An array of field-effect nanoplate SOI capacitors for (bio-)chemical sensing

An array of individually addressable nanoplate field-effect capacitive (bio-)chemical sensors based on an SOI (silicon-on-insulator) structure has been developed. The isolation of the individual capacitors was achieved by forming a trench in the top Si layer with a thickness of 350 nm. The realized sensor array allows addressable biasing and electrical readout of multiple nanoplate EISOI (electrolyte-insulator-silicon-on-insulator) capacitive biosensors on the same SOI chip as well as differential-mode measurements. The feasibility of the proposed approach has been demonstrated by realizing sensors for the pH and penicillin concentration detection as well as for the label-free electrical monitoring of polyelectrolyte multilayers formation and DNA (deoxyribonucleic acid)-hybridization event. A potential change of ～ 120 mV has been registered after the DNA hybridization for the sensor immobilized with perfectly matched single-strand DNA, while practically no signal changes have been observed for a sensor with fully mismatched DNA. The realized examples demonstrate the potential of the nanoplate SOI capacitors as a new basic structural element for the development of different types of field-effect biosensors.     

Field-effect sensors with charged macromolecules: characterisation by capacitance-voltage, constant-capacitance, impedance spectroscopy and atomic-force microscopy methods

Field-effect-based capacitive electrolyte-insulator-semiconductor (EIS) sensors have been utilised for the deoxyribonucleic acid (DNA) immobilisation and hybridisation detection as well as for monitoring the layer-by-layer adsorption of polyelectrolytes (anionic poly(sodium 4-styrene sulfonate) (PSS) and cationic poly(allylamine hydrochloride) (PAH)). The EIS sensors with charged macromolecules have been systematically characterised by capacitance-voltage, constant-capacitance, impedance spectroscopy and atomic-force microscopy methods. The effect of the number and polarity of the polyelectrolyte layers on the shift of the capacitance-voltage curves has been investigated. Alternating potential shifts of about 30-90 mV have been observed after the adsorption of each polyanion and polycation layer, respectively. The DNA immobilisation and hybridisation signals were 35-55 and 24-33 mV, respectively. The possible mechanisms for the sensor responses are discussed.     

Transient absorption and photovoltage study of' self-assembled bacteriorhodopsin/polycation multilayer films

A series of organized (PDAC/PM)(n) (poly(diallyldimethylammonium chloride)/purple membrane) multilayer films were prepared by alternate adsorptions of positively charged PDAC polyelectrolyte and negatively charged purple membrane (PM). The kinetics of the photocycle of bacteriorhodopsin (bR) in PM was studied by flash photolysis and transient photovoltage methods. Although the orientation of the adsorbed bR depends on the pH of the PM suspension, the kinetics of the photo-induced reaction cycle in dehydrated films is independent of the deposition pH. In dry (PDAC/PM)(n) films the decay of the M intermediate to the initial bR state is multiexponential and delayed to several minutes for both orientations. A simultaneous two-exponential decay in millisecond time domain was observed at red wavelengths. The source of the red-shifted absorption is suggested to be the C(610) intermediate of the cis photocycle of bR.     

Surface modification with poly(sulfobetaine methacrylate-co-acrylic acid) to reduce fibrinogen adsorption, platelet adhesion, and plasma coagulation

Zwitterionic sulfobetaine methacrylate (SBMA) polymers were known to possess excellent antifouling properties due to high hydration capacity and neutral charge surface. In this study, copolymers of SBMA and acrylic acid (AA) with a variety of compositions were synthesized and were immobilized onto polymeric substrates with layer-by-layer polyelectrolyte films via electrostatic interaction. The amounts of platelet adhesion and fibrinogen adsorption were determined to evaluate hemocompatibility of poly(SBMA-co-AA)-modified substrates. Among various deposition conditions by modulating SBMA ratio in the copolymers and pH of the deposition solution, poly(SBMA(56)-co-AA(44)) deposited at pH 3.0 possessed the best hemocompatibility. This work demonstrated that poly(SBMA-co-AA) copolymers adsorbed on polyelectrolyte-base films via electrostatic interaction improve hemocompatibility effectively and are applicable for various substrates including TCPS, PU, and PDMS. Furthermore, poly(SBMA-co-AA)-coated substrate possesses great durability under rigorous conditions. The preliminary hemocompatibility tests regarding platelet adhesion, fibrinogen adsorption, and plasma coagulation suggest the potential of this technique for the application to blood-contacting biomedical devices.     

The interplay between pH sensitivity and label-free protein detection in immunologically modified nano-scaled field-effect transistor

We present experimental results in order to establish a correlation between pH sensitivity of immunologically modified nano-scaled field-effect transistor (NS-ImmunoFET) with their sensing capacity for label-free detection. The NS-ImmunoFETs are fabricated from silicon-on-insulator (SOI) wafers and are fully-depleted with thickness of ~20 nm. The data shows that higher sensitivity to pH entails enhanced sensitivity to analyte detection. This suggests that the mechanism of analyte detection as pure electrostatic perturbation induced by antibody-analyte interaction is over simplified. The fundamental assumption, in existing models for field-effect sensing mechanism assumes that the analyte molecules do not directly interact with the surface but rather stand 'deep' in the solution and away from the dielectric surface. Recent studies clearly provide contradicting evidence demonstrating that antibodies lie down flat on the surface. These observations led us to propose that the proteins that cover the gate area intimately interact with active sites on the surface thus forming a network of interacting sites. Since sensitivity to pH is directly correlated with the amount of amphoteric sites, we witness a direct correlation between sensitivity to pH and analyte detection. The highest and lowest threshold voltage shift for a label-free and specific detection of 6.5 nM IgG were 40 mV and 2.3 mV for NS-ImmunoFETs with pH sensitivity of 35 mV/decade and 15 mV/decade, respectively. Finally, physical modeling of the NS-ImmunoFET is presented and charge of a single IgG protein at pH 6 is calculated. The obtained value is consistent with charge of IgG protein cited in literature.     

Immobilization of lutetium bisphthalocyanine in nanostructured biomimetic sensors using the LbL technique for phenol detection

This study describes the development of amperometric sensors based on poly(allylamine hydrochloride) (PAH) and lutetium bisphthalocyanine (LuPc(2)) films assembled using the Layer-by-Layer (LbL) technique. The films have been used as modified electrodes for catechol quantification. Electrochemical measurements have been employed to investigate the catalytic properties of the LuPc(2) immobilized in the LbL films. By chronoamperometry, the sensors present excellent sensitivity (20 nA μM(-1)) in a wide linear range (R(2)=0.994) up to 900 μM and limit of detection (s/n=3) of 37.5 × 10(-8)M for catechol. The sensors have good reproducibility and can be used at least for ten times. The work potential is +0.3 V vs. saturated calomel electrode (SCE). In voltammetry measurements, the calibration curve shows a good linearity (R(2)=0.992) in the range of catechol up to 500 μM with a sensitivity of 90 nA μM(-1) and LD of 8 μM.     

Inherent charge-shifting polyelectrolyte multilayer blends: a facile route for tunable protein release from surfaces

Recent research has highlighted degradable multilayer films that enable the programmed release of different therapeutics. Multilayers constructed by the layer-by-layer (LbL) deposition that can undergo disassembly have been demonstrated to be of considerable interest, particularly for biomedical surface coatings due to their versatility and mild aqueous processing conditions, enabling the inclusion of biologic drugs with high activity. In this study, we examine the controlled release of a protein using a different mechanism for film disassembly, the gradual dissociation of film interactions under release conditions. Poly(β-amino ester)s and poly(L-lysine) (PLL) were used as the positively charged multilayer components coassembled with a model negatively charged antigen protein, ovalbumin (Ova). The release of the protein from these multilayer films is dominated by the slow shift in the charge of components under physiological pH conditions rather than by hydrolytic degradative release. The time scale of release can be varied over almost 2 orders of magnitude by varying the ratio of the two polyamines in the deposition solution. The highly versatile and tunable properties of these films form a basis for designing controlled and sequential delivery of drug coatings using a variety of polyions.     

Aptamer based photoelectrochemical cytosensor with layer-by-layer assembly of CdSe semiconductor nanoparticles as photoelectrochemically active species

A label-free photoelectrochemical cytosensor for highly sensitive and specific detection of Ramos cell was developed based on photoactive films. The films were fabricated by a layer-by-layer (LBL) assembly of positively charged poly(dimethyldiallylammonium chloride) (PDDA) and negatively charged CdSe semiconductor nanoparticles (NPs) capped with mercaptoacetic acid. The resulting modified electrodes were tested as sensors for Ramos cell through the recognition of DNA aptamer which was covalently bound to the electrode using the classic coupling reactions between -COOH groups on the surfaces of CdSe NPs and -NH(2) groups of the aptamer. The newly developed cytosensor exhibited excellent sensitivity and selectivity. The linear range was from 160 to 1600 cells/mL and the detection limit was 84 cells/mL.     

The open container-used microfluidic chip using IrO(x) ultramicroelectrodes for the in situ measurement of extracellular acidification

The measurement of metabolic activity based on the extracellular acidification rate has attracted wide interests in the field of biochemical detection. In the study, the chip comprising a microfluid-controlled open container and iridium oxide (IrO(x)) pH ultramicroelectrodes (UMEs) was constructed for the purpose of in situ measurement of extracellular acidification rate. The feasible anodic depositing parameters of IrO(x) film were in the range of +0.53 to +0.8 V by means of exploring the electrochemical properties of alkaline Ir(IV) deposition solution. The IrO(x) pH UMEs electrodeposited for 300 cycles between 0 V and +0.6 V exhibited the near-super-Nernstian sensitivity of -68 to -76 mV/pH and the good stability with potential drifting of 11.7 mV within 24h. The design of the open container connected with a position-raised microchannel improved the sensing stability of IrO(x) pH UMEs, with the potential deviation of as low as 0.1 mV under the flow rate of 20 μl/min. The acidification rate of HeLa cells (2160 cells/mm(2)) repeatedly measured 5 times in the microfluidic chip showed the good reproducibility of 0.021±0.002 pH/min. Moreover, the chip can decrease the acidosis occurrence, a decrease of only 0.13-0.17 pH unit in 8 min interval, during the measurement of cellular metabolic activity.     

Cl- sensitive biosensor used electrolyte-solution-gate diamond FETs

We have investigated the electrolyte-solution-gate field effect transisitors (SGFETs) used hydrogen terminated (H-terminated) or partially oxygen terminated (O-terminated) polycrystalline diamond surface in the Cl- and Br- ionic solutions. The H-terminated channel SGFETs are insensitive to pH values in electrolyte solutions. The threshold voltages of the diamond SGFETs shift according to the density of Cl- and Br- ions about 30 mV/decade. One of the attractive biomedical applications for the Cl- sensitive SGFETs is the detection of chloride density in blood or in sweat especially in the case of cystic fibrosis. The sensitivities of Cl- and Br- ions have been lost on the partially O-terminated diamond surface. These phenomena can be explained by the polarity of surface change on the H-terminated and the O-terminated surface.     

Polypeptide multilayer film co-delivers oppositely-charged drug molecules in sustained manners

The current state-of-the-art for drug-carrying biomedical devices is mostly limited to those that release a single drug. Yet there are many situations in which more than one therapeutic agent is needed. Also, most polyelectrolyte multilayer films intended for drug delivery are loaded with active molecules only during multilayer film preparation. In this paper, we present the integration of capsules as vehicles within polypeptide multilayer films for sustained release of multiple oppositely charged drug molecules using layer-by-layer nanoassembly technology. Calcium carbonate (CaCO(3)) particles were impregnated with polyelectrolytes, shelled with polyelectrolyte multilayers, and then assembled onto polypeptide multilayer films using glutaraldehyde. Capsule-integrated polypeptide multilayer films were obtained after decomposition of CaCO(3) templates. Two oppositely charged drugs were loaded into capsules within polypeptide multilayer films postpreparation based on electrostatic interactions between the drugs and the polyelectrolytes impregnated within capsules. We determined that the developed innovative capsule-integrated polypeptide multilayer films could be used to load multiple drugs of very different properties (e.g., opposite charges) any time postpreparation (e.g., minutes before surgical implantation inside an operating room), and such capsule-integrated films allowed simultaneous delivery of two oppositely charged drug molecules and a sustained (up to two weeks or longer) and sequential release was achieved.     

Optical and electrochemical detection of saccharides with poly(aniline-co-3-aminobenzeneboronic acid) prepared from enzymatic polymerization

Boronic acid-based sensors for saccharides have been developed via biocatalysis. The self-doped copolymer of poly(aniline-co-3-aminobenzeneboronic acid) [poly(aniline-co-AB)], with various mole ratios of two components, was synthesized by oxidative enzymatic polymerization using a natural biocatalyst such as horseradish peroxidase together with an anionic polyelectrolyte template (sulfonated polystyrene) under mild conditions (pH 4.5). Poly(aniline-co-AB), having an aniline boronic acid-to-aniline ratio of 1:2 on average, gave rise to a green doped polymer with absorption maxima at 745 nm. The potentiometric detection of saccharides using poly(aniline-co-AB) is presented. Characteristics of both transient and steady-state response associated with the complex formation of poly(aniline-co-AB) with various saccharides were monitored by UV-vis spectroscopy and cyclic voltammetry (CV). The results obtained from UV-vis spectroscopy and CV show that the sensitivity of enzymatically synthesized water-soluble poly(aniline-co-AB) for various saccharides was improved significantly compared to the chemically synthesized counterpart. A possible mechanism for the sensitive detection of sugar molecules by boronic acid is proposed on the basis of UV-vis and IR spectrophotometry, and four-point probe conductivity measurements.     

Extended-gate FET-based enzyme sensor with ferrocenyl-alkanethiol modified gold sensing electrode

We developed a field-effect transistor (FET)-based enzyme sensor that detects an enzyme-catalyzed redox-reaction event as an interfacial potential change on an 11-ferrocenyl-1-undecanethiol (11-FUT) modified gold electrode. While the sensitivity of ion-sensitive FET (ISFET)-based enzyme sensors that detect an enzyme-catalyzed reaction as a local pH change are strongly affected by the buffer conditions such as pH and buffer capacity, the sensitivity of the proposed FET-based enzyme sensor is not affected by them in principle. The FET-based enzyme sensor consists of a detection part, which is an extended-gate FET sensor with an 11-FUT immobilized gold electrode, and an enzyme reaction part. The FET sensor detected the redox reaction of hexacyanoferrate ions, which are standard redox reagents of an enzymatic assay in blood tests, as a change in the interfacial potential of the 11-FUT modified gold electrode in accordance with the Nernstian response at a slope of 59 mV/decade at 25 degrees C. Also, the FET sensor had a dynamic range of more than five orders and showed no sensitivity to pH. A FET-based enzyme sensor for measuring cholesterol level was constructed by adding an enzyme reaction part, which contained cholesterol dehydrogenase and hexacyanoferrate (II)/(III) ions, on the 11-FUT modified gold electrode. Since the sensitivity of the FET sensor based on potentiometric detection was independent of the sample volume, the sample volume was easily reduced to 2.5 microL while maintaining the sensitivity. The FET-based enzyme sensor successfully detected a serum cholesterol level from 33 to 233 mg/dL at the Nernstian slope of 57 mV/decade.     

The modification of enzyme electrode properties with non-conducting electropolymerised films

Phenol and several phenol derivatives have been electropolymerised on to platinum anodes. The selective properties of the modified electrodes were dependent on the final polymeric structure. Although essentially non-conducting, dual phenolic films could be deposited on electrode surfaces. This was achieved by the initial deposition of a porous polymer formed from, phenol red, followed by the more diffusion limiting film of oxidised phenol. The resulting composite film showed the combined selective characteristics of the two component polymers. Attempts to enhance polymeric film selectivity via the incorporation of charged or neutral surfactants are outlined. The characteristics of glucose oxidase incorporated into (poly)phenol films are discussed.     

Morphological and optical characterization of polyelectrolyte multilayers incorporating nanocrystalline cellulose

Aqueous layer-by-layer (LbL) processing was used to create polyelectrolyte multilayer (PEM) nanocomposites containing cellulose nanocrystals and poly(allylamine hydrochloride). Solution-dipping and spin-coating assembly methods gave smooth, stable, thin films. Morphology was studied by atomic force microscopy (AFM) and scanning electron microscopy (SEM), and film growth was characterized by X-ray photoelectron spectroscopy (XPS), ellipsometry, and optical reflectometry. Relatively few deposition cycles were needed to give full surface coverage, with film thicknesses ranging from 10 to 500 nm. Films prepared by spin-coating were substantially thicker than solution-dipped films and displayed radial orientation of the rod-shaped cellulose nanocrystals. The relationship between film color and thickness is discussed according to the principles of thin film interference and indicates that the iridescent properties of the films can be easily tailored in this system.     

Influence of polyelectrolyte multilayer films on the ICAM-1 expression of endothelial cells

Recently, the use of polyelectrolyte films has been suggested as a new versatile technique of surface modification aimed at tissue engineering. In the present study, we evaluated the expression of intercellular adhesion molecule (ICAM)-1 of endothelial cells (ECs) seeded on two types of polyelectrolyte multilayer films either terminated by poly(D-lysine) (PDL) or poly(allylamine hydrochloride) (PAH). This work showed that chemical stimulations with tumor necrosis factor (TNF)-alpha induced the ICAM-1 expression of ECs differently depending largely on the film architecture employed. Compared with PAH-ending films, the PDL-ending ones upregulated the ICAM-1 expression of the ECs after a prolonged exposition to TNF-alpha, rendering this film type less favorable in tissue engineering. Cytochalasin D (an F-actin disrupting agent) showed the involvement of the cytoskeleton in the upregulation of ICAM-1 for cells deposited on films terminated by PDL. The PAH-ending films did not perturb the ICAM-1 expression of ECs and might thus enhance the seeding of ECs in vascular engineering.     

Protection of sensors for biological applications by photoinitiated chemical vapor deposition of hydrogel thin films

We report photoinitiated chemical vapor deposition (piCVD), a gentle synthetic method for the preparation of ultrathin films (approximately 100 nm) of the hydrogel poly(hydroxyethyl methacrylate) (pHEMA). piCVD occurs near room temperature and requires only mild vacuum conditions. The deposited films swell rapidly and reversibly in buffer solution, and the swelling properties can be controlled via the deposition conditions. Analysis of the swelling data indicates that the mesh size of the hydrogel creates a selectively permeable coating. The mesh is large enough to allow small molecule analytes to permeate the film but small enough to prevent the transport of large biomolecules such as proteins. X-ray photoelectron spectroscopy (XPS) shows that the films decrease nonspecific adhesion of the protein albumin by nearly 8-fold over bare silicon. A dry process, piCVD is suitable for coating particles with diameters as small as 5 microm. The absence of solvents and plasmas in piCVD allows films to be directly synthesized on optode sensors without degradation of sensitivity or response time.     

pH-responsive properties of multilayered poly(L-lysine)/hyaluronic acid surfaces

Multilayer films have been prepared by the sequential electrostatic adsorption of poly(L-lysine) and hyaluronic acid onto charged silicon surfaces from dilute aqueous solutions under various pH conditions. Microelectrophoresis was used to examine the local acid-base equilibria of the polyelectrolytes within the films as a function of the total number of layers in the film and the assembly solution pH. The acid-base dissociation constants were observed to deviate significantly from dilute solution values upon adsorption, to be layer dependent only within the first 3-4 layers, and to show sensitivity to the assembly solution pH. As a result, some of the physicochemical properties of the films have also been found to exhibit pH-responsive behavior. For example, the thickest films result when at least one of the polyelectrolytes is only partially dissociated in solution. As well, the pH-dependent degree of dissociation of the surface functional groups can be used to vary the contact angle of a water droplet by as much as 25 degrees and the coefficient of friction by up to an order of magnitude. In addition, the extent to which PLL/HA films can be made to swell in solution can be varied by a factor of 7 depending on the assembly solution and swelling solution pH. The anomalies found in the dissociation constants account for the trends in these pH-dependent properties. Here, we demonstrate that knowledge of the acid-base dissociation behavior in multilayer films is key to understanding and controlling the physical properties of the films, particularly surface friction and wettability, which are fundamentally important factors for many biomaterials applications. For example, we outline a mechanism whereby biopolymer thin films can be electrostatically adsorbed under highly charged "sticky" conditions and then quickly transformed into stable low-friction films simply by altering the pH environment.     

Protein adsorption onto auto-assembled polyelectrolyte films

Surface modification by deposition of ordered protein systems constitutes one of the major objectives of bio-related chemistry and biotechnology. In this respect a concept has recently been reported aimed at fabricating multilayers by the consecutive adsorption of positively and negatively charged polyelectrolytes. We investigate the adsorption processes between polyelectrolyte multilayers and a series of positively and negatively charged proteins. The film buildup and adsorption experiments were followed by Scanning Angle Reflectometry (SAR). We find that proteins strongly interact with the polyelectrolyte film whatever the sign of the charge of both the multilayer and the protein. When charges of the multilayer and the protein are similar, one usually observes the formation of protein monolayers, which can become dense. We also show that when the protein and the multilayer become oppositely charged, the adsorbed amounts are usually larger and the formation of thick protein layers extending up to several times the largest dimension of the protein can be observed. Our results confirm that electrostatic interactions dominate protein/polyelectrolyte multilayer interactions.     

pH-Amplified multilayer films based on hyaluronan: influence of HA molecular weight and concentration on film growth and stability

In this study, we investigate the growth and internal properties of polyelectrolyte multilayer films made of poly(l-lysine) and hyaluronan (PLL/HA) under pH-amplified conditions, that is, by alternate deposition of PLL at high pH and HA at low pH. We focus especially on the influence of the molecular weight of HA in this process as well as on its concentration in solution. Film growth was followed by quartz crystal microbalance and by infrared spectroscopy to quantify the deposited mass and to characterize the internal properties of the films, including the presence of hydrogen bonds and the ionization degree of HA in the films. Film growth was significantly faster for HA of high molecular weight (1300 kDa) as compared with 400 and 200 kDa. PLL was found to exhibit a random structure once deposited in the films. Furthermore, we found that PLL-ending films are more stable when they are placed in PBS than their HA counterparts. This was explained on the basis of more cohesive interactions in the films for PLL-ending films. Finally, we quantified PLL(FITC) diffusion into the films and observed that PLL diffusion is enhanced when PLL is paired with the HA of high MW. All together, these results suggest that besides purely physicochemical parameters such as variation in pH, the molecular weight of HA, its concentration in solution, and the possibility to form intermolecular HA association play important roles in film growth, internal cohesion, and stability.