TBAF and cellulose esters: unexpected deacylation with unexpected regioselectivity

Tetrabutylammonium fluoride has been found to catalyze the deacylation of cellulose esters. More surprisingly, the deacylation is highly regioselective. Even more remarkably, in contrast with the C-6 regioselectivity of other reactions of cellulose and its derivatives, this deacylation shows substantial selectivity for the removal of the acyl groups from the esters of the secondary alcohols at C-2 and C-3, affording cellulose-6-O-esters with high regioselectivity by a simple one-step process employing no protective groups.     

Probing anion-cellulose interactions in imidazolium-based room temperature ionic liquids: a density functional study

The interactions of the cellulose molecule with several anions, including acetate , alkyl phosphate, tetrafluoroborate and hexafluorophosphate anions which are most commonly involved in the imidazolium ionic liquids (ILs), have been studied by performing density functional theory calculations. Based on calculated geometries, energies, IR characteristics, and electronic properties of the cellulose-anion complexes, it is found that the strength of interactions of anions with cellulose follows the order: acetate anion > alkyl phosphate anion > tetrafluoroborate anion > hexafluorophosphate anion, which is consistent with the experimentally observed solubility trend of cellulose in the corresponding imidazolium-based ILs. The present study may provide basic aids to some extent for understanding the dissolution behavior of cellulose in the imidazolium-based ILs.     

Influence of steaming explosion time on the physic-chemical properties of cellulose from Lespedeza stalks (Lespedeza crytobotrya)

The synergistic effect of steam explosion pretreatment and sodium hydroxide post-treatment of Lespedeza stalks (Lespedeza crytobotrya) has been investigated in this study. In this case, Lespedeza stalks were firstly exploded at a fixed steam pressure (22.5 kg/m²) for 2–10 min. Then the steam-exploded Lespedeza stalks was extracted with 1 M NaOH at 50 °C for 3 h with a shrub to water ratio of 1:20 (g/ml), which yielded 57.3%, 53.1%, 55.4%, 52.8%, 53.2%, and 56.4% (% dry weight) cellulose rich fractions, comparing to 68.0% from non-steam-exploded material. The content of glucose in cellulose rich residues increased with increment of the steaming time and reached to 94.10% at the most severity. The similar increasing trend occurred during the dissolution of hemicelluloses. It is evident that at shorter steam explosion time, autohydrolysis mainly occurred on the hemicelluloses and the amorphous area of cellulose. The crystalline region of cellulose was depolymerized under a prolonged incubation time. The characteristics of the cellulose rich fractions in terms of FT-IR and CP/MAS ¹³C NMR spectroscopy and thermal analysis were discussed, and the surface structure was also investigated by SEM.     

Enhanced enzymatic saccharification of kenaf powder after ultrasonic pretreatment in ionic liquids at room temperature

This study demonstrates for the first time that the enzymatic hydrolysis of cellulose is drastically enhanced following ultrasonic pretreatment of lignocellulosic material in ionic liquids (ILs) when compared to conventional thermal pretreatment. Five types of ILs, 1-buthyl-3-methylimidazolium chloride (BmimCl), 1-allyl-3-methylimidazolium chloride (AmimCl), 1-ethyl-3-methylimidazolium chloride (EmimCl), 1-ethyl-3-methylimidazolium diethyl phosphate (EmimDep), and 1-ethyl-3-methylimidazolium acetate (EmimOAc) were tested. Cellulose saccharification ratio was about 20% for kenaf powders pretreated in BmimCl, AmimCl, EmimCl, and EmimDep by conventional heating at 110 °C for 120 min. Conversely, 60-95% of cellulose was hydrolyzed to glucose, subsequent to ultrasonic pretreatment in the same ILs for 120 min at 25 °C. The cellulose saccharification ratio of kenaf powder in EmimOAc was 86% after only 15 min of the ultrasonic pretreatment at 25 °C, compared to only 47% in that case of thermal pretreatment in the IL.     

Biocomposite films prepared from ionic liquid solutions of chitosan and cellulose

Blends of chitosan and cellulose were successfully produced using 1-butyl-3-methylimidazolium acetate (BMIMAc) as solvent media. Films were prepared from the blends by manually spreading the solution on a flat surface and precipitating the polymers in a mixture of methanol and water. To prevent the shrinkage of films, most of the absorbed water was removed by freeze drying under vacuum. Films prepared from the polymeric solutions were investigated by means of FT-IR, TGA, X-ray diffraction and SEM measurements. The shifting of the bands corresponding to -NH and CO groups of chitosan (FT-IR), the absence of the diffraction peaks at 2θ = 10.7 and 14.9° (XRD), the increased E_a for thermal decomposition for all the polymeric blends (MTGA), and the presence of an apparent homogeneous structure with no phase separation of the two polymers (SEM) provide evidence for the miscibility between chitosan and cellulose in the solid state.     

Quantitative determination of cellulose dissolved in 1-ethyl-3-methylimidazolium acetate using partial least squares regression on FTIR spectra

Rapid and quantitative measurements of cellulose concentrations in ionic liquids (ILs) are difficult. In this study, FTIR operated in attenuated total reflectance (ATR) mode was investigated as a tool to measure cellulose concentration in 1-ethyl-3-methylimidazolium acetate ([emim][OAc]) and the spectra were subjected to partial least squares (PLS) regression for the quantitative determination of cellulose content. Additionally, the spectra were subjected to 7 data preprocessing methods to reduce physical effects in the spectra. Peak normalization was found to be the technique that most improved the prediction of dissolved cellulose in [emim][OAc]. When peak normalization was used for data preprocessing, a model for the quantitative estimation of cellulose content between 0 wt.% and 4 wt.% with an error of 0.53 wt.% was generated. The methods described here provide the basis for a rapid and facile technique for the determination of dissolved cellulose content in [emim][OAc].     

The study of factors affecting the enzymatic hydrolysis of cellulose after ionic liquid pretreatment

Cellulose resource has got much attention as a promising replacement of fossil fuel. The hydrolysis of cellulose is the key step to chemical product and liquid transportation fuel. In this paper a serials of chloride, acetate, and formate based ionic liquids were used as solvents to dissolve cellulose. The cellulose regenerated from ILs was characterized by FTIR and X-ray powder diffraction. From the characterization and analysis, it was found that the original close and compact structure has changed a lot. After enzymatic hydrolysis, different kinds of ionic liquids (ILs) have different yields of the reducing sugar (TRS). They are 100%, 90.72%, and 88.92% from 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), 1-ethyl-3-methylimidazolium acetate ([EMIM][OAc]), 1-butyl-3-methylimidazolium formate ([BMIM][HCOO]) respectively after enzymatic hydrolysis at 50 °C for 5 h. The results indicated that the yields and the hydrolysis rates were improved apparently after ILs pretreatment comparing with the untreated substrates.     

Investigations about dissolution of cellulose in the 1-allyl-3-alkylimidazolium chloride ionic liquids

In this work, the 1-allyl-3-alkylimidazolium chloride ionic liquids were synthesized and characterized by increasing carbon atoms (n ≤ 6) of alkyl chains on a cationic 3-imidazole ring. The results indicated that 1-allyl-3-alkylimidazolium chloride with asymmetrical structure on the two sides of a cationic 3-imidazole ring (i.e., n = 1, 2, 6) exhibited alkalinity and lower thermal stabilities, and showed better solubility to the cellulose samples at 60-120 °C than those with symmetrical structures (n = 3, 4). The cellulose samples treated by 20% (w/w) ethylenediamine solution showed better solubility in 1-allyl-3-ethyl, hexyl-imidazolium chloride ionic liquids than that treated with 20% (w/w) NaOH solution at 5 °C for 72 h. XRD and TG analysis indicated that 0 0 2 plane apparent crystallite size as well as thermal stability of the regenerated cellulose samples from the ionic liquids decreased significantly compared with the untreated cellulose samples.     

Zinc chloride mediated degradation of cellulose at 200 °C and identification of the products

The effect of ZnCl₂ on the degradation of cellulose was studied to develop conditions to produce useful feedstock chemicals directly from cellulosic biomass. Cellulose containing 0.5 mol of ZnCl₂/mol of glucose unit of cellulose was found to degrade at 200 °C when heated for more than 60 s in air. The major non-gaseous products of the degradation were identified as furfural, 5-hydroxymethylfurfural and levulinic acid. The maximum yields for furfural and 5-hydroxymethylfurfural are 8% and 9%, respectively, based on glucose unit of cellulose. These yields are reached after 150 s of heating at 200 °C. A cellulose sample containing 0.5 mol of ZnCl₂/mol of glucose unit of cellulose and 5.6 equivalents of water when heated for 150 s at 200 °C produced levulinic acid as the only product in 6% yield. The ZnCl₂ mediated controlled degradation of cellulose at 200 °C is shown to produce useful feedstock chemicals in low yield.     

Carboxymethylation of cellulose using reactive extrusion

Carboxymethyl cellulose was prepared using a continuous, reduced solvent, reactive extrusion process with a short reaction time. The effects of the amounts of NaOH (30 g, 40 g and 50 g), water:ethanol ratio (100%, 70%, 50%, 30% and 10% H₂O) and their interactions on the physical, chemical and morphological properties of carboxymethyl cellulose were studied. Experiments were conducted using to a 5 × 3 blocked factorial design. X-ray diffraction analyses revealed higher degrees of crystallinity and fractions of cellulose-II crystalline structure when 100% H₂O was used as compared to that for 70%, 50%, 30% and 10% H₂O and a commercially available brand of carboxymethyl cellulose, AQUASORB A500. Statistical analysis revealed a significant interaction between the effects of NaOH and H₂O on the degrees of substitutions. The degrees of substitutions decreased with increasing amounts of NaOH and tended to increase with increasing alcohol concentrations. Liquid uptake measurements revealed that the extent of saline uptake, measured at intervals of 1 min, 5 min and 10 min, by carboxymethyl cellulose prepared with 100% H₂O, especially when 40 g and 50 g NaOH was used, was higher than that for 70%, 50%, 30% and 10% H₂O and AQUASORB A500. This may have been because of the higher crystallinity in carboxymethyl cellulose prepared with 100% H₂O. Carboxymethyl cellulose prepared with 70% H₂O and 30 g and 50 g NaOH had the highest saline absorption, using the soak method, before and after centrifugation, respectively. Scanning electron microscopy for carboxymethyl cellulose prepared with 100% and 10% H₂O, through images at 120X magnification, revealed fibers 100 μ to >800 μ in length and 0.8-3.3 μ in breadth. Some non fibrous particles, 0.8-6.7 μ in dimensions, also were observed for 100% H₂O. Images at 900× magnification revealed partially damaged fiber surfaces.     

Comb-shaped graft copolymers with cellulose side-chains prepared via click chemistry

Comb-shaped copolymers with cellobiose acetate or cellulose triacetate (CTA) side-chains, PPMA-g-(CTA2-C15) and PPMA-g-(CTA13-C15), were prepared by grafting N-(15-azidopentadecanoyl)-2,3,6-tri-O-acetyl-4-O-(2,3,4,6-tetra-O-acetyl-β-d-glucopyranosyl)-β-d-glucopyranosylamine (CTA2-C15-N₃) and N-(15-azidopentadecanoyl)-tri-O-acetyl-β-cellulosylamine (CTA13-C15-N₃, number average degree of polymerization (DP_n) = 13) onto poly(2-propyn-1-yl methacrylate) (PPMA, weight average degree of polymerization (DP_w, X + Y = 5.59 × 10²)) via “click chemistry”. The copolymers were characterized by ¹H, ¹³C and two-dimensional NMR and size exclusion chromatography-multi-angle laser light scattering (SEC-MALS) measurements. The numbers of CTA side-chains (X) of PPMA-g-(CTA2-C15) and PPMA-g-(CTA13-C15) were calculated as 4.03 × 10² and 2.45 × 10², respectively. Copolymers with cellulosic side-chains, PPMA-g-(CELL2-C15) and PPMA-g-(CELL13-C15), were successfully obtained after deacetylation of PPMA-g-(CTA2-C15) and PPMA-g-(CTA13-C15), respectively. X-ray diffraction measurements revealed that PPMA-g-(CELL13-C15) showed crystalline pattern of cellulose II, which is believed to have anti-parallel orientation.     

Liquid hot water and alkaline pretreatment of soybean straw for improving cellulose digestibility

Soybean straw was pretreated with either liquid hot water (LHW) (170-210 °C for 3-10 min) or alkaline soaking (4-40 g NaOH/100 g dry straw) at room temperature to evaluate the effects on cellulose digestibility. Nearly 100% cellulose was recovered in pretreated solids for both pretreatment methods. For LHW pretreatment, xylan dissolution from the raw material increased with pretreatment temperature and time. Cellulose digestibility was correlated with xylan dissolution. A maximal glucose yield of 70.76%, corresponding to 80% xylan removal, was obtained with soybean straw pretreated at 210 °C for 10 min. NaOH soaking at ambient conditions removed xylan up to 46.37% and the subsequent glucose yield of pretreated solids reached up to 64.55%. Our results indicated LHW pretreatment was more effective than NaOH soaking for improving cellulose digestibility of soybean straw.     

New 6-butylamino-6-deoxycellulose and 6-deoxy-6-pyridiniumcellulose derivatives with highest regioselectivity and completeness of reaction

This paper investigates the nucleophilic substitution (S(N)) reactions of tosylcellulose with butylamine and pyridine, respectively. The S(N) reactions of tosylcellulose 1 (DS(Total) 2.02; DS(C-6) 1.0) with butylamine carried out at 25, 50, 75 and 100 degrees C in both dimethyl sulfoxide (DMSO) and pure butylamine showed that the regioselectivity of substitution at C-6 of cellulose is temperature dependent: the highest regioselectivity at C-6 can be reached at 25 and 50 degrees C; substitution at C-2 also occurred at 75 and 100 degrees C. The substitution speed in pure butylamine is greater than that in the presence of DMSO. A complete and regioselective substitution at C-6 with a DS of 1.0 was obtained under the conditions of 50 degrees C, 40 h in butylamine. The substitution reactions of 1 with pyridine carried out at 25, 50, 75 and 100 degrees C for 24h in DMSO did not occur. In contrast to this the S(N) reactions done in pure pyridine showed that a temperature- and steric-dependent, regioselective substitution took place at C-6 at temperatures from 25 to 145 degrees C. The highest regioselectivity and completeness at C-6 can be obtained at 100 degrees C for 90 h, whereas at 145 degrees C substitution also occurs at C-2. The results were proved by 1H NMR and 13C NMR spectroscopy.     

Bioconversion of wheat stalk to hydrogen by dark fermentation: effect of different mixed microflora on hydrogen yield and cellulose solubilisation

This study determined hydrogen production, volatile fatty acids (VFAs) generation and cellulose solubilisation from anaerobic dark fermentation of wheat stalk and showed the effect of different mixed microflora. The cumulative hydrogen yields of anaerobic digested activated sludge (AS)-inoculated and anaerobic digested dairy manure (DM)-inoculated system were 23.3 and 37.0 mL/g VS at 204 h, respectively. A modified Gompertz equation was able to adequately describe the production of hydrogen from the batch fermentation by both mixed microflora. During the process, acetate and butyrate accounted for more than 76.1% of total VFAs for both fermentations. The extent of cellulose solubilisation approached 46.6% and 75.2% for AS- and DM-inoculated fermentation, respectively. The X-ray diffraction (XRD) showed that the crystallinities of both fermented stalks were partly disrupted by the mixed microflora, and DM-inoculated fermentation had more disruption than AS-inoculated one.     

Novel regenerated cellulose films prepared by coagulating with water: Structure and properties

Regenerated films were successfully prepared from cellulose/NaOH/urea solution by coagulating with water at temperature from 25 to 45 °C. The results of solid ¹³C NMR, wide angle X-ray diffraction, scanning electron microscopy (SEM) and tensile testing revealed that the cellulose films possessed homogeneous structure and cellulose II crystalline, similar to that prepared previously by coagulating with 5 wt% H₂SO₄. By changing the coagulation temperature from 25 to 45 °C, tensile strength of the films was in the range of 85-139 MPa. Interestingly, the RC35 film coagulated at 35 °C exhibited the highest tensile strength (σ_b = 139 MPa). The inclusion complex associated with cellulose, NaOH and urea hydrates in the cellulose solution were broken by adding water (non-solvent), leading to the self-association of cellulose to regenerate through rearrangement of the hydrogen bonds. This work provided low-cost and “green” pathway to prepare cellulose films, which is important in industry.     

Cellulose isolation and core-shell nanostructures of cellulose nanocrystals from chardonnay grape skins

This is the first report on the derivation and structures of cellulose nanocrystals from grape skins. Pure cellulose was isolated from chardonnay grape skins at a 16.4% yield by a process involving organic extraction, acid and base dissolutions, and basic and acidic oxidation. The as-extracted cellulose was 54.9% crystalline and microfibrillar. Acid hydrolysis (64-65% H₂SO₄ 45 °C, 30 min) of grape skin cellulose produced the more crystalline (64.3%) cellulose nanocrystals (CNCs) that appeared mostly as spherical nanoparticles with diameters ranging from 10 to 100 nm and a mean diameter of 48.1 (±14.6) nm as observed by TEM. AFM further disclosed the spherical nanoparticles actually consist of a nano-rod core (seed) surrounded by numerous tiny cellulose fragments as the shell. Interestingly, the spherical core-shell nanoparticles resemble the shape of grape bundles, the starting biomass, may be assembled via interfacial hydrogen bonds.     

Mode of action on deacetylation of acetylated methyl glycoside by cellulose acetate esterase from Neisseria sicca SB

The regioselective deacetylation of purified cellulose acetate esterase from Neisseria sicca SB was investigated on methyl 2,3,4,6-tetra-O-acetyl-beta-D-glucopyranoside and 2,3,4,6-tetra-O-acetyl-beta-D-galactopyranoside. The substrates were used as model compounds of cellulose acetate in order to estimate the mechanism for deacetylation of cellulose acetate by the enzyme. The enzyme rapidly deacetylated at position C-3 of methyl 2,3,4,6-tetra-O-acetyl-beta-D-glucopyranoside to accumulate 2,4,6-triacetate as the main initial reaction product in about 70% yield. Deacetylation was followed at position C-2, and generated 4,6-diacetate in 50% yield. The enzyme deacetylated the product at positions C-4 and C-6 at slower rates, and generated 4- and 6-monoacetates at a later reaction stage. Finally, it gave a completely deacetylated product. For 2,3,4,6-tetra-O-acetyl-beta-D-galactopyranoside, CA esterase deacetylated at positions C-3 and C-6 to give 2,4,6- and 2,3,4-triacetate. Deacetylation proceeded sequentially at positions C-3 and C-6 to accumulate 2,4-diacetate in 55% yield. The enzyme exhibited regioselectivity for the deacetylation of the acetylglycoside.     

Catalytic hydrolysis of lignocellulosic biomass into 5-hydroxymethylfurfural in ionic liquid

Production of 5-hydroxymethylfurfural (HMF) from cellulose catalyzed by solid acids and metal chlorides was studied in the 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) under microwave irradiation. Among the applied catalysts, the use of CrCl₃/LiCl resulted in the highest yield of HMF. The effects of catalyst dosage (mole ratio of catalyst to glucose units in the feedstock) and reaction temperature on HMF yields were investigated to obtain optimal process conditions. With the 1:1 mol ratio of catalyst to glucose unit, the HMF yield reached 62.3% at 160 °C for 10 min. Untreated wheat straw was also investigated as feedstock to produce HMF for the practical use of raw biomass, in which the HMF yield was comparable to that from pure cellulose. After the extraction of HMF, [BMIM]Cl and CrCl₃/LiCl could be reused and exhibited no activity loss after three successive runs.     

Preparation and characterization of cellulose nanocrystals from rice straw

Pure cellulose have been isolated from rice straw at 36% yield and hydrolyzed (64% H₂SO₄, 8.75 mL/g, 45 °C) for 30 and 45 min to cellulose nanocrystals (CNCs), i.e., CNC30 and CNC45, respectively. CNC45 was smaller (11.2 nm wide, 5.06 nm thick and 117 nm long) than CNC30 (30.7 nm wide, 5.95 nm thick and 270 nm long). Freeze-drying of diluted CNC suspensions showed both assembled into long fibrous structures: ultra-fine fibers (∼400 nm wide) from CNC45 and 1-2 μm wide broad ribbons interspersed with CNC clusters from CNC30. The self-assembled fibers from CNC30 and CNC45 were more highly crystalline (86.0% and 91.2%, respectively) and contained larger crystallites (7.36 nm and 8.33 nm, respectively) than rice straw cellulose (61.8%, 4.42 nm). These self-assembled fibers had essentially nonporous or macroporous structures with the CNCs well aligned along the fiber axis. Furthermore, the self-assembled ultra-fine fibers showed extraordinary structural stability, withstanding vigorous shaking and prolong stirring in water.