Application of dimeric orthopalladated complex in Suzuki-Miyaura cross coupling reaction under microwave irradiation and conventional heating

The Suzuki-Miyaura reaction of various aryl halides using [Pd{C₆H₂(CH₂CH₂NH₂)-(OMe)₂,3,4} (μ-Br)]₂ have been investigated. This orthopalladated complex is an efficient, stable and non-sensitive to air and moisture catalyst for the hetrocoupling reaction in DMF as the reaction solvent at 130 °C. The combination of dimeric complex as homogenous catalyst and microwave irradiation can be very useful and efficient methods in organic synthesis, so the application of microwave irradiation have been investigated using homogenous dimeric complex [Pd{C₆H₂(CH₂CH₂NH₂)-(OMe)₂,3,4} (μ-Br)]₂. Application of dimeric complex as catalyst caused to produce the desired coupling products and the using of microwave irradiation improving the yields of the reactions and shortening the reaction times.     

Rational Design of Core@shell Structured CoSx@Cu2MoS4 Hybridized MoS2/N,S‐Codoped Graphene as Advanced Electrocatalyst for Water Splitting and Zn‐Air Battery

A novel hybrid of small core@shell structured CoS_x@Cu₂MoS₄ uniformly hybridizing with a molybdenum dichalcogenide/N,S‐codoped graphene hetero‐network (CoS_x@Cu₂MoS₄‐MoS₂/NSG) is prepared by a facile route. It shows excellent performance toward the oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER) in alkaline medium. The hybrid exhibits rapid kinetics for ORR with high electron transfer number of ≈3.97 and exciting durability superior to commercial Pt/C. It also demonstrates great potential with remarkable stability for HER and OER, requiring low overpotential of 118.1 and 351.4 mV, respectively, to reach a current density of 10 mA cm^?2. An electrolyzer based on CoS_x@Cu₂MoS₄‐MoS₂/NSG produces low cell voltage of 1.60 V and long‐term stability, surpassing a device of Pt/C + RuO₂/C. In addition, a Zn‐air battery using cathodic CoS_x@Cu₂MoS₄‐MoS₂/NSG catalyst delivers a high cell voltage of ≈1.44 V and a power density of 40 mW cm^?2 at 58 mA cm^?2, better than the state‐of‐the‐art Pt/C catalyst. These achievements are due to the rational combination of highly active core@shell CoS_x@Cu₂MoS₄ with large‐area and high‐porosity MoS₂/NSG to produce unique physicochemical properties with multi‐integrated active centers and synergistic effects. The outperformances of such catalyst suggest an advanced candidate for multielectrocatalysis applications in metal‐air batteries and hydrogen production.     

Tailoring Interfacial Charge Transfer of Epitaxially Grown Ir Clusters for Boosting Hydrogen Oxidation Reaction

The sluggish kinetics of hydrogen oxidation reaction (HOR) is one of the critical challenges for anion exchange membrane fuel cells. Here, we report epitaxial growth of Ir nanoclusters (<2 nm) on a MoS₂ surface (Ir/MoS₂) and optimize the alkaline HOR activity via tailoring interfacial charge transfer between Ir clusters and MoS₂. The electron transfer from MoS₂ to Ir clusters can effectively prevent the oxidation of Ir clusters, which is not the case for carbon-supported Ir nanoclusters (Ir/C) synthesized using the same method. Moreover, the HOR performance of the Ir/MoS₂ can be further optimized by tuning the hydrogen binding energy (HBE) via a precise annealing treatment. A substantial exchange current density of 1.28 mA cm_ECSA⁻² is achieved in the alkaline medium, which is ∼10 times over that of Ir/C. The HOR mass-specific activity of Ir/MoS₂ heterostructure is as high as 182 mA mg_Ir⁻¹. The experimental results and density functional theory calculations reveal that the significant improved HOR activity is attributed to the decreased HBE, which highlights epitaxial growth is an effective way for boosting catalytic activity of heterostructured catalysts.     

H2‐Directing Strategy on In Situ Synthesis of Co‐MoS2 with Highly Expanded Interlayer for Elegant HER Activity and its Mechanism

MoS₂ has drawn great attention as a promising Pt‐substituting catalyst for the hydrogen evolution reaction (HER). This work utilizes H₂ as the structure directing agent (SDA) to in situ synthesize a range of Co‐MoS₂‐n (n = 0, 0.5, 1.0, 1.4, 2.0) with expanded interlayer spacings (d = 9.2 – 11.1 Å), which significantly boost their HER activities. The Co‐MoS₂‐1.4 with an interlayer spacing of 10.3 Å presents an extremely low overpotential of 56 mV (at 10 mA cm^?2) and a Tafel slope of 32 mV dec^?1, which is superior than most reported MoS₂‐based catalysts. Density function theory calculations are used to gain insights that i) the H₂ can be dissociatively adsorbed on MoS₂ and greatly affect the related surface free energy by regulating the interlayer spacing; ii) the expanded interlayer spacing can significantly decrease the absolute value of ΔG_H, thereby leading to greatly promoted HER activity. Additionally, the large amounts of 1T phase (73.9–79.2%) and Co‐Mo‐S active sites (40.9–91.3%) also contribute to the enhanced HER activity of the synthesized samples. Overall, a simple new strategy for in situ synthesis of Co‐MoS₂ with an expanded interlayer spacing is proposed, which sheds light on other 2D energy material designs.     

Dual‐Functional N Dopants in Edges and Basal Plane of MoS2 Nanosheets Toward Efficient and Durable Hydrogen Evolution

Herein, the authors explicitly reveal the dual‐functions of N dopants in molybdenum disulfide (MoS₂) catalyst through a combined experimental and first‐principles approach. The authors achieve an economical, ecofriendly, and most efficient MoS₂‐based hydrogen evolution reaction (HER) catalyst of N‐doped MoS₂ nanosheets, exhibiting an onset overpotential of 35 mV, an overpotential of 121 mV at 100 mA cm^?2 and a Tafel slope of 41 mV dec^?1. The dual‐functions of N dopants are (1) activating the HER catalytic activity of MoS₂ S‐edge and (2) enhancing the conductivity of MoS₂ basal plane to promote rapid charge transfer. Comprehensive electrochemical measurements prove that both the amount of active HER sites and the conductivity of N‐doped MoS₂ increase as a result of doping N. Systematic first‐principles calculations identify the active HER sites in N‐doped MoS₂ edges and also illustrate the conducting charges spreading over N‐doped basal plane induced by strong Mo 3d –S 2p –N 2p hybridizations at Fermi level. The experimental and theoretical research on the efficient HER catalysis of N‐doped MoS₂ nanosheets possesses great potential for future sustainable hydrogen production via water electrolysis and will stimulate further development on nonmetal‐doped MoS₂ systems to bring about novel high‐performance HER catalysts.     

Facile synthesis of glycosylated Fmoc amino acid building blocks assisted by microwave irradiation

The synthesis of glycosylated Fmoc amino acids by reaction of mono- and disaccharide peracetates with Fmoc amino acids having free carboxyl groups was rapidly promoted by Lewis acids (SnCl₄, BF₃·Et₂O) under microwave irradiation. The products are useful building blocks for the synthesis of glycopeptides.     

Rewetting of Cutaway Peatlands: Are We Re‐Creating Hot Spots of Methane Emissions?

Hot spots of CH₄ emissions are a typical feature of pristine peatlands at the microsite and landscape scale. To determine whether rewetting and lake construction in a cutaway peatland would result in the re‐creation of hot spots, we first measured CH₄ fluxes over a 2‐year period with static chambers and estimated annual emissions. Second, to assess whether rewetting and lake creation would produce hot spots at the landscape level, we hypothesized a number of alternative land use scenarios for the peatland following the cessation of peat extraction. Using the results from this study and other studies from literature, we calculated the global warming potential (GWP) of each scenario and the respective contribution of CH₄. The results showed that hot spots of CH₄ fluxes were observed as a consequence of microsite‐specific differences in water table (WT) position and plant productivity. CH₄ fluxes were closely related to peat temperature at 10 cm depth and WT position. Annual emissions ranged from 4.3 to 38.8 g CH₄ m^?2 yr^?1 in 2002 and 3.2 to 28.8 g CH₄ m^?2 yr^?1 in 2003. The scenario results suggest that lake creation is likely to result in the re‐creation of a hot spot at the landscape level. However, the transition from cutaway to wetland ecosystem may lead to a reduction in the GWP of the peatland.     

A Facile Strategy to Construct Amorphous Spinel‐Based Electrocatalysts with Massive Oxygen Vacancies Using Ionic Liquid Dopant

Oxygen vacancies are demonstrated to be beneficial to various electrocatalytic reactions. However, integrating oxygen vacancies into an amorphous catalyst with a large specific surface area, and investigating its effect on the oxygen evolution reaction remains a great challenge. Herein, oxygen vacancies are introduced into an amorphous N, P, and F tri‐doped CoFe₂O₄ using ionic liquid as a dopant. Simultaneously, ultrafine MoS₂ nanoclusters are anchored onto its surface to increase the specific surface area. The vacancy‐rich MoS₂/NPF‐CoFe₂O₄ exhibits an overpotential of 250 mV and a small Tafel slope of 41 mV dec^?1, which is the best spinel‐based oxygen evolution reaction (OER) electrocatalysts so far. The excellent performance is attributed to massive oxygen vacancies, amorphous structure, large surface area, and synergistic coupling effects among active species. Density‐functional theory calculations reveal that the electronic structure of the catalyst can be modulated in the presence of heteroatoms and MoS₂ nanoclusters, and then the energy barriers of intermediates are decreased as well, which enhances the OER performance. This design not only provides a simple strategy to construct amorphous structures with abundant oxygen vacancies using ionic liquid‐dopants, but also presents an in‐depth insight into the OER mechanism in alkaline solution.     

Chemical Consequences of Alkali Inhomogeneity in Cu2ZnSnS4 Thin‐Film Solar Cells

This study offers new insight into the role of Na in Cu₂ZnSnS₄ (CZTS) thin film solar cells by studying samples with a spatially varying alkali distribution. This is achieved by omitting a diffusion barrier between the soda‐lime glass substrate and the Mo back contact, where compositional variations of the glass inherently result in non‐uniform alkali distributions in the CZTS. By correlating light beam induced current (LBIC) maps with secondary ion mass spectrometry composition maps, it is shown that samples containing regions of higher Na concentration (“hot spots”) have corresponding LBIC hot spots on comparable length scales. Samples containing an alkali diffusion barrier have lower LBIC dispersion; thus, LBIC can be used to evaluate non‐uniformity in CZTS devices, where a common cause is Na inhomogeneity. Moreover, it is shown that the Na hot spots are strongly correlated with other compositional variations in the device, including increased Cu in‐diffusion with the underlying MoS₂ layer and decreased diffusion of Cd to the back contact. Neither of these effects are well understood in CZTS devices, and neither have previously been correlated with the presence or absence of Na.     

Solar‐Light‐Driven CO2 Reduction by CH4 on Silica‐Cluster‐Modified Ni Nanocrystals with a High Solar‐to‐Fuel Efficiency and Excellent Durability

Catalytic CO₂ reforming of CH₄ (CRM) to produce syngas (H₂ and CO) provides a promising approach to reducing global CO₂ emissions and the extensive utilization of natural gas resources. However, the rapid deactivation of the reported catalysts due to severe carbon deposition at high reaction temperatures and the large energy consumption of the process hinder its industrial application. Here, a method for almost completely preventing carbon deposition is reported by modifying the surface of Ni nanocrystals with silica clusters. The obtained catalyst exhibits excellent durability for CRM with almost no carbon deposition and deactivation after reaction for 700 h. Very importantly, it is found that CRM on the catalyst can be driven by focused solar light, thus providing a promising new approach to the conversion of renewable solar energy to fuel due to the highly endothermic characteristics of CRM. The reaction yields high production rates of H₂ and CO (17.1 and 19.9 mmol min^?1 g^?1, respectively) with a very high solar‐to‐fuel efficiency (η, 12.5%). Even under focused IR irradiation with a wavelength above 830 nm, the η of the catalyst remains as high as 3.1%. The highly efficient catalytic activity arises from the efficient solar‐light‐driven thermocatalytic CRM enhanced by a novel photoactivation effect.     

Direct conversion of cellulose to 1-(furan-2-yl)-2-hydroxyethanone in zinc chloride solution under microwave irradiation

Conversion of cellulose to 1-(furan-2-yl)-2-hydroxyethanone has been demonstrated in concentrated zinc chloride solution under microwave irradiation. Compared with the conventional oil-bath heating mode, microwave irradiation significantly reduced the reaction time and increased the yield of 1-(furan-2-yl)-2-hydroxyethanone. A typical degradation reaction with cellulose produced 1-(furan-2-yl)-2-hydroxyethanone in 12.0% molar yield in ZnCl₂ solution (ZnCl₂–H₂O ratio = 2.25:1, w/w) with microwave irradiation at 600 W for 5 minutes at 135 °C.     

Highly Efficient Solar‐Driven Carbon Dioxide Reduction on Molybdenum Disulfide Catalyst Using Choline Chloride‐Based Electrolyte

Conversion of CO₂ to energy‐rich chemicals using renewable energy is of much interest to close the anthropogenic carbon cycle. However, the current photoelectrochemical systems are still far from being practically feasible. Here the successful demonstration of a continuous, energy efficient, and scalable solar‐driven CO₂ reduction process based on earth‐abundant molybdenum disulfide (MoS₂) catalyst, which works in synergy with an inexpensive hybrid electrolyte of choline chloride (a common food additive for livestock) and potassium hydroxide (KOH) is reported. The CO₂ saturated hybrid electrolyte utilized in this study also acts as a buffer solution (pH ≈ 7.6) to adjust pH during the reactions. This study reveals that this system can efficiently convert CO₂ to CO with solar‐to‐fuel and catalytic conversion efficiencies of 23% and 83%, respectively. Using density functional theory calculations, a new reaction mechanism in which the water molecules near the MoS₂ cathode act as proton donors to facilitate the CO₂ reduction process by MoS₂ catalyst is proposed. This demonstration of a continuous, cost‐effective, and energy efficient solar driven CO₂ conversion process is a key step toward the industrialization of this technology.     

Microwave‐Induced Metal Dissolution Synthesis of Core–Shell Copper Nanowires/ZnS for Visible Light Photocatalytic H2 Evolution

A microwave‐induced metal dissolution strategy is developed for in situ synthesis of copper nanowires/ZnS (CuNWs/ZnS) hybrids with core–shell structure. The CuNWs are used as microwave antennas to create local “super‐hot” surfaces to further initiate ZnS crystallization with full coverage on CuNWs. With the help of S^2?, the hot metal surface further results in the CuNWs dissolution with promoted Cu⁺ diffusion and incorporation into the ZnS lattice. With the narrowed bandgap of ZnS and the strongly coupled interface between CuNWs and ZnS created by microwaves, the as‐prepared hybrid composites exhibit an enhanced activity and stability in visible light for the photocatalytic H₂ evolution. The corresponding H₂ evolution rate reaches up to 10722 µmol h^?1 g^?1 with apparent quantum efficiency (AQE) of 69% under 420 nm LED irradiation, showing a remarkably high AQE among the noble‐metal free visible light‐driven photocatalysts and demonstrating a promising potential in practical applications to deal with the energy crisis.     

Supercapacitor Electrodes Obtained by Directly Bonding 2D MoS2 on Reduced Graphene Oxide

Layered molybdenum disulfide (MoS₂) is deposited by microwave heating on a reduced graphene oxide (RGO). Three concentrations of MoS₂ are loaded on RGO, and the structure and morphology are characterized. The first layers of MoS₂ are detected as being directly bonded with the oxygen of the RGO by covalent chemical bonds (Mo‐O‐C). Electrochemical characterizations indicate that this electroactive material can be cycled reversibly between 0.25 and 0.8 V in 1 m HClO₄ solution for hybrids with low concentrations of MoS₂ layers (LCMoS₂/RGO) and between 0.25 and 0.65 V for medium (MCMoS₂/RGO) and high concentrations (HCMoS₂/RGO) of MoS₂ layers on graphene. The specific capacitance measured values at 10 mV s^?1 are 128, 265, and 148 Fg^?1 for the MoS₂/RGO with low, medium, and high concentrations of MoS₂, respectively, and the calculated energy density is 63 W h kg^?1 for the LCMoS₂/RGO hybrid. This supercapacitor electrode also exhibits superior cyclic stability with 92% of the specific capacitance retained after 1000 cycles.     

Ultrastable In‐Plane 1T–2H MoS2 Heterostructures for Enhanced Hydrogen Evolution Reaction

Metallic 1T MoS₂ is highly desirable for catalyzing electrochemical hydrogen production from water owing to its high electrical conductivity. However, stable 1T MoS₂ is difficult to be produced in large‐scale by either common chemical or physical approaches. Here, ultrastable in‐plane 1T–2H MoS₂ heterostructures are achieved via a simple one‐pot annealing treatment of 2H MoS₂ bulk under a mixture gas of Ar and phosphorous vapor, where phosphorus cannot only occupy the interspace of MoS₂ bulk, resulting in the expansion of MoS_2, but also embed into the lattice of MoS_2, inducing the partial phase transition from 2H to 1T phases of MoS₂. Benefiting from its significantly improved electrical conductivity, highly exposed active sites, and hydrophily property, in‐plane 1T–2H MoS₂ heterostructures exhibit largely improved electrocatalytic properties for hydrogen evolution reaction (HER) in alkaline electrolytes.     

Catalysis of the acetylene hydrochlorination reaction by Si-doped Au clusters: a DFT study

The mechanisms for the acetylene hydrochlorination reaction on pristine Au₇ and Au₈ clusters and on the Si-doped Au clusters Au₆Si and Au₇Si were systematically investigated via density functional theory using the PBE functional. The band gap (?E_g) of the Au₇Si cluster was found to smaller than that of its undoped equivalent (Au₈), thus enhancing its catalytic activity, and Au₇Si presented a significantly reduced activation barrier (16.69 kcal mol^?1) for the acetylene hydrochlorination reaction compared with the pristine Au₈ cluster (21.83 kcal mol^?1). On the other hand, the activation barrier for the acetylene hydrochlorination reaction was not lower for the Au₆Si cluster than for the pristine Au₇ cluster because the band gap (?E_g) of Au₆Si was found to be larger than that of Au₇. Hence, the current work shows that the catalytic activities of gold clusters can be systematically modified by doping them. Our findings also suggest how to enhance the acetylene hydrochlorination reaction by doping foreign atoms into Au clusters.

Open image in new window

Graphical abstract The Si-doped Au₇Si cluster showed stronger catalytic activity for the acetylene hydrochlorination reaction compared with the pristine Au₈ cluster.

     

Process intensification of immobilized lipase catalysis by microwave irradiation in the synthesis of 4-chloro-2-methylphenoxyacetic acid (MCPA) esters

4-Chloro-2-methylphenoxyacetic acid (MCPA) is a selective systemic herbicide which is absorbed by leaves and roots. MCPA esters are preferred due to their low water solubility and environmental friendliness. Esterification of MCPA with n-butanol was investigated as a model reaction using immobilized enzymes under the influence of microwave irradiation. Different immobilized enzymes such as Novozym 435, Lipozyme TL IM, Lipozyme RM IM and Lipase AYS Amano were studied under microwave irradiation amongst which Novozym 435 (immobilized Candida antarctica lipase B) was the best catalyst. Effects of various parameters were systematically studied on rates and conversion. Under microwave irradiation, the initial rates were observed to increase up to 2-fold. Under optimized conditions of 0.1 mmol MCPA and 0.3 mmol n-butanol in 15 mL 1,4-dioxane as solvent, Novozym 435 showed a conversion of 83% at 60 °C in 6 h. Based on initial rate and progress curve data, the reaction was shown to follow the Ping Pong bi–bi mechanism with inhibition by MCPA and n-butanol. Esterification of MCPA was also studied with different alcohols such as isopropyl alcohol, n-pentanol, n-hexanol, benzyl alcohol and 2-ethyl-1-hexanol.     

Optimization of bio-diesel production from soybean and wastes of cooked oil: Combining dielectric microwave irradiation and a SrO catalyst

This work offers an optimized method in the transesterification of pristine (soybean) oil and cooked oil to bio-diesel, based on microwave dielectric irradiation as a driving force for the transesterification reaction and SrO as a catalyst. This combination has demonstrated excellent catalytic activity and stability. The transesterification was carried out with and without stirring. According to ¹H NMR spectroscopy and TLC results, this combination accelerates the reaction (to less than 60 s), maintaining a very high conversion (99%) and high efficiency. The catalytic activity of SrO under atmospheric pressure in the presence of air and under the argon atmosphere is demonstrated. The optimum conversion of cooked oil (99.8%) is achieved under MW irradiation of 1100 W output with magnetic stirring after only 10 s. The optimum method decreases the cost of bio-diesel production and has the potential for industrial application in the transesterification of cooked oil to bio-diesel.     

The Comparative Photodegradation Activities of Pentachlorophenol (PCP) and Polychlorinated Biphenyls (PCBs) Using UV Alone and TiO2-Derived Photocatalysts in Methanol Soil Washing Solution

Photochemical treatment is increasingly being applied to remedy environmental problems. TiO₂-derived catalysts are efficiently and widely used in photodegradation applications. The efficiency of various photochemical treatments, namely, the use of UV irradiation without catalyst or with TiO₂/graphene-TiO₂ photodegradation methods was determined by comparing the photodegadation of two main types of hydrophobic chlorinated aromatic pollutants, namely, pentachlorophenol (PCP) and polychlorinated biphenyls (PCBs). Results show that photodegradation in methanol solution under pure UV irradiation was more efficient than that with either one of the catalysts tested, contrary to previous results in which photodegradation rates were enhanced using TiO₂-derived catalysts. The effects of various factors, such as UV light illumination, addition of methanol to the solution, catalyst dosage, and the pH of the reaction mixture, were examined. The degradation pathway was deduced. The photochemical treatment in methanol soil washing solution did not benefit from the use of the catalysts tested. Pure UV irradiation was sufficient for the dechlorination and degradation of the PCP and PCBs.     

Atomic‐Scale Visualization of Electrochemical Lithiation Processes in Monolayer MoS2 by Cryogenic Electron Microscopy

While lithium ion batteries with electrodes based on intercalation compounds have dominated the portable energy storage market for decades, the energy density of these materials is fundamentally limited. Today, rapidly growing demand for this type of energy storage is driving research into materials that utilize alternative reaction mechanisms to enable higher energy densities. Transition metal compounds are one such class of materials, with storage enabled by “conversion” reactions, where the material is converted to new compound upon lithiation. MoS₂ is one example of this type of material that has generated a large amount of interest recently due to its high theoretical lithium storage capacity compared to graphite. Here, cryogenic scanning transmission electron microscopy techniques are used to reveal the atomic‐scale processes that occur during reaction of a model monolayer MoS₂ system by enabling the unaltered atomic structure to be determined at various levels of lithiation. It is revealed that monolayer MoS₂ can undergo a conversion reaction even with no substrate, and that the resulting particles are smaller than those that form in bulk MoS₂, likely due to the more limited 2D diffusion. Additionally, while bilayer MoS₂ undergoes intercalation with a corresponding phase transition before conversion, monolayer MoS₂ does not.