum open circuit potential during testing the 3 and 6?cm microbial fuel cells is about 946 and 791?mV respectively. By decreasing the distance between the anode and the cathode from 6 to 3?cm, the power density is decreased from 108.3?mW?m^?2 to 24.5?mW?m^?2. Thus, the short distance in membrane-less MFC weakened the cathode and inhibited the anodic respiration which affects the overall performance of the MFC efficiency. The system is displayed a maximum potential of 564 and 791?mV in absence & presence of vitamins respectively. Eventually, the overall functions of the acetate single chamber microbial fuel cell can be improved by the addition of vitamins & minerals and increasing the distance between the cathode and the anode.     

Influence of diligent disintegration on anaerobic biomass and performance of microbial fuel cell

Objectives

To enhance the performance of microbial fuel cells (MFC) by increasing the surface area of cathode and diligent mechanical disintegration of anaerobic biomass.

Results

Tannery effluent and anaerobic biomass were used. The increase in surface area of the cathode resulted in 78% COD removal, with the potential, current density, power density and coulombic efficiency of 675 mV, 147 mA m^?2, 33 mW m^?2 and 3.5%, respectively. The work coupled with increased surface area of the cathode with diligent mechanical disintegration of the biomass, led to a further increase in COD removal of 82% with the potential, current density, power density and coulombic efficiency of 748 mV, 229 mA m^?2, 78 mW m^?2 and 6% respectively.

Conclusions

Mechanical disintegration of the biomass along with increased surface area of cathode enhances power generation in vertical MFC reactors using tannery effluent as fuel.

     

Factors affecting current production in microbial fuel cells using different industrial wastewaters

This study evaluated how different types of industrial wastewaters (bakery, brewery, paper and dairy) affect the performance of identical microbial fuel cells (MFCs); and the microbial composition and electrochemistry of MFC anodes. MFCs fed with paper wastewater produced the highest current density (125 ± 2 mA/m²) at least five times higher than dairy (25 ± 1 mA/m²), brewery and bakery wastewaters (10 ± 1 mA/m²). Such high current production was independent of substrate degradability. A comprehensive study was conducted to determine the factor driving current production when using the paper effluent. The microbial composition of anodic biofilms differed according to the type of wastewater used, and only MFC anodes fed with paper wastewater showed redox activity at −134 ± 5 mV vs NHE. Electrochemical analysis of this redox activity indicated that anodic bacteria produced a putative electron shuttling compound that increased the electron transfer rate through diffusion, and as a result the overall MFC performance.     

Effects of inoculation strategy and cultivation approach on the performance of microbial fuel cell using marine sediment as bio-matrix

Aims: To investigate the effects of inoculation strategy and cultivation approach on the performance of microbial fuel cell (MFC). Methods and Results: A dual‐chamber sediment fuel cell was set up fed with glucose under batch condition. At day 30, the supernatant consortium was partly transferred and used as inoculum for the evaluation of cultivation approach. Power output gradually increased to 9·9 mW m^?2 over 180 days, corresponding to coulombic efficiency (CE) of 29·6%. Separated biofilms attached anode enabled power output and CE dramatically up to 100·9 mW m^?2 and over 50%, respectively, whereas the residual sediment catalysed MFC gave a poor performance. MFC catalysed by in situ supernatant consortium demonstrated more than twice higher power than MFC catalysed by the supernatant consortium after Fe(OH)₃ cultivation. However, the re‐generation of biofilms from the latter largely enhanced the cell performance. Conclusions: MFC exhibited a more efficient inducement of electroactive consortium than Fe(OH)₃ cultivation. MFC performance varied depending on different inoculation strategies. Significance and Impact of the Study: This is the first time to study cultivation approach affecting electricity generation. In addition, anodic limitations of mass and electron transfer were discussed through MFC catalysed by sediment‐based bio‐matrix.     

微生物燃料电池降解苯酚过程中微电场对阴极微生物多样性的影响

[背景]苯酚废水作为一种毒性强、难降解的废水而备受关注.目前,微生物燃料电池(microbial fuel cell,MFC)已经广泛用于苯酚废水的降解,MFC的产电效果和苯酚的降解效率与反应器内的微生物群落有着密切关系.[目的]为了提高MFC的产电效果及对有害物质的降解能力,需要对MFC中苯酚的降解和微生物群落结构进...     

Electricity generation and microbial community response to substrate changes in microbial fuel cell

The effect of substrate changes on the performance and microbial community of two-chamber microbial fuel cells (MFCs) was investigated in this study. The MFCs enriched with a single substrate (e.g., acetate, glucose, or butyrate) had different acclimatization capability to substrate changes. The MFC enriched with glucose showed rapid and higher power generation, when glucose was switched with acetate or butyrate. However, the MFC enriched with acetate needed a longer adaptation time for utilizing glucose. Microbial community was also changed when the substrate was changed. Clostridium and Bacilli of phylum Firmicutes were detected in acetate-enriched MFCs after switching to glucose. By contrast, Firmicutes completely disappeared and Geobacter-like species were specifically enriched in glucose-enriched MFCs after feeding acetate to the reactor. This study further suggests that the type of substrate fed to MFC is a very important parameter for reactor performance and microbial community, and significantly affects power generation in MFCs.     

Evaluation of procedures to acclimate a microbial fuel cell for electricity production

A microbial fuel cell (MFC) is a relatively new type of fixed film bioreactor for wastewater treatment, and the most effective methods for inoculation are not well understood. Various techniques to enrich electrochemically active bacteria on an electrode were therefore studied using anaerobic sewage sludge in a two-chambered MFC. With a porous carbon paper anode electrode, 8 mW/m² of power was generated within 50 h with a Coulombic efficiency (CE) of 40%. When an iron oxide-coated electrode was used, the power and the CE reached 30 mW/m² and 80%, respectively. A methanogen inhibitor (2-bromoethanesulfonate) increased the CE to 70%. Bacteria in sludge were enriched by serial transfer using a ferric iron medium, but when this enrichment was used in a MFC the power was lower (2 mW/m²) than that obtained with the original inoculum. By applying biofilm scraped from the anode of a working MFC to a new anode electrode, the maximum power was increased to 40 mW/m². When a second anode was introduced into an operating MFC the acclimation time was not reduced and the total power did not increase. These results suggest that these active inoculating techniques could increase the effectiveness of enrichment, and that start up is most successful when the biofilm is harvested from the anode of an existing MFC and applied to the new anode.     

Glycerol-fed microbial fuel cell with a co-culture of <Emphasis Type="Italic">Shewanella oneidensis</Emphasis> MR-1 and <Emphasis Type="Italic">Klebsiella pneumonae</Emphasis> J2B

Glycerol is an attractive feedstock for bioenergy and bioconversion processes but its use in microbial fuel cells (MFCs) for electrical energy recovery has not been investigated extensively. This study compared the glycerol uptake and electricity generation of a co-culture of Shewanella oneidensis MR-1 and Klebsiella pneumonia J2B in a MFC with that of a single species inoculated counterpart. Glycerol was metabolized successfully in the co-culture MFC (MFC-J&M) with simultaneous electricity production but it was not utilized in the MR-1 only MFC (MFC-M). A current density of 10 mA/m² was obtained while acidic byproducts (lactate and acetate) were consumed in the co-culture MFC, whereas they are accumulated in the J2B-only MFC (MFC-J). MR-1 was distributed mainly on the electrode in MFC-J&M, whereas most of the J2B was observed in the suspension in the MFC-J reactor, indicating that the co-culture of both strains provides an ecological driving force for glycerol utilization using the electrode as an electron acceptor. This suggests that a co-culture MFC can be applied to electrical energy recovery from glycerol, which was previously known as a refractory substrate in a bioelectrochemical system.