Comparative differential scanning calorimetric analysis of vegetable oils: II. Effects of cooling rate variation

The effects of scanning rates (1, 5, 10 and 20 degrees C/min) on the DSC cooling profiles of 11 vegetable oils have been determined in order to monitor peak transition temperatures, onset temperatures and crystallisation enthalpies. Triacylglycerol (TAG) profiles and iodine value analyses were used to complement the DSC data. The melted samples exhibited complicated crystallising exotherms. As the cooling rate increased, the crystallisation temperature decreased and the breadth of the crystallisation exotherm on cooling from the melt increased. In addition, the intensity of the exothermic peak increased somewhat when the cooling rate was increased. At slow cooling rates, TAG had more time to interact. It is conceivable that, at a low cooling rate (1 degree C/min), a prominent exotherm would be observed on crystallisation of vegetable oils and fats. The occurrence of one exotherm upon cooling indicated the co-crystallisation of the TAG upon slow cooling. On the basis of the corollary results obtained, vegetable oils may be differentiated by their onset temperature (Ton) values in the DSC cooling curves. Generally, there was a shift of Ton toward lower values with increasing cooling rates.     

Effect of Milling on DSC Thermogram of Excipient Adipic Acid

The purpose of this research was to investigate why and how mechanical milling results in an unexpected shift in differential scanning calorimetry (DSC) measured fusion enthalpy (∆_fus H) and melting point (T _m) of adipic acid, a pharmaceutical excipient. Hyper differential scanning calorimetry (hyper-DSC) was used to characterize adipic acid before and after ball-milling. An experimental study was conducted to evaluate previous postulations such as electrostatic charging using the Faraday cage method, crystallinity loss using powder X-ray diffraction (PXRD), thermal annealing using DSC, impurities removal using thermal gravimetric analysis (TGA) and Karl Fischer titration. DSC thermograms showed that after milling, the values of ∆_fus H and T _m were increased by approximately 9% and 5 K, respectively. Previous suggestions of increased electrostatic attraction, change in particle size distribution, and thermal annealing during measurements did not explain the differences. Instead, theoretical analysis and experimental findings suggested that the residual solvent (water) plays a key role. Water entrapped as inclusions inside adipic acid during solution crystallization was partially evaporated by localized heating at the cleaved surfaces during milling. The correlation between the removal of water and melting properties measured was shown via drying and crystallization experiments. These findings show that milling can reduce residual solvent content and causes a shift in DSC results.     

Microscopy and calorimetry as complementary techniques to analyze sugar crystallization from amorphous systems

A comparison of microscopic and macroscopic techniques to evaluate sugar crystallization kinetics is presented using amorphous lactose and lactose-trehalose mixtures. Polarized light video microscopy (PLV) and differential scanning calorimetry (DSC) were applied to measure crystallization kinetics, induction times and time for complete sugar crystallization at different storage temperatures (60-95 degrees C). DSC was also employed to measure the glass transition temperature (T(ag)) of the systems. PLV permitted direct observation, in real time, of growth of individual crystals and morphological aspects at a scale not detected by DSC. Taking the average of several microscopic observations, the results for temperature dependence of crystallization rate and time to complete lactose crystallization were similar to those obtained by DSC. Both PLV and DSC techniques showed that the presence of trehalose delayed lactose crystallization, without affecting the T(ag) value. For the analysis of sugar crystallization in amorphous systems, PLV and DSC proved to be complementary techniques. Validation of results obtained by PLV with results from DSC opens a new area of microstructural analysis of crystallizing systems.     

Characterization of the hidden glass transition of amorphous cyclomaltoheptaose

An amorphous solid of cyclomaltoheptaose (β-cyclodextrin, β-CD) was formed by milling its crystalline form using a high-energy planetary mill at room temperature. The glass transition of this amorphous solid was found to occur above the thermal degradation point of the material preventing its direct observation and thus its full characterization. The corresponding glass transition temperature (T_g) and the ΔC_p at T_g have, however, been estimated by extrapolation of T_g and ΔC_p of closely related amorphous compounds. These compounds include methylated β-CD with different degrees of substitution and molecular alloys obtained by co-milling β-CD and methylated β-CD (DS 1.8) at different ratios. The physical characterization of the amorphous states have been performed by powder X-ray diffraction and differential scanning calorimetry, while the chemical integrity of β-CD upon milling was checked by NMR spectroscopy and mass spectrometry.     

Amorphous trehalose dihydrate by cryogenic milling

Trehalose dihydrate is a safe, naturally occurring disaccharide used as a food ingredient and pharmaceutical excipient. It has been reported that room temperature milling does not lead to the formation of amorphous trehalose dihydrate. This paper reports the behaviour of trehalose dihydrate upon milling at cryogenic temperatures as studied by DSC, TGA, XRPD and Raman spectroscopy. We have demonstrated that the crystal to glass transformation for trehalose dihydrate is possible using cryogenic milling. This is the first reported example of cryogenic milling (a mild and widely applicable technique) applied to generating amorphous hydrates.     

Manifestation of the size effect during crystallization and melting of dispersed water in native and amorphous starches with various degrees of hydration

Differential scanning calorimetry (DSC) was used to study the melting and crystallization of frozen water dispersed in humid potato starch. Melting and crystallization temperatures and heats as functions of the degree of hydration of the starch were obtained for native and amorphous starch states. Manifestations of the size effect were observed in the dependences of heat for the processes in both starch states. Crystallization and melting heats of frozen water were found to change nonlinearly with the increasing degree of hydration in all cases. In contrast, a size effect in the dependences of melting and crystallization temperatures of frozen water was detected only for native starch. Reasons responsible for the absence of a size effect in the amorphous state were considered. Hysteresis, which is characteristic of small particles, was observed upon melting and crystallization of frozen water and its manifestation strongly differed in the native and amorphous states of potato starch.     

Glass transition temperatures and water sorption isotherms of cassava starch

The effect of water content on the glass transition temperatures of cassava starch was determined by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). Samples were transformed to the amorphous state by compression molding at high temperature (as demonstrated by wide angle X-ray diffraction, WAXS), and then the samples were moisture conditioned. Both DSC and DMTA showed that water anti-plasticized cassava starch at lower moisture contents, and plasticized it at higher water contents. Samples with higher moisture contents stored at room temperature, 45 °C and 80 °C underwent retrogradation as indicated by WAXS. Sorption isotherms of cassava starch showed that for a_w values lower than around 0.85, the sorption capacity decreased with increasing temperature; while the opposite behavior was observed at a_w > 0.85. This inversion point (a_w = 0.85) was attributed to the fact that more active sites were exposed to the adsorption processes, due to the enhanced molecular mobility promoted in the amorphous regions by starch crystallization.     

Influence of low-temperature nucleation on the crystallization process of poly(L-lactide)

The crystallization kinetics of poly(l-lactide), PLLA, is slow enough to allow a quasi-amorphous polymer to be obtained at low temperature simply by quenching from the melt. The PLLA crystallization process was followed by differential scanning calorimetry and optical microscopy after nucleation isothermal treatments at temperatures just below (53 degrees C) and just above (73 degrees C) the glass transition temperature. The crystallization exotherm shown in the heating thermograms shifts toward lower temperatures as the annealing time at 73 degrees C increases. The same effect is shown to a lesser extent when the sample nucleates at 53 degrees C, showing the ability to nucleate in the glassy state, already shown in other polymers. The shape of the DSC thermograms is modeled by using Avrami's theory and allows an estimation of the number of crystallization germs formed. The results of optical microscopy are converted to thermograms by evaluating the average gray level of the image recorded in transmission mode as a function of temperature and calculating its temperature derivative. The shape of such optical thermograms is quite similar to that of the DSC traces but shows some peculiarities after long nucleation treatments. Atomic force microscopy was used to analyze the crystal morphology and is an additional proof of the effect of nucleation in the glassy state. The crystalline morphology observed in samples crystallized after nucleation in the glassy state is qualitatively different from that of samples nucleated above the glass transition temperature, and the number of crystals seems to be much greater than what could be expected from the crystallization kinetics.     

Comparative differential scanning calorimetric analysis of vegetable oils: I. Effects of heating rate variation

The melting curves of 11 vegetable oils have been characterised. Vegetable oil samples that were cooled at a constant rate (5 degrees C/min) from the melt showed between one and seven melting endotherms upon heating at four different heating rates (1, 5, 10 and 20 degrees C/min) in a differential scanning calorimeter (DSC). Triacylglycerol (TAG) profiles and iodine value analyses were used to complement the DSC data. Generally, the melting transition temperature shifted to higher values with increased rates of heating. The breadth of the melting endotherm and the area under the melting peak also increased with increasing heating rate. Although the number of endothermic peaks was dependent on heating rate, the melting curves of the oil samples were not straightforward in that there was no correlation between the number of endothermic peaks and heating rates. Multiple melting behaviour in DSC experiments with different heating rates could be explained by: (1) the melting of TAG populations with different melting points; and (2) TAG crystal reorganisation effects. On the basis of the corollary results obtained, vegetable oils and fats may be distinguished from their offset-temperature (Toff) values in the DSC melting curves. The results showed that Toff values of all oil samples were significantly (p < 0.01) different in the melting curves scanned at four different scanning rates. These calorimetric results indicate that DSC is a valuable technique for studying vegetable oils.     

Trehalose amorphization and recrystallization

The stability of the amorphous trehalose prepared by using several procedures is presented and discussed. Amorphization is shown to occur by melting (T(m)=215 degrees C) or milling (room temperature) the crystalline anhydrous form TRE-beta. Fast dehydration of the di-hydrate crystalline polymorph, TRE-h, also produces an amorphous phase. Other dehydration procedures of TRE-h, such as microwave treatment, supercritical extraction or gentle heating at low scan rates, give variable fractions of the polymorph TRE-alpha, that undergo amorphization upon melting (at lower temperature, T(m)=130 degrees C). Additional procedures for amorphization, such as freeze-drying, spray-drying or evaporation of trehalose solutions, are discussed. All these procedures are classified depending on the capability of the undercooled liquid phase to undergo cold crystallization upon heating the glassy state at temperatures above the glass transition temperature (T(g)=120 degrees C). The recrystallizable amorphous phase is invariably obtained by the melt of the polymorph TRE-alpha, while other procedures always give an amorphous phase that is unable to crystallize above T(g). The existence of two different categories is analyzed in terms of the transformation paths and the hypothesis that the systems may exhibit different molecular mobilities.     

Physicochemical and structural characteristics of chitosan nanopowders prepared by ultrafine milling

Two different molecular weights of chitosan were pulverized to nanopowders by ultrafine milling. The nanopowders were characterized by viscometry small angle X-ray scattering (SAXS), transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), FT-IR spectroscopy and UV-vis spectroscopy. Our results showed that ultrafine milling effectively reduced the particle size of chitosan to a nanoscale. The viscosity average molecular weight (Mv) of chitosan was decreased by the milling treatment. The crystalline structure of chitosan was destroyed by the milling since the nanopowder exhibited an amorphous XRD pattern. In addition, thermal stability of the low molecular weight chitosan was decreased after the milling treatment. FT-IR and UV-vis spectra showed that the milling process did not cause significant changes in the chemical structure of chitosan.     

Evaluation of the stability of creatine in solution prepared from effervescent creatine formulations

The objectives of this study were to determine the cause of the crystallization in a large volume creatine supplement solution made from effervescent powders containing di-creatine citrate, and to characterize these crystals using thermal analyses and x-ray diffractometry. Creatine effervescent powders were dissolved in deionized water (pH 6.2) and stored both at room temperature (RT) (25°C) and refrigerated condition (4°C) over a period of 45 days. Creatine concentration was determined using high-performance liquid chromatography (HPLC). Intrinsic dissolution and saturated solubility of creatine, creatine monohydrate, and di-creatine citrate in water were determined and compared. Crystal growth was detected only in the refrigerated samples on the seventh day of storage. Differential Scanning Calorimetry (DSC) and x-ray diffraction (XRD) studies revealed that the crystals formed were of creatine monohydrate. Ninety percent creatine degradation was observed within 45 days for RT samples. However, at refrigerated condition this degradation was 80% within the same time period. The pH of the RT samples also increased from 3.6 to 4.5 during storage. No such increase was observed in the case of refrigerated samples. The intrinsic dissolution rate constants of the compounds decreased in the following order: dicreatine citrate>creatine>creatine monohydrate. In conclusion, di-creatine citrate used in effervescent formulation dissociates to creatine in aqueous solution and eventually crystallizes out as creatine monohydrate. Significant decrease in solubility and effect of pH contribute to this crystallization process.     

Devitrification of amorphous celecoxib

The purpose of this research was to analyze the devitrification of amorphous celecoxib (CEL) in the presence of different stressors (temperature, pressure, and/or humidity) encountered during processing of solid dosage forms. Amorphous CEL was prepared in situ in the analytical instruments, as well as in laboratory, by quench-cooling of melt process, and analyzed by dynamic mechanical thermal analysis, differential scanning calorimetry, microscopy, and Fourier-transform infrared spectroscopy. Amorphous CEL prepared in situ in the analytical instruments was resistant to crystallization under the influence of temperature and/or pressure, because of its protection from the external environment during preparation. These samples exhibited structural relaxation during annealing at 25°C/0% relative humidity (RH) for 16 hours. Generation of amorphous CEL in the laboratory resulted in partially crystalline samples, because of exposure to environmental temperature and humidity, resulting in incomplete vitrification. Subjection to thermal stress favored crystallization of amorphous CEL into metastable polymorphic forms, which were not obtained by solvent recrystallization approach. Temperature and humidity were identified as the major factors promoting devitrification of amorphous CEL, leading to loss of solubility advantage. Exposure to International Conference on Harmonization-specified accelerated stability storage conditions (40°C/75% RH) resulted in complete devitrification of amorphous CEL within 15 days. The phase-transformation process of amorphous CEL along the temperature scale was examined visually, as well as spectrally. This propensity for devitrification of amorphous CEL seemed to depend on the strength of differential molecular interactions between the amorphous and crystalline form.     

A Method to Evaluate the Effect of Contact with Excipients on the Surface Crystallization of Amorphous Drugs

Amorphous drugs are used to improve the solubility, dissolution, and bioavailability of drugs. However, these metastable forms of drugs can transform into more stable, less soluble, crystalline counterparts. This study reports a method for evaluating the effect of commonly used excipients on the surface crystallization of amorphous drugs and its application to two model amorphous compounds, nifedipine and indomethacin. In this method, amorphous samples of the drugs were covered by excipients and stored in controlled environments. An inverted light microscope was used to measure in real time the rates of surface crystal nucleation and growth. For nifedipine, vacuum-dried microcrystalline cellulose and lactose monohydrate increased the nucleation rate of the β polymorph from two to five times when samples were stored in a desiccator, while d-mannitol and magnesium stearate increased the nucleation rate 50 times. At 50% relative humidity, the nucleation rates were further increased, suggesting that moisture played an important role in the crystallization caused by the excipients. The effect of excipients on the crystal growth rate was not significant, suggesting that contact with excipients influences the physical stability of amorphous nifedipine mainly through the effect on crystal nucleation. This effect seems to be drug specific because for two polymorphs of indomethacin, no significant change in the nucleation rate was observed under the excipients.KEY WORDS: amorphous, drugs, growth rate, nucleation rate, tablet excipients     

Effects of Potassium Chloride and Sodium Chloride on the Thermal Properties of Gellan Gum Gels

The exothermic and endothermic peaks in cooling and heating curves of differential scanning calorimetry (DSC) for gellan gum gels without and with potassium chloride and sodium chloride were analyzed. The gelling and melting temperatures shifted to higher temperatures with increasing gellan and salt concentration in the concentration range of gellan from 0.3 to 2.0% (w/w). The exothermic and endothermic enthalpy increased with increasing gellan and salt concentrations. Cooling DSC curves showed one exothermic peak for samples with salts and at low gellan concentration. Heating DSC curves showed many peaks for all samples except 0.3% (w/w) gellan gum gels. The sol-gel transition of samples was examined numerically by using a zipper model approach. The introduction of cations increases the number of junction zones or zippers and decreases the rotational freedom of parallel links. This makes the structure of junction zones more heat resistant, and increases the elastic modulus of the gel.     

Thermal properties of ethylene glycol aqueous solutions

Preventing ice crystallization by transforming liquids into an amorphous state, vitrification can be considered as the most suitable technique allowing complex tissues, and organs cryopreservation. This process requires the use of rapid cooling rates in the presence of cryoprotective solutions highly concentrated in antifreeze compounds, such as polyalcohols. Many of them have already been intensively studied. Their glass forming tendency and the stability of their amorphous state would make vitrification a reality if their biological toxicity did not reduce their usable concentrations often below the concentrations necessary to vitrify organs under achievable thermal conditions. Fortunately, it has been shown that mixtures of cryoprotectants tend to reduce the global toxicity of cryoprotective solutions and various efficient combinations have been proposed containing ethanediol. This work reports on the thermal properties of aqueous solutions with 40, 43, 45, 48, and 50% (w/w) of this compound measured by differential scanning calorimetry. The glass forming tendency and the stability of the amorphous state are evaluated as a function of concentration. They are given by the critical cooling rates v(ccr)above which ice crystallization is avoided, and the critical warming rates v(cwr) necessary to prevent ice crystallization in the supercooled liquid state during rewarming. Those critical rates are calculated using the same semi-empirical model as previously. This work shows a strong decrease of averaged critical cooling and warming rates when ethanediol concentration increases, V(ccr) and V(cwr) = 1.08 x 10 (10) K/min for 40% (w/w) whereas V(ccr) = 11 and V(cwr) = 853 K/min for 50% (w/w). Those results are compared with the corresponding properties of other dialcohols obtained by the same method. Ethylene glycol efficiency is between those of 1,2-propanediol and 1,3-propanediol.     

Mediation of deep supercooling of peach and dogwood by enzymatic modifications in cell-wall structure

Treatment of stem sections of peach (Prunus persica (L.) Batsch) and flowering dogwood (Cornus florida L.) with macerase, an enzyme mixture rich in pectinase, for 24–48 h resulted in a complete flattening of the low-temperature exotherm (LTE) as determined by differential thermal analysis (DTA). Ultrastructural analysis of macerase-treated tissue demonstrated a nearly complete digestion of the pit membrane (black cap and primary cell-wall) of nearly 100% of the xylem-parenchyma cells examined after 48 h of exposure to the enzyme. Additionally, the underlying amorphous layer was partially degraded in up to 57% of the cells examined. The macerase treatment had no visible effect on secondary cell-walls of xylem tissue. In contrast, treatment of stem tissue with cellulysin (mostly cellulase) resulted in a shift of the LTE to warmer temperatures as determined by DTA, and a digestion of only the outermost layer of the pit membrane in nearly 100% of the cells examined, with little or no effect on the underlying layers. Treatment of tissue with 25 mM sodiumphosphate buffer also resulted in a shift of the LTE to warmer temperatures but the shift was not as great as in cellulysin-treated tissue. The shift was associated with a partial degradation of the outermost layer of the pit membrane in dogwood (33–45% of the cells examined) but not in peach (3–7% of the cells). Collectively, the data indicate that pectins may be an integral structural element of the pit membrane and that this portion of the cell-wall, along with the underlying amorphous layer, play a major role in forming a barrier to water movement and growth of ice crystals. This barrier allows xylem parenchyma of some species of woody plants to undergo deep supercooling.Abbreviations DTA Differential thermal analysis - HTE high-temperature exotherm - LTE low-temperature exotherm     

Review of biomaterial thermal property measurements in the cryogenic regime and their use for prediction of equilibrium and non-equilibrium freezing applications in cryobiology

It is well accepted in cryobiology that the temperature history and cooling rates experienced in biomaterials during freezing procedures correlate strongly with biological outcome. Therefore, heat transfer measurement and prediction in the cryogenic regime is central to the field. Although direct measurement of temperature history (i.e. heat transfer) can be performed, accuracy is usually achieved only for local measurements within a given system and cannot be readily generalized to another system without the aid of predictive models. The accuracy of these models rely upon thermal properties which are known to be highly dependent on temperature, and in the case of significant cryoprotectant loading, also on crystallized fraction. In this work, we review the available thermal properties of biomaterials in the cryogenic regime. The review shows a lack of properties for many biomaterials in the subzero temperature domain, and especially for systems with cryoprotective agents. Unfortunately, use of values from the limited data available (usually only down to −40 °C) lead to an underestimation of thermal property change (i.e. conductivity rise and specific heat drop due to ice crystallization) with lower temperatures. Conversely, use of surrogate values based solely on ice thermal properties lead to an overestimation of thermal property change for most biomaterials. Additionally, recent work extending the range of available thermal properties to −150 °C has shown that the thermal conductivity will drop in both PBS and tissue (liver) due to amorphous/glassy phases (versus crystalline) of biomaterials with the addition of cryoprotective additives such as glycerol. Thus, we investigated the implications of using approximated or constant property values versus measured temperature-dependent values for predicting temperature history during freezing in PBS (phosphate-buffered saline) and porcine liver with and without cryoprotectants (glycerol). Using measured property values (thermal conductivity, specific heat, and latent heat of phase change) of porcine liver, a standard was created which showed that values based on surrogate ice properties under-predicted cooling times, while constant properties (i.e. based on limited data reported near the freezing point) over-predicted cooling times. Additionally, a new iterative numerical method that accommodates non-equilibrium cooling effects as a function of time and position (i.e. crystallization versus amorphous phase) was used to predict temperature history during freezing in glycerol loaded systems. Results indicate that in addition to the increase in cooling times due to the lowering of thermal diffusivity with more glycerol, non-equilibrium effects such as the prevention of maximal crystallization (i.e. amorphous phases) will further increase required cooling times. It was also found that the amplified effect of non-equilibrium cooling and crystallization with system size prevents the thermal history to be described with non-dimensional lengths, such as was possible under equilibrium cooling. These results affirm the need to use accurate thermal properties that incorporate temperature dependence and crystallized fraction. Further studies are needed to extract thermal properties of other important biomaterials in the subzero temperature domain and to develop accurate numerical methods which take into account non-equilibrium cooling events encountered in cryobiology when partial or total vitrification occurs.     

The mechanism of freezing injury in xylem of winter apple twigs

In acclimated winter twigs of Haralson apple (Pyrus Malus L.), a lag in temperature during cooling at a constant rate was observed at about −41 C by differential thermal analysis. The temperature at which this low temperature exotherm occurred was essentially unaffected by the cooling rate. During thawing there was no lag in temperature (endotherm) near the temperature at which the low temperature exotherm occurred, but upon subsequent refreezing the exotherm reappeared at a somewhat higher temperature when twigs were rewarmed to at least −5 C before refreezing. These observations indicate that a small fraction of water may remain unfrozen to as low as −42 C after freezing of the bulk water in stems. The low temperature exotherm was not present in twigs freeze-dried to a water content below 8.5% (per unit fresh weight), but it reappeared when twigs were rehydrated to 20% water. When freeze-dried twigs were ground to a fine powder prior to rehydration, no exotherm was observed. Previous work has shown that the low temperature exotherm arises from xylem and pith tissues, and that injury to living cells in these tissues invariably occurs only when twigs are cooled below, but not above the temperature of the low temperature exotherm. This study revealed that the low temperature exotherm resulted from the freezing of a water fraction, that the freezing of this water was independent of the freezing of the bulk water, that the exotherm was associated with some gross structural feature but not the viability of the tissue, and that injury to living cells in the xylem and pith was closely and perhaps causally related to the initial freezing of this water.     

Solid State Characterization of Commercial Crystalline and Amorphous Atorvastatin Calcium Samples

Atorvastatin calcium (ATC), an anti-lipid BCS class II drug, is marketed in crystalline and amorphous solid forms. The objective of this study was to perform solid state characterization of commercial crystalline and amorphous ATC drug samples available in the Indian market. Six samples each of crystalline and amorphous ATC were characterized using X-ray powder diffractometry (XRPD), differential scanning calorimetry (DSC), thermogravimetric analysis, Karl Fisher titrimetry, microscopy (hot stage microscopy, scanning electron microscopy), contact angle, and intrinsic dissolution rate (IDR). All crystalline ATC samples were found to be stable form I, however one sample possessed polymorphic impurity, evidenced in XRPD and DSC analysis. Amongst the amorphous ATC samples, XRPD demonstrated five samples to be amorphous ‘form 27’, while, one matched amorphous ‘form 23’. Thermal behavior of amorphous ATC samples was compared to amorphous ATC generated by melt quenching in DSC. ATC was found to be an excellent glass former with T_g/T_m of 0.95. Residual crystallinity was detected in two of the amorphous samples by complementary use of conventional and modulated DSC techniques. The wettability and IDR of all amorphous samples was found to be higher than the crystalline samples. In conclusion, commercial ATC samples exhibited diverse solid state behavior that can impact the performance and stability of the dosage forms.