Effects of airflow and liquid temperature on ammonia mass transfer above an emission surface: Experimental study on emission rate

The present study performed a series of experiments in a wind tunnel to investigate the impact of velocity, turbulence intensity and liquid–air temperature difference on ammonia emission rates. Decreasing velocity, turbulence intensity and liquid temperature are shown to reduce the ammonia emission rates. The emission rates are more sensitive to the change of velocity at a low velocity compared to change of velocity at a higher velocity range, which corresponds with the conclusion that the boundary layer thickness of velocity increases sharply when velocity is changed from 0.2 m/s to 0.1 m/s. In addition, the emission rates are more sensitive to the change of temperature at a higher temperature than at a lower liquid temperature range. The influence of velocity and liquid–air temperature difference on boundary layer thickness is also analyzed. The relationship between the emission rate and boundary layer thickness is presented.     

Analysis of deformation behaviour of Al–Ni–Co thin film coated aluminium during nano-indentation: a molecular dynamics study

In the present work, molecular dynamics simulations of AlNiCo metallic film deposition on FCC Al substrate and subsequently nano-indentation on the same specimen considering different indenter velocities have been performed using Embedded Atom Method (EAM) potential. The mechanical properties and deformation behaviour of AlNiCo thin film deposited Al substrate is investigated subjected to simulated nano-indentation test. It has been found that indenter velocity significantly influences the calculated hardness of the thin film coated substrate specimen and faster indentation process increases the hardness of the specimen. This finding has been rationalised by correlating with the generation of various full and partial dislocations and their interactions during the nano-indentation process. Sessile dislocations such as stair-rod and Frank partials are found to aid/help the strain hardening phenomena. Furthermore, the effect of indenter velocity on the pile-up formation during the nano-indentation process is also investigated here and it is observed that the amount of pile-up reduces as indenter velocity increases.     

Effect of Joule Heating and Thermal Radiation in Flow of Third Grade Fluid over Radiative Surface

This article addresses the boundary layer flow and heat transfer in third grade fluid over an unsteady permeable stretching sheet. The transverse magnetic and electric fields in the momentum equations are considered. Thermal boundary layer equation includes both viscous and Ohmic dissipations. The related nonlinear partial differential system is reduced first into ordinary differential system and then solved for the series solutions. The dependence of velocity and temperature profiles on the various parameters are shown and discussed by sketching graphs. Expressions of skin friction coefficient and local Nusselt number are calculated and analyzed. Numerical values of skin friction coefficient and Nusselt number are tabulated and examined. It is observed that both velocity and temperature increases in presence of electric field. Further the temperature is increased due to the radiation parameter. Thermal boundary layer thickness increases by increasing Eckert number.     

Unsteady Boundary Layer Flow and Heat Transfer of a Casson Fluid past an Oscillating Vertical Plate with Newtonian Heating

In this paper, the heat transfer effect on the unsteady boundary layer flow of a Casson fluid past an infinite oscillating vertical plate with Newtonian heating is investigated. The governing equations are transformed to a systems of linear partial differential equations using appropriate non-dimensional variables. The resulting equations are solved analytically by using the Laplace transform method and the expressions for velocity and temperature are obtained. They satisfy all imposed initial and boundary conditions and reduce to some well-known solutions for Newtonian fluids. Numerical results for velocity, temperature, skin friction and Nusselt number are shown in various graphs and discussed for embedded flow parameters. It is found that velocity decreases as Casson parameters increases and thermal boundary layer thickness increases with increasing Newtonian heating parameter.     

Dehomogenized Elastic Properties of Heterogeneous Layered Materials in AFM Indentation Experiments

Atomic force microscopy (AFM) is used to study mechanical properties of biological materials at submicron length scales. However, such samples are often structurally heterogeneous even at the local level, with different regions having distinct mechanical properties. Physical or chemical disruption can isolate individual structural elements but may alter the properties being measured. Therefore, to determine the micromechanical properties of intact heterogeneous multilayered samples indented by AFM, we propose the Hybrid Eshelby Decomposition (HED) analysis, which combines a modified homogenization theory and finite element modeling to extract layer-specific elastic moduli of composite structures from single indentations, utilizing knowledge of the component distribution to achieve solution uniqueness. Using finite element model-simulated indentation of layered samples with micron-scale thickness dimensions, biologically relevant elastic properties for incompressible soft tissues, and layer-specific heterogeneity of an order of magnitude or less, HED analysis recovered the prescribed modulus values typically within 10% error. Experimental validation using bilayer spin-coated polydimethylsiloxane samples also yielded self-consistent layer-specific modulus values whether arranged as stiff layer on soft substrate or soft layer on stiff substrate. We further examined a biophysical application by characterizing layer-specific microelastic properties of full-thickness mouse aortic wall tissue, demonstrating that the HED-extracted modulus of the tunica media was more than fivefold stiffer than the intima and not significantly different from direct indentation of exposed media tissue. Our results show that the elastic properties of surface and subsurface layers of microscale synthetic and biological samples can be simultaneously extracted from the composite material response to AFM indentation. HED analysis offers a robust approach to studying regional micromechanics of heterogeneous multilayered samples without destructively separating individual components before testing.     

Wind Flow Characteristics on a Soybean Leaf Compared with a Leaf Model

The purpose of this paper is to describe momentum boundary layer flow parameters on a soybean leaf [Glycine max (L.) Merrill] at various velocities of the bulk air stream and these data are compared with similar measurements on an artificial leaf. The wind structure is measured at three different bulk air velocitìes (u_∞= 39, 148 and 271 centimeters per second) on an individual soybean leaf and is compared to structural effects on an artificial leaf (flat metal plate) in a small closed-circuit wind tunnel. The boundary layers were homogeneous for the metal plate, but only at the lower velocity for the soybean leaf. The boundary layer thicknesses decrease with increasing bulk air velocity for laminar flow regimes, whereas in the turbulent flow regime the boundary layer thickness greatly increases. The effect of turbulence on the soybean leaf boundary layer made the eddy diffusivities at least three times greater than in the laminar flow regime at the calculated roughness height above the leaf surface. The structure of the leaf boundary layer flow is comparable to that of the metal plate only at the lower bulk air velocity.     

Endothelial Glycocalyx Layer Properties and Its Ability to Limit Leukocyte Adhesion

The endothelial glycocalyx layer (EGL), which consists of long proteoglycans protruding from the endothelium, acts as a regulator of inflammation by preventing leukocyte engagement with adhesion molecules on the endothelial surface. The amount of resistance to adhesive events the EGL provides is the result of two properties: EGL thickness and stiffness. To determine these, we used an atomic force microscope to indent the surfaces of cultured endothelial cells with a glass bead and evaluated two different approaches for interpreting the resulting force-indentation curves. In one, we treat the EGL as a molecular brush, and in the other, we treat it as a thin elastic layer on an elastic half-space. The latter approach proved more robust in our hands and yielded a thickness of 110 nm and a modulus of 0.025 kPa. Neither value showed significant dependence on indentation rate. The brush model indicated a larger layer thickness (∼350 nm) but tended to result in larger uncertainties in the fitted parameters. The modulus of the endothelial cell was determined to be 3.0–6.5 kPa (1.5–2.5 kPa for the brush model), with a significant increase in modulus with increasing indentation rates. For forces and leukocyte properties in the physiological range, a model of a leukocyte interacting with the endothelium predicts that the number of molecules within bonding range should decrease by an order of magnitude because of the presence of a 110-nm-thick layer and even further for a glycocalyx with larger thickness. Consistent with these predictions, neutrophil adhesion increased for endothelial cells with reduced EGL thickness because they were grown in the absence of fluid shear stress. These studies establish a framework for understanding how glycocalyx layers with different thickness and stiffness limit adhesive events under homeostatic conditions and how glycocalyx damage or removal will increase leukocyte adhesion potential during inflammation.     

Nonlinear compliance of elastic layers to indentation

Thin samples adherent to a rigid substrate are considerably less compliant to indentation when compared to specimens that are not geometrically confined. Analytical corrections to this so-called substrate effect exist for various types of indenters but are not applicable when large deformations are possible, as is the case in biological materials. To overcome this limitation, we construct a nonlinear scaling model characterized by one single exponent, which we explore employing a parametric finite element analysis. The model is based on asymptotes of two length scales in relation to the sample thickness, i.e., indentation depth and radius of the contact area. For small indentation depth, we require agreement with analytical, linear models, whereas for large indentation depth and extensive contact area, we recognize similarity to uniaxial deformation, indicating a divergent force required to indent nonlinear materials. In contrast, we find linear materials not to be influenced by the substrate effect beyond first order, implying that nonlinear effects originating from either the material or geometric confinement are clearly separated only in thin samples. Furthermore, in this regime the scaling model can be derived by following a heuristic argument extending a linear model to large indentation depths. Lastly, in a large indentation setting where the contact is small in comparison with sample thickness, we observe nonlinear effects independent of material type that we attribute to a higher-order influence of geometrical confinement. In this regime, we define a scalar as the ratio of strains along principal axes as obtained by comparison with the case of a point force on a half-space. We find this scalar to be in quantitative agreement with the scaling exponent, indicating an approach to distinguish between nonlinear effects in the scaling model. While we conjecture our findings to be applicable to other flat-ended indenters, we focus on the case of a flat-ended cylinder in normal contact with a thin layer. The analytical solution for small indentation associated with this problem has been given by Hayes et al. (J Biomech 5:541–551, 1972), for which we provide a convenient numerical implementation.     

Cytochrome c adsorption to supported, anionic lipid bilayers studied via atomic force microscopy

The adsorption of membrane-associated protein cytochrome c to anionic lipid bilayers of dioleoyl phosphatidylglycerol was studied in low ionic strength physiological buffer using atomic force microscopy. The bilayers were supported on polylysinated mica. The formation of stable, single lipid bilayers was confirmed by imaging and force spectroscopy. Upon addition of low concentrations of cytochrome c, protein molecules were not topographically visible on the lipid bilayer-buffer interface. However, the forces required to punch through the bilayer by indentation using the atomic force microscopy probe were significantly lower after protein adsorption, which suggest that the protein inserts into the bilayer. Moreover, the apparent thickness of the bilayer remained unchanged after cytochrome c adsorption. Yet, mass spectroscopy and visible light absorption spectroscopy confirmed the presence of cytochrome c in the lipid bilayers. These results suggest that 1), cytochrome c inserts into the bilayer and resides in its hydrophobic core; 2), cytochrome c insertion changes the mechanical properties of the bilayer significantly; and 3), bilayer force spectroscopy may be a useful tool in investigating lipid-protein interactions.     

Kelvin-Helmholtz instability in a bounded plasma flow

Kelvin-Helmholtz instability in a three-layer plane geometry is investigated theoretically. It is shown that, in a three-layer system (in contrast to the traditionally considered case in which instability develops at the boundary between two plasma flows), instability can develop at an arbitrary ratio of the plasma flow velocity to the ion-acoustic velocity. Perturbations with wavelengths on the order of the flow thickness or longer can increase even at a zero temperature. The system can also be unstable against long-wavelength perturbations if the flow velocity at one of the boundaries is lower than the sum of the Alfvén velocities in the flow and the ambient plasma. The possibility of applying the results obtained to interpret the experimental data acquired in the framework of the CLUSTER multisatellite project is discussed. It follows from these data that, in many cases, the propagation of an accelerated particle flow in the plasma-sheet boundary layer of the Earth’s magnetotail is accompanied by the generation of magnetic field oscillations propagating with a velocity on the order of the local Alfvén velocity.     

Oscillatory Flow Accelerates Autocrine Signaling due to Nonlinear Effect of Convection on Receptor-Related Actions

We study effects of oscillatory convective flow in extracellular space on the velocity of chemical signal propagation having a form of a front wave above a cellular layer. We found that the time-averaged propagation velocity under oscillatory flow for a particular Péclet number amplitude is slower than the velocity under steady laminar flow regime for the same value of the Péclet number, but significantly faster than under no-flow conditions. We derive asymptotic values of the propagation velocity and asymptotic characteristics of the corresponding concentration fronts in high- and low-frequency regimes and show that the reason for the observed velocity increase under the oscillatory flow stems from a nonlinear dependence of the propagation velocity on the Péclet number, particularly from the convex character of the dependence. Our findings suggest that the specific responses of cellular cultures to different flow conditions in the extracellular space (for example, expression of atherosclerosis protective genes under steady laminar flow but not under oscillatory flow) is a consequence of a nonlinear coupling between the extracellular transport and complex intracellular reaction cascades forming a positive feedback loop of the autocrine signaling. This mechanism can operate independently of, or in conjunction with, a direct stress-sensing due to mechanotransduction.     

Oscillatory Flow Accelerates Autocrine Signaling due to Nonlinear Effect of Convection on Receptor-Related Actions

We study effects of oscillatory convective flow in extracellular space on the velocity of chemical signal propagation having a form of a front wave above a cellular layer. We found that the time-averaged propagation velocity under oscillatory flow for a particular Péclet number amplitude is slower than the velocity under steady laminar flow regime for the same value of the Péclet number, but significantly faster than under no-flow conditions. We derive asymptotic values of the propagation velocity and asymptotic characteristics of the corresponding concentration fronts in high- and low-frequency regimes and show that the reason for the observed velocity increase under the oscillatory flow stems from a nonlinear dependence of the propagation velocity on the Péclet number, particularly from the convex character of the dependence. Our findings suggest that the specific responses of cellular cultures to different flow conditions in the extracellular space (for example, expression of atherosclerosis protective genes under steady laminar flow but not under oscillatory flow) is a consequence of a nonlinear coupling between the extracellular transport and complex intracellular reaction cascades forming a positive feedback loop of the autocrine signaling. This mechanism can operate independently of, or in conjunction with, a direct stress-sensing due to mechanotransduction.     

Steady propagation of a liquid plug in a two-dimensional channel

In this study, we investigate the steady propagation of a liquid plug within a two-dimensional channel lined by a uniform, thin liquid film. The Navier-Stokes equations with free-surface boundary conditions are solved using the finite volume numerical scheme. We examine the effect of varying plug propagation speed and plug length in both the Stokes flow limit and for finite Reynolds number (Re). For a fixed plug length, the trailing film thickness increases with plug propagation speed. If the plug length is greater than the channel width, the trailing film thickness agrees with previous theories for semi-infinite bubble propagation. As the plug length decreases below the channel width, the trailing film thickness decreases, and for finite Re there is significant interaction between the leading and trailing menisci and their local flow effects. A recirculation flow forms inside the plug core and is skewed towards the rear meniscus as Re increases. The recirculation velocity between both tips decreases with the plug length. The macroscopic pressure gradient, which is the pressure drop between the leading and trailing gas phases divided by the plug length, is a function of U and U2, where U is the plug propagation speed, when the fluid property and the channel geometry are fixed. The U2 term becomes dominant at small values of the plug length. A capillary wave develops at the front meniscus, with an amplitude that increases with Re, and this causes large local changes in wall shear stresses and pressures.     

Temperature Dependent Mechanical Property of PZT Film: An Investigation by Nanoindentation

Load-depth curves of an unpoled Lead Zirconate Titanate (PZT) film composite as a function of temperature were measured by nanoindentation technique. Its reduce modulus and hardness were calculated by the typical Oliver-Pharr method. Then the true modulus and hardness of the PZT film were assessed by decoupling the influence of substrate using methods proposed by Zhou et al. and Korsunsky et al., respectively. Results show that the indentation depth and modulus increase, but the hardness decreases at elevated temperature. The increasing of indentation depth and the decreasing of hardness are thought to be caused by the decreasing of the critical stress needed to excite dislocation initiation at high temperature. The increasing of true modulus is attributed to the reducing of recoverable indentation depth induced by back-switched domains. The influence of residual stress on the indentation behavior of PZT film composite was also investigated by measuring its load-depth curves with pre-load strains.     

Effect of temperature on cross-bridge properties in intact frog muscle fibers

It is well known that the force developed by skeletal muscles increases with temperature. Despite the work done on this subject, the mechanism of force potentiation is still debated. Most of the published papers suggest that force enhancement is due to the increase of the individual cross-bridge force. However, reports on skinned fibers and single-molecule experiments suggest that cross-bridge force is temperature independent. The effects of temperature on cross-bridge properties in intact frog fibers were investigated in this study by applying fast stretches at various tension levels (P) on the tetanus rise at 5 degrees C and 14 degrees C to induce cross-bridge detachment. Cross-bridge number was measured from the force (critical force, P(c)) needed to detach the cross-bridge ensemble, and the average cross-bridge strain was calculated from the sarcomere elongation needed to reach P(c) (critical length, L(c)). Our results show that P(c) increased linearly with the force developed at both temperatures, but the P(c)/P ratio was considerably smaller at 14 degrees C. This means that the average force per cross bridge is greater at high temperature. This mechanism accounts for all the tetanic force enhancement. The critical length L(c) was independent of the tension developed at both temperatures but was significantly lower at high temperature suggesting that cross bridges at 14 degrees C are more strained. The increased cross-bridge strain accounts for the greater average force developed.     

Probing softness of the parietal pleural surface at the micron scale

The pleural surfaces of the chest wall and lung slide against each other, lubricated by pleural fluid. During sliding motion of soft tissues, shear induced hydrodynamic pressure deforms the surfaces, promoting uniformity of the fluid layer thickness, thereby reducing friction. To assess pleural deformability at length scales comparable to pleural fluid thickness, we measured the modulus of the parietal pleura of rat chest wall using atomic force microscopy (AFM) to indent the pleural surface with spheres (radius 2.5 and 5 μm). The pleura exhibited two distinct indentation responses depending on location, reflecting either homogeneous or significantly heterogeneous tissue properties. We found an elastic modulus of 0.38-0.95 kPa, lower than the values measured using flat-ended cylinders >100 μm radii (Gouldstone et al., 2003, Journal of Applied Physiology 95, 2345-2349). Interestingly, the pleura exhibited a three-fold higher modulus when probed using 2.5 vs. 5 μm spherical tips at the same normalized depth, confirming depth dependent inhomogeneous elastic properties. The observed softness of the pleura supports the hypothesis that unevenness of the pleural surface on this scale is smoothed by local hydrodynamic pressure.     

Kinematic and kinetic analysis of maximal velocity deadlifts performed with and without the inclusion of chain resistance

The purpose of this study was to investigate whether the deadlift could be effectively incorporated with explosive resistance training (ERT) and to investigate whether the inclusion of chains enhanced the suitability of the deadlift for ERT. Twenty-three resistance trained athletes performed the deadlift with 30, 50, and 70% 1-repetition maximum (1RM) loads at submaximal velocity, maximal velocity (MAX), and MAX with the inclusion of 2 chain loads equal to 20 or 40% of the subjects' 1RM. All trials were performed on force platforms with markers attached to the barbell to calculate velocity and acceleration using a motion capture system. Significant increases in force, velocity, power, rate of force development, and length of the acceleration phase (p < 0.05) were obtained when repetition velocity increased from submaximal to maximal. During MAX repetitions with a constant resistance, the mean length of the acceleration phase ranged from 73.2 (±7.2%) to 84.9 (±12.2%) of the overall movement. Compared to using a constant resistance, the inclusion of chains enabled greater force to be maintained to the end of the concentric action and significantly increased peak force and impulse (p < 0.05), while concurrently decreasing velocity, power, and rate of force development (p < 0.05). The effects of chains were influenced by the magnitude of the chain and barbell resistance, with greater increases and decreases in mechanical variables obtained when heavier chain and barbell loads were used. The results of the investigation suggest that the deadlift can be incorporated effectively in ERT programs. Coaches and athletes should be aware that the inclusion of heavy chains may have both positive and negative effects on kinematics and kinetics of an exercise.     

The influence of radial RBC distribution, blood velocity profiles, and glycocalyx on coupled NO/O2 transport.

The purpose of this investigation was to study the effect of the presence of red blood cells (RBCs) in the plasma layer near the arteriole wall on nitric oxide (NO) and oxygen (O2) transport. To this end, we extended a coupled NO and O2 diffusion-reaction model in the arteriole, developed by our group, to include the effect of the presence of RBCs in the plasma layer and the effect of convection. Two blood flow velocity profiles (plug and parabolic) were tested. The average hematocrit in the bloodstream was assumed to be constant in the central core and decreasing to zero in the boundary layer next to the endothelial surface layer. The effect of the presence or absence of RBCs near the endothelium was studied while varying the endothelial surface layer and boundary layer thickness. With RBCs present in the boundary layer, the model predicts that 1) NO decreases significantly in the endothelium and vascular wall; 2) there is a very small increase in endothelial and vascular wall Po2; 3) scavenging of NO by hemoglobin decreases with increasing thickness of the boundary layer; 4) the shape of the velocity profile influences both NO and Po2 gradients in the bloodstream; and 5) the presence of RBCs in the boundary layer near the endothelium has a much larger effect on NO than on O2 transport.     

Cell-substrate separation: effect of applied force and temperature

We measure the change in cell-substrate separation in response to an upward force by combining two relatively new techniques, Electric Cell-substrate Impedance Sensing (ECIS) to measure average cell-substrate separation, and collagen-coated magnetic beads to apply force to the top (dorsal) surface of cells. The collagen-coated ferric oxide beads attach to integrin receptors in the dorsal surfaces of osteoblastlike ROS 17/2.8 cells. Magnetic force is controlled by the position and the number of permanent magnets, applying an average 320 or 560 pN per cell. Comparing model calculations with experimental impedance data, the junctional resistivity of the cell layer and the average distance between the lower (ventral) cell surface and substrate can be determined. The ECIS analysis shows that these forces produce an increase in the distance between the ventral cell surface and the substrate that is in the range of 10 to 25%. At temperatures of 4°, 22° and 37 °C, the measured cell surface-substrate distances without magnetic beads are 84 ± 4, 45 ± 2 and 38 ± 2 nm. The force-induced changes at 22° are 11 ± 3 and 21 ± 3 nm for 320 and 560 pN, and at 37° they are 5 ± 2 and 9 ± 2 nm. The resulting cell-substrate spring constants at 22° and 37° are thus about 28 and 63 pN nm^–1 (dyne cm^–1). Using a reasonable range for the number for individual integrin-ligand adhesion bonds gives a range for the spring constant of the individual adhesion bond of from about 10^–3 to 10^–1 pN nm^–1. These data also provide evidence that the number of adhesion bonds per cell increases with temperature. Received: 20 June 1997 / Accepted: 24 August 1997     

Slip Effects on Mixed Convective Peristaltic Transport of Copper-Water Nanofluid in an Inclined Channel

Peristaltic transport of copper-water nanofluid in an inclined channel is reported in the presence of mixed convection. Both velocity and thermal slip conditions are considered. Mathematical modelling has been carried out using the long wavelength and low Reynolds number approximations. Resulting coupled system of equations is solved numerically. Quantities of interest are analyzed through graphs. Numerical values of heat transfer rate at the wall for different parameters are obtained and examined. Results showed that addition of copper nanoparticles reduces the pressure gradient, axial velocity at the center of channel, trapping and temperature. Velocity slip parameter has a decreasing effect on the velocity near the center of channel. Temperature of nanofluid increases with increase in the Grashoff number and channel inclination angle. It is further concluded that the heat transfer rate at the wall increases considerably in the presence of copper nanoparticles.