Biological treatment of ammonium-rich wastewater by partial nitritation and subsequent anaerobic ammonium oxidation (anammox) in a pilot plant

In wastewater treatment plants with anaerobic sludge digestion, 15-20% of the nitrogen load is recirculated to the main stream with the return liquors from dewatering. Separate treatment of this ammonium-rich digester supernatant would significantly reduce the nitrogen load of the activated sludge system. Some years ago, a novel biological process was discovered in which ammonium is converted to nitrogen gas under anoxic conditions with nitrite as the electron acceptor (anaerobic ammonium oxidation, anammox). Compared to conventional nitrification and denitrification, the aeration and carbon-source demand is reduced by over 50 and 100%, respectively. The combination of partial nitritation to produce nitrite in a first step and subsequent anaerobic ammonium oxidation in a second reactor was successfully tested on a pilot scale (3.6 m(3)) for over half a year. This report focuses on the feasibility of nitrogen removal from digester effluents from two different wastewater treatment plants (WWTPs) with the combined partial nitritation/anammox process. Nitritation was performed in a continuously stirred tank reactor (V=2.0 m(3)) without sludge retention. Some 58% of the ammonium in the supernatant was converted to nitrite. At 30 degrees C the maximum dilution rate D(x) was 0.85 d(-1), resulting in nitrite production of 0.35 kg NO(2)-N m(-3)(reactor) d(-1). The nitrate production was marginal. The anaerobic ammonium oxidation was carried out in a sequencing batch reactor (SBR, V=1.6 m(3)) with a nitrogen elimination rate of 2.4 kg N m(-3)(reactor) d(-1) during the nitrite-containing periods of the SBR cycle. Over 90% of the inlet nitrogen load to the anammox reactor was removed and the sludge production was negligible. The nitritation efficiency of the first reactor limited the overall maximum rate of nitrogen elimination.     

Anaerobic ammonium oxidation in marine environments: contribution to biogeochemical cycles and biotechnological developments for wastewater treatment

Microbial processes are responsible for most reactions involved in the nitrogen cycle in the oceans, which determine the fluxes of this crucial nutrient in these environments. The present review provides an overview of the contribution of anaerobic ammonium oxidation (Anammox) to marine biogeochemical processes. Besides the conventional Anammox process, anaerobic ammonium oxidation coupled to the microbial reduction of alternative electron acceptors, such as sulfate (Sulfammox), ferric iron (Feammox), and natural organic matter (NOM-dependent Anammox) is also described in the context of global marine biogeochemical cycles. Also, the complex interactions among the oceanic biogeochemical cycles of N, S and Fe are discussed at the light of the new findings available in the literature. The review also underlines the important role of the microbial processes performing the Anammox reaction in the development of wastewater treatment systems for the removal of nitrogen from saline effluents. Strategies to enrich and immobilize Anammox bacteria in different reactor configurations for the treatment of saline wastewaters are also described as well as future directions for novel biotechnological developments based on Anammox.

     

New Aspects of Microbial Nitrogen Transformations in the Context of Wastewater Treatment – A Review

Over the past few years, new technologies for nitrogen removal have been developed mainly because of the increasing financial costs of the traditional wastewater treatment technologies. Newly discovered pathways, like the anaerobic oxidation of ammonium (ANAMMOX), and uses for nitrogen removal technologies are under discussion. Processes and technologies such as: Partial nitrification; Single reactor systems for High Ammonium Removal Over Nitrite (SHARON); Anammox; Aerobic/anoxic deammonification; Oxygen Limited Autotrophic Nitrification‐Denitrification (OLAND); Completely Autotrophic Nitrogen Removal Over Nitrite (CANON); wetland based systems, all have a high potential for nitrogen removal. However, the pathways of nitrogen transformation processes are very complex. An understanding of how various environmental factors affect these processes and a sound knowledge of existing, worldwide experience pertaining to these novel technologies are the key if the nitrogen removal rates are to be improved and success is to be realized in full‐scale applications. This review describes the present knowledge of the new treatment technologies for wastewater with high nitrogen loads. Special emphasis is given to the influence of environmental factors and the reactor configuration on the nitrogen transformation process and microbial activity.     

废水自养生物脱氮技术研究进展

基于短程硝化和厌氧氨氧化的自养脱氮工艺是生物脱氮领域研究的热点,它的发现为低碳氮比废水的处理提供了新的思路。近些年来,人们陆续开发了SHARON、ANAMMOX、CANON、OLAND等自养生物脱氮工艺,进一步推动了高效、低耗脱氮技术的开发和研究。本文从工艺原理、特点等方面,对自养生物脱氮工艺的国内外研究状况进行了总结和对比,并提出了存在的问题及发展方向。     

Biological nutrients removal from the supernatant originating from the anaerobic digestion of the organic fraction of municipal solid waste

Abstract

This study critically evaluates the biological processes and techniques applied to remove nitrogen and phosphorus from the anaerobic supernatant produced from the treatment of the organic fraction of municipal solid waste (OFMSW) and from its co-digestion with other biodegradable organic waste (BOW) streams. The wide application of anaerobic digestion for the treatment of several organic waste streams results in the production of high quantities of anaerobic effluents. Such effluents are characterized by high nutrient content, because organic and particulate nitrogen and phosphorus are hydrolyzed in the anaerobic digestion process. Consequently, adequate post-treatment is required in order to comply with the existing land application and discharge legislation in the European Union countries. This may include physicochemical and biological processes, with the latter being more advantageous due to their lower cost. Nitrogen removal is accomplished through the conventional nitrification/denitrification, nitritation/denitritation and the complete autotrophic nitrogen removal process; the latter is accomplished by nitritation coupled with the anoxic ammonium oxidation process. As anaerobic digestion effluents are characterized by low COD/TKN ratio, conventional denitrification/nitrification is not an attractive option; short-cut nitrogen removal processes are more promising. Both suspended and attached growth processes have been employed to treat the anaerobic supernatant. Specifically, the sequencing batch reactor, the membrane bioreactor, the conventional activated sludge and the moving bed biofilm reactor processes have been investigated. Physicochemical phosphorus removal via struvite precipitation has been extensively examined. Enhanced biological phosphorus removal from the anaerobic supernatant can take place through the sequencing anaerobic/aerobic process. More recently, denitrifying phosphorus removal via nitrite or nitrate has been explored. The removal of phosphorus from the anaerobic supernatant of OFMSW is an interesting research topic that has not yet been explored. At the moment, standardization in the design of facilities that treat anaerobic supernatant produced from the treatment of OFMSW is still under development. To move toward this direction, it is first necessary to assess the performance of alternative treatment options. It study concentrates existing data regarding the characteristics of the anaerobic supernatant produced from the treatment of OFMSW and from their co-digestion with other BOW. This provides data documenting the effect of the anaerobic digestion operating conditions on the supernatant quality and critically evaluates alternative options for the post-treatment of the liquid fraction produced from the anaerobic digestion process.     

Sensitivity analysis of a biofilm model describing a one-stage completely autotrophic nitrogen removal (CANON) process.

A mathematical model for nitrification and anaerobic ammonium oxidation (ANAMMOX) processes in a single biofilm reactor (CANON) was developed. This model describes completely autotrophic conversion of ammonium to dinitrogen gas. Aerobic ammonium and nitrite oxidation were modeled together with ANAMMOX. The sensitivity of kinetic constants and biofilm and process parameters to the process performance was evaluated, and the total effluent concentrations were, in general, found to be insensitive to affinity constants. Increasing the amount of biomass by either increasing biofilm thickness and density or decreasing porosity had no significant influence on the total effluent concentrations, provided that a minimum total biomass was present in the reactor. The ANAMMOX process always occurred in the depth of the biofilm provided that the oxygen concentration was limiting. The optimal dissolved oxygen concentration level at which the maximum nitrogen removal occurred is related to a certain ammonium surface load on the biofilm. An ammonium surface load of 2 g N/m2. d, associated with a dissolved oxygen concentration level of 1.3 g O2/m3 in the bulk liquid and with a minimum biofilm depth of 1 mm seems a proper design condition for the one-stage ammonium removal process. Under this condition, the ammonium removal efficiency is 94% (82% for the total nitrogen removal efficiency) (30 degrees C). Better ammonium removal could be achieved with an increase in the dissolved oxygen concentration level, but this would strongly limit the ANAMMOX process and decrease total nitrogen removal. It can be concluded that a one-stage process is probably not optimal if a good nitrogen effluent is required. A two-stage process like the combined SHARON and ANAMMOX process would be advised for complete nitrogen removal.     

Batch culture enrichment of ANAMMOX populations from anaerobic and aerobic seed cultures

Discharge of nitrate and ammonia rich wastewaters into the natural waters encourage eutrophication, and contribute to aquatic toxicity. Anaerobic ammonium oxidation process (ANAMMOX) is a novel biological nitrogen removal alternative to nitrification-denitrification, that removes ammonia using nitrite as the electron acceptor. The feasibility of enriching the ANAMMOX bacteria from the anaerobic digester sludge of a biomethanation plant treating vegetable waste and aerobic sludge from an activated sludge process treating domestic sewage is reported in this paper. ANAMMOX bacterial activity was monitored and established in terms of nitrogen transformations to ammonia, nitrite and nitrate along with formation of hydrazine and hydroxylamine.     

Nitrogen removal from animal waste treatment water by anammox enrichment

The aim of this work was to examine the applicability of the anaerobic ammonium oxidation (anammox) process to three kinds of low BOD/N ratio wastewaters from animal waste treatment processes in batch mode. A rapid decrease of NO(2)(-) and NH(4)(+) was observed during incubation with wastewaters from AS and UASB/trickling filter and their corresponding control artificial wastewaters. This nitrogen removal resulted from the anammox reaction, because the ratio of removed NO(2)(-) and NH(4)(+) was close to the theoretical ratio of the anammox reaction. Comparison of the inorganic nitrogen removal rate of the actual wastewater and that of control artificial wastewater showed that these two kinds of wastewater were very suitable for anammox treatment. Incubation with wastewater from RW did not show a clear anammox reaction; however, diluting it by half enabled the reaction, suggesting the presence of an inhibitory factor. This study showed that the three kinds of wastewater from animal waste treatment processes were suitable for anammox treatment.     

利用硝酸盐和亚硝酸盐同步富集厌氧甲烷氧化微生物的比较实验

【背景】反硝化厌氧甲烷氧化(Denitrifying anaerobic methane oxidation,DAMO)是以硝酸盐或亚硝酸盐为电子受体以甲烷为电子供体的厌氧氧化过程,对认识全球碳氮循环、削减温室气体排放和开发废水脱氮新技术等方面具有重要意义。【目的】认识以硝酸盐和亚硝酸盐为电子受体的DAMO微生物富集过程和结果的差异性。【方法】在序批式反应器(Sequencing batch reaetor,SBR)内接种混合物,分别以硝酸盐和亚硝酸盐为电子受体连续培养800 d,定期检测反应器基质浓度变化、计算转化速率;利用16S rRNA基因系统发育分析研究功能微生物的多样性,利用实时荧光定量PCR技术定量测定功能微生物。【结果】以亚硝酸盐为电子受体的1、3号反应器富集到了DAMO细菌,未检测到DAMO古菌;以硝酸盐为电子受体的2号反应器富集到了DAMO细菌和古菌的混合物;3个反应器的脱氮速率经过初始低速期、快速提升期,最终达到稳定,但2号快速提升期开始时间比1、3号晚了80 d左右,达到稳定的时间更长,稳定最大速率为1、3号的44.7%、40.3%。【结论】硝酸盐和亚硝酸盐对富集产物有决定性影响;以硝酸盐为电子受体富集得到的DAMO古菌和细菌协同体系可以长期稳定共存,DAMO古菌可能是协同体系中脱氮速率的限制性因素。     

Evaluation of Anammox and denitrification during anaerobic digestion of poultry manure

Two approaches based on ne w process development and biological nitrogen transformation were investigated in a bench study for removing nitrogen as N2 gas from poultry waste while stabilizing the wastes. The process, known as "Anammox", was explored in batch anaerobic culture using serum bottles. The Anammox process involves the use of nitrite as an electron acceptor in the bacterially mediated oxidation of ammonia to yield N2. Studies are described wherein nitrite was added to poultry waste and the effects on ammonium levels were monitored. About 13-22% ammonium removal was observed with the inoculation of returned activated sludge, and the total ammonium reduction was not proportional to the reduction of nitrite, thereby suggesting that Anammox was less competitive under the conditions in our studies. The addition of nitrite and nitrate was not inhibitory to the process based on gas generation and COD reduction. The classical nitrogen removal process of nitrification followed with denitrification offers a more reliable basis for nitrogen removal from poultry wastes.     

厌氧氨氧化工艺的应用现状和问题

厌氧氨氧化(Anaerobic ammonium oxidation,ANAMMOX)工艺因其高效低耗的优势,在废水生物脱氮领域具有广阔的应用前景。在过去的20年中,许多基于ANAMMOX反应的工艺得以不断研究和应用。预计到2014年末,全球范围内的ANAMMOX工程将会超过100座。综述了各种形式的ANAMMOX工艺,包括短程硝化-厌氧氨氧化、全程自养脱氮、限氧自养硝化反硝化、反硝化氨氧化、好氧反氨化、同步短程硝化-厌氧氨氧化-反硝化耦合、单级厌氧氨氧化短程硝化脱氮工艺。对一体式和分体式工艺运行条件进行了比较,结合ANAMMOX工艺工程(主要包括移动床生物膜,颗粒污泥和序批式反应器系统)应用现状,总结了工程化应用过程中遇到的问题及其解决对策,在此基础上对今后的研究和应用方向进行了展望。今后的研究重点应集中于运行条件的优化和水质障碍因子的解决,尤其是工艺自动化控制系统的开发和特殊废水对工艺性能影响的研究。     

New concepts of microbial treatment processes for the nitrogen removal in wastewater

Many countries strive to reduce the emissions of nitrogen compounds (ammonia, nitrate, NOx) to the surface waters and the atmosphere. Since mainstream domestic wastewater treatment systems are usually already overloaded with ammonia, a dedicated nitrogen removal from concentrated secondary or industrial wastewaters is often more cost-effective than the disposal of such wastes to domestic wastewater treatment. The cost-effectiveness of separate treatment has increased dramatically in the past few years, since several processes for the biological removal of ammonia from concentrated waste streams have become available. Here, we review those processes that make use of new concepts in microbiology: partial nitrification, nitrifier denitrification and anaerobic ammonia oxidation (the anammox process). These processes target the removal of ammonia from gases, and ammonium-bicarbonate from concentrated wastewaters (i.e. sludge liquor and landfill leachate). The review addresses the microbiology, its consequences for their application, the current status regarding application, and the future developments.     

Versatility and application of anaerobic ammonium-oxidizing bacteria

With the unique cell compartmentalization and the ability to simultaneously oxidize ammonium and reduce nitrite into nitrogen gas, anaerobic ammonium-oxidizing (anammox) bacteria have challenged our recognitions of microorganism. The research conducted on these bacteria has been extended from bench-scale tryouts to full-scale reactor systems. This review addresses the recently discovered versatile properties of anammox bacteria and the applications and obstacles of implementing the anammox process in ammonia-rich wastewater treatment. We also discuss the merits and drawbacks of traditional and anammox-based processes for nitrogen removal and suggest areas for improvement.     

Treatment of landfill leachate using UASB-MBR-SHARON–Anammox configuration

Leachate treatment is a challenging issue due to its high pollutant loads. There are several studies on feasible treatment methods of leachate. In the scope of this study, high organic content of young leachate was eliminated using an upflow anaerobic sludge blanket (UASB) and a membrane bioreactor (MBR) in sequence and effluent of the system was given to single reactor for high activity ammonia removal over nitrite (SHARON) and anaerobic ammonia oxidation (Anammox) reactors to remove nitrogen content. All reactors were set up at lab scale in order to evaluate the usage of these processes in sequencing order for leachate treatment. COD and TKN removal efficiencies were over 90 % in the combined processes which were operated during the study. The biodegradable portion of organic matter was removed with an efficiency of 99 %. BOD₅ concentration decreased to 50 mg/L by UASB and MBR in sequence even the influent BOD₅ concentration was over 8,000 mg/L. Although high nitrogen concentrations were observed in raw leachate, successful removal of nitrogen was accomplished by consecutive operations of SHARON and Anammox reactors. The results of this study demonstrated that with an efficient pretreatment of leachate, the combination of SHARON–Anammox processes is an effective method for the treatment of high nitrogen content in leachate.     

Combined anaerobic ammonium and methane oxidation for nitrogen and methane removal

Anammox (anaerobic ammonium oxidation) is an environment-friendly and cost-efficient nitrogen-removal process currently applied to high-ammonium-loaded wastewaters such as anaerobic digester effluents. In these wastewaters, dissolved methane is also present and should be removed to prevent greenhouse gas emissions into the environment. Potentially, another recently discovered microbial pathway, n-damo (nitrite-dependent anaerobic methane oxidation) could be used for this purpose. In the present paper, we explore the feasibility of simultaneously removing methane and ammonium anaerobically, starting with granules from a full-scale anammox bioreactor. We describe the development of a co-culture of anammox and n-damo bacteria using a medium containing methane, ammonium and nitrite. The results are discussed in the context of other recent studies on the application of anaerobic methane- and ammonia-oxidizing bacteria for wastewater treatment.     

厌氧氨氧化膨胀床反应器的运行性能

试验研究了以竹炭为载体的厌氧氨氧化膨胀床反应器的运行性能.接种反硝化污泥,用模拟废水可成功启动该反应器:运行至144 d时,容积总氮去除率达到3.02 kg N/m3/d.这是国内文献报道的最高水平.动力学分析表明.这种反应器的最大容积总氮去除率可迭12.77 kg N/m3/d.具有很大的脱氮潜能.反应器的启动过程可分为菌体自溶、活性延滞和活性提高三个阶段.与此相应,污泥性状也从黄褐色絮状污泥变为棕灰色颗粒污泥和红色颗粒污泥.红色颗粒污泥以杆茵和球菌为主.厌氧氨氧化活性可达0.56mg TN/(mgprotein)/h,它们是反应器厌氧氨氧化功能的主要承载者.     

湖泊氮素氧化及脱氮过程研究进展

自然界中氮的生物地球化学循环主要由微生物驱动,由固氮作用、硝化作用、反硝化作用和氨化作用来完成。过去数十年间,随着异养硝化、厌氧氨氧化和古菌氨氧化作用的发现,人们对环境中氮素循环认识逐步深入,提出了多种脱氮途径新假说。对湖泊生态系统中氮素的输入、输出及其在水体、沉积物和水土界面的迁移转化过程进行了概括,对湖泊生态系统中反硝化和厌氧氨氧化脱氮机理及脱氮效率的最新研究进展进行了探讨,并对以后的氮素循环研究进行了展望。     

Nitrogen source effects on the denitrifying anaerobic methane oxidation culture and anaerobic ammonium oxidation bacteria enrichment process

The co-culture system of denitrifying anaerobic methane oxidation (DAMO) and anaerobic ammonium oxidation (Anammox) has a potential application in wastewater treatment plant. This study explored the effects of permutation and combination of nitrate, nitrite, and ammonium on the culture enrichment from freshwater sediments. The co-existence of NO₃ ⁻, NO₂ ⁻, and NH₄ ⁺ shortened the enrichment time from 75 to 30 days and achieved a total nitrogen removal rate of 106.5 mg/L/day on day 132. Even though ammonium addition led to Anammox bacteria increase and a higher nitrogen removal rate, DAMO bacteria still dominated in different reactors with the highest proportion of 64.7% and the maximum abundance was 3.07 ± 0.25 × 10⁸ copies/L (increased by five orders of magnitude) in the nitrite reactor. DAMO bacteria showed greater diversity in the nitrate reactor, and one was similar to M. oxyfera; DAMO bacteria in the nitrite reactor were relatively unified and similar to M. sinica. Interestingly, no DAMO archaea were found in the nitrate reactor. This study will improve the understanding of the impact of nitrogen source on DAMO and Anammox co-culture enrichment.

     

Enhancing mainstream nitrogen removal by employing nitrate/nitrite-dependent anaerobic methane oxidation processes

Due to serious eutrophication in water bodies, nitrogen removal has become a critical stage for wastewater treatment plants (WWTPs) over past decades. Conventional biological nitrogen removal processes are based on nitrification and denitrification (N/DN), and are suffering from several major drawbacks, including substantial aeration consumption, high fugitive greenhouse gas emissions, a requirement for external carbon sources, excessive sludge production and low energy recovery efficiency, and thus unable to satisfy the escalating public needs. Recently, the discovery of anaerobic ammonium oxidation (anammox) bacteria has promoted an update of conventional N/DN-based processes to autotrophic nitrogen removal. However, the application of anammox to treat domestic wastewater has been hindered mainly by unsatisfactory effluent quality with nitrogen removal efficiency below 80%. The discovery of nitrate/nitrite-dependent anaerobic methane oxidation (n-DAMO) during the last decade has provided new opportunities to remove this barrier and to achieve a robust system with high-level nitrogen removal from municipal wastewater, by utilizing methane as an alternative carbon source. In the present review, opportunities and challenges for nitrate/nitrite-dependent anaerobic methane oxidation are discussed. Particularly, the prospective technologies driven by the cooperation of anammox and n-DAMO microorganisms are put forward based on previous experimental and modeling studies. Finally, a novel WWTP system acting as an energy exporter is delineated.