Production of mannitol by Lactobacillus intermedius NRRL B-3693 in fed-batch and continuous cell-recycle fermentations

Improved fermentation processes were developed for the production of mannitol by a heterofermentative lactic acid bacterium (Lactobacillus intermedius NRRL B-3693). A fed-batch fermentation protocol overcame limitations caused by high substrate concentrations. The process was developed using corn steep liquor and glucose as inexpensive industrial nutrient sources, supplemented with a small amount of soy peptone and manganese. The fed-batch process resulted in a concentration of 176 ± 0.5 g mannitol from 184 ± 0 g fructose and 92 ± 0.1 g glucose per L of final fermentation broth in 30 h with a volumetric productivity of 5.9 g/(L h). Further increases in volumetric productivity of mannitol were obtained in a continuous cell-recycle fermentation process that reached more than 40 g/(L h), despite reduced mannitol levels of 78–98 g/L and residual substrate of 10–20 g/L. This is the first report of such a high volumetric productivity of mannitol by a heterofermentative lactic acid bacterium.     

High-rate continuous production of lactic acid by Lactobacillus rhamnosus in a two-stage membrane cell-recycle bioreactor

It is important to produce L(+)-lactic acid at the lowest cost possible for lactic acid to become a candidate monomer material for promising biodegradable polylactic acid. In an effort to develop a high-rate bioreactor that provides high productivity along with a high concentration of lactic acid, the performance of membrane cell-recycle bioreactor (MCRB) was investigated via experimental studies and simulation optimization. Due to greatly increased cell density, high lactic acid productivity, 21.6 g L(-1) h(-1), was obtained in the reactor. The lactic acid concentration, however, could not be increased higher than 83 g/L. When an additional continuous stirred tank reactor (CSTR) was attached next to the MCRB a higher lactic acid concentration of 87 g/L was produced at significant productivity expense. When the two MCRBs were connected in series, 92 g/L lactic acid could be produced with a productivity of 57 g L(-1) h(-1), the highest productivity among the reports of L(+)-lactic acid that obtained lactic acid concentration higher than 85 g/L using glucose substrate. Additionally, the investigation of lactic acid fermentation kinetics resulted in a successful model that represents the characteristics of lactic acid fermentation by Lactobacillus rhamnosus. The model was found to be applicable to most of the existing data with MCRBs and was in good agreement with Levenspiel's product-inhibition model, and the Luedeking-Piret equation for product-formation kinetics appeared to be effective in representing the fermentation kinetics. There was a distinctive difference in the production potential of cells (cell-density-related parameter in Luedeking-Piret equation) as lactic acid concentration increases over 55 g/L, and this finding led to a more precise estimation of bioreactor performance.     

Production of xylitol by recombinant Saccharomyces cerevisiae containing xylose reductase gene in repeated fed-batch and cell-recycle fermentations

Xylitol is a well-known sugar substitute with low-calorie and anti-cariogenic characteristics. An effort of biological production of xylitol from xylose was made in repeated fed-batch and cell-recycle fermentations of recombinant Saccharomyces cerevisiae BJ3505/δXR harboring the xylose reductase gene from Pichia stipitis. Batch fermentation with 20 g/l xylose and 18 g/l glucose resulted in 9.52 g/l dry cell mass, 20.1 g/l xylitol concentration and approximately 100% conversion yield. Repeated fed-batch operation to remove 10% of culture broth and to supplement an equal volume of 200 g/l xylose was designed to improve xylitol production. In spite of a sudden drop of cell concentration, an increase in dry cell mass led to high accumulation of xylitol at 48.7 g/l. To overcome loss of xylitol-producing biocatalysts in repeated fed-batch fermentation, cell-recycle equipment of hollow fiber membrane was implemented into a xylitol production system. Cell-recycle operation maintained concentration of the recombinant cells high inside a bioreactor. Final dry cell mass of 22.0 g/l, 116 g/l xylitol concentration, 2.34 g/l h overall xylitol productivity were obtained in cell-recycle fermentation supplemented with xylose and yeast extract solution, which were equivalent to 2.3-, 5.8- and 3.8-fold increases compared with the corresponding values of batch-type xylitol production parameters.     

Multi-stage high cell continuous fermentation for high productivity and titer

We carried out the first simulation on multi-stage continuous high cell density culture (MSC-HCDC) to show that the MSC-HCDC can achieve batch/fed-batch product titer with much higher productivity to the fed-batch productivity using published fermentation kinetics of lactic acid, penicillin and ethanol. The system under consideration consists of n-serially connected continuous stirred-tank reactors (CSTRs) with either hollow fiber cell recycling or cell immobilization for high cell-density culture. In each CSTR substrate supply and product removal are possible. Penicillin production is severely limited by glucose metabolite repression that requires multi-CSTR glucose feeding. An 8-stage C-HCDC lactic acid fermentation resulted in 212.9 g/L of titer and 10.6 g/L/h of productivity, corresponding to 101 and 429% of the comparable lactic acid fed-batch, respectively. The penicillin production model predicted 149% (0.085 g/L/h) of productivity in 8-stage C-HCDC with 40 g/L of cell density and 289% of productivity (0.165 g/L/h) in 7-stage C-HCDC with 60 g/L of cell density compared with referring batch cultivations. A 2-stage C-HCDC ethanol experimental run showed 107% titer and 257% productivity of the batch system having 88.8 g/L of titer and 3.7 g/L/h of productivity. MSC-HCDC can give much higher productivity than batch/fed-batch system, and yield a several percentage higher titer as well. The productivity ratio of MSC-HCDC over batch/fed-batch system is given as a multiplication of system dilution rate of MSC-HCDC and cycle time of batch/fed-batch system. We suggest MSC-HCDC as a new production platform for various fermentation products including monoclonal antibody.     

Fed-batch sorbose fermentation using pulse and multiple feeding strategies for productivity improvement

Microbial oxidation of D-sorbitol tol-sorbose byAcetobacter suboxydans is of commercial importance since it is the only biochemical process in vitamin C synthesis. The main bottleneck in the batch oxidation of sorbitol to sorbose is that the process is severely inhibited by sorbitol. Suitable fed-batch fermentation designs can eliminate the inherent substrate inhibition and improve sorbose productivity. Fed-batch sorbose fermentations were conducted by using two nutrient feeding strategies. For fed-batch fermentation with pulse feeding highly concentrated sorbitol (600 g/L) along with other nutrients were fed intermittently in four pulses of 0.5 liter in response to the increased DO signal. The fed-batch fermentation was over in 24 h with a sorbose productivity of 13.40 g/L/h and a final sorbose concentration of 320.48 g/L. On the other hand, in fed-batch fermentation with multiple feeds, two pulse feeds of 0.5 liter nutrient medium containing 600 g/L sorbitol was followed by the addition of 1.5 liter nutrient medium containing 600 g/L sorbitol at a constant feed rate of 0.36 L/h till the full working capacity of the reactor. The fermentation was completed in 24 h with an enhanced sorbose productivity of 15.09 g/L/h and a sorbose concentration of 332.60 g/L. The sorbose concentration and productivity obtained by multiple feeding of nutrients was found to be higher than that obtained by pulse feeding and was therefore a better strategy for fed-batch sorbose fermentation.     

Enhanced acetone-butanol fermentation using repeated fed-batch operation coupled with cell recycle by membrane and simultaneous removal of inhibitory products by adsorption

A novel acetone-butanol production process was developed which integrates a repeated fed-batch fermentation with continuous product removal and cell recycle. The inhibitory product concentrations of the fermentation by Clostridium acetobutylicum were reduced by the simultaneous extraction process using polyvinylpyridine (PVP) as an adsorbent. Because of the reduced inhibition effect, a higher specific cell growth rate and thus a higher product formation rate was achieved. The cell recycle using membrane separation increased the total cell mass density and, therefore, enhanced the reactor productivity. The repeated fed-batchoperation overcame the drawbacks typically associated with a batch operation such as down times, long lag period, and the limitation on the maximum initial substrate concentration allowed due to the substrate inhibition. Unlike a continuous operation, the repeated fed-batch operation could beoperated for a long time at a relatively higher substrate concentration without sacrificing the substrate loss in the effluent. As a result, the integrated process reached 47.2 g/L in the equivalent solvent concentration (including acetone, butanol, and ethanol) and 1.69 g/L . h in the fermentor productivity, on average, over a 239.5-h period. Compared with a controlled traditional batch acetone-butanol fermentation, the equivalent solvent concentration and the tormentor productivity were increased by 140% and 320%, respectively. (c) 1995 John Wiley & Sons Inc.     

Production of dextransucrase and dextran by Leuconostoc mesenteroides immobilized in calcium-alginate beads: II. Semicontinuous fed-batch fermentations

Cells of Leuconostoc mesenteroides immobilized in calcium alginate beads were used to produce dextransucrase (DS) in three sequential cycles of semicontinuous fed-batch fermentations. Each cycle consisted of a fed-batch DS production period of 24 h followed by a batch dextran production period for another 24 h. Free, suspended cells were used in only one cycle of fed-batch DS production followed by a dextran production period. It was impractically tedious to separate and reuse free cells. Increasing sucrose feed rate from 5 to 10 g/L h led to increases of the total enzymatic activity by about 88% with immobilized cells and by about 100% with free cells. In DS fed-batch semicontinuous fermentation, total enzymatic activity produced by immobilized cells was 1.35 and 1.56 times greater than that produced by free cells with respective sucrose feeding rates of 10 and 5 g/L h. These increases in enzyme productivity with immobilized cells, however, required total overall operating times three times longer (three cycles) than with free cells (one cycle). Growing the microorganism at optimum conditions for DS production also increased the dextran yield and shortened the time of conversion of sucrose to dextran, regardless of whether the cells were free or immobilized. Moreover, during three cycles of semicontinuous operation (144 h) immobilized cells produced more than three times as much dextran as free cells during one cycle (24 h).     

Acetone–butanol–ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 and in situ recovery by PDMS/ceramic composite membrane

PDMS/ceramic composite membrane was directly integrated with acetone-butanol-ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 at 37 °C and in situ removing ABE from fermentation broth. The membrane was integrated with batch fermentation, and approximately 46 % solvent was extracted. The solvent in permeates was 118 g/L, and solvent productivity was 0.303 g/(L/h), which was approximately 33 % higher compared with the batch fermentation without in situ recovery. The fed-batch fermentation with in situ recovery by pervaporation continued for more than 200 h, 61 % solvent was extracted, and the solvent in penetration was 96.2 g/L. The total flux ranged from 0.338 to 0.847 kg/(m(2)/h) and the separation factor of butanol ranged from 5.1 to 27.1 in this process. The membrane was fouled by the active fermentation broth, nevertheless the separation performances were partially recovered by offline membrane cleaning, and the solvent productivity was increased to 0.252 g/(L/h), which was 19 % higher compared with that in situ recovery process without membrane cleaning.     

Acetic Acid Production by an Electrodialysis Fermentation Method with a Computerized Control System

In acetic acid fermentation by Acetobacter aceti, the acetic acid produced inhibits the production of acetic acid by this microorganism. To alleviate this inhibitory effect, we developed an electrodialysis fermentation method such that acetic acid is continuously removed from the broth. The fermentation unit has a computerized system for the control of the pH and the concentration of ethanol in the fermentation broth. The electrodialysis fermentation system resulted in improved cell growth and higher productivity over an extended period; the productivity exceeded that from non-pH-controlled fermentation. During electrodialysis fermentation in our system, 97.6 g of acetic acid was produced from 86.0 g of ethanol; the amount of acetic acid was about 2.4 times greater than that produced by non-pH-controlled fermentation (40.1 g of acetic acid produced from 33.8 g of ethanol). Maximum productivity of electrodialysis fermentation in our system was 2.13 g/h, a rate which was 1.35 times higher than that of non-pH-controlled fermentation (1.58 g/h).     

Production of amyloglucosidase by Aspergillus niger under different cultivation regimens

Amyloglucosidase (AMG) was produced by Aspergillus niger in solid-state fermentation (SSF), submerged fermentation (SmF) and an aqueous, two-phase system of polyethyleneglycol (PEG) and salt. In SSF, a fed-batch mode of operation gave a yield of 64 U/ml compared with 44 U/ml in batch mode. Similar trends were observed for SmF, where fed-batch cultivation gave a yield of 102 U/ml compared with 66 U/ml in batch. Shorter cultivation times (66 h) were required for SmF than for SSF (96 h). In the aqueous, two-phase cultivation, the productivity and yield of AMG were both twice those in the control fermentation.M. Ramadas is with the Department of Biochemistry, Faculty of Medicine, University of Jaffna, Kokuvil, Sri Lanka. O. Holst and B. Mattiasson are with the Department of Biotechnology, Chemical Center, Lund University, Box 124, S-221 00 Lund, Sweden     

A novel membrane-integrated fermentation reactor system: application to pyruvic acid production in continuous culture by Torulopsis glabrata

This paper describes the performance of a novel bio-reactor system, the membrane-integrated fermentation reactor (MFR), for efficient continuous fermentation. The MFR, equipped with an autoclavable polyvinylidene difluoride membrane, has normally been used for biological wastewater treatment. The productivity of the MFR system, applied to the continuous production of pyruvic acid by the yeast Torulopsis glabrata, was remarkably high. The volumetric productivity of pyruvic acid increased up to 4.2 g/l/h, about four times higher than that of batch fermentation. Moreover, the membrane was able to filter fermentation broth for more than 300 h without fouling even though the cell density of the fermentation broth reached 600 as OD₆₆₀. Transmembrane pressure, used as an indicator of membrane fouling, remained below 5 kPa throughout the continuous fermentation. These results clearly indicate that the MFR system is a simple and highly efficient system that is applicable to the fermentative production of a range of biochemicals.     

On-line estimation of sugar concentration for control of fed-batch fermentation of lignocellulosic hydrolyzates by Saccharomyces cerevisiae

A feed control strategy, based on estimated sugar concentrations, was developed with the purpose of avoiding severe inhibition of the yeast Saccharomyces cerevisiae during fermentation of spruce hydrolyzate. The sum of the fermentable hexose sugars, glucose and mannose, was estimated from on-line measurements of carbon dioxide evolution rate and biomass concentration by use of a simple stoichiometric model. The feed rate of the hydrolyzate was controlled to maintain constant sugar concentration during fed-batch fermentation, and the effect of different set-point concentrations was investigated using both untreated and detoxified hydrolyzates. The fed-batch cultivations were evaluated with respect to cellular physiology in terms of the specific ethanol productivities, ethanol yields, and viability of the yeast. The simple stoichiometric model used resulted in a good agreement between estimated sugar concentrations and off-line determinations of sugar concentrations. Furthermore, the control strategy used made it possible to maintain a constant sugar concentration without major oscillations in the feed rate or the sugar concentration. For untreated hydrolyzates the average ethanol productivity could be increased by more than 130% compared to batch fermentation. The average ethanol productivity was increased from 0.12 to 0.28 g/g h. The productivity also increased for detoxified hydrolyzates, where an increase of 16% was found (from 0.50 to 0.58 g/g h).     

Production of poly(3-hydroxybutyrate) from whey by cell recycle fed-batch culture of recombinant Escherichia coli

A new fermentation strategy using cell recycle membrane system was developed for the efficient production of poly(3-hydroxybutyrate) (PHB) from whey by recombinant Escherichia coli strain CGSC 4401 harboring the Alcaligenes latus polyhydroxyalkanoate (PHA) biosynthesis genes. By cell recycle, fed-batch cultivation employing an external membrane module, the working volume of fermentation could be constantly maintained at 2.3 l. The final cell concentration, PHB concentration and PHB content of 194 g l^–1, 168 g l^–1 and 87%, respectively, were obtained in 36.5 h by the pH-stat cell recycle fed-batch culture using whey solution concentrated to contain 280 g lactose l^–1 as a feeding solution, resulting in a high productivity of 4.6 g PHB l^–1 h^–1.     

Indirect monitoring of acetate exhaustion and cell recycle improve lactate production by non-growing Escherichia coli

A two-phase, lactate fermentation by Escherichia coli ALS974 generates succinate and ethanol anaerobically from acetate. These by-products can be minimized by monitoring acetate concentration indirectly with dissolved O₂ (DO) during the initial aerobic cell-growth phase. Without DO monitoring, 3 g succinate/l and 1 g ethanol/l were generated while, with monitoring, less than 1 g succinate/l and no detectable ethanol were generated with 130 g lactate/l being produced. Furthermore, using a cell-recycle fermentation with ultrafiltration prolonged the anaerobic lactate production phase from 22 to 34 h, thereby achieving a lactate productivity of 4.2 g/l h, nearly 20% greater than the productivity of the fed-batch process.     

High-level production of ethanol during fed-batch ethanol fermentation with a controlled aeration rate and non-sterile glucose powder feeding of Saccharomyces cerevisiae

In this study, we utilized a unique strategy for fed-batch fermentation using ethanol-tolerant Saccharomyces cerevisiae to achieve a high-level of ethanol production that could be practically applied on an industrial scale. During this study, the aeration rate was controlled at 0.0, 0.13, 0.33, and 0.8 vvm to determine the optimal aeration conditions for the production of ethanol. Additionally, non-sterile glucose powder was fed during fed-batch ethanol fermentation and corn-steep liquor (CSL) in the medium was used as an organic N-source. When aeration was conducted, the ethanol production and productivity were superior to that when aeration was not conducted. Specifically, the maximum ethanol production reached approximately 160 g/L, when the fermentor was aerated at 0.13 vvm. These findings indicate that the use of a much less expensive C-source may enable the fermentation process to be directed towards the improvement of overall ethanol production and productivity in fermentors that are aerated at 0.13 vvm. Furthermore, if a repeated fed-batch process in which the withdrawal and fill is conducted prior to 36 h can be employed, aeration at a rate of 0.33 and/or 0.8 vvm may improve the overall ethanol productivity     

Citric acid production by Candida lipolytica Y 1095 in cell recycle and fed-batch fermentors

The effect of dissolved oxygen on citric acid production and oxygen uptake by Candida lipolytica Y 1095 was evaluated in cell recycle and fed-batch fermentation systems. The maximum observed volumetric productivity, which occurred at a dilution rate of 0.06 h(-1), a dissolved oxygen concentration of 80%, and a biomass concentration of 5% w/v, in the cell recycle system, was 1.32 g citric acid/L . h. At these same conditions, the citric acid yield was 0.65 g/g and the specific citric acid productivity was 24.9 mg citric acid/g cell . h. In the cell recycle system, citric acid yields ranged from 0.45 to 0.72 g/g. Both the volumetric and specific citric acid productivities were dependent on the dilution rate and the concentration of dissolved oxygen in the fermentor. Similar productivities (1.29 g citric acid/L . h) were obtained in the fed-batch system operated at a cycle time of 36 h, a dissolved oxygen concentration of 80%, and 60 g total biomass. Citric acid yields in the fed-batch fermentor were consistently lower than those obtained in the cell recycle system and ranged from 0.40 to 0.59 g/g. Although citric acid yields in the fed-batch fermentor were lower than those obtained in the cell recycle system, higher citric:isocitric acid ratios were obtained in the fed-batch fermentor. As in the cell recycle system, both the volumetric and specific citric acid productivities in the fed-batch fermentor were dependent on the cycle time and dissolved oxygen concentration. (c) 1995 John Wiley & Sons, Inc.     

High production of 1,3-propanediol from glycerol by Clostridium butyricum VPI 3266 in a simply controlled fed-batch system

Summary A simple fed-batch system which controls substrate feeding by measuring the CO₂ produced during the fermentation, was developped. This Fed-batch approach allowed high production of 1,3-propanediol from glycerol by Clostridium butyricum by avoiding substrate inhibition phenomena. 65 g/l of 1,3-propanediol was produced with a productivity of 1.21 g/l.h and a yield of 0.56. The concentration of 1,3-propanediol obtained and the productivity were significantly higher than those reached in batch culture.     

Extractive acidogenic fermentation by a supported liquid membrane

An on-line extractive fermentation system using a supported liquid membrane, recently termed pertractive fermentation, was investigated in order to overcome end-product inhibition and to enhance the productivity of microbial acidogenesis. It was observed that the pH of the fermentation broth was the key parameter for the successful operation of this pertractive fermentation system. At pH 4.8, 300 ml of broth and 80 sq·cm of extracting area, microbial activity in the system was prolonged and the productivity was enhanced about 5 fold compared to conventional acidogenic fermentation without extraction.     

Integrated production of lactic acid and biomass on distillery stillage

The possibilities of parallel lactic acid and biomass production in batch and fed-batch fermentation on distillery stillage from bioethanol production were studied. The highest lactic acid yield and productivity of 92.3 % and 1.49 g L^?1 h^?1 were achieved in batch fermentation with initial sugar concentration of 55 g L^?1. A significant improvement of the process was achieved in fed-batch fermentation where the concentration of lactic acid was increased to 47.6 % and volumetric productivity for 21 % over the batch process. A high number of Lactobacillus rhamnosus ATCC 7469 viable cells of 10⁹ CFU ml^?1 was attained at the end of fed-batch fermentation. The survival of 92.9 % of L. rhamnosus cells after 3 h of incubation at pH 2.5 validated that the fermentation media remained after lactic acid removal could be used as a biomass-enriched animal feed thus making an additional value to the process.     

Kinetics of inclusion body production in batch and high cell density fed-batch culture of Escherichia coli expressing ovine growth hormone.

A process for maximizing the volumetric productivity of recombinant ovine growth hormone (r-oGH) expressed in Escherichia coli during high cell density fermentation process has been devised. Kinetics of r-oGH expression as inclusion bodies and its effect on specific growth rates of E. coli cells were monitored during batch fermentation process. It was observed that during r-oGH expression in E. coli, the specific growth rate of the culture became an intrinsic property of the cells which reduced in a programmed manner upon induction. Nutrient feeding during protein expression phase of the fed-batch process was designed according to the reduction in specific growth rate of the culture. By feeding yeast extract along with glucose during fed-batch operation, high cell growth with very little accumulation of acetic acid was observed. Use of yeast extract helped in maintaining high specific cellular protein yield which resulted in high volumetric productivity of r-oGH. In 16 h of fed-batch fermentation, 3.2 g l-1 of r-oGH were produced at a cell OD of 124. This is the highest concentration of r-oGH reported to date using E. coli expression system. The volumetric productivity of r-oGH was 0.2 g l-1 h-1, which is also the highest value reported for any therapeutic protein using IPTG inducible expression system in a single stage fed-batch process.