Rapid agarose gel electrophoretic mobility shift assay for quantitating protein: RNA interactions

Interactions between proteins and nucleic acids are frequently analyzed using electrophoretic mobility shift assays (EMSAs). This technique separates bound protein:nucleic acid complexes from free nucleic acids by electrophoresis, most commonly using polyacrylamide gels. The current study utilizes recent advances in agarose gel electrophoresis technology to develop a new EMSA protocol that is simpler and faster than traditional polyacrylamide methods. Agarose gels are normally run at low voltages (∼10 V/cm) to minimize heating and gel artifacts. In this study we demonstrate that EMSAs performed using agarose gels can be run at high voltages (≥20 V/cm) with 0.5 × TB (Tris-borate) buffer, allowing for short run times while simultaneously yielding high band resolution. Several parameters affecting band and image quality were optimized for the procedure, including gel thickness, agarose percentage, and applied voltage. Association of the siRNA-binding protein p19 with its target RNA was investigated using the new system. The agarose gel and conventional polyacrylamide gel methods generated similar apparent binding constants in side-by-side experiments. A particular advantage of the new approach described here is that the short run times (5–10 min) reduce opportunities for dissociation of bound complexes, an important concern in non-equilibrium nucleic acid binding experiments.     

Agarose and polyacrylamide gel electrophoresis methods for molecular mass analysis of 5- to 500-kDa hyaluronan

Agarose and polyacrylamide gel electrophoresis systems for the molecular mass-dependent separation of hyaluronan (HA) in the size range of approximately 5–500 kDa were investigated. For agarose-based systems, the suitability of different agarose types, agarose concentrations, and buffer systems was determined. Using chemoenzymatically synthesized HA standards of low polydispersity, the molecular mass range was determined for each gel composition over which the relationship between HA mobility and logarithm of the molecular mass was linear. Excellent linear calibration was obtained for HA molecular mass as low as approximately 9 kDa in agarose gels. For higher resolution separation, and for extension to molecular masses as low as approximately 5 kDa, gradient polyacrylamide gels were superior. Densitometric scanning of stained gels allowed analysis of the range of molecular masses present in a sample as well as calculation of weight-average and number-average values. The methods were validated for polydisperse HA samples with viscosity-average molecular masses of 112, 59, 37, and 22 kDa at sample loads of 0.5 μg (for polyacrylamide) to 2.5 μg (for agarose). Use of the methods for electrophoretic mobility shift assays was demonstrated for binding of the HA-binding region of aggrecan (recombinant human aggrecan G1–IGD–G2 domains) to a 150-kDa HA standard.     

Modification of gel architecture and TBE/TAE buffer composition to minimize heating during agarose gel electrophoresis

Agarose gel electrophoresis of DNA and RNA is routinely performed using buffers containing either Tris, acetate, and EDTA (TAE) or Tris, borate, and EDTA (TBE). Gels are run at a low, constant voltage (∼10 V/cm) to minimize current and asymmetric heating effects, which can induce band artifacts and poor resolution. In this study, alterations of gel structure and conductive media composition were analyzed to identify factors causing higher electrical currents during horizontal slab gel electrophoresis. Current was reduced when thinner gels and smaller chamber buffer volumes were used, but was not influenced by agarose concentration or the presence of ethidium bromide. Current was strongly dependent on the amount and type of EDTA used and on the concentrations of the major acid–base components of each buffer. Interestingly, resolution and the mobilities of circular versus linear plasmid DNAs were also affected by the chemical form and amount of EDTA. With appropriate modifications to gel structure and buffer constituents, electrophoresis could be performed at high voltages (20–25 V/cm), reducing run times by up to 3-fold. The most striking improvements were observed with small DNAs and RNAs (10–100 bp): high voltages and short run times produced sharper bands and higher resolution.     

Two-dimensional gel electrophoresis image registration using block-matching techniques and deformation models

Block-matching techniques have been widely used in the task of estimating displacement in medical images, and they represent the best approach in scenes with deformable structures such as tissues, fluids, and gels. In this article, a new iterative block-matching technique—based on successive deformation, search, fitting, filtering, and interpolation stages—is proposed to measure elastic displacements in two-dimensional polyacrylamide gel electrophoresis (2D–PAGE) images. The proposed technique uses different deformation models in the task of correlating proteins in real 2D electrophoresis gel images, obtaining an accuracy of 96.6% and improving the results obtained with other techniques. This technique represents a general solution, being easy to adapt to different 2D deformable cases and providing an experimental reference for block-matching algorithms.     

Electrophoretic transfer protein zymography

Zymography detects and characterizes proteolytic enzymes by electrophoresis of protease-containing samples into a nonreducing sodium dodecyl sulfate–polyacrylamide gel electrophoresis (SDS–PAGE) gel containing a copolymerized protein substrate. The usefulness of zymography for molecular weight determination and proteomic analysis is hampered by the fact that some proteases exhibit slower migration through a gel that contains substrate protein. This article introduces electrophoretic transfer protein zymography as one solution to this problem. In this technique, samples containing proteolytic enzymes are first resolved in nonreducing SDS–PAGE on a gel without protein substrate. The proteins in the resolving gel are then electrophoretically transferred to a receiving gel previously prepared with a copolymerized protein substrate. The receiving gel is then developed as a zymogram to visualize clear or lightly stained bands in a dark background. Band intensities are linearly related to the amount of protease, extending the usefulness of the technique so long as conditions for transfer and development of the zymogram are kept constant. Conditions of transfer, such as the pore sizes of resolving and receiving gels and the transfer time relative to the molecular weight of the protease, are explored.     

Toward a high resolution 2-DE profile of the normal human liver proteome using ultra-zoom gels

The human liver is the largest organ in the body and has many important physiological functions. A global analysis of human liver proteins is essential for a better understanding of the molecular basis of the normal functions of the liver and of its diseases. As part of the Human Liver Proteome Project (HLPP), the goal of the present study was to visualize and detect as many proteins as possible in normal human livers using two-dimensional gel electrophoresis (2-DE). We have constructed a reference map of the proteins of human normal liver that can be used for the comprehensive analysis of the human liver proteome and other related research. To improve the resolution and enhance the detection of low abundance proteins, we developed and optimized narrow pH range ultra-zoom 2-DE gels. High resolution patterns of human liver in pH gradients 4.5–5.5, 5–6, 5.5–6.7, 6–9 and 6–11 are presented. To improve the poor resolution in the alkaline pH range of 2-DE gels, we optimized the isoelectric focusing protocol by including sample application using cup loading at the anode and incorporating 1.2% hydroxyethyl disulfide, 15% 2-propanol and 5% glycerol in the rehydration buffer. Using the optimized protocol, we obtained reproducibly better resolution in both analytical and preparative 2-DE gels. Compared with the 2386 and 1878 protein spots resolved in the wide range 3–10 and 4–7 pH gradients respectively, we obtained 5481 protein spots from the multiple (overlapping) narrow pH range ultra-zoom gels in the range of pH 4.5–9. The visualized reference map of normal human liver proteins presented in this paper will be valuable for comparative proteomic research of the liver proteome.     

Improvements in polyacrylamide gel slicing

An improved polyacrylamide gel slicer has been devised that provides rapid uniform slicing with a precision of 4–6%. The advantages of this type of slicer are: The gel is sliced directly from the electrophoresis tube; gel diameter and length can vary with no modification of the system; and gels with a range of acrylamide concentrations can be fractionated with no pretreatment of the gel.     

Highly Selective Acridine and Ethidium Staining of Bacterial DNA and RNA

The acridine dyes acridine orange (AO) and coriphosphine O (CPO) and ethidium bromide (EtBr) were used to stain bacterial digests after electrophoresis in native and denaturing (SDS) polyacrylamide gels and were shown to stain DNA and RNA preferentially over other subcellular components in the gels. Vegetative cell digests of Bacillus subtilis, Escherichia coli, Micrococcus luteus, and Staphylococcus aureus showed intense staining of DNA with AO and CPO near the top of the gel, but little or no staining of other cellular constituents. EtBr stained both DNA and RNA in the gels. Protein standards and non-nucleic acid cellular constituents stained faintly with high concentrations (> 100 μM) of AO, lower concentrations (13.9 μM) of CPO, and did not stain with 0.5 μg/ml EtBr in denaturing gels. The complete set of cellular biochemicals was visualized by silver staining, while the protein subset was detected by Coomassie blue staining. The highest concentrations of AO (120 μM) and CPO (13.9 μM) were shown to detect purified DNA in gels with a sensitivity in the range of 25–50 ng per band. This work demonstrates the specificity of acridine and ethidium dyes for nucleic acids, while illustrating the level of non-nucleic acid-specific interactions with other cellular components by staining of electrophoretically separated cellular components in a gel matrix.     

Sodium dodecyl sulfate-agarose gel electrophoresis for the detection and isolation of amyloid curli fibers

Curli are amyloid-like fibers on the surface of some strains of Escherichia coli and Salmonella enteritidis. We tested the use of horizontal sodium dodecyl sulfate (SDS)–agarose gel electrophoresis to detect, isolate, and quantitate curli. Cell extracts fractionated in SDS–agarose gels and stained with Coomassie blue exhibited a soluble fraction that entered the gel and an insoluble fraction that remained in the well. Much more insoluble material was observed with curli-proficient strains than with strains that do not make curli. Both highly purified curli and the insoluble material isolated from an SDS–agarose gel could be dissociated into monomers when treated with formic acid. For quantitation, we immobilized samples in SDS–agarose prior to electrophoresis. This avoids losses during the staining of the gel. Our methods provide a rapid and simple fractionation of curli using equipment that is readily available.     

Quantitative affinity electrophoresis of RNA–small molecule interactions by cross-linking the ligand to acrylamide

We show that the affinity electrophoresis analysis of RNA–small molecule interactions can be made quantifiable by cross-linking the ligand to the gel matrix. Using an RNA–aminoglycoside model system to verify our method, we attached an acryloyl chloride molecule to the aminoglycosides paromomycin and neomycin B to synthesize an acrylamide–aminoglycoside monomer. This molecule was then used as a component in gel polymerization for affinity electrophoresis, covalently attaching an aminoglycoside molecule to the gel matrix. To test RNA binding to the cross-linked aminoglycosides, we used the aminoglycoside binding RNA molecule derived from thymidylate synthase messenger RNA (mRNA) that contains a C–C mismatch. Binding is indicated by the difference in RNA mobility between gels with cross-linked ligand, with ligand embedded during polymerization, and with no ligand present. Critically, the predicted straight line relationship between the reciprocal of the relative migration of the RNA and the ligand concentration is obtained when using cross-linked aminoglycosides, whereas a straight line is not obtained using embedded aminoglycosides. Average apparent dissociation constants are determined from the slope of the line from these plots. This method allows an easy quantitative comparison between different nucleic acid molecules for a small molecule ligand.     

Transient electric birefringence of agarose gels. I. Unidirectional electric fields

The orientation of agarose gels in pulsed electric fields has been studied by the technique of transient electric birefringence. The unidirectional electric fields ranged from 2 to 20 V/cm in amplitude and 1 to 100 s in duration, values within the range typically used for pulsed field gel electrophoresis (PFGE). Agarose gels varying in concentration from 0.3 to 2.0% agarose were studied. The sign of the birefringence varied randomly from one gel to another, as described previously [J. Stellwagen & N. C. Stellwagen (1989), Nucleic Acids Research, Vol. 17, 1537–1548]. The sign and amplitude of the birefringence also varied randomly at different locations within each gel, indicating that agarose gels contain multiple subdomains that orient independently in the electric field. Three or four relaxation times of alternating sign were observed during the decay of the birefringence. The various relaxation times, which range from 1 to ～ 120 s, can be attributed to hierarchies of aggregates that orient in different directions in the applied electric field. The orienting domains range up to ～ 22 μm in size, depending on the pulsing conditions. The absolute amplitude of the birefringence of the agarose gels increased approximately as the square of the electric field strength. The measured Ker constants are ～ 5 orders of magnitude larger than those observed when short, high-voltage pulses are applied to agarose gels. The increase in the Kerr constants in the low-voltage regime parallels the increase in the relaxation times in low-voltage electric fields. Birefringence saturation saturation curves in both the low- and high-voltage regimes can be fitted by theoretical curves for permanent dipole orientation. The apparent permanent dipole moment increase approximately as the 1.6 power of fiber length, consistent with the presence of overlapping agarose helices in the large fiber bundles orienting in low-voltage electric fields, the optical factor is approximately independent of fiber length. Therefore, the marked increase in the Kerr constants observed in the low-voltage regime is due to the large increase in the electrical orientation factor, which is due in turn to the increased length of the fiber bundles and domains orienting in low-voltage electric fields. Since the size of the fiber bundles and domains approximates the size of the DNA molecules being separated by PFGE, the orientation of the agarose matrix in the applied electric field may facilitate the migration of large DNA molecules during PFGE. © 1994 John Wiley & Sons, Inc.     

Pouring and Running a Protein Gel by reusing Commercial Cassettes

The evaluation of proteins using sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) analysis is a common technique used by biochemistry and molecular biology researchers^1-4. For laboratories that perform daily analyses of proteins, the cost of commercially available polyacrylamide gels (˜$10/gel) can be considerable over time. To mitigate this cost, some researchers prepare their own polyacrylamide gels. Traditional methods of pouring these gels typically utilize specialized equipment and glass gel plates that can be expensive and preclude pouring many gels and storing them for future use. Furthermore, handling of glass plates during cleaning or gel pouring can result in accidental breakage creating a safety hazard, which may preclude their use in undergraduate laboratory classes. Our protocol demonstrates how to pour multiple protein gels simultaneously by recycling Invitrogen Nupage Novex minigel cassettes, and inexpensive materials purchased at a home improvement store. This economical and streamlined method includes a way to store the gels at 4°C for a few weeks. By re-using the plastic gel cassettes from commercially available gels, labs that run frequent protein gels can save significant costs and help the environment. In addition, plastic gel cassettes are extremely resistant to breakage, which makes them ideal for undergraduate laboratory classrooms.     

Au-nanoclusters incorporated 3-amino-5-mercapto-1,2,4-triazole film modified electrode for the simultaneous determination of ascorbic acid, dopamine, uric acid and nitrite

A novel biosensor has been constructed by the electrodeposition of Au-nanoclusters (nano-Au) on poly(3-amino-5-mercapto-1,2,4-triazole) (p-TA) film modified glassy carbon electrode (GCE) and employed for the simultaneous determination of dopamine (DA), ascorbic acid (AA), uric acid (UA) and nitrite (NO₂⁻). NH₂ and SH groups exposed to the p-TA layer are helpful for the electrodeposition of nano-Au. The combination of nano-Au and p-TA endow the biosensor with large surface area, good biological compatibility, electricity and stability, high selectivity and sensitivity and flexible and controllable electrodeposition process. In the fourfold co-existence system, the linear calibration plots for AA, DA, UA and NO₂⁻ were obtained over the range of 2.1–50.1 μM, 0.6–340.0 μM, 1.6–110.0 μM and 15.9–277.0 μM with detection limits of 1.1 × 10⁻⁶ M, 5.0 × 10⁻⁸ M, 8.0 × 10⁻⁸ M and 8.9 × 10⁻⁷ M, respectively. In addition, the modified biosensor was applied to the determination of AA, DA, UA and NO₂⁻ in urine and serum samples by using standard adding method with satisfactory results.     

A gel-sandwich technique for the qualitative and quantitative determination of dehydrogenases in the enzyme histochemistry

Summary A gel-sandwich technique for the histochemical demonstration of dehydrogenases is introduced with LDH set up as an example. Especially suitable, of the gels examined, for this technique is 1.5% W/V agar-agar low gel strength. In it several reaction ingredients for the histochemical reaction are dissolved. Considering LDH the following gel composition showed good results: 1.5% W/V agar-agar low gel strength, 5 mM TNBT in 150 l DMF, 120 mM L-lactate, 3–5 mM NAD⁺, 10 mM amytal, 22,4–32×10^–5 M Meldola Blue, 160 mM soldium phosphate buffer pH 7.6 (total solution of 1 ml). After the solidification of the gel, gel-bars were frozen with CO₂-snow. The 40–80 m thick gel slices were gained in the cryostat. Of the three different arrangement possibilities of the gel slices and the tissue-sections a sandwich arrangement (cover-gel slice — tissue section — ground-gel slice) produced the best results. The enzyme reaction is started by thawing of the gel slices (together with the tissue sections) and by putting them between the hotplate and the evaporator-head-piece, especially developed for this technique. The gel slices also remain in combination with the tissue sections after the reaction.The influence of the gel in combination with the electron carrier Meldola Blue on the spontaneous reduction rates of ditetrazolium salts in day light, were examined as well as the diffusion rates of TNBT and NADH out of gel slices and the influence of DMF and DMSO on the LDH activity.This technique prevents both, the loss of enzymes and the loss of reduction equivalents. There are given presuppositions for qualitative and quantitative histochemical investigations as well. The advantages of the new gel technique are discussed.     

A rapid assay for assessment of sphingosine kinase inhibitors and substrates

The effect of incorporating carbon nanotubes (CNTs) in the gel matrix on the electrophoretic mobility of proteins based on their molecular weight differences was investigated using sodium dodecyl sulfate–polyacrylamide gel electrophoresis (SDS–PAGE). More specifically, a reduction in standard deviation in the molecular weight calibration plots by 55% in the case of multiwalled carbon nanotubes (MWCNTs) and by 34% in the case of single-walled carbon nanotubes (SWCNTs) compared with that of pristine polyacrylamide gels was achieved after incorporating an insignificant amount of functionalized CNTs into the gel matrix. A mechanism based on a more uniform pore size distribution in CNT modified polyacrylamide gel matrix is proposed. Furthermore, the impact of SWCNTs and MWCNTs on the mobility of proteins in different molecular weight regimes at a given acrylamide concentration offers a tunable gel matrix in terms of the selection of molecular weight ranges of proteins. The robustness and excellent reproducibility of the CNT–PAGE protocol are expected to have a significant impact on the molecular weight determination of newly isolated proteins.     

Separation of long RNA by agarose–formaldehyde gel electrophoresis

We describe a method to facilitate electrophoretic separation of high-molecular-weight RNA species, such as ribosomal RNAs and their precursors, on agarose–formaldehyde gels. Two alternative “pK-matched” buffer systems were substituted for the traditionally used Mops-based conductive medium. The key advantages include shortened run times, a 5-fold reduction in formaldehyde concentration, a significantly improved resolution of long RNAs, and consistency in separation. The new procedure has a streamlined work flow that helps to minimize errors and is broadly applicable to agarose gel electrophoresis of RNA samples and their subsequent analysis by Northern blotting.     

Advanced negative detection method comparable to silver stain for SDS-PAGE separated proteins detection

In order to achieve an easy, rapid and sensitive protocol to detect proteins in polyacrylamide gel, an advanced negative detection method comparable to silver stain is described. When a gel was incubated with Phloxine B and followed by the development in acidic solution, the zones where forming protein-dye complex were selectively transparent, unlike opaque gel background. Within 50 min after electrophoresis, down to 0.1–0.4 ng of gel-separated proteins (similar with silver stain) could be observed, without labor-intensive and time-consuming procedure. Comparing with the most common negative stain method, Imidazole-zinc stain, Phloxine B stain has been shown higher sensitivity and distinct contrast between the transparent protein bands/spots and opaque background than those; furthermore, it is no longer necessary to concern about retention time of observation. This technique may provide a sensitive and practical choice for proteomics researches.     

Gel Electrophoresis of Chloroplast Polypeptides: Comparison of One-Dimensional and Two-Dimensional Gel Analyses of Chloroplast Polypeptides From Euglena gracilis

Euglena chloroplast polypeptides are resolved by an adaptation of the two-dimensional gel electrophoretic technique of O'Farrell (1975 J Biol Chem 250: 4007-4021). The present results are compared with those obtained by our earlier two-dimensional gel analyses as well as those obtained by one-dimensional gel analyses. Up to 75 micrograms of Euglena chloroplast polypeptides are resolved on one-dimensional sodium dodecylsulfate linear gradient 7.5 to 15% polyacrylamide gels into 43 stained polypeptide bands compared to only 33 bands resolved on a similar gel containing only 10% polyacrylamide. In contrast, two-dimensional gel electrophoresis (isoelectric focusing for the first dimension, sodium dodecylsulfate gel electrophoresis for the second dimension) further improves the resolution of the chloroplast polypeptides and especially so when a linear gradient gel is used for the second dimension. Delipidation of Euglena chloroplasts with acetone-ether and subsequent solubilization of polypeptides with Triton X-100 followed by sonication are all necessary for successful resolution of chloroplast polypeptides on two-dimensional gels. Up to 300 micrograms of chloroplast polypeptides can be clearly resolved into 56 to 59 stainable spots by the present two-dimensional gel technique when a linear gradient gel is used for the second dimension. Thus, about 30% of the polypeptide bands on a one-dimensional gel are separated into multiple polypeptides on a two-dimensional gel. The use of two-dimensional gels to separate labeled polypeptides with subsequent detection of labeled spots by autoradiography or fluorography again improves the resolution of the chloroplast polypeptides. For example, when ³⁵S-labeled chloroplast polypeptides are separated by the present two-dimensional gel technique with a linear gradient polyacrylamide gel in the second dimension, autoradiography or fluorography detects over 80 individual polypeptide spots. This is about twice the number resolved by our previous analyses which used a 10% polyacrylamide gel in the second dimension. Polypeptides detected range in molecular weight from about 8.5 to about 145 kilodaltons with apparent isoelectric points from pH 4.5 to 8.0. Fluorography provides rapid detection of labeled polypeptides and is 10 times more sensitive than autoradiography.     

Quantification of camalexin, a phytoalexin from Arabidopsis thaliana: a comparison of five analytical methods

Camalexin is a phytoalexin of Arabidopsis thaliana and an important component of inducible defenses. Accurate quantification of low concentrations suffers from interference by structurally related metabolites. A. thaliana plants were induced with silver nitrate and camalexin was extracted using methanol and identified and quantified by (i) TLC as a blue fluorescent band, (ii) microtiter plate-based fluorescence spectroscopy, (iii) GC on a midpolar column coupled to flame ionization detection, (iv) C₁₈ HPLC coupled to a photodiode detector, and (v) UPLC coupled to a mass spectrometer detector. Standard curves over the range of 0.1–15 μg ml⁻¹ gave R² values from 0.996 to 0.999. The different methods were compared and evaluated for their ability to detect and quantify increasing concentrations (<0.4–8 μg g⁻¹ FW) of camalexin. Each of the techniques presented advantages and disadvantages with regard to accuracy, precision, interference, analytical sensitivity, and limits of detection. TLC is a good qualitative technique for the identification of camalexin and fluorescence spectroscopy is subject to quenching when performed on crude extracts. Comparable results were obtained with GC–FID, HPLC–PDA, and UPLC–MS, with UPLC–MS having the added advantage of short analysis times and detection based on accurate mass.     

A dinoflagellate producer of pinnatoxin G, isolated from sub-tropical Japanese waters

A thecate dinoflagellate (Peridiniales, Dinophyceae) was cultured from individual non-calcareous cysts, isolated from surface sediment samples collected in Okinawa, Japan. Two isolates (CAWD188 and CAWD190) from two different sampling sites, each cultured from an individual cyst, produced ca. 11.9 and 15 pg cell⁻¹ pinnatoxin G, respectively, as determined by liquid chromatography–mass spectrometric (LC–MS). No other pinnatoxins were detected. The motile cells and cysts appeared morphologically identical to those of pinnatoxins E and F producers isolated from New Zealand waters and pinnatoxins E, F, and G producers isolated from Australian waters. Motile and cysts cells measured an average of 25 μm long × 21.3 μm wide and 29 μm long × 25.5 μm wide, respectively. Analysis of the large subunit ribosomal DNA sequence data showed two well supported strains with slight differences between the Japanese and the Australasian isolates.