Thermoset phenolic matrices reinforced with unmodified and surface-grafted furfuryl alcohol sugar cane bagasse and curaua fibers: properties of fibers and composites

Composites based on phenolic matrices and unmodified and chemically modified sugar cane bagasse and curaua fibers were prepared. The fibers were oxidized by chlorine dioxide, mainly phenolic syringyl and guaiacyl units of the lignin polymer, followed by grafting furfuryl alcohol (FA), which is a chemical obtained from a renewable source. The fibers were widely characterized by chemical composition analysis, crystallinity, UV-vis diffuse reflectance spectroscopy, SEM, DSC, TG, tensile strength, and 13C CP-MAS NMR. The composites were analyzed by SEM, impact strength, and DMA. The SEM images and DMA results showed that the oxidation of sugar cane bagasse fibers followed by reaction with FA favored the fiber/matrix interaction at the interface. The same chemical modification was less effective for curaua fibers, probably due to its lower lignin content, since the reaction considered touches mainly the lignin moiety. The tensile strength results obtained showed that the fibers were partially degraded by the chemical treatment, decreasing then the impact strength of the composites reinforced with them. In the continuity of the present project, efforts has been addressed to the optimization of fiber surface modification, looking for reagents preferably obtained from renewable resources and for chemical modifications that intensify the fiber/matrix interaction without loss of mechanical properties.     

Effects of iron,copper, and chromate ions on the oxidative degradation of cellulose model compounds

Iron(II) and iron(III) ions promote the degradation of the cellulose model 1,5-anhydrocellobiitol by oxygen or hydrogen peroxide; copper and chromate ions have marked and different effects on the iron catalysis. With starch, iron promotes the hydrogen peroxide-induced reaction and copper and chromate ions further enhance the reaction rate. The tensile strength of paper board is reduced by the action of hydrogen peroxide and iron(II) salts, and mixtures of copper, chromate, and arsenate salts (CCA, a timber preservative) also promote degradation in the presence or absence of iron ions. The oxidation of 1,5-anhydrocellobiitol by oxygen in the presence of iron ions is strongly inhibited by CCA and by cetyltrimethylammonium chloride, and is accelerated by phenols and related compounds.     

Viscoelastic properties and antimicrobial activity of cellulose fiber sheets impregnated with Ag nanoparticles

A silver nanoparticle colloid was prepared by a modified Tollens method using d-glucose as the reduction agent. The obtained nanoparticles were used for the modification of pine, linter and recycled cellulose fibers. Although the silver contents were relatively low (0.05-0.13wt.%), the cellulose-sheets prepared from the modified fibers show improved mechanical and viscoelastic properties. The tensile index (strength) increased with up to 30% in comparison to the index of the sheets obtained from the untreated fibers. The influence of the nanoparticles on the viscoelastic properties of the cellulose sheets was investigated by dynamic mechanical analysis (DMA) in the temperature range from -120 to 20°C and with a force frequency of 100Hz. A broad relaxation transition positioned at -80°C was observed in the loss modulus spectrum of all the cellulose sheets, while the Ag-modified sheets exhibited higher storage moduli values in the whole temperature range. The antimicrobial activity tests show that the pine, silver and recycled cellulose fiber sheets with silver nanoparticles can be successfully employed to prevent the viability and growth of the common pathogens Staphylococcus aureus, Escherichia coli and Candida albicans.     

Modification of high lignin content kraft pulps with laccase to improve paper strength properties. 1. Laccase treatment in the presence of gallic acid

Laccase was reacted with gallic acid in the presence of a high-kappa (91) kraft pulp. The result was a modified pulp with 34%, 20%, and 72% improvements in burst, tensile, and wet tensile strength compared to untreated control samples. Fully bleached pulps were not responsive to the laccase treatment, indicating lignin was the major target for the fiber modification. The results indicate that the strength increases were a combined effect of improvements of hydrogen bonding between fibers and creation of phenoxy radical cross-links within the sheet.     

Structure of a new tetranuclear iron(III) complex with an oxo-bridge; factors to govern formation and stability of oxo-bridged iron(III) species in the L-subunit of ferritin

We have investigated the reaction products of several iron(III) compounds with hydrogen peroxide, and have found that hydrogen peroxide promotes the formation of an oxo-bridged iron(III) species in the presence of methanol (electron donor), and carboxyl groups of the ligand systems play a role to give the tetranuclear iron(III) compound containing a bent Fe-O-Fe unit (O: oxo oxygen atom). Based on the present results and the facts that L-chains of human ferritins lack ferroxidase activity, but are richer in carboxyl groups (glutamates) exposed on the cavity surface, it seems reasonable to conclude that (i) the hydrogen peroxide released in the H-subunit may contribute to the formation of a diferric oxo-hydrate in the L-subunit, (ii) the formation of a bent oxo-bridged iron(III) species is essentially important in the L-subunit, and (iii) rich carboxyl groups in L-subunits contribute to facilitate iron nucleation and mineralization through the capture and activation of the peroxide ion, and formation of a stable bent oxo-bridged iron(III) species.     

Modification of high-lignin softwood kraft pulp with laccase and amino acids

This study demonstrates the potential of laccase-facilitated grafting of amino acids to high-lignin content pulps to improve their physical properties in paper products. Research studies have recently reported that increases in anionic fiber charge can improve strength properties of paper. In an effort to increase carboxylic acid groups, we developed a unique two-stage laccase grafting protocol in which fibers were initially treated with laccase followed by grafting reactions with amino acids. The bulk acid group content was measured, and a variety of amino acids including glycine (Gly), phenylalanine (Phe), serine (Ser), arginine (Arg), histidine (His), alanine (Ala), and aspartic acid (Asp) were examined. The effects of optimizing laccase dose, and amino acid structures, on fiber modification chemistry were studied. Histidine provided the best yield of acid groups on pulp fiber, and was used for the preparation of handsheets for physical strength testing. Laccase-histidine treated pulp showed an increase in strength properties of the resulting paper.     

New Enzyme-based Process Direction to Prevent Wool Shrinking without Substantial Tensile Strength Loss

In this paper a new enzymatic process direction is described for obtaining machine washable wool with acceptable quality. In general, application of protease enzyme technology in wool processing results in considerable loss of tensile strength by diffusion of the enzyme into the interior of wool fibers. To overcome this disadvantage enzymatic activity has been more targeted to the outer surface of the scales by improving the susceptibility of the outer surface scale protein for proteolytic degradation. This has been realized by a pretreatment of wool with hydrogen peroxide at alkaline pH in the presence of high concentrations of salt.     

On the anisotropy of the canine diaphragmatic central tendon

We studied the mechanical and anatomical anisotropy of the canine diaphragmatic central tendon (CT). Dumb-bell-shaped strips with effective dimensions of 10 x 2 mm (length x width) were cut from different regions of the canine diaphragmatic CT in two different orientations relative to the direction of neighboring muscle fibers. Specimens sampled with their long axial dimension oriented parallel to the neighboring muscle fibers were named Group-1 and those sampled with an orientation perpendicular to the neighboring muscle fibers were named Group-2. Results from one-dimensional stress-strain and tensile failure strength tests revealed that the CT is a nonlinear, inelastic, and anisotropic material. Group-1 specimens were found to have a higher stiffness, higher failure strength and higher strain energy density at failure than Group-2 specimens. Polarized microscopy showed that multiple sheets of collagen fiber bundles formed an orthogonal network in the tendon. Collagen fiber bundles along Group-1 direction formed parallel trajectory lines connecting the neighboring costal and crural muscles; bundles along Group-2 direction were observed to orient 90 degrees away. At the central apex region of the CT, collagen bundles of Group-1 formed a fan-like trajectory pattern. This collagen network architecture was compared favorably to the trajectories of an approximated principal stress field in the CT due to simulated contractile forces from its adjacent costal and crural muscles. These combined results suggest a structure-function relationship for the anatomical and mechanical anisotropy in the canine diaphragmatic CT.     

Properties and potential medical applications of regenerated casein fibers crosslinked with citric acid

Regenerated protein fibers developed from casein using alkaline solutions and crosslinked with citric acid have good tensile properties and water stability but were cytotoxic. Casein is obtained as a byproduct during skim milk production but has limited industrial applications. In this research, casein was dissolved using alkaline solutions and the effects of fiber formation conditions on the tensile properties was studied before and after crosslinking with citric acid. Crosslinked casein fibers had tensile strength as high as 110 MPa and breaking elongation of 13.6%. The fibers were also stable in 90°C water between pH 3 and 9 but were hydrolyzed at pH 11. Casein was cytotoxic and did not support the attachment and growth of mouse fibroblasts.     

Cytochrome c-catalyzed membrane lipid peroxidation by hydrogen peroxide.

Cytochrome c(3+)-catalyzed peroxidation of phosphatidylcholine liposomes by hydrogen peroxide (H2O2) was indicated by the production of thiobarbituric acid reactive substances, oxygen consumption, and emission of spontaneous chemiluminescence. The iron chelator diethylenetriaminepentaacetic acid (DTPA) only partially inhibited peroxidation when H2O2 concentrations were 200 microM or greater. In contrast, iron compounds such as ferric chloride, potassium ferricyanide, and hemin induced H2O2-dependent lipid peroxidation which was totally inhibitable by DTPA. Cyanide and urate, which react at or near the cytochrome-heme, completely prevented lipid peroxidation, while hydroxyl radical scavengers and superoxide dismutase had very little or no inhibitory effect. Changes in liposome surface charge did not influence cytochrome c3+ plus H2O2-dependent peroxidation, but a net negative charge was critical in favoring cytochrome c(3+)-dependent, H2O2-independent lipid auto-oxidative processes. These results show that reaction of cytochrome c with H2O2 promotes membrane oxidation by more than one chemical mechanism, including formation of high oxidation states of iron at the cytochrome-heme and also by heme iron release at higher H2O2 concentrations. Cytochrome c3+ could react with mitochondrial H2O2 to yield "site-specific" mitochondrial membrane lipid peroxidation during tissue oxidant stress.     

Preparation and properties of alginate/carboxymethyl chitosan blend fibers

Alginate/carboxymethyl chitosan blend fibers, prepared by spinning their mixture solution through a viscose-type spinneret into a coagulating bath containing aqueous CaCl₂, were studied for structure and properties with the aid of infrared spectroscopy (IR), X-ray diffraction (XRD) and scanning electron micrography (SEM). The analyses indicated a good miscibility between alginate and carboxymethyl chitosan, because of the strong interaction from the intermolecular hydrogen bonds. The best values of the dry tensile strength and breaking elongation were obtained when carboxymethyl chitosan content was 30 and 10 wt%, respectively. The wet tensile strength and breaking elongation decreased with the increase of carboxymethyl chitosan content. Introduction of CM-chitosan in the blend fiber improved water-retention properties of blend fiber compared to pure alginate fiber. Antibacterial fibers, obtained by treating the fibres with aqueous solution of N-(2-hydroxy)-propyl-3-trimethylammonium chitosan chloride and silver nitrate, respectively, exhibited good antibacterial activity to Staphylococcus aureus.     

Surface modification of natural fibers using bacteria: depositing bacterial cellulose onto natural fibers to create hierarchical fiber reinforced nanocomposites

Triggered biodegradable composites made entirely from renewable resources are urgently sought after to improve material recyclability or be able to divert materials from waste streams. Many biobased polymers and natural fibers usually display poor interfacial adhesion when combined in a composite material. Here we propose a way to modify the surfaces of natural fibers by utilizing bacteria ( Acetobacter xylinum) to deposit nanosized bacterial cellulose around natural fibers, which enhances their adhesion to renewable polymers. This paper describes the process of modifying large quantities of natural fibers with bacterial cellulose through their use as substrates for bacteria during fermentation. The modified fibers were characterized by scanning electron microscopy, single fiber tensile tests, X-ray photoelectron spectroscopy, and inverse gas chromatography to determine their surface and mechanical properties. The practical adhesion between the modified fibers and the renewable polymers cellulose acetate butyrate and poly(L-lactic acid) was quantified using the single fiber pullout test.     

Free Radical Generation at the Solid/Liquid Interface in Iron Containing Minerals

The potential for free radical release has been measured by means of the spin trapping technique on three kinds of iron containing particulate: two asbestos fibers (chrysotile and crocidolite); an iron-exchanged zeolite and two iron oxides (magnetite and haematite). DMPO (5,5'-dimethyl-1 -pirroline-N-oxide), used as spin trap in aqueous suspensions of the solids, reveals the presence of the hydroxyl and carboxylate radicals giving rise respectively to the two adducts [DMPO-OH] and [DMPO-CO2], each characterized by a well-defined EPR spectrum. Two target molecules have been considered: the formate ion to evidence potential for hydrogen abstraction in any biological compartment and hydrogen peroxide, always present in the phagosome during phagocytosis. The kinetics of decomposition of hydrogen peroxide has also been measured on all solids. Ferrozine and desferrioxamine, specific chelators of Fe(II) and Fe(III) respectively, have been used to remove selectively iron ions. Iron is implicated in free radical release but the amount of iron at the surface is unrelated to the amount of radicals formed. Only few surface ions in a particular redox and coordination state are active. Three different kinds of sites have been evidenced: one acting as H abstractor, the other as a heterogeneous catalyst for hydroxyl radical release, the third one related to catalysis of hydrogen peroxide disproportionation. In both mechanisms of free radical release, the Fe-exchanged zeolite mimics the behaviour of asbestos whereas the two oxides are mostly inert. Conversely magnetite turns out to be an excellent catalyst for hydrogen peroxide disproportionation while haematite is inactive also in this reaction. The results agree with the implication of a radicalic mechanism in the in vitro DNA damage and in the in vivo toxicity of asbestos.     

Durability of lignocellulosic fibers treated with vegetable oil–phenolic resin

Jute and sisal fibers were treated with an aqueous emulsion of neem oil and phenolic resin at elevated temperature for enhancing their tensile strength, hydrophobicity and resistance against biological and chemical degradations. The process was found to lead to the transesterification of cellulose chain hydroxyl groups and increased crystallinity. Treatment efficacy was evaluated by characterizing fibers by exposing them to biological and chemical degradations. The results indicate that the short-term tensile strength increased by 61–75% following treatment. After biodegradation, treated fibers were found to retain 63–70% of their initial tensile strength, while untreated fibers retained 28–32%. Treated fibers retained 52–60% of tensile strength after 90-day exposure to 3% salinity and 48–55% of tensile strength after similar exposure to pH between 3 and 10. For untreated fibers the corresponding figures were 9–13% and 10–12% respectively.     

不同纤维桩表面处理方式对牙根修复后抗折裂强度的影响

目的:探讨不同纤维桩表面处理方式对牙根修复后抗折裂强度的影响。方法:收集行正畸拔除的前磨牙120颗作为本研究样本,随机将120个纤维桩分为对照组、喷砂组和过氧化氢酸蚀组,每组40例。对照组纤维桩表明不给予任何处理,喷砂组给予氧化铝砂粒持续喷砂粗化处理,过氧化氢酸蚀组给予10%过氧化氢溶液处理,均包埋于纤维桩道预备好的离体牙内,采用相同树脂制备成核,行全冠修复与黏固,再模拟口腔内部环境给予样本牙冷热循环处理,经相同环境加载后,置于电子万能实验机获取样本牙抗折裂强度数据。对比三组离体牙样本体型数据、离体牙断裂方式、抗折裂强度,对三组进行为期24个月的定期随访,统计三组修复体断裂率,并采用Kaplan-Meier曲线和Log Rank法分析三组的生存状况。结果:三组的离体牙样本关于牙齿长度、牙根长度、颈部颊舌径及颈部近远中径对比差异无统计学意义(P0.05);喷砂组和过氧化氢酸蚀组的离体牙抗折裂强度显著强于对照组(P0.05);喷砂组和过氧化氢酸蚀组的牙齿折裂总发生率分别为20.00%和22.50%,均显著低于对照组的70.00%(P0.05)。但两组间比较差异无统计学意义(P0.05)。喷砂组、过氧化氢酸蚀组的生存状况显著优于对照组。结论:前磨牙修复过程中,对纤维桩表面进行喷砂或过氧化氢酸蚀处理均能提高牙根修复后抗折裂强度,改善修复体修复效果生存状况,且两种纤维桩表面处理方式对离体牙样本的断裂方式和抗折裂强度影响相当。     

Mechanism of surface peptide proton exchange in bovine pancreatic trypsin inhibitor. Salt effects and O-protonation

The acid-catalyzed hydrogen exchange rate constants kH, and the base-catalyzed rate constants kOH, have been determined (in the preceding paper) for the 25 most rapidly exchanging NH groups of bovine pancreatic trypsin inhibitor. Most of these NH groups are at the protein-solvent interface. The correlation of kH, but not kOH, with the static accessibility and hydrogen bonding of the peptide carbonyl O atom indicates that the mechanism of acid catalysis in proteins involves O-protonation. Agreement between the ionic strength dependence observed for kH and kOH and the ionic strength dependence calculated for an O-protonation mechanism supports this conclusion. N-protonation for acid catalysis, as well as N-deprotonation for base catalysis, have traditionally been assumed in the mechanism of the chemical step in peptide amide proton exchange. A preference for the alternative O-protonation mechanism has far-reaching implications in the interpretation of protein hydrogen exchange kinetics. With an O-protonation mechanism, acid-catalyzed rates of surface NH groups are primarily a function of the average solvent accessibility of the carbonyl O atoms in the dynamic solution structure, while base-catalyzed rates of surface NH groups measure solvent accessibility of the peptide N. The relative dynamic accessibilities of peptide O atoms, as measured by relative values of kH (corrected for electrostatic effects), correlate with O static accessibilities in the crystal structure. A lower correlation of static accessibility of N atoms with kOH is observed for surface NH groups in peptide groups in which the carbonyl O is not hydrogen bonded. For some surface NH groups, the observed pH of minimum rate, pHmin, deviates widely from the pHmin of model compounds. This is explained as the combined result of electrostatic effects and of the differences in accessibility of the carbonyl O and N atoms that result in a change in the relative values of kH and kOH as compared to those of model peptides. A mechanism whereby exchange of interior sites is catalyzed by interactions of catalysis ions with protein surface atoms via charge transfer is suggested.     

Wet strength improvement of unbleached kraft pulp through laccase catalyzed oxidation

Previous investigations have shown that laccase catalyzed oxidation of lignin containing wood fibers can enhance the strength of medium density fiberboards. In the present work it was investigated if laccase treatment had any impact on the tensile strength of a high yield unbleached kraft pulp. Treatment with laccase alone had only a very little effect on the wet strength of the pulp, whereas addition of lignin rich extractives increased the wet strength after the enzyme treatment significantly. A mediated oxidation gave a similar improvement of the wet tensile strength although no lignin was added to the fiber suspension. Furthermore, it was found that a heat treatment combined with a mediated oxidation gave a higher improvement in wet tensile strength than could be accounted for by the individual treatments. No change in dry tensile strength from the laccase treatment was observed. It is suggested that the observed improvement in wet tensile strength is related to polymerization of lignin on fibers in the hand sheet and/or coupling of phenoxy radicals on lignin associated to adjacent fibers. For the different mediators studied, a correlation was found between oxygen consumption upon mediated oxidation and generation of wet strength in the pulp.     

Some properties of alginate gels derived from algal sodium alginate

Alginic acid in soluble sodium alginate turns to insoluble gel after contact with divalent metal ions, such as calcium ions. The sodium alginate character has an effect on the alginate gel properties. In order to prepare a suitable calcium alginate gel for use in seawater, the effects of sodium alginate viscosity and M/G ratio (the ratio of D-mannuronate to L-guluronate) on the gel strength were investigated. The wet tensile strengths of gel fibers derived from high viscosity sodium alginate were higher than those from low viscosity sodium alginate. The tensile strength increased with diminishing sodium alginate M/G ratio. Among the gel fibers tested, the gel fiber obtained from a sodium alginate I-5G (1% aqueous solution viscosity = 520 mPa·s, M/G ratio = 0.6) had the highest wet tensile strength. After 13 days treatment in seawater, the wet tensile strength of the gel fiber retained 36% of the original untreated gel strength. For sodium alginates with similar viscosities, the seawater tolerance of low M/G ratio alginate was greater than that of the high M/G ratio one. This study enables us to determine a suitable calcium alginate gel for use in seawater.     

On the design of composite protein-quantum dot biomaterials via self-assembly

Incorporation of nanoparticles during the hierarchical self-assembly of protein-based materials can impart function to the resulting composite materials. Herein we demonstrate that the structure and nanoparticle distribution of composite fibers are sensitive to the method of nanoparticle addition and the physicochemical properties of both the nanoparticle and the protein. Our model system consists of a recombinant enhanced green fluorescent protein-Ultrabithorax (EGFP-Ubx) fusion protein and luminescent CdSe-ZnS core-shell quantum dots (QDs), allowing us to optically assess the distribution of both the protein and nanoparticle components within the composite material. Although QDs favorably interact with EGFP-Ubx monomers, the relatively rough surface morphology of composite fibers suggests EGFP-Ubx-QD conjugates impact self-assembly. Indeed, QDs templated onto EGFP-Ubx film post-self-assembly can be subsequently drawn into smooth composite fibers. Additionally, the QD surface charge impacts QD distribution within the composite material, indicating that surface charge plays an important role in self-assembly. QDs with either positively or negatively charged coatings significantly enhance fiber extensibility. Conversely, QDs coated with hydrophobic moieties and suspended in toluene produce composite fibers with a heterogeneous distribution of QDs and severely altered fiber morphology, indicating that toluene severely disrupts Ubx self-assembly. Understanding factors that impact the protein-nanoparticle interaction enables manipulation of the structure and mechanical properties of composite materials. Since proteins interact with nanoparticle surface coatings, these results should be applicable to other types of nanoparticles with similar chemical groups on the surface.     

Effects of different disinfection and sterilization methods on tensile strength of materials used for single-use devices

Driven by economic and time constraints, some medical centers and third parties are resterilizing single-use devices (SUDs) for reuse. The steam autoclave is quick, but most plastics used in SUDs cannot survive the temperature. Thus, a number of new methods of cleaning, disinfecting, and sterilizing these complex devices are being introduced on the market. The present study investigated the effects of a range of methods on the tensile strength of latex rubber, silicone elastomer, 2 different formulations of polyurethane, nylon, and high-density polyethylene (HDPE) specimens. The methods used were sodium hypochlorite bleach (Clorox), peracetic acid + hydrogen peroxide (Steris), formaldehyde gas (Chemiclave), low-temperature peracetic acid and gas plasma (Plazlyte), and low-temperature hydrogen peroxide gas plasma (Sterrad). The results showed that silicone elastomer was minimally affected, whereas the strengths of nylon, polyethylene, and latex were reduced by some of the methods. Depending on the formulation, the strength of polyurethane either increased or decreased. The data demonstrated that disinfection and sterilization can affect the tensile strength of certain materials used in medical devices.