Antibody detection of SARS-CoV spike and nucleocapsid protein

Early detection and identification of SARS-CoV-infected patients and actions to prevent transmission are absolutely critical to prevent another SARS outbreak. Antibodies that specifically recognize the SARS-CoV spike and nucleocapsid proteins may provide a rapid screening method to allow accurate identification and isolation of patients with the virus early in their infection. For this reason, we raised peptide-induced polyclonal antibodies against SARS-CoV spike protein and polyclonal antibodies against SARS-CoV nucleocapsid protein using 6x His nucleocapsid recombinant protein. Western blot analysis and immunofluorescent staining showed that these antibodies specifically recognized SARS-CoV.     

Direct protein detection with a nano-interdigitated array gate MOSFET

A new protein sensor is demonstrated by replacing the gate of a metal oxide semiconductor field effect transistor (MOSFET) with a nano-interdigitated array (nIDA). The sensor is able to detect the binding reaction of a typical antibody Ixodes ricinus immunosuppressor (anti-Iris) protein at a concentration lower than 1 ng/ml. The sensor exhibits a high selectivity and reproducible specific detection. We provide a simple model that describes the behavior of the sensor and explains the origin of its high sensitivity. The simulated and experimental results indicate that the drain current of nIDA-gate MOSFET sensor is significantly increased with the successive binding of the thiol layer, Iris and anti-Iris protein layers. It is found that the sensor detection limit can be improved by well optimizing the geometrical parameters of nIDA-gate MOSFET. This nanobiosensor, with real-time and label-free capabilities, can easily be used for the detection of other proteins, DNA, virus and cancer markers. Moreover, an on-chip associated electronics nearby the sensor can be integrated since its fabrication is compatible with complementary metal oxide semiconductor (CMOS) technology.     

A novel peptide microarray for protein detection and analysis utilizing a dry peptide array system

A novel dry peptide microarray system has been constructed that affords a practical solution for protein detection and analysis. This system is an array preparation and assay procedure under dry conditions that uses designed peptides as non-immobilized capture agents for the detection of proteins. The system has several advantages that include its portability and ease-of-use, as well as the fact that vaporization of sample solutions need not be considered. In this study, various proteins have been characterized with an alpha-helical peptide mini-library. When proteins were added to the peptide library array, the fluorescent peptides showed different fluorescent intensities depending on their sequences. The patterns of these responses could be regarded as 'protein fingerprints' (PFPs), which are sufficient to establish the identities of the target proteins. Furthermore, statistical analysis of the resulting PFPs was performed using cluster analysis. The PFPs of the proteins were clustered successfully depending on their families and binding properties. Additionally, the target protein was characterized using a nanolitre system and could be detected down to 1.2 fmol. These studies imply that the dry peptide array system is a promising tool for detecting and analyzing target proteins. The dry peptide array will play a role in development of high-throughput protein-detecting nano/micro arrays for proteomics and ligand screening studies.     

Resolving protein interactions and complexes by affinity purification followed by label-based quantitative mass spectrometry

Label-based quantitative mass spectrometry analysis of affinity purified complexes, with its built-in negative controls and relative ease of use, is an increasingly popular choice for defining protein-protein interactions and multiprotein complexes. This approach, which differentially labels proteins/peptides from two or more populations and combines them prior to analysis, permits direct comparison of a protein pulldown (e.g. affinity purified tagged protein) to that of a control pulldown (e.g. affinity purified tag alone) in a single mass spectrometry (MS) run, thus avoiding the variability inherent in separate runs. The use of quantitative techniques has been driven in large part by significant improvements in the resolution and sensitivity of high-end mass spectrometers. Importantly, the availability of commercial reagents and open source identification/quantification software has made these powerful techniques accessible to nonspecialists. Benefits and drawbacks of the most popular labeling-based approaches are discussed here, and key steps/strategies for the use of labeling in quantitative immunoprecipitation experiments detailed.     

Antibody for detection and quantitation of membrane-associated folate-binding protein from Lactobacillus casei

Lactobacillus casei cells contain a 25 kDa, membrane-associated, folate-binding protein (fbp), which is a component of the folate transport system. Polyclonal antibody to fbp (anti-fbp) has been prepared, and conditions have been established for detection and quantitation of the protein. Anti-fbp did not block [3H]folate transport or binding in L. casei cells. As judged by Western blots, the antibody reacted only with fbp on sodium dodecyl sulfate electrophoretograms of Triton X-100 extracts of L. casei membranes. Anti-fbp showed no cross-reactivity with L. casei dihydrofolate reductase, L. casei 5,10-methenyltetrahydrofolate synthetase, L1210 dihydrofolate reductase, rat liver dihydrofolate reductase, or L1210 folate-binding protein. Enzyme-linked immunosorbent assay measurements indicated the presence of an fbp in membranes of Lactobacillus salivarius and two transport-defective sublines of L. casei. Anti-fbp was used to demonstrate selective extraction, with n-butanol, of fbp from a mixture of Triton-solubilized L. casei membrane proteins; repression of fbp in membranes of L. casei cells grown on high levels of folate; and localization of fbp by electron microscopy, using anti-fbp in conjunction with goat anti-rabbit IgG gold conjugate, in L. casei membranes.     

Comparison of label-free and label-based strategies for proteome analysis of hepatoma cell lines

Within the past decade numerous methods for quantitative proteome analysis have been developed of which all exhibit particular advantages and disadvantages. Here, we present the results of a study aiming for a comprehensive comparison of ion-intensity based label-free proteomics and two label-based approaches using isobaric tags incorporated at the peptide and protein levels, respectively. As model system for our quantitative analysis we used the three hepatoma cell lines HepG2, Hep3B and SK-Hep-1. Four biological replicates of each cell line were quantitatively analyzed using an RPLC–MS/MS setup. Each quantification experiment was performed twice to determine technical variances of the different quantification techniques. We were able to show that the label-free approach by far outperforms both TMT methods regarding proteome coverage, as up to threefold more proteins were reproducibly identified in replicate measurements. Furthermore, we could demonstrate that all three methods show comparable reproducibility concerning protein quantification, but slightly differ in terms of accuracy. Here, label-free was found to be less accurate than both TMT approaches. It was also observed that the introduction of TMT labels at the protein level reduces the effect of underestimation of protein ratios, which is commonly monitored in case of TMT peptide labeling. Previously reported differences in protein expression between the particular cell lines were furthermore reproduced, which confirms the applicability of each investigated quantification method to study proteomic differences in such biological systems. This article is part of a Special Issue entitled: Biomarkers: A Proteomic Challenge.     

Electrical protein array chips for the detection of staphylococcal virulence factors

A new approach for the detection of virulence factors of Staphylococcus aureus and Staphylococcus epidermidis using an electrical protein array chip technology is presented. The procedure is based on an enzyme-linked sandwich immunoassay, which includes recognition and binding of virulence factors by specific capture and detection antibodies. Detection of antibody-bound virulence factors is achieved by measuring the electrical current generated by redox recycling of an enzymatically released substance. The current (measured in nanoampere) corresponds to the amount of the target molecule in the analyzed sample. The electrical protein chip allows for a fast detection of Staphylococcus enterotoxin B (SEB) of S. aureus and immunodominant antigen A homologue (IsaA homologue) of S. epidermidis in different liquid matrices. The S. aureus SEB virulence factor could be detected in minimal medium, milk, and urine in a concentration of 1 ng/ml within less than 23 min. Furthermore, a simultaneous detection of SEB of S. aureus and IsaA homologue of S. epidermidis in a single assay could be demonstrated.     

Multiplex detection of B-type natriuretic Peptide, cardiac troponin I and C-reactive protein with photonic suspension array

A novel photonic suspension array has been developed for multiplex immunoassay. The carriers of this array were silica colloidal crystal beads (SCCBs). The codes of these carriers have characteristic reflection peaks originating from their structural periodicity; therefore they do not suffer from fading, bleaching, quenching or chemical instability. In addition, the fluorescence background of SCCBs is negligible because no fluorescence materials or dyes are involved. With a sandwich method, the proposed suspension array was used for simultaneous multiplex detection of heart failure (HF) and coronary heart disease (CAD) biomarkers in one test tube. The results showed that the three biomarkers: cardiac troponin I (cTnI), C-reactive protein (CRP) and B-type natriuretic peptide (BNP) could be assayed in the ranges of 0.1-500 ng/ml, 1-500 mg/L and 0.02-50 ng/ml with detection limits of 0.01 ng/ml, 0.36 mg/L and 0.004 ng/ml at 3σ, respectively. There were no significant differences between the photonic suspension array and traditional parallel single-analyte test. This novel method demonstrated acceptable accuracy, high detection sensitivity and reproducibility and excellent storage stability. This technique provides a new strategy for low cost, automated, and simultaneous multiplex immunoassays of bio-markers.     

A sol-gel-integrated protein array system for affinity analysis of aptamer-target protein interaction

A sol-gel microarray system was developed for a protein interaction assay with high activity. Comparing to 2-dimensional microarray surfaces, sol-gel can offer a more dynamic and broad range for proteins. In the present study, this sol-gel-integrated protein array was used in binding affinity analysis for aptamers. Six RNA aptamers and their target protein, yeast TBP (TATA-binding protein), were used to evaluate this method. A TBP-containing sol-gel mixture was spotted using a dispensing workstation under high-humidity conditions and each Cy-3-labeled aptamer was incubated. The dissociation constants (K(d)) were calculated by plotting the fluorescent intensity of the bound aptamers as a function of the TBP concentrations. The K(d) value of the control aptamer was found to be 8?nM, which agrees well with the values obtained using the conventional method, electric mobility shift assay. The sol-gel-based binding affinity measurements fit well with conventional binding affinity measurements, suggesting their possible use as an alternative to the conventional method. In addition, aptamer affinity measurements by the sol-gel-integrated protein chip make it possible to develop a simple high-throughput affinity method for screening high-affinity aptamers.     

High density DNA methylation array with single CpG site resolution

We have developed a new generation of genome-wide DNA methylation BeadChip which allows high-throughput methylation profiling of the human genome. The new high density BeadChip can assay over 480K CpG sites and analyze twelve samples in parallel. The innovative content includes coverage of 99% of RefSeq genes with multiple probes per gene, 96% of CpG islands from the UCSC database, CpG island shores and additional content selected from whole-genome bisulfite sequencing data and input from DNA methylation experts. The well-characterized Infinium® Assay is used for analysis of CpG methylation using bisulfite-converted genomic DNA. We applied this technology to analyze DNA methylation in normal and tumor DNA samples and compared results with whole-genome bisulfite sequencing (WGBS) data obtained for the same samples. Highly comparable DNA methylation profiles were generated by the array and sequencing methods (average R² of 0.95). The ability to determine genome-wide methylation patterns will rapidly advance methylation research.     

High resolution detection and analysis of CpG dinucleotides methylation using MBD-Seq technology

Methyl-CpG binding domain protein sequencing (MBD-seq) is widely used to survey DNA methylation patterns. However, the optimal experimental parameters for MBD-seq remain unclear and the data analysis remains challenging. In this study, we generated high depth MBD-seq data in MCF-7 cell and developed a bi-asymmetric-Laplace model (BALM) to perform data analysis. We found that optimal efficiency of MBD-seq experiments was achieved by sequencing ～100 million unique mapped tags from a combination of 500 mM and 1000 mM salt concentration elution in MCF-7 cells. Clonal bisulfite sequencing results showed that the methylation status of each CpG dinucleotides in the tested regions was accurately detected with high resolution using the proposed model. These results demonstrated the combination of MBD-seq and BALM could serve as a useful tool to investigate DNA methylome due to its low cost, high specificity, efficiency and resolution.     

Flow injection analysis with diode array absorbance detection and dynamic surface tension detection for studying denaturation and surface activity of globular proteins

In this article, a multidimensional dynamic surface tension detector (DSTD), in a parallel configuration with a UV-visible diode array absorbance detector, is presented in a novel flow injection analysis (FIA) application to study the effects of chemical denaturants urea, guanidinium hydrochloride (GdmHCl), and guanidinium thyocyanate (GdmSCN) on the surface activity of globular proteins at the liquid-air interface. The DSTD signal is obtained by measuring the changing pressure across the liquid-air interface of 4-mul drops repeatedly forming at the end of a capillary using FIA. The sensitivity and selectivity of the DSTD signal is related to the surface-active protein concentration in aqueous solution combined with the thermodynamics and kinetics of protein interaction at a liquid-air drop interface. Rapid on-line calibration and measurement of dynamic surface tension is applied, with the surface tension converted into surface pressure results. Continuous surface tension measurement throughout the entire drop growth is achieved, providing insight into kinetic behavior of protein interactive processes at the liquid-air drop interface. Specifically, chemical denaturation of 12 commercial globular proteins-chicken egg albumin, bovine serum albumin, human serum albumin, alpha-lactalbumin (alpha-Lac), myoglobin, cytochrome c, hemoglobin, carbonic anhydrase, alpha-chymotrypsinogen A, beta-lactoglobulin (beta-LG), lysozyme, and glyceraldehyde-3-phosphate-dehydrogenase-is studied in terms of surface pressure (i.e., surface activity) after treatment with increasing concentrations of urea, GdmHCl, and GdmSCN in the 0-8, 0-6, and 0-5 M ranges, respectively. For several of these proteins, the spectroscopic absorbance changes are monitored simultaneously to provide additional information prior to drop formation. Results show that surface pressure of proteins generally increases as the denaturant concentration increases and that effectiveness is GdmSCN > GdmHCl > urea. Protein unfolding curves obtained by plotting surface pressure as a function of denaturant concentration are presented and compared with respect to unfolding curves obtained by using UV absorbance and literature data. Kinetic information relative to the protein adsorption to the air-liquid interface of two proteins, alpha-Lac and beta-LG (chosen as representative proteins for comparison), denatured by the three denaturants is also studied and discussed.     

A simple and rapid protein array based method for the simultaneous detection of biowarfare agents

A protein chip has been developed that allows the simultaneous detection of a multitude of different biowarfare agents. The chip was developed for the ArrayTube platform providing a cheap and easy to handle technology solution that combines a microtube-integrated protein chip with the classical procedure of a sandwich-enzyme-linked immunosorbent assay and signal amplification by streptavidin-poly-horseradish peroxidase. Specific immunoassays for Staphylococcus enterotoxin B, ricin, Venezuelan equine encephalitis virus, St. Louis encephalitis virus, West Nile virus, Yellow fever virus, Orthopox virus species, Francisella tularensis, Yersinia pestis, Brucella melitensis, Burkholderia mallei and Escherichia coli EHEC O157:H7 were developed and optimized. All assays could be completed within 1 to 1 1/2 h and detection levels were demonstrated to be as low as in well established ELISAs. Most interesting, as a result of careful antibody screening and testing, it is currently possible to analyse at least five of the "dirty dozen" agents on one single protein chip in parallel.     

Exon array CGH: detection of copy-number changes at the resolution of individual exons in the human genome

The development of high-throughput screening methods such as array-based comparative genome hybridization (array CGH) allows screening of the human genome for copy-number changes. Current array CGH strategies have limits of resolution that make detection of small (less than a few tens of kilobases) gains or losses of genomic DNA difficult to identify. We report here a significant improvement in the resolution of array CGH, with the development of an array platform that utilizes single-stranded DNA array elements to accurately measure copy-number changes of individual exons in the human genome. Using this technology, we screened 31 patient samples across an array containing a total of 162 exons for five disease genes and detected copy-number changes, ranging from whole-gene deletions and duplications to single-exon deletions and duplications, in 100% of the cases. Our data demonstrate that it is possible to screen the human genome for copy-number changes with array CGH at a resolution that is 2 orders of magnitude higher than that previously reported.     

Analysis of protein interaction and function with a 3-dimensional MALDI-MS protein array

Protein profiling and characterization of protein interactions in biological samples ultimately require indicator-free methods of signal detection, which likewise offer an opportunity to distinguish specific interactions from nonspecific protein binding. Here we describe a new 3-dimensional protein microchip for detecting biomolecular interactions with matrix-assisted laser desorption-ionization mass spectrometry (MALDI-MS); the microchip comprises a high-density array of methacrylate polymer elements containing immobilized proteins as capture molecules and directly interfaces with a commercially available mass spectrometer. We demonstrated the performance of the chip in three types of experiments by detecting antibody-antigen interactions, enzymatic activity, and enzyme-inhibitor interactions. MALDI-MS biochip-based tumor necrosisfactor alpha (TNF-alpha) immunoassays demonstrated the feasibility of detecting antigens in complex biological samples by identifying molecular masses of bound proteins even at high nonspecific protein binding. By detecting model interactions of trypsin with trypsin inhibitors, we showed that the protein binding capacity of methacrylate polymer elements and the sensitivity of MALDI-MS detection of proteins bound to these elements surpassed that of other 2- and 3-dimensional substrates tested Immobilized trypsin retained functional (enzymatic) activity within the protein microchip and the specificity of macromolecular interactions even in complex biological samples. We believe that the underlying technology should therefore be extensible to whole-proteome protein expression profiling and interaction mapping.