Comparative investigation of the use of various commercial microcarriers as a substrate for culturing mammalian cells

Microcarriers provide large adhesion area allowing high cell densities in bioreactor systems. This study focused on the investigation of cell adhesion and cell growth characteristics of both anchorage-dependent CHO-K1 and anchorage-independent Ag8 myeloma cell lines cultivated on four different microcarriers (Biosilon®, Microhex®, Cytodex 3®, Cytoline 2®) by considering the cell kinetics and physiological data. Experiments were performed in both static and agitated cell culture systems by using 24-well tissue culture plates and then 50-ml spinner flasks. In agitated cultures, the highest specific growth rates (0.026 h for CHO-K1 and 0.061 h for Ag8 cell line) were obtained with Cytodex 3® and Cytoline 2® microcarriers for CHO-K1 and Ag8 cell line, respectively. Metabolic characteristics showed some variation among the cultures with the four microcarriers. The most significant being the higher production of lactate with microcarriers with CHO-K1 cells relative to the Ag8 cells. SEM analyses revealed the differences in the morphology of the cells along with microcarriers. On Cytodex 3® and Cytoline 2®, CHO-K1 cells attached to the substratum through long, slender filopodia, whereas the cells showed a flat morphology by covering the substratum on the Biosilon® and Microhex®. Ag8 cells maintained their spherical shapes throughout the culture for all types of microcarriers. In an attempt to scale-up, productions were carried out in 50-ml spinner flasks. Cytodex 3® (for CHO-K1 cells) and Cytoline 2® (for Ag8 cells) were evaluated. The results demonstrate that high yield of biomass could be achieved through the immobilization of the cells in each culture system. And cell cultures on microcarriers, especially on Cytodex 3® and Cytoline 2®, represented a good potential as microcarriers for larger scale cultures of CHO-K1 and Ag8, respectively. Moreover, owing to the fact that the cell lines and culture media are specific, outcomes will be applicable for other clones derived from the same host cell lines.     

Optimization of physical parameters for cell attachment and growth on macroporous microcarriers

The rates of cell attachment of the anchorage-dependent mammalian cell line Vero to the gelatin-based macroporous microcarrier Cultispher-G were determined under various conditions. An optimal rate of attachment (0.98 x 10(-2) min(-1)) occurred by an intermittent stirring regimen of 3 min stirring at 40 rpm per 33 min. This stirring regimen appeared to maximize cell-to-bead attachment and minimized cell aggregation which occurred at a broadly comparable rate.A further increase in the rate of cell-to-bead attachment occurred by preincubation of the microcarriers in serum-supplemented medium prior to cell inoculation in a serum-free medium. However, serum supplementation (>5%) was required for maximal cell growth. The pH of the medium had little effect on cell attachment over a broad range (pH 7.1-8.0). An initial cell/bead inoculum of 30 ensured an even distribution of cells on the available microcarriers with a low proportion of unoccupied beads.The rate of cell attachment to Cultispher-G was an order of magnitude lower than the determined value for the charged dextran microcarrier Cytodex-1, which was measured as 9.05 x 10(-2) min(-1). The optimal conditions for cell attachment were significantly different for the two bead types. Cell attachment to the electrostatic surface of the Cytodex-1 microcarriers was highly dependent on pH and serum supplementation. Cell aggregation during attachment to the Cytodex-1 microcarriers was minimal because of the higher rate of cell-microcarrier attachment.The porous nature of the Cultispher-G microcarriers allowed a maximum cell/bead loading of >1400, which was at least 3 times higher than equivalent loading of the cells on Cytodex-1. The Cultispher-G matrix also allowed the use of higher agitation rates (up to 100 rpm) in spinner flasks without affecting the cell growth rate or maximum cell density. (c) 1996 John Wiley & Sons, Inc.     

Application of Taguchi’s method in the optimization of bridging efficiency between confluent and fresh microcarriers in bead-to-bead transfer of Vero cells

Taguchi’s L8 experimental design was firstly applied to identify critical parameters affecting the efficiency of bridge formation between confluent and fresh microcarriers in bead-to-bead transfer of Vero cells. Statistical analysis indicated that stirring time, rest time and the interactions between stirring time and rest time, stirring speed and rest time had significant effects. Subsequently, a two-stage cell transfer process was performed successfully, in which an efficiency of bridge formation (15.3 ± 1.7%) obtained from 8 h intermittent agitation made percentage of bare microcarriers decrease quickly from 66.7% to 2.0 ± 0.8%.     

Growth of human vascular endothelial cells on various types of microcarriers

Various types of microcarriers were tested as growth substrate for the cultivation of either endothelial cells from human umbilical cord veins or of EA. hy926, an immortalized cell line of endothelial origin. Cell growth was tested on microcarriers in tissue culture flasks and spinner flasks. Solid (Cytodex type I, II, III, Gelibeads, Mica) and macroporous (Polyhipe, CultiSpher GL, PolyporE type I) microcarriers were tested. For the solid carriers the best results were obtained with Mica and for the macroporous carriers with CultiSpher GL.Abbreviations DAPI 4,6-diamidino-2-phenylindole-di-hydrochloride - DEAE diethylaminoethyl - EC vascular endothelial cells - FGF fibroblast growth factor - HUVEC vascular endothelial cells from human umbilical cord veins - IF 11 mixture of Iscove's MDM and F12 basal media - NCS newborn calf serum - PBS phosphate buffered saline - TE 0.05% (w/v) trypsin, 0.02% (w/v) EDTA in PBS     

Scale-up of mouse embryonic stem cell expansion in stirred bioreactors

The aim of this study was to develop a robust, quality controlled and reproducible large-scale culture system using serum-free (SF) medium to obtain vast numbers of embryonic stem (ES) cells as a starting source for potential applications in tissue regeneration, as well as for drug screening studies. Mouse ES (mES) cells were firstly cultured on microcarriers in spinner flasks to investigate the effect of different parameters such as the agitation rate and the feeding regimen. Cells were successfully expanded at agitation rates up to 60 rpm using the SF medium and no significant differences in terms of growth kinetics or metabolic profiles were found between the two feeding regimens evaluated: 50% medium renewal every 24 h or 25% every 12 h. Overall, cells reached maximum concentrations of (4.2 ± 0.4) and (5.6 ± 0.8) ×10(6) cells/mL at Day 8 for cells fed once or twice per day; which corresponds to an increase in total cell number of 85 ± 7 and 108 ± 16, respectively. To have a more precise control over culture conditions and to yield a higher number of cells, the scale-up of the spinner flask culture system was successfully accomplished by using a fully controlled stirred tank bioreactor. In this case, the concentration of mES cells cultured on microcarriers increased 85 ± 15-fold over 11 days. Importantly, mES cells expanded under stirred conditions, in both spinner flask and fully controlled stirred tank bioreactor, using SF medium, retained the expression of pluripotency markers such as Oct-4, Nanog, and SSEA-1 and their differentiation potential into cells of the three embryonic germ layers.     

Comparisons of microcarrier cell culture processes in one hundred mini-liter spinner flask and fifteen-liter bioreactor cultures

Microcarrier cell culture process can be used to culture anchorange-dependent cells in large bioreactor vessels. The process performance in large bioreactors is usually less prominent than that in spinner flask vessels and bench scale reactors. In this study we investigated the microcarrier cell culture processes in 100?ml spinner flask and 15-liter bioreactor cultures, including the kinetics for cell attachment, cell growth and the production of Japanese encephaltilis vaccine strain (Beijing-1) virus. Under a fixed concentration of microcarrier and cell density used in inoculations, the attachment kinetics of Vero cells on Cytodex 1 microcarrier in a 15-liter bioreactor vessel was 2 folds slower than with 100?ml spinner flask culture. Virus replication in 15-liter bioreactor culture also revealed an approximately one day lag-time compared to 100?ml spinner flask culture. Findings presented herein provide valuable information for designing and operating microcarrier cell culture processes in large bioreactor vessels.     

人皮肤成纤维细胞在不同培养系统中的生长代谢特性

大面积烧伤病人及多种皮肤溃疡病人很难用自体皮肤移植来进行治疗.早期治疗方法采用尸体来源的皮肤移植,但由于来源有限、且有传播疾病的危险,因此应用组织工程技术构建生物活性人工皮肤已成为近十几年来在组织工程和创伤治疗领域的研究热点,目前已有几种人工皮肤成功地走向临床[1].然而,在构建大面积皮肤组织过程中,如何大量制备皮肤种子细胞仍然是一大棘手的难题,成为人体皮肤组织工程迫切需要解决的技术关键.获得大量扩增的皮肤细胞,解决种子细胞的供应问题,是构建人工皮肤的一个关键.     

Hybridoma cell growth and anti-neuroblastoma monoclonal antibody production in spinner flasks using a protein-free medium with microcarriers

The main disadvantages of foetal calf serum as the world-wide common serum supplement for cell growth are its content of various proteins of variable concentrations between batches as well as its high cost. The use of serum-free and protein-free media is gradually becoming one of the goals of cell culture especially for standardizing culture conditions or for simple purification of cell products like monoclonal antibodies. The mouse hybridoma cells 14/2/1 were cultivated either in protein-free UltraDOMA medium or in serum-containing RPMI medium with and without microcarriers to generate high quantities of monoclonal antibodies against neuroblastoma tumour cells. Cell growth rate, IgG production, viability, glucose and lactate concentrations, attachment rate and doubling time have been used as investigation criteria. Modifications of culture procedures (static or stirred), inoculum density, and microcarrier concentration caused an improvement of monoclonal antibody production. The kinetics of antibody synthesis was best in spinner culture with 2 ml of microcarriers in protein-free medium. These results of short-term microcarrier culture in stirred spinner flasks indicate that IgG yields in protein-free medium 2.5-fold higher to those in serum-supplemented medium can be achieved.     

Influence of intermittent pressure, fluid flow, and mixing on the regenerative properties of articular chondrocytes.

Equine articular chondrocytes, embedded within a polyglycolic acid nonwoven mesh, were cultured with various combinations of intermittent pressure, fluid flow, and mixing to examine the effects of different physical stimuli on neochondrogenesis from young cells. The cell/polymer constructs were cultured first in 125 ml spinner flasks for 1, 2, or 4 weeks and then in a perfusion system with intermittent pressure for a total of up to 6 weeks. Additional constructs were either cultured for all 6 weeks in the spinner flasks or for 1 week in spinners followed by 5 weeks in the perfusion system without intermittent pressure. Tissue constructs cultivated for 2 or 4 weeks in spinner flasks followed by perfusion with intermittent pressure had significantly higher concentrations of both sulfated glycosaminoglycan and collagen than constructs cultured entirely in spinners or almost entirely in the pressure/perfusion system. Initial cultivation in the spinner flasks, with turbulent mixing, enhanced both cell attachment and early development of the extracellular matrix. Subsequent culture with perfusion and intermittent pressure appeared to accelerate matrix formation. While the correlation was much stronger in the pressurized constructs, the compressive modulus was directly proportional to the concentration of sulfated glycosaminoglycan in all physically stressed constructs. Constructs that were not stressed beyond the 1-week seeding period lost mechanical integrity upon harvest, suggesting that physical stimulation, particularly with intermittent pressure, of immature tissue constructs during their development may contribute to their ultimate biomechanical functionality.     

Effects of oxygen on recombinant protein production by suspension cultures of Spodoptera frugiperda (Sf-9) insect cells.

Spodoptera frugiperda (Sf-9) insect cells have been grown in serum-free medium in 250-ml spinner flasks. The maximum cell density obtained in these cultures was dependent on the aeration rate of the culture. Similar yields of uninfected cells were obtained when cultures were stirred in spinner flasks at 80 rev min-1 and in a 4-1 stirred-tank bioreactor and the dissolved oxygen in the bioreactor was controlled at 20% of air saturation. Cells were infected with a recombinant baculovirus at different multiplicities of infection: the timing and maximum level of expression of the recombinant protein were dependent on the multiplicity of infection, the cell density at infection, and on the aeration rate of the culture. Oxygen-limited growth resulted in undetectable levels of recombinant protein (< 6 ng recombinant protein 10(-7) cells). Compared with the maximum yields observed in spinner flask cultures, higher levels of recombinant protein were produced when cells were grown and infected in the bioreactor. The level of dissolved oxygen in the bioreactor was controlled at 50% of air saturation.     

WAVETM反应器和搅拌瓶中微载体球转球放大培养的比较

目的:哺乳动物细胞目前已广泛用于生物工程药物如单抗和疫苗的生产.而用于贴壁细胞规模化培养的微载体,也应时应需得以开发并应用于生物制药.贴壁细胞微载体培养在搅拌罐和WAVETM反应器中都能进行.而如要进行进一步的放大培养,球转球工艺不可或缺.为了发展球转球这一新的放大技术,以及考量WAVETM反应器这种新型大规模培养设备的应用性,大量的细胞培养和球转球实验在WAVETM反应器和搅拌瓶中进行.收集到的数据得以分析比较.方法:将Vero细胞分别接入WAVETM反应器和搅拌瓶中用微载体Cytodex 1进行培养.适当补充营养并控制温度、pH等培养条件使细胞增殖.长满微载体的细胞用清洗、消化等球转球工艺的一系列步骤而分离,并放大接种到新的培养体系.球转球工艺的有效性通过记录并统计分析细胞消化分离的回收率,以及细胞重新接种生长的存活力来评估.结果:统计学分析比较WAVETM反应器和搅拌瓶中得到的细胞分离回收率分别是67.56％和39.39％,数理统计P值小于0.0003;细胞重新接种存活率分别是95.17％和78.45％,P值等于0.0107.结论:在WAVETM反应器中进行的球转球放大工艺,其总体表现和有效性远高于在搅拌瓶中得到的结果.在WAVETM反应器中培养的Vero细胞有很好的细胞状态,作为种子链和生产用罐相比搅拌型反应罐均有很大的优越性.     

On line estimation of oxygen uptake rate for insect cells growing in a modified spinner flask

The simple design of traditional spinner flasks makes the on-line estimation of cellular metabolism impossible. An on-line estimation system has been developed and used for the monitoring of oxygen uptake rate (OUR) for insect cells growing in a modified spinner flask. Neglect of oxygen desorption from culture media is a common source of error in OUR measurements for Sf21 cells. Therefore, an algorithm was developed to compensate for the affect of such desorption process on the determination of OUR. A modified spinner flask was successfully used as a low-volume bioreactor for insect cell cultivation and the OUR measurement developed here is both convenient and reliable.     

On-line monitoring of oxygen in Tubespin, a novel, small-scale disposable bioreactor

A novel, optical sensor was fixed in a new type of disposable bioreactor, Tubespin, for the on-line (real-time) monitoring of dissolved oxygen concentrations during cell culture. The cell density, viability and volumetric mass transfer coefficient were also determined to further characterize the bioreactors. The k_La value of the Tubespin at standard conditions was 24.3 h⁻¹, while that of a spinner flask was only 2.7 h⁻¹. The maximum cell density in the Tubespin bioreactor reached 6 × 10⁶ cells mL⁻¹, which was two times higher than the cell density in a spinner flask. Furthermore, the dynamic dissolved oxygen level was maintained above 90% air-saturation in the Tubespin, while the value was only 1.9% in a spinner flask. These results demonstrate the competitive advantage of using the Tubespin system over spinner flasks for process optimization and scale-down studies of oxygen transfer and cell growth.     

HeLa cell adhesion to microcarriers in high shear conditions: evidence for membrane receptors for collagen but not laminin or fibronectin

HeLa-S3 cells were analyzed for their ability to attach and spread on cell culture microcarriers that were made either positively or negatively charged with polymeric plastics or were coated with BSA, gelatin, fibronectin or laminin. The cells stuck to all microcarriers under low shear, i.e. low stirring conditions with similar rates of attachment. Except in the case of gelatin microcarriers where cells fully spread, cells did not or only partially spread on the others. Under high shear, cells attached with the following rates: positive = negative = gelatin = BSA greater than laminin greater than fibronectin. Cells detached from all but the gelatin and BSA coated beads. However, the cells did not fully spread on BSA beads. The observation that cells not only attached but also spread on gelatin beads indicated that gelatin could be a specific substratum adhesion protein while the other surfaces were 'non-specific'. It should be noted that neither antibodies to laminin nor fibronectin interfered with attachment to gelatin. Protein synthesis inhibitors reduced the attachment and spreading on gelatin beads under high but not low shear conditions. With low shear, attachment and spreading appeared normal. We concluded that the density of the cell surface attachment proteins was reduced by the protein synthesis inhibitors and there were not enough present to facilitate attachment under high shear. The results also indicated that protein synthesis was not essential for cell spreading. Proteolysis of the cell surface with low concentrations of trypsin abolished the attachment of cells to gelatin-coated beads. The reappearance of attachment ability took several hours and was inhibited by actinomycin-D.     

Cultivation of immortalized human hepatocytes HepZ on macroporous CultiSpher G microcarriers

Cultivation of the new immortalized hepatocyte cell line HepZ was performed with a 1:1 mixture of DMEM and Ham's F12 media containing 5% FCS. The cells were grown in their 40th passage in 100 mL and 1 L volumes in spinner flasks and in a bioreactor, respectively. For the production of adherently growing HepZ cells macroporous CultiSpher G gelatin microcarriers were used in various concentrations from 1 to 3 g/L. The cells were seeded in a density of 2 x 10(5) cells/mL when using a microcarrier concentration of 1 g/L and 5 x 10(5) cells/mL at a microcarrier concentration of 3 g/L. After 7 days of cultivation a maximum cell concentration of 4.5 x 10(6) cells/mL was obtained in the spinner culture using a microcarrier concentration of 1 g/L. With bubble-free aeration and daily medium exchange from day 7, 7.1 x 10(6) cells/mL were achieved in the bioreactor using a microcarrier concentration of 3 g/L. The cells exhibited a maximum specific growth rate of 0.84 per day in the spinner system and 1.0 per day in the bioreactor, respectively. During the growth phase the lactate dehydrogenase (LDH) activity rose slightly up to values of 200 U/L. At the end of cultivation the macroporous carriers were completely filled with cells exhibiting a spherical morphology whereas the hepatocytes on the outer surface were flat-shaped. Concerning their metabolic activity the cells predominantly consumed glutamine and glucose. During the growth phase lactate was produced up to 19.3 mM in the spinner culture and up to 9.1 mM in the bioreactor. Maximal oxygen consumption was 1950 nmol/(10(6) cells. day). HepZ cells resisted a 4-day long chilling period at 9.5 degrees C. The cytochrome P450 system was challenged with a pulse of 7 microgram/mL lidocaine at a cell density of 4.5 x 10(6) cells/mL. Five ng/mL monoethylglycinexylidide (MEGX) was generated within 1 day without phenobarbital induction compared to 26 ng/mL after a preceded three day induction period with 50 microgram/mL of phenobarbital indicating hepatic potency. Thus, the new immortalized HepZ cell line, exhibiting primary metabolic functions and appropriate for a mass cell cultivation, suggests its application for a bioartificial liver support system.     

Microcarrier cultivation of bovine aortic endothelial cells in spinner vessels and a membrane stirred bioreactor

Primary bovine aortic endothelial cells were cultivated in serum supplemented medium without any additional growth factors. The anchorage dependent cells were propagated on Dormacell^® microcarriers with covalently bound dimeric DEAE-groups at the surface of the dextrane beads. Cultivations were performed in 200 ml spinner cultures containing 1 g l^–1 to 3 g l^–1 of microcarriers. Out of five types of Dormacell^® microcarriers with different ion exchange capacities ranging from 0.30 up to 0.65 meq g^–1, corresponding to nitrogen contents from 1.2% to 2.9%, respectively, optimal attachment and growth of endothelial cells were obtained with beads of highest nitrogen content (2.9%). Cells were seeded withca. 5 viable cells per microcarrier being sufficient to achieve fully confluent microcarriers after 4 to 5 days. Glucose concentrations decreased from 21 mM to uppermost half of the original concentrations. 4 mM glutamine was rapidly consumed and virtually exhausted after the cells reached confluency. Lactate concentrations raised to a maximum of 7 mM in spinner cultures, but was found to be reutilized in the stationary phase after glutamine limitation occurred. Serine was found to be the second most prominent amino acid being almost exhausted at confluency whereas alanine was produced in noteworthy amounts. Considerable decrease was determined for threonine, lysine and arginine; low consumption rates were observed for leucine, phenylalanine and methionine. All other amino acids did not alter significantly throughout cultivation. These data support that bovine aortic endothelial cells are capable to utilize glucose and glutamine as well as lactic acid (after glutamine exhaustion) as energy and/or carbon source. Finally, batch cultures in a 2 liter membrane stirred bioreactor with bubble-free aeration were performed to produce large quantities of endothelial cells using microcarrier concentrations of 3 g l^–1.Abbreviations BAE cells bovine aortic endothelial cells - NCS newborn calf serum - PBS phosphate buffered saline     

Improvement of a fixed bed bioreactor for plant cell culture

A bioreactor used for cultivation of microbes entrapped in beads was utilized for batch culture of tobacco cells. Tobacco cells were tightly fixed on the cell-attachment net and growth rates of the cells were similar in both the bioreactor and flasks. Furthermore, there was no significant difference in the intracellular biosynthesis of phenylpropanoids between the bioreactor and flask cultures.     

Cell Culture conditions determine the enhancement of specific monoclonal antibody productivity of calcium alginate-entrapped S3H5/gamma2bA2 hybridoma cells

Immobilization offers several intrinsic advantages over free suspension cultures for the production of monoclonal antibodies. An important advantage of immobilization is the improved specific monoclonal antibody (MAb) productivity (q(MAb)) that can be obtained. However, there are conflicting reports in the literature on the enhancement of the q(MAb) with immobilization. The discrepancies between these reports can be attributed to the different to either the cultivation methods used for immobilized cell or to difference between the cell lines used in the various studies. We show that these differences may be attributed to the different cultivation methods used for one model hybridoma cell line. S3H5/Upsilon2bA2 hybridoma cells entrapped in different sizes of calcium alginate beads were cultivated in both T- and spinner flasks in order to determine whether cultivation methods (T- and spinner flasks) and bead size influence the q(MAb) Free-suspended cell cultures inoculated with cells recovered from alginate beads were also carried out in order to determine whether changes in the q(Mab) of the entrapped cells are reversible.The cultivation methods was found to influence significantly the q(MAb) of the entrapped cells. When the entrapped cells in 1-mn diameter beads were cultivated in T-flasks, the q(MAb) was not increased by 200% as previously observed in an entrapped cell culture using 1-mm-diameter alginate beads in spinner flasks. The q(MAb) of the entrapped cell was approximately 58% higher than that of the free-suspended cells in a control experiment. Unlike the cultivation method, the bead size in the range of 1- to 3-mm diameter did not significantly influence the q(MAb), regardless of cultivations methods. The changes in q(MAb) of an entrapped cells were reversible. When the free-suspended cells recovered from the T- and spinner flasks were sub-cultured in T- and spinner flasks enhanced q(MAb) of the entrapped cells in both cases decreased to the level of the free-suspended cell in a control experiments. Taken together, these results shows that the method of cultivation of hybridoma cells immobilized in alginate beads determines the extent of enhancement of the q(MAb). (c) 1993 John Wiley & Sons, Inc.     

Fabrication of viable and functional pre‐vascularized modular bone tissues by coculturing MSCs and HUVECs on microcarriers in spinner flasks

Slow vascularization often impedes the viability and function of engineered bone replacements. Prevascularization is a promising way to solve this problem. In this study, a new process was developed by integrating microcarrier culture and coculture to fabricate pre‐vascularized bone microtissues with mesenchymal stem cells (MSCs) and human umbilical vein endothelial cells (HUVECs). Initially, coculture medium and cell ratio between MSCs and HUVECs were optimized in tissue culture plates concerning cell proliferation, osteogenesis and angiogenesis. Subsequently, cells were seeded onto CultiSpher S microcarriers in spinner flasks and subjected to a two‐stage (proliferative‐osteogenic) culture process for four weeks. Both cells proliferated and functioned well in chosen medium and a 1 : 1 ratio between MSCs and HUVECs was chosen for better angiogenesis. After four weeks of culture in spinner flasks, the microtissues were formed with high cellularity, evenly distributed cells and tube formation ability. While coculture with HUVECs exerted an inhibitory effect on osteogenic differentiation of MSCs, with downregulated alkaline phosphatase activity, mineralization and gene expression of COLI, RUNX2 and OCN, this could be attenuated by employing a delayed seeding strategy of HUVECs against MSCs during the microtissue fabrication process. Conclusion: Collectively, this work established an effective method to fabricate pre‐vascularized bone microtissues, which would lay a solid foundation for subsequent development of vascularized tissue grafts for bone regeneration.     

Expansion of human mesenchymal stem cells on microcarriers

The effects on human mesenchymal stem cell growth of choosing either of two spinner flask impeller geometries, two microcarrier concentrations and two cell concentrations (seeding densities) were investigated. Cytodex 3 microcarriers were not damaged when held at the minimum speed, N_JS, for their suspension, using either impeller, nor was there any observable damage to the cells. The maximum cell density was achieved after 8–10 days of culture with up to a 20-fold expansion in terms of cells per microcarrier. An increase in microcarrier concentration or seeding density generally had a deleterious or neutral effect, as previously observed for human fibroblast cultures. The choice of impeller was significant, as was incorporation of a 1 day delay before agitation to allow initial attachment of cells. The best conditions for cell expansion on the microcarriers in the flasks were 3,000 microcarriers ml⁻¹ (ca. 1 g dry weight l⁻¹), a seeding density of 5 cells per microcarrier with a 1 day delay before agitation began at N_JS (30 rpm), using a horizontally suspended flea impeller with an added vertical paddle. These findings were interpreted using Kolmogorov’s theory of isotropic turbulence.