Zinc Chloride Methylene Blue, Ii. Preparation of Giesma and Wright Type Low Azure B Blood Stains from Dichromate Oxidized Commercial Dye

TO determine the amount of K₂Cr₂O₇ required to produce optimal Giemsa type staining, six 1 g amounts (corrected for dye content) of zinc methylene blue were oxidized with graded quantities of K₂Cr₂O₇ to produce 4, 8, 12, 16, 20 and 24% conversion of methylene blue to azure B. These were heated with a blank control 15 minutes at 100 C in 60-65 ml 0.4 N HCI. cooled, and adjusted to 50 ml to give 20 mg original dye/ml. Aliquots were then diluted to 1% and stains were made by the “Wet Giemsa” technic (Lillie and Donaldson 1979) using 6 ml 1% polychrome methylene blue, 4 ml 1% cosin (corrected for dye content), 2 ml 0.1 M pH 6.3 phosphate buffer, 5 ml acetone, and 23 ml distilled water. The main is added last and methanol fixed blood films are stained immediately for 20-40 min.

For methylene blue supplied by MCB 12-H-29, optimal stains were obtained with preparations containing 20 and 24% conversion of methylene blue to azure B. With methylene blue supplied by Aldrich (080787), 16% conversion of methylene blue to azure B was optimal. Eosinates prepared from a low azure B/methylene blue preparation selected in this way give good stains when used as a Wright stain in 0.3% methanol solution. However, when the 600 mg eosinate solution in glycerol methanol is supplemented with 160 mg of the same azure B/methylene blue chloride the mixture fails to perform well. The HCI precipitation of the chloride apparently produces the zinc methylene blue chloride salt which is poorly soluble in alcohol. It appears necessary to have a zinc-free azure B/methylene blue chloride to supplement the probably zinc-free eosinate used in the Giemsa mixture.     

Studies of Chromosome Banding with Giemsa in Vicia faba and Allium cepa

Giemsa dye is a complex mixture containing methylene blue, its oxidation products-azure Ⅰ, Ⅱ, Ⅲ, and their eosinate. The results of our experiments have demonstrated that staining with methylene blue alone can give a faint trace of banding as well as azure Ⅰ, Ⅱ. No bands are obtained with eosin. Nevertheless, good chromosome bandings can be often produced by staining with methylene blue-eosinate or azure Ⅱ-eosinate. These data indicate that eosinate has an important effect for the formation of C-banding on plant chromosomes. In our experiments, the treatments of chromosomes with trypsin or papain have also resulted in good C-banding pattern when slides are stained with Giemsa. We found that the slides untreated with proteinase showed homogeneous intense chromosome staining and, on the contrary, the slides treated with proteinase led to palestaining chromosomes and presenting bandings. It has shown that proteinase, especially trypsin, not only can remove a large amount of chromosomal protein but also can remove DNA and results in C-bandings. Treated properly with trypsin and followed by the Feulgen staining, chromosomes can also produce the C-bandings, but chromosomes treated overtime with trypsin are stained more palely in Feulgen reaction or lead to colourlessness. The above results have further proved that trypsin technique removes large amounts of chromosome DNA and removes less from the C-band regions than from the non-band regions. In this paper we mainly discussed the effects of protein on mechanism of plant chromosome banding. We consider that the production of plant C-banding is probably due to the differential accessibility of nucleoprotein between euehromatin and heteroehromatin regions. It brings about selective removal of nucleoprotein from the chromosome arms. We have compared the effect of trypsin with papain and pepsin on producing bands. Good bands are produced by Giemsa staining chromosomes with trypsin, but no bands are obtained by staining chromosomes treated with pepsin. So the results have expressed that histones are possibly playing more important role in C-bandings.     

ON THE NATURE OF THE DYE PENETRATING THE VACUOLE OF VALONIA FROM SOLUTIONS OF METHYLENE BLUE

When uninjured cells of Valonia are placed in methylene blue dissolved in sea water it is found, after 1 to 3 hours, that at pH 5.5 practically no dye penetrates, while at pH 9.5 more enters the vacuole. As the cells become injured more dye enters at pH 5.5, as well as at pH 9.5. No dye in reduced form is found in the sap of uninjured cells exposed from 1 to 3 hours to methylene blue in sea water at both pH values. When uninjured cells are placed in azure B solution, the rate of penetration of dye into the vacuole is found to increase with the rise in the pH value of the external dye solution. The partition coefficient of the dye between chloroform and sea water is higher at pH 9.5 than at pH 5.5 with both methylene blue and azure B. The color of the dye in chloroform absorbed from methylene blue or from azure B in sea water at pH 5.5 is blue, while it is reddish purple when absorbed from methylene blue and azure B at pH 9.5. Dry salt of methylene blue and azure B dissolved in chloroform appears blue. It is shown that chiefly azure B in form of free base is absorbed by chloroform from methylene blue or azure B dissolved in sea water at pH 9.5, but possibly a mixture of methylene blue and azure B in form of salt is absorbed from methylene blue at pH 5.5, and azure B in form of salt is absorbed from azure B in sea water at pH 5.5. Spectrophotometric analysis of the dye shows the following facts. 1. The dye which is absorbed by the cell wall from methylene blue solution is found to be chiefly methylene blue. 2. The dye which has penetrated from methylene blue solution into the vacuole of uninjured cells is found to be azure B or trimethyl thionine, a small amount of which may be present in a solution of methylene blue especially at a high pH value. 3. The dye which has penetrated from methylene blue solution into the vacuole of injured cells is either methylene blue or a mixture of methylene blue and azure B. 4. The dye which is absorbed by chloroform from methylene blue dissolved in sea water is also found to be azure B, when the pH value of the sea water is at 9.5, but it consists of azure B and to a less extent of methylene blue when the pH value is at 5.5. 5. Methylene blue employed for these experiments, when dissolved in sea water, in sap of Valonia, or in artificial sap, gives absorption maxima characteristic of methylene blue. Azure B found in the sap collected from the vacuole cannot be due to the transformation of methylene blue into this dye after methylene blue has penetrated into the vacuole from the external solution because no such transformation detectable by this method is found to take place within 3 hours after dissolving methylene blue in the sap of Valonia. These experiments indicate that the penetration of dye into the vacuole from methylene blue solution represents a diffusion of azure B in the form of free base. This result agrees with the theory that a basic dye penetrates the vacuole of living cells chiefly in the form of free base and only very slightly in the form of salt. But as soon as the cells are injured the methylene blue (in form of salt) enters the vacuole. It is suggested that these experiments do not show that methylene blue does not enter the protoplasm, but they point out the danger of basing any theoretical conclusion as to permeability on oxidation-reduction potential of living cells from experiments made or the penetration of dye from methylene blue solution into the vacuole, without determining the nature of the dye inside and outside the cell.     

Additional Schiff-Type Reagents for Use in Cytochemistry

Twenty-four new Schiff-type reagents were discovered in a survey of 140 different dyes. These dyes include acid fuchsin, acridine yellow, acriflavine hydrochloride, azure C., Bismarck brown R, Bismarck brown Y, celestine blue B, chrysoidine 3R, chrysoidine Y extra, cresyl violet, crystal violet, gentian violet, methylene blue, neutral violet, phenosafranin, phosphine GN, proflavine, toluidine blue O, and toluylene blue. Positive results obtained with crystal violet and a few samples of methylene blue are considered due to impurities. Various chemical extractions, aldehyde blocking reagents, and enzymatic treatments were used to verify the aldehyde specificity of the above dye-SO₂, reagents as well as azure A, brilliant cresyl blue, neutral red, safranin O, and thionin which have been mentioned by other workers. These reagents were tested in the Feulgen reaction for DNA and the PAS reaction for polysaccharides. Absorption curves were obtained from individual nuclei stained for DNA. The absorption peaks ranged from 450 mμ, to 630 mμ. depending on the dye studied. The Feulgen reaction could be followed by the PAS reaction or vice versa in mouse intestine using reactive dyes of complementary colors. The evidence indicates that a potential Schiff-type reagent must have at least one free NH₂ group on the dye molecule.     

The Azure Dyes their Purification and Physicochemical properties. II. Purification of Azure B

A method is described for the purification of the dye azure B in quantities sufficient for biological staining experiments on a larger scale. The method is based on the use of column chromatography. Two columns are employed. In column A with silica gel as adsorbent the azure B fraction is isolated from a suitable substrate ('technical' azure B gained by a modification of Bernthsen's synthesis of methylene blue, or plychrome methylene blue) using an acetate-formate mixture as eluent. In column B, on an Amberlite polyineric adsorbent (XAD-2) the acetate-formate anions are exchanged for chloride. Regeneration of both columns is possible: KMnO₄, Na₂S₂O₄ and water are run through column A, 5% NaOH, methanol and water through column B. Purification of azure B on economic terms is thus attained. The opinion is expressed that this method is also applicable to the purification of other cationic dyes.     

Zinc Chloride Methylene Blue. I. Biological Stain History, Physical Characteristics and Approximation of Azure B Content of Commercial Samples

Zinc chloride methylene blue appeared on the market almost contemporaneously with the zinc-free medicinal form. The former has rarely been reported as being used in blood stains. Recent suspension of manufacture of medicinal methylene blue by it. principal American producer has excited interest in the use of the zinc chloride form for the preparation of blood stains. According to Lillie (1944a,b) the azure B content of zinc chloride methylene blue may have varied from 5 to 30% in the samples studied. Taking the Merck Index (1968, 1976) figures for the spectroscopic absorption maximum (λmax) of 667.8 and 668 nm as standard, recent samples of zinc chloride methylene blue are calculated to contain 6-8% azure B. These figures are baaed on 1) the shift of λmax after exhaustive pH 9.5 chloroform extraction, 2) evaluation of the actual ratio of the observed TiCl₂ dye content to the theoretical for pure zinc chloride methylene blue, 3) comparison of spectroscopic and staining effects of graded hot dichromate oxidation products with those of highly purified azure B-methylene blue mixtures of known proportions.

As far as can be found, medicinal methylene blue is almost the exclusive source of cosin polychrome methylene blue blood stains. Lillie (1944c) included a short series comparing 5 zinc chloride methylene blues with a dozen medicinal methylene blue samples; all were oxidized with hot dichromate to produce successful Wright stains. No effort was made to remove the zinc Exhaustive pH 9.5 chloroform extraction of zinc chloride methylene blue (lot MCB 12-H-29) yielded a small amount of red dye which when extracted into 0.1 N HCI gave λmax = 650. The extraction moved the absorption peak of the zinc chloride methylene blue from 667 to 668 nm and the midpoint of the 90% maximum absorption band, 18 nm wide, from 666.5 to 667.5 nm.     

Phloxine-Methylene Blue Staining of Formalin-Fixed Tissue

It is at present difficult to obtain a good phloxine-metbylene blue stain on formalin-fixed tissue. When phloxine has been used, it is washed out in the process of staining with methylene blue and differentiating with colophony (rosin). In the original technic of Mallory, Zenker's fixation is used. The tissue is first stained with a 2.5% aqueous solution of phloxine, then with a solution of 1% methylene blue plus 1% azure II and differentiated in colophony.¹     

Reduced Methylene Blue as a Stain for Crustacean Nerves

Effective in situ staining of crustacean nerves was achieved with leuco methylene blue reduced with either ascorbic acid or sodium hydrosulfite (Na₂S₂O₄). A stock solution of methylene blue, 0.4% (ca. 0.001 M), and the reductants, ascorbic acid or sodium hydrosulfite (0.01 M), were prepared in van Harreveld's crayfish physiological solution. Methylene blue stock solution was mixed with either of the reductants in the approximate ratio of 1:10, v/v, and titrated to the end point. Ascorbic acid reduction is light catalyzed and requires intense illumination during titration. The cleared or leucomethylene blue stock solution is suitable for immediate use as a working nerve stain. With either reductant, the working solution oxidizes on standing in air, but can be titrated repeatedly without loss of staining properties. Dissected nerve trunks or tissue were immersed in the working stain for 20 min at room temperature and the staining process observed until suitable contrast developed. Excess dye was decanted and the tissues flooded with crayfish physiological solution. Contrast could sometimes be enhanced by flooding the stained area with 1% hydrogen peroxide in van Harreveld's solution. When permanent mounts were prepared, tissues were dehydrated with tertiary butyl alcohol in preference to ethyl alcohol series. For anatomical and neurophysiological studies of nerve distribution in crustaceans, the alternative use of either ascorbic acid or sodium hydrosulfite, as reductants for methylene blue, was preferable to the more complicated rongalit-technique and characterization of neural elements was fully as satisfactory.     

Romanowsky dyes and the Romanowsky-Giemsa effect. 3. Microspectrophotometric studies of Romanowsky-Giemsa staining. Spectroscopic evidence of a DNA-azure B-eosin Y complex producing the Romanowsky-Giemsa effect

The Romanowsky-Giemsa staining (RG staining) has been studied by means of microspectrophotometry using various staining conditions. As cell material we employed in our model experiments mouse fibroblasts, LM cells. They show a distinct Romanowsky-Giemsa staining pattern. The RG staining was performed with the chemical pure dye stuffs azure B and eosin Y. In addition we stained the cells separately with azure B or eosin Y. Staining parameters were pH value, dye concentration, staining time etc. Besides normal LM cells we also studied cells after RNA or DNA digestion. The spectra of the various cell species were measured with a self constructed microspectrophotometer by photon counting technique. The optical ray pass and the diagramm of electronics are briefly discussed. The nucleus of RG stained LM cells, pH congruent to 7, is purple, the cytoplasm blue. After DNA or RNA digestion the purple respectively blue coloration in the nucleus or the cytoplasm completely disappeares. Therefore DNA and RNA are the preferentially stained biological substrates. In the spectrum of RG stained nuclei, pH congruent to 7, three absorption bands are distinguishable: They are A1 (15400 cm-1, 649 nm), A2 (16800 cm-1, 595 nm) the absorption bands of DNA-bound monomers and dimers of azure B and RB (18100 cm-1, 552 nm) the distinct intense Romanowsky band. Our extensive experimental material shows clearly that RB is produced by a complex of DNA, higher polymers of azure B (degree of association p greater than 2) and eosin Y. The complex is primarily held together by electrostatic interaction: inding of polymer azure B cations to the polyanion DNA generates positively charged binding sites in the DNA-azure B complex which are subsequently occupied by eosin Y anions. It can be spectroscopically shown that the electronic states of the azure B polymers and the attached eosin Y interact. By this interaction the absorption of eosin Y is red shifted and of the azure B polymers blue shifted. The absorption bands of both molecular species overlap and generate the Romanowsky band. Its strong maximum at 18100 cm-1 is due to the eosin Y part of the DNA-azure B-eosin Y complex. The discussed red shift of the eosin Y absorption is the main reason for the purple coloration of RG stained nuclei. Using a special technique it was possible to prepare an artificial DNA-azure B-eosin Y complex with calf thymus DNA as a model nucleic acid and the two dye stuffs azure B and eosin Y.(ABSTRACT TRUNCATED AT 400 WORDS)     

Staining Rickettsiae in Yolk-Sac Cultures

Rickettsiae in yolk sacs are not stained well by the Macchiavello technique, and experiments were undertaken to understand the mechanisms involved. It was found that the citric acid destaining step was not effective and that most of the basic fuchsin was lost from the rickettsiae during the application of methylene blue, another basic dye. A staining technique was then evolved with carbol basic fuchsin in pH 7.45 phosphate buffer (0.4% dye, 0.4% phenol, 0.07 M buffer), followed directly by 0.8% aqueous malachite green oxalate. This technique worked well for R. mooseri, R. prowazeki, R. rickettsii, R. akari, and R. buretii, but for R. tsutsugumushi a modification was needed, whereby 4% aqueous Fe(NO₃)₃·9H₂O was used as destaining solution, and 0.5% aqueous fast green as the counter-stain.     

Lower azure B methylene blue ratios in Giemsa type blood and malaria stains

Starting from ancient reports that rare samples of methylene blue were apparently sufficiently contaminated with azures to give red plasmodial and red purple nuclear chromatin in Chenzinsky type methylene blue eosin stains, it was decided to determine how little azure B would suffice for such staining in methylene blue eosin stains. The traditional 1902 Giemsa had an azure : methylene blue : eosin ratio of about 6 : 3 : 6.3 : 10; Lillie's 1943 formula had a 5 : 7 : 10 ratio. In the current series of tests 5 : 7 : 10 (I), 4 : 8 : 10 (II), 3 : 9 : 10 (III), 2 : 10 : 10 (IV), 1 : 11 : 10 (V), and 0 : 12 : 10 (VI) were used. Malaria and blood stains were better than the standard 5 : 7 : 10 (I) in III, IV and II in that order. Normal and leukemic human blood, mouse blood with Plasmodium berghei, and monkey blood with the CDC strain of Pl. falciparum were used as test materials. The staining mixtures were made from highly purified samples of azure B and methylene blue. Staining mixtures contained 12 ml 0.1% thiazin dye, 10 ml 0.1% eosin, 2 ml each of glycerol, methanol and 0.1 M phosphate buffer pH 6.5, 3 ml acetone as accelerator, and distilled water to make 40 ml; staining times of 10--30 min were used.     

Investigation of Thiazin Dyes as Biological Stains I. The Staining Properties of Thionin and its Derivatives as Compared with Their Chemical Formulae

An investigation has been made of the staining properties of eight dyes of the thionin group. The dyes studied are as follows: tetra-ethyl thionin, asymmetrical di-ethyl thionin, tetra-methyl thionin (methylene blue), tri-methyl thionin (azure B), asymmetrical di-methyl thionin (azure A), symmetrical di-methyl thionin, mono-methyl thionin (azure C), and unsubstituted thionin. The staining properties were tested on sections of paraffin embedded material following five different methods of fixation. No counterstain was employed. It was shown that there was a general correlation between the extent of ethylation or methylation of the dyes and their staining properties. As one passes from tetra-ethyl thionin down the series to thionin itself, there is a progressive decrease in the amount of green showing in the preparations, and an increase in the amount of red present, also an increase in the metachromatic effects, and in the intensity of nuclear staining. There seems, also, to be a similar relation between staining qualities on the one hand and the color and solubility of the dye base on the other.     

Investigation of Thiazin Dyes as Biological Stains I. The Staining Properties of Thionin and its Derivatives as Compared with Their Chemical Formulae

An investigation has been made of the staining properties of eight dyes of the thionin group. The dyes studied are as follows: tetra-ethyl thionin, asymmetrical di-ethyl thionin, tetra-methyl thionin (methylene blue), tri-methyl thionin (azure B), asymmetrical di-methyl thionin (azure A), symmetrical di-methyl thionin, mono-methyl thionin (azure C), and unsubstituted thionin. The staining properties were tested on sections of paraffin embedded material following five different methods of fixation. No counterstain was employed. It was shown that there was a general correlation between the extent of ethylation or methylation of the dyes and their staining properties. As one passes from tetra-ethyl thionin down the series to thionin itself, there is a progressive decrease in the amount of green showing in the preparations, and an increase in the amount of red present, also an increase in the metachromatic effects, and in the intensity of nuclear staining. There seems, also, to be a similar relation between staining qualities on the one hand and the color and solubility of the dye base on the other.     

The purification of methylene blue and azure B by solvent extraction and crystallization.

Detailed schemes are described for the preparation of purified methylene blue and azure B from commercial samples of methylene blue. Purified methylene blue is obtained by extracting a solution of the commercial product in an aqueous buffer (pH 9.5) with carbon tetrachloride. Methylene blue remains in the aqueous layer but contaminating dyes pass into the carbon tetrachloride. Metal salt contaminants are removed when the dye is crystallized by the addition of hydrochloric acid at a final concentration of 0.25 N. Purified azure B is obtained by extracting a solution of commercial methylene blue in dilute aqueous sodium hydroxide (pH 11-11.5) with carbon tetrachloride. In this pH range, methylene blue is unstable and yields azure B. The latter passes into the carbon tetrachloride layer as it is formed. Metal salt contaminants remain in the aqueous layer. A concentrated solution oa azure B is obtained by extracting the carbon tetrachloride layer with 4.5 X 10(-4)N hydrobromic acid. The dye is then crystallized by increasing the hydrobromic acid concentration to 0.23 N. Thin-layer chromatography of the purified dyes shows that contamination with related thiazine dyes is absent or negligible. Ash analyses reveal that metal salt contamination is also negligible (sulphated ash less than 0.2%).     

A Simple and Rapid Staining Technique for Plastic Embedded Cartilage and Bone

In this report we describe a simple and rapid staining technique for cartilage and bone embedded in Araldite. Semitbin sections of embryonic vertebrae obtained from 15 to 17 day mouse fetuses were stained using an aqueous solution 0.25% with respect to methylene blue, 0.25% with respect to azure A, and 0.5% with respect to Na₂ CO₃, then counterstained with 1% aqueous pararosaniline chloride (MAP). Results were compared with toluidine blue stained sections. MAP permitted good discrimination of developmental stages of both cells and extracellular matrix within vertebral ossification centers during endochondral ossification. The technique is simple, rapid and applicable to plastic embedded sections, and can be used prior to ultrastructural examination.     

STUDIES ON PENETRATION OF DYES WITH GLASS ELECTRODE : V. WHY DOES AZURE B PENETRATE MORE READILY THAN METHYLENE BLUE OR CRYSTAL VIOLET?

Glass electrode measurements of the pH value of the sap of cells of Nitella show that azure B in the form of free base penetrates the vacuoles and raises the pH value of the sap to about the same degree as the free base of the dye added to the sap in vitro, but the dye salt dissolved in the sap does not alter the pH value of the sap. It is concluded that the dye penetrates the vacuoles chiefly in the form of free base and not as salt. The dye from methylene blue solution containing azure B free base as impurity penetrates and accumulates in the vacuole. This dye must be azure B in the form of free base, since it raises the pH value of the sap to about the same extent as the free base of azure B dissolved in the sap in vitro. The dye absorbed by the chloroform from methylene blue solution behaves like the dye penetrating the vacuole. These results confirm those of spectrophotometric analysis previously published. Crystal violet exists only in one form between pH 5 and pH 9.2, and does not alter the pH value of the sap at the concentrations used. It does not penetrate readily unless cells are injured. A theory of "multiple partition coefficients" is described which explains the mechanism of the behavior of living cells to these dyes. When the protoplasm is squeezed into the sap, the pH value of the mixture is higher than that of the pure sap. The behavior of such a mixture to the dye is very much like that of the sap except that with azure B and methylene blue the rise in the pH value of such a mixture is not so pronounced as with sap when the dye penetrates into the vacuoles. Spectrophotometric measurements show that the dye which penetrates from methylene blue solution has a primary absorption maximum at 653 to 655 mµ (i.e., is a mixture of azure B and methylene blue, with preponderance of azure B) whether we take the sap alone or the sap plus protoplasm. These results confirm those previously obtained with spectrophotometric measurements.     

The azure dyes: their purification and physicochemical properties. II. Purification of azure B.

A method is described for the purification of the dye azure B in quantities sufficient for biological staining experiments on a larger scale. The method is based on the use of column chromatography. Two columns are employed. In column A with silica gel as adsorbent the azure B fraction is isolated from a suitable substrate ('technical' azure B gained by a modification of Bernthsen's synthesis of methylene blue, or polychrome methylene blue) using an acetate-formate mixture as eluent. In column B, on an Amberlite polymeric adsorbent (XAD-2) the acetate-formate anions are exchanged in chloride. Regeneration of both columns is possible: KMnO4, Na2S2O4 and water are run through column A; 5% NaOH, methanol and water through column B. Purification of azure B on economic terms is thus attained. The opinion is expressed that this method is also applicable to the purification of other cationic dyes.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy.

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5-0.8 microm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8-10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5-0.8 µm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8-10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5–0.8 µm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8–10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.