Effects of body configuration on pelvic injury in backward fall simulation using 3D finite element models of pelvis–femur–soft tissue complex

Injuries due to backward fall apart from sideways fall are a major health problem, particularly among the aged populations. The objectives of this study was to evaluate the responses to changing body configurations (angle between the trunk and impacting floor as 0°, 15°, 45° and 80°) during backward fall, based on a previously developed CT-scan-derived 3D non-linear and non-homogeneous finite element (FE) model of pelvis–femur–soft tissue complex with simplified biomechanical representation of the whole body. Under constant impact energy, these FE models evaluated the pelvic injury situations on the basis of peak impact force (7.64–16.74 kN) and peak principal compressive strain (more than 1.5%), consistent with the clinically observed injuries (sacral insufficiency, coccydynia). Also the change in location of peak strain and increase in peak impact force for changing configurations from 0° to 80° indicated the effect of whole body inertia during backward fall. It was also concluded that the inclusion of sacro-iliac and acetabular cartilages in the above FE models will further reduce above findings marginally (9.2% for 15° fall). These quantifications would also be helpful for a better design and development of safety structures such as safety floor for the nursing home or home for the aged persons.     

Predicting cell viability within tissue scaffolds under equiaxial strain: multi-scale finite element model of collagen–cardiomyocytes constructs

Biomechanics and Modeling in Mechanobiology - Successful tissue engineering and regenerative therapy necessitate having extensive knowledge about mechanical milieu in engineered tissues and the...     

A method for assessing the fit of a constitutive material model to experimental stress–strain data

Higher-order polynomial functions can be used as a constitutive model to represent the mechanical behaviour of biological materials. The goal of this study was to present a method for assessing the fit of a given constitutive three-dimensional material model. Goodness of fit was assessed using multiple parameters including the root mean square error and Hotelling's T ²-test. Specifically, a polynomial model was used to characterise the stress–strain data, varying the number of model terms used (45 combinations of between 3 and 11 terms) and the manner of optimisation used to establish model coefficients (i.e. determining coefficients either by parameterisation of all data simultaneously or averaging coefficients obtained by parameterising individual data trials). This framework for model fitting helps to ensure that a given constitutive formulation provides the best characterisation of biological material mechanics.     

Three-dimensional finite element analysis of stress distribution in retention screws of different crown–implant ratios

The retaining screw of the implant-supported dental prosthesis is the weakest point of the crown/implant system. Furthermore, crown height is another important factor that may increase the lever arm. Therefore, the aim of this study was to assess the stress distribution in implant prosthetic screws with different heights of the clinical crown of the prosthesis using the method of three-dimensional finite element analysis. Three models were created with implants (3.75 mm × 10 mm) and crowns (heights of 10, 12.5 and 15 mm). The results were visualised by means of von Mises stress maps that increased the crown heights. The screw structure exhibited higher levels of stresses in the oblique load. The oblique loading resulted in higher stress concentration when compared with the axial loading. It is concluded that the increase of the crown was damaging to the stress distribution on the screw, mainly in oblique loading.     

Probabilistic failure analysis of bone using a finite element model of mineral–collagen composites

Microdamage accumulation is a major pathway for energy dissipation during the post-yield deformation of bone. In this study, a two-dimensional probabilistic finite element model of a mineral–collagen composite was developed to investigate the influence of the tissue and ultrastructural properties of bone on the evolution of microdamage from an initial defect in tension. The probabilistic failure analyses indicated that the microdamage progression would be along the plane of the initial defect when the debonding at mineral–collagen interfaces was either absent or limited in the vicinity of the defect. In this case, the formation of a linear microcrack would be facilitated. However, the microdamage progression would be scattered away from the initial defect plane if interfacial debonding takes place at a large scale. This would suggest the possible formation of diffuse damage. In addition to interfacial debonding, the sensitivity analyses indicated that the microdamage progression was also dependent on the other material and ultrastructural properties of bone. The intensity of stress concentration accompanied with microdamage progression was more sensitive to the elastic modulus of the mineral phase and the nonlinearity of the collagen phase, whereas the scattering of failure location was largely dependent on the mineral to collagen ratio and the nonlinearity of the collagen phase. The findings of this study may help understanding the post-yield behavior of bone at the ultrastructural level and shed light on the underlying mechanism of bone fractures.     

Influence of altered geometry and material properties on tissue stress distribution under load in tendinopathic Achilles tendons – A subject-specific finite element analysis

Achilles tendon material properties and geometry are altered in Achilles tendinopathy. The purpose of this study was to determine the relative contributions of altered material properties and geometry to free Achilles tendon stress distribution during a sub-maximal contraction in tendinopathic relative to healthy tendons. Tendinopathic (n = 8) and healthy tendons (n = 8) were imaged at rest and during a sub-maximal voluntary isometric contraction using three-dimensional freehand ultrasound. Images were manually segmented and used to create subject-specific finite element models. The resting cross-sectional area of the free tendon was on average 31% greater for the tendinopathic compared to healthy tendons. Material properties for each tendon were determined using a numerical parameter optimisation approach that minimised the difference in experimentally measured longitudinal strain and the strain predicted by the finite element model under submaximal loading conditions for each tendon. The mean Young’s modulus for tendinopathic tendons was 53% lower than the corresponding control value. Finite element analyses revealed that tendinopathic tendons experience 24% less stress under the same submaximal external loading conditions compared to healthy tendons. The lower tendon stress in tendinopathy was due to a greater influence of tendon cross-sectional area, which alone reduced tendon stress by 30%, compared to a lower Young’s modulus, which alone increased tendon stress by 8%. These findings suggest that the greater tendon cross-sectional area observed in tendinopathy compensates for the substantially lower Young’s modulus, thereby protecting pathological tendon against excessive stress.     

Modelling the effects of hydrogen passivation and strain on the field emission from armchair-graphene nanoribbon using a modified non-equilibrium Green’s function method

In this report, we introduced a modified non-equilibrium Green’s function method to investigate the structural effects on the field emission current from an armchair graphene nanoribbon. We introduce a modified self-energy which is useful to study the effects of potential barrier in the field emission devices. Investigation into the effects of hydrogen passivation and applied strain can be realised using our modified formalism. Also a practical method to consider the effect of device parameters, such as channel length, anode–cathode separation and gate potential can be provided by the proposed formalism. The quantum effects of the emitter’s structure on the field emission are achievable by our introduced method.     

Wall stress and flow dynamics in abdominal aortic aneurysms: finite element analysis vs. fluid–structure interaction

Abdominal aortic aneurysm (AAA) rupture is the clinical manifestation of an induced force exceeding the resistance provided by the strength of the arterial wall. This force is most frequently assumed to be the product of a uniform luminal pressure acting along the diseased wall. However fluid dynamics is a known contributor to the pathogenesis of AAAs, and the dynamic interaction of blood flow and the arterial wall represents the in vivo environment at the macro-scale. The primary objective of this investigation is to assess the significance of assuming an arbitrary estimated peak fluid pressure inside the aneurysm sac for the evaluation of AAA wall mechanics, as compared with the non-uniform pressure resulting from a coupled fluid–structure interaction (FSI) analysis. In addition, a finite element approach is utilised to estimate the effects of asymmetry and wall thickness on the wall stress and fluid dynamics of ten idealised AAA models and one non-aneurysmal control. Five degrees of asymmetry with uniform and variable wall thickness are used. Each was modelled under a static pressure-deformation analysis, as well as a transient FSI. The results show that the inclusion of fluid flow yields a maximum AAA wall stress up to 20% higher compared to that obtained with a static wall stress analysis with an assumed peak luminal pressure of 117 mmHg. The variable wall models have a maximum wall stress nearly four times that of a uniform wall thickness, and also increasing with asymmetry in both instances. The inclusion of an axial stretch and external pressure to the computational domain decreases the wall stress by 17%.     

Development of a geometrically accurate and adaptable finite element head model for impact simulation: the Naval Research Laboratory–Simpleware Head Model

This study demonstrates a novel model generation methodology that addresses several limitations of conventional finite element head models (FEHM). By operating chiefly in image space, new structures can be incorporated or merged, and the mesh either decimated or refined both locally and globally. This methodology is employed in the development of a highly bio-fidelic FEHM from high-resolution scan data. The model is adaptable and presented here in a form optimised for impact and blast simulations. The accuracy and feasibility of the model are successfully demonstrated against a widely used experimental benchmark in impact loading and through the investigation of potential brain injury under blast overpressure loading.     

The effect of direct and indirect force transmission on peri-implant bone stress – a contact finite element analysis

In almost all finite element (FE) studies in dentistry, virtual forces are applied directly to dentures. The purpose of this study was to develop a FE model with non-linear contact simulation using an antagonist as force transmitter and to compare this with a similar model that uses direct force transmission. Furthermore, five contact situations were created in order to examine their influence on the peri-implant bone stresses, which are relevant to the survival rate of implants. It was found that the peri-implant bone stresses were strongly influenced by the kind of force transmission and contact number.     

Oxidized and reduced nicotinamide–adenine dinucleotide phosphate in tissue suspensions of rat liver

1. The concentrations of NADP and NADPH(2) in homogenates of rat liver (expressed as mug./g. wet wt. of tissue homogenized) were compared with values obtained from intact samples of liver taken from the same female rat. With 0.25m-sucrose alone as the suspending medium, or in combination with tris buffer or 0.01-0.1m-nicotinamide, considerable decreases in the sum of the NADP+NADPH(2) concentrations were occasionally observed during 30min. storage of homogenates at 0 degrees . However, addition of 0.5m-nicotinamide+5mm-tris buffer to 0.25m-sucrose for use as a suspending medium maintained the sum of the NADP+NADPH(2) concentrations in homogenates at the level found in intact tissue for at least 30min. at 0 degrees . 2. The effects of freezing intact tissue and homogenates in liquid nitrogen before the extraction of NADP and NADPH(2) were studied. Freezing alone appears to convert a significant amount (approx. 30%) of liver NADPH(2) into an equivalent amount of NADP in intact tissue. This is discussed in terms of the ;bound NADP' reported by Burch, Lowry & Von Dippe (1963). 3. The intracellular distributions of NADP and NADPH(2) in intracellular fractions of rat liver were studied by using a modified centrifuging scheme that allows extraction of the isolated fractions to be performed within 45min. of killing the animal. Approx. 50% of the total NADP+NADPH(2) was found in the large-particle fractions and the remaining 50% was mostly in the soluble fraction of the cell. 4. Further investigations are reported on the nature of ;bound NADP' in rat liver. Most of this material appears associated with the ;nuclear' (containing nuclei, debris, erythrocytes etc.) or large-mitochondrial fractions, or both, obtained by low-speed centrifuging of rat-liver homogenates. 5. Although in some experiments the variations produced in the concentration of NADPH(2) present in large-particle fractions were followed by similar changes in that of ;bound NADP', in other cases no such direct relationship was obtained. Addition of phenazine methosulphate, for example, consistently lowered the concentration of NADPH(2) yet raised the concentration of ;bound NADP' in rat-liver mitochondrial fractions.     

Survival and fidelity of an enclosed white-tailed deer population using capture–recapture-reporting data

The number of animal populations enclosed by impermeable fences has increased, which poses issues related to the behavior of individuals and populations. Despite the increased number of fenced enclosures, there is a paucity of survival and fidelity data on white-tailed deer (Odocoileus virginianus) from fenced enclosures. Therefore, we examined marked deer recaptures and resightings over 13 years for an enclosed population of white-tailed deer in Oklahoma, USA, to estimate survival and fidelity parameters. We found that a step model was the best model of survival for both sexes. Survival of females and males was greater after hunting was suspended. Average female survival was 77% before hunting was suspended but increased to 98% after. Male survival was also greater after (99%) hunting was suspended compared to before (58%). Females exhibited greater site fidelity (84–94%) than males for all age groups except old individuals, which showed similar site fidelities for males and females. Fidelity was highest for old males (85%), followed by adult (74%), fawn (61%), and yearling males (56%). Our high-tensile electric fence allowed management goals to be achieved through increased survival while potentially maintaining genetic diversity through the exchange of limited numbers of individuals from surrounding areas. However, if the goal is to confine deer to limit disease spread or protect sensitive areas (e.g., airports) from deer encroachment, then other fence designs may be necessary, because our fence was not completely effective at controlling deer movements for these purposes.     

Degradation of insulin in vitro by liver and epididymal adipose tissue from obese–hyperglycaemic mice

The insulin-degrading activity of liver supernatants and epididymal adipose-tissue homogenates from genetically obese–hyperglycaemic mice (ob ob) and their lean litter mates was studied by measurement of radioactive trichloroacetic acid-soluble degradation products of the insulin molecule. Optimum assay conditions for the decomposition of the hormone were devised. The properties of the degrading activity suggested the presence of enzymic insulin destruction in both the liver and epididymal adipose tissue. There was no difference in insulin degradation in liver samples from obese and lean mice when the results were related to the protein content of the supernatants. The epididymal adipose-tissue homogenates from obese mice displayed about eightfold higher degrading activity per unit of protein than did homogenates from lean animals. The physiological significance of this finding is discussed in the light of the increased fat depots, hyperphagia, raised serum insulin concentrations and increased insulin tolerance previously recorded in this strain of mice.     

Modeling of the structure of protein–DNA complexes using the data from FRET and footprinting experiments

We discuss the question of constructing three-dimensional models of DNA in complex with proteins using computer modeling and indirect methods of studying the conformation of macromolecules. We consider the methods of interpreting the experimental data obtained by indirect methods of studying the three-dimensional structure of biomolecules. We discuss some aspects of integrating such data into the process of constructing the molecular models of DNA–protein complexes based on the geometric characteristics of DNA. We propose an algorithm for estimating conformations of such complexes based on the information about the local flexibility of DNA and on the experimental data obtained by Forster resonance energy transfer (FRET) and hydroxyl footprinting. Finally, we use this algorithm to predict the hypothetical configuration of DNA in a nucleosome bound with histone H1.     

Modeling and simulation of enzymatic gluconic acid production using immobilized enzyme and CSTR–PFTR circulation reaction system

Objectives

Production of gluconic acid by using immobilized enzyme and continuous stirred tank reactor-plug flow tubular reactor (CSTR–PFTR) circulation reaction system.

Results

A production system is constructed for gluconic acid production, which consists of a continuous stirred tank reactor (CSTR) for pH control and liquid storage and a plug flow tubular reactor (PFTR) filled with immobilized glucose oxidase (GOD) for gluconic acid production. Mathematical model is developed for this production system and simulation is made for the enzymatic reaction process. The pH inhibition effect on GOD is modeled by using a bell-type curve.

Conclusions

Gluconic acid can be efficiently produced by using the reaction system and the mathematical model developed for this system can simulate and predict the process well.

     

Carotid arterial plaque stress analysis using fluid–structure interactive simulation based on in-vivo magnetic resonance images of four patients

The rupture of atherosclerotic plaques is known to be associated with the stresses that act on or within the arterial wall. The extreme wall tensile stress (WTS) is usually recognized as a primary trigger for the rupture of vulnerable plaque. The present study used the in-vivo high-resolution multi-spectral magnetic resonance imaging (MRI) for carotid arterial plaque morphology reconstruction. Image segmentation of different plaque components was based on the multi-spectral MRI and co-registered with different sequences for the patient. Stress analysis was performed on totally four subjects with different plaque burden by fluid–structure interaction (FSI) simulations. Wall shear stress distributions are highly related to the degree of stenosis, while the level of its magnitude is much lower than the WTS in the fibrous cap. WTS is higher in the luminal wall and lower at the outer wall, with the lowest stress at the lipid region. Local stress concentrations are well confined in the thinner fibrous cap region, and usually locating in the plaque shoulder; the introduction of relative stress variation during a cycle in the fibrous cap can be a potential indicator for plaque fatigue process in the thin fibrous cap. According to stress analysis of the four subjects, a risk assessment in terms of mechanical factors could be made, which may be helpful in clinical practice. However, more subjects with patient specific analysis are desirable for plaque-stability study.     

Inhibition of neutral sphingomyelinase decreases elevated levels of nitrative and oxidative stress markers in liver ischemia–reperfusion injury

Oxidative stress and excessive nitric oxide production via induction of inducible nitric oxide synthase (NOS)-2 have been shown in the pathogenesis of liver ischemia–reperfusion (IR) injury. Neutral sphingomyelinase (N-SMase)/ceramide pathway can regulate NOS2 expression therefore this study determined the role of selective N-SMase inhibition on nitrative and oxidative stress markers following liver IR injury. Selective N-SMase inhibitor was administered via intraperitoneal injections. Liver IR injury was created by clamping blood vessels supplying the median and left lateral hepatic lobes for 60 min, followed by 60 min reperfusion. Nitrative and oxidative stress markers were determined by evaluating NOS2 expression, protein nitration, nitrite/nitrate levels, 4-hydroxynonenal (HNE) formation, protein carbonyl levels and xanthine oxidase/xanthine dehydrogenase (XO/XDH) activity. Levels of sphingmyelin and ceramide in liver tissue were determined by an optimized multiple reaction monitoring method using ultra-fast liquid chromatography coupled with tandem mass spectrometry (MS/MS). Spingomyelin levels were significantly increased in all IR groups compared to controls. Treatment with a specific N-SMase inhibitor significantly decreased all measured ceramides in IR injury. NOS2 expression, nitrite/nitrate levels and protein nitration were significantly greater in IR injury and decreased with N-SMase inhibition. Treatment with a selective N-SMase inhibitor significantly decreased HNE formation, protein carbonyl levels and the hepatic conversion of XO. Data confirm the role of nitrative and oxidative injury in IR and highlight the protective effect of selective N-SMase inhibition. Future studies evaluating agents blocking N-SMase activity can facilitate the development of treatment strategies to alleviate oxidative injury in liver I/R injury.