Microbial activity of suspended biomass from a nitritation–anammox SBR in dependence of operational condition and size fraction

Single-stage nitritation–anammox combines the growth of aerobic ammonium-oxidizing bacteria (AOB) and anaerobic ammonium oxidizing bacteria (AnAOB) in one reactor. The necessary compromise of their milieu conditions often leads to the growth of nitrite-oxidizing bacteria (NOB). For this study, a sequencing batch reactor (SBR) for nitritation–anammox was operated for 180 days with sewage sludge reject water (removal capacity, 0.4 kg?N?m^?3?day^?1). The growth of NOB was favored by enhanced oxygen supply rather than extended aerobic phases. Suspended-type biomass from this SBR was taken regularly and sieved into three size fractions (all of them <1,000 μm). Batch experiments as well as fluorescence in situ hybridization were performed to study the distribution and activity of AnAOB, AOB, and NOB within those size fractions. Both the measured conversion rates and detected abundances decreased with increasing size fraction. The highest anammox conversion rates (15 g NH₄ ⁺–N per kilogram VSS per hour) and the highest abundances of Brocadia fulgida were found in the medium size fraction (100–315 μm). The batch experiments proved to be accurate tools for the monitoring of multiple processes in the reactor. The results were representative for reactor performance during the 6 months of reactor operation.     

Activated sludge under free ammonia treatment using gel immobilization technology for long-term partial nitrification with different initial biomass

To achieve stable partial nitrification, activated sludge from a wastewater treatment plant using free ammonia (FA) inhibition was immobilized in a polyvinyl alcohol carrier. After FA treatment at 16.44 mg L⁻¹ for 1 day, due to the increased growth rate gap between ammonium-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria (NOB), AOB enrichment and NOB inhibition were achieved within 12 days, with AOB and NOB accounting for 65.61 and 0.05%, respectively. Subsequently, with dissolved oxygen concentrations of 4−5 mg L⁻¹, pH of 7.6–7.8 and temperature of 25 ± 1 °C, the immobilized carrier made of activated sludge achieved more than 90% and more than 86% of nitrite accumulation rate at the influent ammonia concentration of 90−110 mg L⁻¹ and 35−50 mg L⁻¹, respectively. After 50 days operation, the NOB content was 0.10%, indicating the immobilized carrier provided favorable conditions for maintaining the low NOB content. Furthermore, due to the low NOB content in the inoculum and the oxygen-limited environment formed by the increase in the AOB numbers in the carrier, immobilized carrier with different initial biomass (1, 2.5 and 5%) can achieve stable partial nitrification.     

Elicitor mediated enhancement of wedelolactone in cell suspension culture of <Emphasis Type="Italic">Eclipta alba</Emphasis> (L.) Hassk

The present research focused on enhancing the production of wedelolactone through cell suspension culture (CSC) in Eclipta alba (L.) Hassk. With an aim of attaining a sustainable CSC, various plant growth regulators, elicitors and agitation speed were examined. Nodal segments of in vitro propagated plantlets induced the maximum percentage (93.47?±?0.61%) of callus inoculated on Murashige and Skoog (MS) medium fortified with picloram (2 mg L^?1). The growth kinetics of CSC exhibited a sigmoid pattern with a lag phase (0–6 days), a log phase (6–18 days), a stationary phase (18–24 days) and then death phase thereafter. The highest biomass accumulation in CSC with 7.09?±?0.06 g 50 mL^?1 fresh weight, 1.52?±?0.02 g 50 mL^?1 dry cell weight, 1.34?±?0.01?×?10⁶ cell mL^?1 total cell count and 57.00?±?0.58% packed cell volume was obtained in the liquid MS medium supplemented with 1.5 mg L^?1 picloram plus 0.5 mg L^?1 kinetin at 120 rpm. High performance thin layer chromatography confirmed that yeast extract (biotic elicitor) at 150 mg L^?1 accumulated more CSC biomass with 1.22-fold increase in wedelolactone (288.97?±?1.94 µg g^?1 dry weight) content in comparison to the non-elicited CSC (237.78?±?0.04 µg g^?1 dry weight) after 120 h of incubation. Contrastingly, methyl jasmonate (abiotic elicitor) did not alter the biomass but increased the wedelolactone content (259.32?±?1.06 µg g^?1 dry weight) to an extent of 1.09-fold at 100 µM. Complete plantlet regeneration from CSC was possible on MS medium containing N⁶-benzyladenine (0.75 mg L^?1) and abscisic acid (0.5 mg L^?1). Thus, the establishment of protocol for CSC constitutes the bases for future biotechnological improvement studies in this crop.     

Process Engineering for High-Cell-Density Cultivation of Lipid Rich Microalgal Biomass of <Emphasis Type="Italic">Chlorella</Emphasis> sp. FC2 IITG

In the present study, process engineering strategy was applied to achieve lipid-rich biomass with high density of Chlorella sp. FC2 IITG under photoautotrophic condition. The strategy involved medium optimization, intermittent feeding of limiting nutrients, dynamic change in light intensity, and decoupling growth and lipid induction phases. Medium optimization was performed using combinations of artificial neural network or response surface methodology with genetic algorithm (ANN-GA and RSM-GA). Further, a fed-batch operation was employed to achieve high cell density with intermittent feeding of nitrate and phosphate along with stepwise increase in light intensity. Finally, mutually exclusive biomass and lipid production phases were decoupled into two-stage cultivation process: biomass generation in first stage under nutrient sufficient condition followed by lipid enrichment through nitrogen starvation. The key findings were as follows: (i) ANN-GA resulted in an increase in biomass titer of 157 % (0.95 g L^?1) in shake flask and 42.8 % (1.0 g L^?1) in bioreactor against unoptimized medium at light intensity of 20 μE m^?2 s^?1; (ii) further optimization of light intensity in bioreactor gave significantly improved biomass titer of 5.6 g L^?1 at light intensity of 250 μE m^?2 s^?1; (iii) high cell density of 13.5 g L^?1 with biomass productivity of 675 mg L^?1 day^?1 was achieved with dynamic increase in light intensity and intermittent feeding of limiting nutrients; (iv) finally, two-phase cultivation resulted in biomass titer of 17.7 g L^?1 and total lipid productivity of 313 mg L^?1 day^?1 which was highest among Chlorella sp. under photoautotrophic condition.     

Productivity and biochemical composition of <Emphasis Type="Italic">Tetradesmus obliquus</Emphasis> and <Emphasis Type="Italic">Phaeodactylum tricornutum</Emphasis>: effects of different cultivation approaches

The present work evaluated biomass productivity, carbon dioxide fixation rate, and biochemical composition of two microalgal species, Phaeodactylum tricornutum (Bacillariophyta) and Tetradesmus obliquus (Chlorophyta), cultivated indoors in high-technology photobioreactors (HT-PBR) and outdoors both in pilot ponds and low-technology photobioreactors in a greenhouse in southern Italy. Microalgae were grown in standard media, under nitrogen starvation, and in two liquid digestates obtained from anaerobic digestion of agro-zootechnical and vegetable biomass. P. tricornutum, cultivated in semi-continuous mode in indoor HT-PBRs with standard medium, showed a biomass productivity of 21.0?±?2.3 g m^?2 d^?1. Applying nitrogen starvation, the lipid productivity increased from 2.3 up to 4.5?±?0.5 g m^?2 d^?1, with a 24 % decrease of biomass productivity. For T. obliquus, a biomass productivity of 9.1?±?0.9 g m^?2 d^?1 in indoor HT-PBR was obtained using standard medium. Applying liquid digestates as fertilizers in open ponds, T. obliquus gave a biomass productivity (10.8?±?2.0 g m^?2 d^?1) not statistically different from complete medium such as P. tricornutum (6.5?±?2.2 g m^?2 d^?1). The biochemical data showed that the fatty acid composition of the microalgal biomass was affected by the different cultivation conditions for both microalgae. In conclusion, it was found that the microalgal productivity in standard medium was about doubled in HT-PBR compared to open ponds for P. tricornutum and was about 20 % higher for T. obliquus.     

Effects of stationary phase elongation and initial nitrogen and phosphorus concentrations on the growth and lipid-producing potential of Chlorella sp. HQ

Higher lipid production and nutrient removal rates are the pursuing goals for synchronous biodiesel production and wastewater treatment technology. An oleaginous alga Chlorella sp. HQ was tested in five different synthetic water, and it was found to achieve the maximum biomass (0.27 g L^?1) and lipid yield (41.3 mg L^?1) in the synthetic secondary effluent. Next, the effects of the stationary phase elongation and initial nitrogen (N) and phosphorus (P) concentrations were investigated. The results show that the algal characteristics were affected apparently under different N concentrations but not P, which were verified by Logistic and Monod models. At the early stationary phase, the algal biomass, lipid and triacylglycerols (TAGs) yields, and P removal efficiency increased and reached up to 0.19 g L^?1, 46.7 mg L^?1, 14.3 mg L^?1, and 94.3 %, respectively, but N removal efficiency decreased from 86.2 to 26.8 % under different N concentrations. And the largest TAGs yield was only 6.4 mg L^?1 and N removal efficiency was above 71.1 % under different P concentrations. At the late stationary phase, the maximal biomass, lipid and TAGs yields, and P removal efficiencies primarily increased as the initial N and P concentrations increase and climbed up to 0.49 g L^?1, 99.2 mg L^?1, 54.0 mg L^?1, and 100.0 %, respectively. It is concluded that stationary phase elongation is of great importance and the optimal initial N/P ratio should be controlled between 8/1 and 20/1 to serve Chlorella sp. HQ for better biodiesel production and secondary effluent purification.     

Wastewater treatment and biofuel production through attached culture of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> in a porous substratum biofilm reactor

The feasibility of attached culture Chlorella vulgaris in a porous substratum biofilm reactor (PSBR) for simultaneous wastewater treatment and biofuel production was investigated. The characteristics, including algal biofilm growth, lipid yield, nutrient removal, and energy efficiency of the outdoor cultures, were investigated under the influence of both inoculum densities and the percent submerged area. A maximum biofilm productivity of 57.87 g m^?2 d^?1 with 81.9 % adhesion was achieved under optimal conditions (inoculum density of 18 g m^?2 and the percent submerged area of 5.7 %). The lipid content and lipid yield were 38.56 % and 27.25 g m^?2 d^?1, respectively. Meanwhile, the algae removed 99.95 % ammonia, 96.05 % total nitrogen (TN), and 99.83 % total phosphorus (TP). Further, the energy life cycle for the PSBR was analyzed. The biomass productivity per unit irradiance was up to 4.6 g MJ^?1 (photosynthetic efficiency of 10.65 %). The PSBR was considered to be economically feasible due to the net energy ratio of 1.3 (>1).     

Biological CO<Subscript>2</Subscript> fixation using C<Emphasis Type="Italic">hlorella vulgaris</Emphasis> and its thermal characteristics through thermogravimetric analysis

The present research is focused on cultivation of microalgae strain Chlorella vulgaris for bio-fixation of CO₂ coupled with biomass production. In this regard, a single semi-batch vertical tubular photobioreactor and four similar photobioreactors in series have been employed. The concentration of CO₂ in the feed stream was varied from 2 to 12 % (v/v) by adjusting CO₂ to air ratio. The amount of CO₂ capture and algae growth were monitored by measuring decrease of CO₂ concentration in the gas phase, microalgal cell density, and algal biomass production rate. The results show that 4 % CO₂ gives maximum amount of biomass (0.9 g L^?1) and productivity (0.118 g L^?1 day^?1) of C. vulgaris in a single reactor. In series reactors, average productivity per reactor found to be 0.078 g L^?1 day^?1. The maximum CO₂ uptake for single reactor also found with 4 % CO_2, and it is around 0.2 g L^?1 day^?1. In series reactors, average CO₂ uptake is 0.13 g L^?1 day^?1 per reactor. TOC analysis shows that the carbon content of the produced biomass is around 40.67 % of total weight. The thermochemical characteristics of the cultivated C. vulgaris samples were analyzed in the presence of air. All samples burn above 200 °C and the combustion rate become faster at around 600 °C. Almost 98 wt% of the produced biomass is combustible in this range.     

Improvement of biomass and fatty acid productivity in ocean cultivation of <Emphasis Type="Italic">Tetraselmis</Emphasis> sp. using hypersaline medium

In this study, hypersaline media were used for ocean cultivation of the marine microalga Tetraselmis sp. KCTC12432BP for enhanced biomass and fatty acid (FA) productivity. Hypersaline media (55, 80, and 105 PSU) were prepared without sterilization by addition of NaCl to seawater obtained from Incheon, Korea. The highest biomass productivity was obtained at 55 PSU (0.16 g L^?1 day^?1) followed by 80 PSU (0.15 g L^?1 day^?1). Although the specific growth rate of Tetraselmis decreased at salinities higher than 55 PSU, prevention of contamination led to higher biomass productivity at 80 PSU than at 30 PSU (0.03 g L^?1 day^?1). FA content of algal biomass increased as salinity increased to 80 PSU, above which it declined, and FA productivity was highest at 80 PSU. Ocean cultivation of Tetraselmis was performed using 50-L tubular module photobioreactors and 2.5-kL square basic ponds, closed- and open-type ocean culture systems, respectively. Culturing microalgae in hypersaline medium (80 PSU) improved biomass productivities by 89 and 152% in closed and open cultures, respectively, compared with cultures with regular salinity. FA productivity was greatly improved by 369% in the closed cultures. The efficacy of salinity shift and N-deficiency to enhance FA productivity was also investigated. Lowering salinity to 30 PSU with N-starvation following cultivation at 80 PSU improved FA productivity by 19% in comparison with single-stage culture without N-deficiency at 30 PSU. The results show that salinity manipulation could be an effective strategy to improve biomass and FA productivity in ocean cultivation of Tetraselmis sp.     

Inoculum effects on community composition and nitritation performance of autotrophic nitrifying biofilm reactors with counter‐diffusion geometry

The link between nitritation success in a membrane‐aerated biofilm reactor (MABR) and the composition of the initial ammonia‐ and nitrite‐oxidizing bacterial (AOB and NOB) population was investigated. Four identically operated flat‐sheet type MABRs were initiated with two different inocula: from an autotrophic nitrifying bioreactor (Inoculum A) or from a municipal wastewater treatment plant (Inoculum B). Higher nitritation efficiencies (NO₂^‐‐N/NH₄⁺‐N) were obtained in the Inoculum B‐ (55.2–56.4%) versus the Inoculum A‐ (20.2–22.1%) initiated reactors. The biofilms had similar oxygen penetration depths (100–150 µm), but the AOB profiles [based on 16S rRNA gene targeted real‐time quantitative PCR (qPCR)] revealed different peak densities at or distant from the membrane surface in the Inoculum B‐ versus A‐initiated reactors, respectively. Quantitative fluorescence in situ hybridization (FISH) revealed that the predominant AOB in the Inoculum A‐ and B‐initiated reactors were Nitrosospira spp. (48.9–61.2%) versus halophilic and halotolerant Nitrosomonas spp. (54.8–63.7%), respectively. The latter biofilm displayed a higher specific AOB activity than the former biofilm (1.65 fmol cell^?1 h^?1 versus 0.79 fmol cell^?1 h^?1). These observations suggest that the AOB and NOB population compositions of the inoculum may determine dominant AOB in the MABR biofilm, which in turn affects the degree of attainable nitritation in an MABR.     

Key parameters for outdoor biomass production of Scenedesmus obliquus in solar tracked photobioreactors

The biomass productivity of Scenedesmus obliquus was investigated outdoors during all seasons in solar tracked flat panel photobioreactors (PBR) to evaluate key parameters for process optimization. CO₂ was supplied by flue gas from an attached combined block heat and power plant. Waste heat from the power plant was used to heat the culture during winter. The parameters pH, CO₂, and inorganic salt concentrations were automatically adjusted to nonlimiting levels. The optimum biomass concentration increased directly with the photosynthetic active radiation (PAR) from 3 to 5 g dry weight (DW)?L^?1 for a low PAR of 10 mol photons m^?2 day^?1 and high PAR of 40–60 mol photons m^?2 day^?1, respectively. The annual average biomass yield (photosynthetic efficiency) was 0.4?±?0.5 g DW mol^?1 photons. However, biomass yields of 1.5 g DW mol^?1 photons close to the theoretical maximum were obtained at low PAR. The productivity (including the night biomass losses) ranged during all seasons from ?5 up to 30 g DW m^?2 day^?1 with a mean productivity of 9?±?7 g DW m^?2 day^?1. Low night temperatures of the culture medium and elevated day temperatures to the species-specific optimum increased the productivity. Thus, continuous regulation of the biomass concentration and the culture temperature with regard to the fluctuating weather conditions is essential for process optimization of outdoor microalgal production systems in temperate climates.     

Batch and semi-continuous microalgal TAG production in lab-scale and outdoor photobioreactors

Microalgal triglycerides (TAGs) represent a sustainable feedstock for food, chemical and biofuel industries. The operational strategy (batch, semi-continuous, continuous cultivations) has an impact on the TAG productivity. In this study, semi-continuous (i.e. with fixed harvesting frequency) and batch cultivations were compared on TAG production both at lab-scale and in outdoor cultivations. At lab-scale, the semi-continuous TAG productivity was highest for a cycle time of 2 days (SC1; 0.21 g L^?1 day^?1) and similar to the maximum obtained with the batch (optimal harvest time; 0.23 g L^?1 day^?1). Although TAG content was lower for SC1 (22 %) than for the batch (35 %), higher biomass productivities were obtained with SC1. Outdoors, semi-continuous cultivations were subjected to a lower degree of stress (i.e. higher amount of nitrogen present in the system relative to the given irradiance) compared to lab-scale. This yielded low and similar TAG contents (10–13 %) in the different semi-continuous runs that were outdone by the batch on both TAG content (15–25 %) and productivity (batch, 0.97–2.46 g m^?2 day^?1; semi-continuous, 0.35–0.85 g m^?2 day^?1). The lab-scale experiments showed that semi-continuous strategies, besides leading to similar TAG productivities compared to the batch, could make TAG production cost effective by valorising also non-TAG compounds. However, optimization of outdoor semi-continuous cultivations is still required. For instance, the nitrogen supply and the harvest frequency should be adjusted on the total irradiance. Additionally, future research should focus on recovery metabolism upon nitrogen resupply.     

Attached culture of Nannochloropsis oculata for lipid production

The influences of urea, nitrate and glycine with four concentration levels on attached culture of Nannochloropsis oculata were investigated. The organic nitrogen source glycine was effective on improving not only adhesion biomass productivity but also adhesion rate. The maximum adhesion biomass productivity of 15.76 ± 0.52 g m^?2 day^?1 with adhesion rate of 76.67 ± 0.42 % was achieved with 18 mM glycine. To increase the lipid production, three lipid enhancing strategies were conducted afterwards, including nitrogen starvation, high light, and the combination of nitrogen starvation and high light. In nitrogen starvation situation, although the lipid content was greatly increased, the adhesion biomass productivity dropped probably due to the low cell viability. Increasing light intensity was effective on enhancing both adhesion biomass productivity and lipid content. The results indicated that nitrogen starvation was effective on improving both lipid content and adhesion rate when high light was applied. The maximum lipid yield of 4.32 ± 0.14 g m^?2 day^?1 with adhesion biomass productivity of 21.32 ± 0.65 g m^?2 day^?1, adhesion rate of 86.81 ± 0.10 % and lipid content of 20.24 ± 0.06 % was achieved with the combination strategy.     

Biomass productivity of two <Emphasis Type="Italic">Scenedesmus</Emphasis> strains cultivated semi-continuously in outdoor raceway ponds and flat-panel photobioreactors

Semi-continuous algal cultivation was completed in outdoor flat-panel photobioreactors (panels) and open raceway ponds (raceways) from February 17 to May 7, 2015 for side-by-side comparison of areal productivities at the Arizona Center for Algae Technology and Innovation in Mesa, AZ, USA. Experiments used two strains of Scenedesmus acutus (strains LB 0414 and LB 0424) to assess productivity, areal density, nutrient removal, and harvest volume across cultivation systems and algal strains. Panels showed an average biomass productivity of 19.0?±?0.6 g m^?2 day^?1 compared to 6.62?±?2.3 g m^?2 day^?1 for raceways. Photosynthetic efficiency ranged between 1.32 and 2.24 % for panels and between 0.30 and 0.68 % for raceways. Panels showed an average nitrogen consumption rate of 38.4?±?8.6 mg N L^?1 day^?1. Cultivation in raceways showed a consumption rate of 3.8?±?2.5 and 7.1?±?4.2 mg N L^?1 day^?1 for February/March and April/May, respectively, due to increase in biomass productivity. Excess nutrients were required to prevent a decrease in productivity. Daily biomass harvest volumes between 18 and 36 % from panels did not affect culture productivity, but density decreased with increased harvest volume. High cultivation temperatures above 30 °C caused strain LB 0414 to lyse and crash. Strain LB 0424 did not show any difference in biomass productivity when peak temperatures reached 34, 38, or 42 °C, but showed decreased productivity when the peak temperature during cultivation was 30 °C. Using algal strains with different temperature tolerances can generate increased annual biomass productivity.     

Dry anaerobic digestion of high solids content dairy manure at high organic loading rates in psychrophilic sequence batch reactor

Cow manure with bedding is renewable organic biomass available around the year on dairy farms. Developing efficient and cost-effective psychrophilic dry anaerobic digestion (PDAD) processes could contribute to solving farm-related environmental, energy, and manure management problems in cold-climate regions. This study was to increase the organic loading rate (OLR), fed to a novel psychrophilic (20 °C) dry anaerobic digestion of 27 % total solid dairy manure (cow feces and wheat straw) in sequence batch reactor (PDAD-SBR), by 133 to 160 %. The PDAD-SBR process operated at treatment cycle length of 21 days and OLR of 7.0 and 8.0 g total chemical oxygen demand (TCOD)?kg^?1 inoculum day^?1 (5.2?±?0.1 and 5.8?±?0.0 g volatile solids (VS)?kg^?1 inoculum day^?1) for four successive cycles (84 days) produced average specific methane yields (SMYs) of 147.1?±?17.2 and 143.2?±?11.7 normalized liters (NL)?CH₄?kg^?1 VS fed, respectively. PDAD of cow feces and wheat straw is possible with VS-based inoculum-to-substrate ratio of 1.45 at OLR of 8.0 g TCOD kg^?1 inoculum day^?1. Hydrolysis was the limiting step reaction. The VS removal averaged around 57.4?±?0.5 and 60.5?±?5.7 % at OLR 7.0 and 8.0 g TCOD kg^?1 inoculum day^?1, respectively.     

Increased production of γ-lactones from hydroxy fatty acids by whole Waltomyces lipofer cells induced with oleic acid

Among several fatty acids tested, oleic acid was selected as the most efficient inducer for the production of 4-hydroxydodecanoic acid, a metabolite of β-oxidation, by Waltomyces lipofer. Cells were induced by incubation for 12 h in a medium containing 10 g l^?1 yeast extract, 10 g l^?1 peptone, 5 g l^?1 oleic acid, 1 g l^?1 glucose, and 0.05 % (w/v) Tween 80. The optimal reaction conditions for the production of γ-lactones by induced cells were pH 6.5, 35 °C, 200 rpm, 0.71 M Tris, 60 g l^?1 hydroxy fatty acid, and 20 g l^?1 cells. Non-induced cells produced 38 g l^?1 γ-dodecalactone from 60 g l^?1 10-hydroxystearic acid after 30 h, with a conversion yield of 63 % (w/w) and a productivity of 1.3 g l^?1 h^?1 under the optimized conditions, whereas induced cells produced 51 g l^?1 γ-dodecalactone from 60 g l^?1 10-hydroxystearic acid after 30 h, with a conversion yield of 85 % (w/w) and a productivity of 1.7 g l^?1 h^?1. The conversion yield and productivity of induced cells were 22 % and 1.3-fold higher, respectively, than those of non-induced cells. Induced cells also produced 28 g l^?1 γ-decalactone and 12 g l^?1 γ-butyrolactone from 60 g l^?1 12-hydroxystearic acid and 60 g l^?1 10-hydroxydecanoic acid, respectively, after 30 h. The concentration, conversion yield, and productivity of γ-dodecalactone and γ-decalactone are the highest reported thus far. This is the first study on the biotechnological production of γ-butyrolactone.     

Control and optimization of nitrifying communities for nitritation from domestic wastewater at room temperatures

To achieve nitritation from complete-nitrification seed sludge at room temperature of 19 ± 1 °C, a lab-scale sequencing batch reactor (SBR) treating domestic wastewater with low C/N ratios was operated to investigate the control and optimization of nitrifying communities. Ammonia oxidizing bacteria (AOB) dominance was enhanced through the combination of low DO concentrations (<1.0 mg/L) and preset short-cycle control of aeration time. Nitritation was successfully established with NO₂^?-N/NO_x^?-N over 95%. To avoid the adverse impact of low DO concentrations on AOB activities, DO concentrations were increased to 1–2 mg/L. At the normal DO levels and temperatures, on-line control strategy of aerobic durations maintained the stability of nitritation with nitrite accumulation rate over 95% and ammonia removal above 97%. Fluorescence in-situ hybridization (FISH) analysis presented that the maximal percentage of AOB in biomass reached 10.9% and nitrite oxidizing bacteria (NOB) were washed out.     

Nisin A and Polymyxin B as Synergistic Inhibitors of Gram-positive and Gram-negative Bacteria

Nisin A and polymyxin B were tested alone and in combination in order to test their antagonism against Listeria innocua HPB13 and Escherichia coli RR1, respectively. While the combination of both antibacterial substances was synergistically active against both target bacteria, nisin A alone did not show any inhibition of E. coli RR1. The nisin A/polymyxin B combination at 1.56/2.5 μg ml^?1 caused lysis of about 35.86 ± 0.35 and 73.36 ± 0.14% of L. innocua HPB13 cells after 3 and 18 h, respectively. Polymyxin B at 0.12 μg ml^?1 and nisin A/polymyxin B at 4.64/0.12 μg ml^?1 decreased the numbers of viable E. coli RR1 cells by about 0.23 and 0.65 log₁₀ CFU ml^?1, respectively, compared to the control. Our data suggest that the concentration of nisin A required for the effective control of pathogenic strains Listeria spp. could be lowered considerably by combination with polymyxin B. The use of lower concentrations of nisin A or polymyxin B should slow the emergence of bacterial populations resistant to these agents.     

Microbial lipid production: screening with yeasts grown on Brazilian molasses

Rhodotorula glutinis CCT 2182, Rhodosporidium toruloides CCT 0783, Rhodotorula minuta CCT 1751 and Lipomyces starkeyi DSM 70296 were evaluated for the conversion of sugars from Brazilian molasses into single-cell oil (SCO) feedstock for biodiesel. Pulsed fed-batch fermentations were performed in 1.65 l working volume bioreactors. The maximum specific growth rate (µ_max), lipid productivity (Pr) and cellular lipid content were, respectively, 0.23 h^?1, 0.41 g l^?1 h^?1, and 41 % for Rsp. toruloides; 0.20 h^?1, 0.27 g l^?1 h^?1, and 36 % for Rta. glutinis; 0.115 h^?1, 0.135 g l^?1 h^?1, and 27 % for Rta. minuta; and 0.11 h^?1, 0.13 g l^?1 h^?1, and 32 % for L. starkeyi. Based on their microbial lipid productivity, content, and profile, Rsp. toruloides and Rta. glutinis are promising candidates for biodiesel production from Brazilian molasses. All the oils from the yeasts were similar to the composition of plant oils (rapeseed and soybean) and could be used as raw material for biofuels, as well as in food and nutraceutical products.     

Enhanced efficacy of nitrifying biomass by modified PVA_SB entrapment technique

In this study, we developed a novel technique for preparing polyvinyl alcohol (PVA) hydrogel as an immobilizing matrix by the addition of sodium bicarbonate. This resulted in an increase in the specific surface area of PVA_sodium bicarbonate (PVA_SB) hydrogel beads to 65.23 m² g^?1 hydrogel beads, which was approximately 85 and 14 % higher than those of normal PVA and PVA_sodium alginate (PVA_SA) hydrogel beads, respectively. The D _e value of PVA_SB hydrogel beads was calculated as 7.49 × 10^?4 cm² s^?1, which was similar to the D _e of PVA_SA hydrogel beads but nearly 38 % higher than that of the normal PVA hydrogel beads. After immobilization with nitrifying biomass, the oxygen uptake rate and the ammonium oxidation rate of nitrifying biomass entrapped in PVA_SB hydrogel beads were determined to be 19.53 mg O₂ g MLVSS^?1 h^?1 and 10.59 mg N g MLVSS^?1 h^?1, which were 49 and 43 % higher than those of normal PVA hydrogel beads, respectively. Scanning electron microscopy observation of the PVA_SB hydrogel beads demonstrated relatively higher specific surface area and revealed loose microstructure that was considered to provide large spaces for microbial growth. This kind of structure was also considered beneficial for reducing mass transfer resistance and increasing pollutant uptake.