Testing the Efficiency of Biofilms Formed on Natural Substratum,Coyonoxtle (Opuntia Imbricata), for the Anaerobic Degradation of Aromatic Compounds

In this study, previously developed anaerobic microbial consortia capable of degrading aromatic compounds were used to develop biofilms on a natural material, coyonoxtle (Opuntia imbricata), which is abundantly available in North Mexico. The developed biofilms were evaluated for their efficiency in the biodegradation of different aromatic compounds, viz., phenol, catechol, 4‐aminobenzoic acid and p‐phenylenediamine in batch reactors. It was observed that in reactors with biofilms a more than 90 % COD removal and a concomitant production of methane could be obtained. But the rate of COD removal and methane production varied depending upon the type of biofilm used. Rumen‐derived biofilms demonstrated a lag phase of 7 to 14 days, whereas sludge‐derived biofilms exhibited a lag phase of more than three weeks. Between the biofilms from two sources, rumen‐derived biofilms showed a higher COD removal and methane production than sludge‐derived biofilms. When biofilm reactors were compared with reactors containing freely suspended consortia, it was evident that both rumen– and sludge‐derived biofilm reactors exhibited a two‐fold higher COD removal and methane production. Based on the results obtained, it can be concluded that coyonoxtle has the potential for use as a substratum.     

Nitric oxide‐mediated dispersal in single‐ and multi‐species biofilms of clinically and industrially relevant microorganisms

Strategies to induce biofilm dispersal are of interest due to their potential to prevent biofilm formation and biofilm‐related infections. Nitric oxide (NO), an important messenger molecule in biological systems, was previously identified as a signal for dispersal in biofilms of the model organism Pseudomonas aeruginosa. In the present study, the use of NO as an anti‐biofilm agent more broadly was assessed. Various NO donors, at concentrations estimated to generate NO levels in the picomolar and low nanomolar range, were tested on single‐species biofilms of relevant microorganisms and on multi‐species biofilms from water distribution and treatment systems. Nitric oxide‐induced dispersal was observed in all biofilms assessed, and the average reduction of total biofilm surface was 63%. Moreover, biofilms exposed to low doses of NO were more susceptible to antimicrobial treatments than untreated biofilms. For example, the efficacy of conventional chlorine treatments at removing multi‐species biofilms from water systems was increased by 20‐fold in biofilms treated with NO compared with untreated biofilms. These data suggest that combined treatments with NO may allow for novel and improved strategies to control biofilms and have widespread applications in many environmental, industrial and clinical settings.     

Multi-Channel Microfluidic Biosensor Platform Applied for Online Monitoring and Screening of Biofilm Formation and Activity

Bacterial colonization of surfaces and interfaces has a major impact on various areas including biotechnology, medicine, food industries, and water technologies. In most of these areas biofilm development has a strong impact on hygiene situations, product quality, and process efficacies. In consequence, biofilm manipulation and prevention is a fundamental issue to avoid adverse impacts. For such scenario online, non-destructive biofilm monitoring systems become important in many technical and industrial applications. This study reports such a system in form of a microfluidic sensor platform based on the combination of electrical impedance spectroscopy and amperometric current measurement, which allows sensitive online measurement of biofilm formation and activity. A total number of 12 parallel fluidic channels enable real-time online screening of various biofilms formed by different Pseudomonas aeruginosa and Stenotrophomonas maltophilia strains and complex mixed population biofilms. Experiments using disinfectant and antibiofilm reagents demonstrate that the biofilm sensor is able to discriminate between inactivation/killing of bacteria and destabilization of biofilm structures. The impedance and amperometric sensor data demonstrated the high dynamics of biofilms as a consequence of distinct responses to chemical treatment strategies. Gene expression of flagellar and fimbrial genes of biofilms grown inside the microfluidic system supported the detected biofilm growth kinetics. Thus, the presented biosensor platform is a qualified tool for assessing biofilm formation in specific environments and for evaluating the effectiveness of antibiofilm treatment strategies.     

Viscoelastic properties of Staphylococcus aureus and Staphylococcus epidermidis mono‐microbial biofilms

The viscoelastic properties of mono‐microbial biofilms produced by ocular and reference staphylococcal strains were investigated. The microorganisms were characterized for their haemolytic activity and agr typing and the biofilms, grown on stainless steel surface under static conditions, were analysed by Confocal Laser Scanning Microscopy. Static and dynamic rheometric tests were carried out to determine the steady‐flow viscosity and the elastic and viscous moduli. The analysed biofilms showed the typical time‐dependent behaviour of viscoelastic materials with considerable elasticity and mechanical stability except for Staphylococcus aureus ATCC 29213 biofilm which showed a very fragile structure. In particular, S. aureus 6ME biofilm was more compact than other staphylococcal biofilms studied with a yield stress ranging between 2 and 3 Pa. The data obtained in this work could represent a starting point for developing new therapeutic strategies against biofilm‐associated infections, such as improving the drug effect by associating an antimicrobial agent with a biofilm viscoelasticity modifier.     

Extracellular DNA in Helicobacter pylori biofilm: a backstairs rumour

Aims: This study detected and characterized the extracellular DNA (eDNA) in the biofilm extracellular polymeric substance (EPS) matrix of Helicobacter pylori and investigated the role of such component in the biofilm development. Methods and Results: Extracellular DNA was purified and characterized in a 2‐day‐old mature biofilm developed by the reference strain H. pylori ATCC 43629, the clinical isolate H. pylori SDB60 and the environmental strain H. pylori MDC1. Subsequently, the role of eDNA in the H. pylori biofilm was evaluated by adding DNase I during biofilm formation and on mature biofilms. Extracellular DNA was detected in the 2‐day‐old EPS biofilm matrix of all analysed H. pylori strains. The DNA fingerprintings, performed by RAPD analysis, on eDNA and intracellular DNA (iDNA), showed some remarkable differences. The data obtained by microtitre biofilm assay as well as colony forming unit count and CLSM (confocal laser scanning microscopy) qualitative analysis did not show any significant differences between the DNase I‐treated biofilms and the corresponding not treated controls both in formation and on mature biofilms. Conclusions: In this study, we provide evidence that eDNA is a component of the EPS matrix of H. pylori biofilm. The different profiles of eDNA and iDNA indicate that lysed cells are not the primary source of eDNA release, suggesting that other active mechanisms might be involved in this process. Moreover, the biomass assay suggests that eDNA may not be the main component of biofilm matrix, suggesting that it could be primarily involved in other mechanisms such as recombination processes, via transformation, contributing to the wide genomic variability of this micro‐organism defined as a ‘quasi‐species’. Significance and Impact of the Study: The presence of eDNA in H. pylori biofilm can contribute to the active dynamic exchange of information aimed to reach the best condition for the bacterial survival in the host and in the environment.     

Effect of fire on benthic algal assemblage structure and recolonization in intermittent streams

Abstract: Dry biofilm on rocks and other substrata forms an important drought refuge for benthic algae in intermittent streams following the cessation of flow. This dry biofilm is potentially susceptible to disturbance from bushfires, including direct burning and/or scorching and damage from radiant heat, particularly when streams are dry. Therefore, damage to dry biofilms by fire has the potential to influence algal recolonization and assemblage structure in intermittent streams following commencement of flow. The influence of fire on benthic algal assemblages and recolonization was examined in intermittent streams of the Grampians National Park, Victoria, Australia, using a field survey and manipulative field experiment. The field survey compared assemblages in two intermittent streams within a recently burnt area (within 5 months of the fire) with two intermittent streams within an unburnt area. The two burnt streams were still flowing during the fire so most biofilms were not likely to be directly exposed to flames. Considerable site‐to‐site and stream‐to‐stream variation was detected during the field survey, which may have obscured potential differences attributable to indirect effects of the fire. The manipulative field experiment occurred in two intermittent streams and consisted of five treatments chosen to replicate various characteristics of bushfires that may influence dry biofilms: dry biofilm exposed directly to fire; dry biofilm exposed to radiant heat; dry biofilm exposed to ash; and two procedural controls. After exposure to the different treatments, rocks were replaced in the streams and algae were sampled 7 days after flow commenced. Differences occurred across treatments, but treatment differences were inconsistent across the two streams. For example, direct exposure to fire reduced the abundance of recolonizing algae and altered assemblage structure in both streams, while radiant heat had an effect on assemblage structure in one stream only. The manipulative field experiment is likely to have represented the intensity of a small bushfire only. Nonetheless, significant differences across treatments were detected, so these experimental results suggest that fire can damage dry biofilms, and hence, influence algal recolonization and assemblage structure in intermittent streams.     

pH, redox potential and local biofilm potential microenvironments within Geobacter sulfurreducens biofilms and their roles in electron transfer

The limitation of pH inside electrode‐respiring biofilms is a well‐known concept. However, little is known about how pH and redox potential are affected by increasing current inside biofilms respiring on electrodes. Quantifying the variations in pH and redox potential with increasing current is needed to determine how electron transfer is tied to proton transfer within the biofilm. In this research, we quantified pH and redox potential variations in electrode‐respiring Geobacter sulfurreducens biofilms as a function of respiration rates, measured as current. We also characterized pH and redox potential at the counter electrode. We concluded that (1) pH continued to decrease in the biofilm through different growth phases, showing that the pH is not always a limiting factor in a biofilm and (2) decreasing pH and increasing redox potential at the biofilm electrode were associated only with the biofilm, demonstrating that G. sulfurreducens biofilms respire in a unique internal environment. Redox potential inside the biofilm was also compared to the local biofilm potential measured by a graphite microelectrode, where the tip of the microelectrode was allowed to acclimatize inside the biofilm. Biotechnol. Bioeng. 2012; 109: 2651–2662. © 2012 Wiley Periodicals, Inc.     

Design and field application of a UV-LED based optical fiber biofilm sensor

Detecting changes in the formation dynamics of biofilms stemming from bacteria and unicellular microorganisms in their natural environment is of prime interest for biological, ecological as well as anti-fouling technology research. We developed a robust optical fiber-based biofilm sensor ready to be applied in natural aquatic environments for on-line, in situ and non-destructive monitoring of large-area biofilms. The device is based on the detection of the natural fluorescence of microorganisms constituting the biofilm. Basically, the intrinsic fluorescence of the amino acid tryptophan is excited at a wavelength of λ=280 nm and detected at λ=350 nm utilising a numerically optimized sensor head equipped with a UV-LED light source and optical fiber bundles for efficient fluorescence light collection. Calibration was carried out with tryptophan solutions and two characteristic marine bacteria strains revealing linear signal response, satisfactory background suppression, wide dynamic range, and an experimental detection limit of 4 × 10(3)cells/cm(2). Successful field experiments in the Baltic Sea accomplished over a period of twenty-one days provided for the first time continuous observation of biofilm formation dynamics in a natural habitat. Starting from the first adhering bacteria, the measurement yielded the characteristic three phases of biofilm formation up to a fully developed biofilm. The sensor system holds potential for applications in aquatic sciences including deep sea research and, after further miniaturisation, in the industrial and biomedical field.     

An in vitro urinary tract catheter system to investigate biofilm development in catheter-associated urinary tract infections

Biofilm development in urinary tract catheters is an often underestimated problem. However, this form of infection leads to high mortality rates and causes significant costs in health care. Therefore, it is important to analyze these biofilms and establish avoiding strategies. In this study a continuous flow-through system for the cultivation of biofilms under catheter-associated urinary tract infection conditions was established and validated. The in vitro urinary tract catheter system implies the composition of urine (artificial urine medium), the mean volume of urine of adults (1 mL min^-1), the frequently used silicone catheter (foley silicon catheter) as well as the infection with uropathogenic microorganisms like Pseudomonas aeruginosa. Three clinical isolates from urine of catheterized patients were chosen due to their ability to form biofilms, their mobility and their cell surface hydrophobicity. As reference strain P. aeruginosa PA14 has been used. Characteristic parameters as biofilm thickness, specific biofilm growth rate and substrate consumption were observed. Biofilm thicknesses varied from 105 ± 16 μm up to 246 ± 67 μm for the different isolates. The specific biofilm growth rate could be determined with a non invasive optical biomass sensor. This sensor allows online monitoring of the biofilm growth in the progress of the cultivation.     

A novel in vitro flat‐bed perfusion biofilm model for determining the potential antimicrobial efficacy of topical wound treatments

Aims: To develop an in vitro flat‐bed perfusion biofilm model that could be used to determine the antimicrobial efficacy of topically applied treatments. Methods and Results: Pseudomonas aeruginosa and Staphylococcus aureus biofilms were grown within continuously perfused cellulose matrices. Enumeration of the biofilm density and eluate was performed at various sampling times, enabling determination of the biofilm growth rate. Two antimicrobial wound dressings were applied to the surface of mature biofilms and periodically sampled. To enable real‐time imaging of biofilm growth and potential antimicrobial kinetics, a bioluminescent Ps. aeruginosa biofilm was monitored using low‐light photometry. Target species produced reproducible steady‐state biofilms at a density of c. 10⁷ per biofilm support matrix, after 24‐h perfusion. Test dressings elicited significant antimicrobial effects, producing differing kill kinetic profiles. There was a good correlation between photon and viable count data. Conclusions: The model enables determination of the antimicrobial profile of topically applied treatments against target species biofilms, accurately differentiating bactericidal from bacteriostatic effects. Moreover, these effects could be monitored in real time using bioluminescence. Significance and Impact of the Study: This is the first in vitro biofilm model which can assess the antimicrobial potential of topical therapies in a dynamic growth environment.     

Biofilm formation in Streptococcus pneumoniae

Biofilm‐grown bacteria are refractory to antimicrobial agents and show an increased capacity to evade the host immune system. In recent years, studies have begun on biofilm formation by Streptococcus pneumoniae, an important human pathogen, using a variety of in vitro model systems. The bacterial cells in these biofilms are held together by an extracellular matrix composed of DNA, proteins and, possibly, polysaccharide(s). Although neither the precise nature of these proteins nor the composition of the putative polysaccharide(s) is clear, it is known that choline‐binding proteins are required for successful biofilm formation. Further, many genes appear to be involved, although the role of each appears to vary when biofilms are produced in batch or continuous culture. Prophylactic and therapeutic measures need to be developed to fight S. pneumoniae biofilm formation. However, much care needs to be taken when choosing strains for such studies because different S. pneumoniae isolates can show remarkable genomic differences. Multispecies and in vivo biofilm models must also be developed to provide a more complete understanding of biofilm formation and maintenance.     

Biofilm shows spatially stratified metabolic responses to contaminant exposure

Biofilms are core to a range of biological processes, including the bioremediation of environmental contaminants. Within a biofilm population, cells with diverse genotypes and phenotypes coexist, suggesting that distinct metabolic pathways may be expressed based on the local environmental conditions in a biofilm. However, metabolic responses to local environmental conditions in a metabolically active biofilm interacting with environmental contaminants have never been quantitatively elucidated. In this study, we monitored the spatiotemporal metabolic responses of metabolically active Shewanella oneidensis MR‐1 biofilms to U(VI) (uranyl, UO₂ ²⁺) and Cr(VI) (chromate, CrO₄ ^2?) using non‐invasive nuclear magnetic resonance imaging (MRI) and spectroscopy (MRS) approaches to obtain insights into adaptation in biofilms during biofilm‐contaminant interactions. While overall biomass distribution was not significantly altered upon exposure to U(VI) or Cr(VI), MRI and spatial mapping of the diffusion revealed localized changes in the water diffusion coefficients in the biofilms, suggesting significant contaminant‐induced changes in structural or hydrodynamic properties during bioremediation. Finally, we quantitatively demonstrated that the metabolic responses of biofilms to contaminant exposure are spatially stratified, implying that adaptation in biofilms is custom‐developed based on local microenvironments.     

Diffusion profiles in L. lactis biofilms under different conditions

Despite being an important topic in biofilm research, we still know little about diffusion in biofilms. Emerging biofilms of Lactococcus lactis growing in custom‐made flow‐cells were monitored and diffusion constants across the height of the biofilms recorded. The biofilms showed different diffusional behavior with regard to flow rate and pH variations, despite growing to similar thickness. At a higher flow rate, the biofilm exhibits slower diffusion compared to the reference cultivation at lower flow rate. By increasing pH, the biofilm exhibited fast growth and little difference in diffusion compared to the reference cultivation. Furthermore, the diffusion inside of the biofilms differed depending on the position in the flow‐cell. The present study reveals new insights in how external factors can affect structure and density of biofilms. The method can be reliably used for L. lactis biofilms with a thickness up to 120 μm.     

An in vitro urinary tract catheter system to investigate biofilm development in catheter-associated urinary tract infections

Biofilm development in urinary tract catheters is an often underestimated problem. However, this form of infection leads to high mortality rates and causes significant costs in health care. Therefore, it is important to analyze these biofilms and establish avoiding strategies. In this study a continuous flow-through system for the cultivation of biofilms under catheter-associated urinary tract infection conditions was established and validated. The in vitro urinary tract catheter system implies the composition of urine (artificial urine medium), the mean volume of urine of adults (1 mL min^–1), the frequently used silicone catheter (foley silicon catheter) as well as the infection with uropathogenic microorganisms like Pseudomonas aeruginosa. Three clinical isolates from urine of catheterized patients were chosen due to their ability to form biofilms, their mobility and their cell surface hydrophobicity. As reference strain P. aeruginosa PA14 has been used. Characteristic parameters as biofilm thickness, specific biofilm growth rate and substrate consumption were observed. Biofilm thicknesses varied from 105 ± 16 μm up to 246 ± 67 μm for the different isolates. The specific biofilm growth rate could be determined with a non invasive optical biomass sensor. This sensor allows online monitoring of the biofilm growth in the progress of the cultivation.     

Influence of Hydrodynamics and Cell Signaling on the Structure and Behavior of Pseudomonas aeruginosa Biofilms

Biofilms were grown from wild-type (WT) Pseudomonas aeruginosa PAO1 and the cell signaling lasI mutant PAO1-JP1 under laminar and turbulent flows to investigate the relative contributions of hydrodynamics and cell signaling for biofilm formation. Various biofilm morphological parameters were quantified using Image Structure Analyzer software. Multivariate analysis demonstrated that both cell signaling and hydrodynamics significantly (P < 0.000) influenced biofilm structure. In turbulent flow, both biofilms formed streamlined patches, which in some cases developed ripple-like wave structures which flowed downstream along the surface of the flow cell. In laminar flow, both biofilms formed monolayers interspersed with small circular microcolonies. Ripple-like structures also formed in four out of six WT biofilms, although their velocity was approximately 10 times less than that of those that formed in the turbulent flow cells. The movement of biofilm cell clusters over solid surfaces may have important clinical implications for the dissemination of biofilm subject to fluid shear, such as that found in catheters. The ability of the cell signaling mutant to form biofilms in high shear flow demonstrates that signaling mechanisms are not required for the formation of strongly adhered biofilms. Similarity between biofilm morphologies in WT and mutant biofilms suggests that the dilution of signal molecules by mass transfer effects in faster flowing systems mollifies the dramatic influence of signal molecules on biofilm structure reported in previous studies.     

Simulation of growth and detachment in biofilm systems under defined hydrodynamic conditions

Detachment from biofilms was evaluated using a mixed culture biofilm grown on primary wastewater in a tube reactor. The growth of biofilms and the detachment of biomass from biofilms are strongly influenced by hydrodynamic conditions. In a long-term study, three biofilms were cultivated in a biofilm tube reactor. The conducted experiments of biofilm growth and detachment can be divided into three phases: 1) an exponential phase with a rapid increase of the biofilm thickness, 2) a quasi-steady-state with spontaneous fluctuation of the biofilm thickness between 500 and 1,200 microm in the investigated biofilm systems, and 3) a washout experiment with increased shear stress in three to four steps after several weeks of quasi-steady-state. Whereas the biofilm thickness during the homogeneous growth phase can be regarded constant throughout the reactor, it was found to be very heterogeneous during the quasi-steady-state and the washout experiments. Growth and detachment during all three phases was simulated with the same one-dimensional biofilm model. For each of the three phases, a different detachment rate model was used. During the homogeneous growth phase, detachment was modeled proportional to the biofilm growth rate. During the quasi-steady-state phase, detachment was described by random detachment events assuming a base biofilm thickness. Finally, the washout experiment was simulated with detachment being a function of the biofilm thickness before the increase of the shear stress.     

Predicting biofilm deformation with a viscoelastic phase-field model: Modeling and experimental studies

Biofilms commonly develop in flowing aqueous environments, where the flow causes the biofilm to deform. Because biofilm deformation affects the flow regime, and because biofilms behave as complex heterogeneous viscoelastic materials, few models are able to predict biofilm deformation. In this study, a phase-field (PF) continuum model coupled with the Oldroyd-B constitutive equation was developed and used to simulate biofilm deformation. The accuracy of the model was evaluated using two types of biofilms: a synthetic biofilm, made from alginate mixed with bacterial cells, and a Pseudomonas aeruginosa biofilm. Shear rheometry was used to experimentally determine the mechanical parameters for each biofilm, used as inputs for the model. Biofilm deformation under fluid flow was monitored experimentally using optical coherence tomography. The comparison between the experimental and modeling geometries, for selected horizontal cross sections, after fluid-driven deformation was good. The relative errors ranged from 3.2 to 21.1% for the synthetic biofilm and from 9.1 to 11.1% for the P. aeruginosa biofilm. This is the first demonstration of the effectiveness of a viscoelastic PF biofilm model. This model provides an important tool for predicting biofilm viscoelastic deformation. It also can benefit the design and control of biofilms in engineering systems.