Effect of hydroxypropyl methylcellulose and hydrogenated castor oil on naproxen release from sustained-release tablets

The effect of the concentration of hydrophilic (hydroxypropyl methylcellulose [HPMC]) and hydrophobic (hydrogenated castor oil [HCO]) products, fillers (lactose and dibasic calcium phosphate), and buffers (sodium bicarbonate, calcium carbonate, and sodium citrate) on naproxen release rate was studied. Matrix tablets were prepared by double compression, andIn vitro dissolution tests were performed. The dissolution results showed that an increased amount of HPMC or hydrogenated castor oil resulted in reduced drug release. The inclusion of buffers in the HPMC matrix tablets enhanced naproxen release. For HCO tablets, only sodium bicarbonate enhanced naproxen release. The presence of lactose on HPMC matrix tablets did not show a significantly different result from that obtained with the formulation containing dibasic calcium phosphate as a filler. However, for the tablets containing HCO, the presence of lactose significantly enhanced the naproxen release rate. The matrix-forming materials in this study were suitable for use in sustained-release tablets containing naproxen. The drug release can be modulated by adding suitable amounts of diluents and buffers.     

Matrix Tablets: The Effect of Hydroxypropyl Methylcellulose/Anhydrous Dibasic Calcium Phosphate Ratio on the Release Rate of a Water-Soluble Drug Through the Gastrointestinal Tract I. In Vitro Tests

Different hydroxypropyl methylcellulose (HPMC)/anhydrous dibasic calcium phosphate (ADCP) matrix tablets have been developed aiming to evaluate the influence of both components ratio in the control release of a water-soluble drug (theophylline). In order to characterise the matrix tablets, swelling, buoyancy and dissolution studies have been carried out in different aqueous media (demineralised water, progressive pH medium, simulated gastric fluid, simulated intestinal fluid and simulated colonic fluid). The HPMC/ADCP ratio has turned out to be the determinant in the matrix behaviour: the HPMC characteristic swelling behaviour was modulated, in some cases, by the ADCP characteristic acidic dissolution. When the HPMC/ADCP ratio was ≥0.69, buoyancy, continuous swelling and low theophylline dissolution rate from the matrices (H1, H2 and H3) were observed in all dissolution media. Consequently, these formulations could be adequate as gastro-retentive drug delivery systems. Additionally, HPMC/ADCP ratio ≤0.11 (H5 and H6) induces a pH-dependent drug release which could be applied to design control drug release enteric formulations (with a suitable enteric coating). Finally, a HPMC/ADCP ratio between 0.11 and 0.69 (H4) yield a gastrointestinal controlled drug release, due to its time-dependent buoyancy (7 h) and a total drug delivery in 17 h in simulated colonic fluid.Key words: anhydrous dibasic calcium phosphate, hydroxypropyl methylcellulose, matrix tablets, oral controlled release, theophylline     

Effect of microenvironment pH of swellable and erodable buffered matrices on the release characteristics of diclofenac sodium

The aim of this work is to design pH-dependent swellable and erodable-buffered matrices and to study the effect of the microenvironment pH on the release pattern of diclofenac sodium. Buffered matrix tablets containing diclofenac sodium, physically mixed with hydrophilic polymer (hydroxypropyl methylcellulose [HPMC]) and pH-dependent solubility polymer (Eudragit L100-55) were prepared with different microenvironment pHs. The release of diclofenac sodium from the buffer matrices was studied in phosphate buffer solutions of pH 5.9 and 7.4. The swelling and erosion matrices containing only HPMC and Eudragit L100-55 were studied in phosphate buffer solution of pH similar to the microenvironment pHs of the matrices. Drug release from matrices was found to be linear as a function of time. Amount of drug released was found to be higher in the medium of pH 7.4 than that of pH 5.9. The rate of drug release increased with the increase of the microenvironment pH of the matrices as determined from the slope. The pattern of drug release did not change with the change of microenvironment pH. The swelling and erosion occurred simultaneously from matrices made up of HPMC and Eudragit L100-55. Both extent of swelling and erosion increased with increase of the medium pH. It was concluded from this study that changing the pH within the matrix influenced the rate of release of the drug without affecting the release pattern. Fax: Not Forwarded     

Controlled release formulation of tramadol hydrochloride using hydrophilic and hydrophobic matrix system

The effect of concentration of hydrophilic (hydroxypropyl methylcellulose [HPMC]) and hydrophobic polymers (hydrogenated castor oil [HCO], ethylcellulose) on the release rate of tramadol was studied. Hydrophilic matrix tablets were prepared by wet granulation technique, while hydrophobic (wax) matrix tablets were prepared by melt granulation technique and in vitro dissolution studies were performed using United States Pharmacopeia (USP) apparatus type II. Hydrophobic matrix tablets resulted in sustained in vitro drug release (>20 hours) as compared with hydrophilic matrix tablets (<14 hours). The presence of ethylcellulose in either of the matrix systems prolonged the release rate of the drug. Tablets prepared by combination of hydrophilic and hydrophobic polymers failed to prolong the drug release beyond 12 hours. The effect of ethylcellulose coating (Surelease) and the presence of lactose and HPMC in the coating composition on the drug release was also investigated. Hydrophobic matrix tablets prepared using HCO were found to be best suited for modulating the delivery of the highly water-soluble drug, tramadol hydrochloride.     

Evaluation of Mimosa pudica Seed Mucilage as Sustained-Release Excipient

The present study was conducted to investigate the sustained-release properties of Mimosa pudica seed mucilage. Matrix tablets of diclofenac sodium containing different proportions of mucilage and dibasic calcium phosphate as diluent were formulated by wet granulation method. The tablets had uniform physical appearance, average weight, drug content, and adequate hardness. The results of in vitro release conducted using USP type II dissolution rate apparatus, in a dissolution media comprising of 900 mL of 0.1 N HCl for 2 h followed by phosphate buffer (pH 6.8) for 24 h at 37°C and 50 rpm, revealed that as the proportion of mucilage in the matrix was increased there was a corresponding decrease in the release of drug. Further, the matrix tablets were found to release the drug following Higuchi square root release kinetics, with the mechanism of release being diffusion for tablets containing higher proportion of mucilage and a combination of matrix erosion and diffusion for tablets containing smaller proportion of mucilage. The swelling and erosion studies revealed that, as the proportion of mucilage in tablets was increased, there was a corresponding increase in percent swelling and a decrease in percent erosion of tablets. The SEM photomicrographs showed gelling structures in tablets containing higher percentage of mucilage, while both pores and gelling structures were present on the surface of tablets containing smaller proportion of mucilage and commercial formulation. On comparative evaluation, the dissolution profile from formulation containing mucilage to drug in the proportion of 1:40 was found to be similar to the commercial sustained-release formulation of diclofenac.     

Effects of Processing on the Release Profiles of Matrix Systems Containing 5-Aminosalicylic Acid

The aim of this study was to investigate the influence of different processing methods on the profiles of 5-aminosalicylic acid dissolution from controlled-release matrix systems based on Eudragit® RL and Eudragit® RS water-insoluble polymers. The pure polymers and their mixtures were studied as matrix formers using different processing methods, i.e., direct compression, wet granulation of the active ingredient with the addition of polymer(s) to the external phase, wet granulation with water, and wet granulation with aqueous dispersions. In comparison with the directly compressed tablets, tablets made by wet granulation with water demonstrated a 6–19% increase in final drug dissolution, whereas when polymers were applied in the external phase during compression, a 0–13% decrease was observed in the amount of drug released. Wet granulation with aqueous polymer dispersions delayed the release of the drug; this was especially marked (a 54–56% decrease in drug release) in compositions, which contained a high amount of Eudragit RL 30D. The release profiles were mostly described by the Korsmeyer–Peppas model or the Hopfenberg model.KEY WORDS: controlled release, matrix tablet, polymethacrylates, release kinetics     

Once-daily sustained-release matrix tablets of nicorandil: Formulation and in vitro evaluation

The objective of the present study was to develop once-daily sustained-release matrix tablets of nicorandil, a novel potassium channel opener used in cardiovascular diseases. The tablets were prepared by the wet granulation method. Ethanolic solutions of ethylcellulose (EC), Eudragit RL-100, Eudragit RS-100, and polyvinylpyrrolidone were used as granulating agents along with hydrophilic matrix materials like hydroxypropyl methylcellulose (HPMC), sodium carboxymethylcellulose, and sodium alginate. The granules were evaluated for angle of repose, bulk density, compressibility index, total porosity, and drug content. The tablets were subjected to thickness, diameter, weight variation test, drug content, hardness, friability, and in vitro release studies. The granules showed satisfactory flow properties, compressibility, and drug content. All the tablet formulations showed acceptable pharmacotechnical properties and complied with in-house specifications for tested parameters. According to the theoretical release profile calculation, a oncedaily sustained-release formulation should release 5.92 mg of nicorandil in 1 hour, like conventional tablets, and 3.21 mg per hour up to 24 hours. The results of dissolution studies indicated that formulation F-I (drug-to-HPMC, 1∶4; ethanol as granulating agent) could extend the drug release up to 24 hours. In the further formulation development process, F-IX (drug-to-HPMC, 1∶4; EC 4% wt/vol as granulating agent), the most successful formulation of the study, exhibited satisfactory drug release in the initial hours, and the total release pattern was very close to the theoretical release profile. All the formulations (except F-IX) exhibited diffusion-dominated drug release. The mechanism of drug release from F-IX was diffusion coupled with erosion.     

Formulation of controlled-release baclofen matrix tablets: Influence of some hydrophilic polymers on the release rate and in vitro evaluation

This work aims at investigating different types and levels of hydrophilic matrixing agents, including methylcellulose (MC), sodium alginate (Alg), and sodium carboxymethylcellulose (CMC), in an attempt to formulate controlled-release matrix tablets containing 25 mg baclofen. The tablets were prepared by wet granulation. Prior to compression, the prepared granules were evaluated for flow and compression characteristics. In vitro, newly formulated controlled-release tablets were compared with standard commercial tablets (Lioresal and baclofen). The excipients used in this study did not alter physicochemical properties of the drug, as tested by the thermal analysis using differential scanning calorimetry. The flow and compression characteristics of the prepared granules significantly improved by virtue of granulation process. Also, the prepared matrix tablets showed good mechanical properties (hardness and friability). MC- and Alg-based tablet formulations showed high release-retarding efficiency, and good reproducibility and stability of the drug release profiles when stored for 6 months in ambient room conditions, suggesting that MC and Alg are good candidates for preparing modified-release baclofen tablet formulations.     

Design and study of lamivudine oral controlled release tablets

The objective of this study was to design oral controlled release matrix tablets of lamivudine using hydroxypropyl methylcellulose (HPMC) as the retardant polymer and to study the effect of various formulation factors such as polymer proportion, polymer viscosity, and compression force on the in vitro release of drug. In vitro release studies were performed using US Pharmacopeia type 1 apparatus (basket method) in 900 mL of pH 6.8 phosphate buffer at 100 rpm. The release kinetics were analyzed using the zero-order model equation, Higuchi's square-root equation, and the Ritger-Peppas empirical equation. Compatibility of the drug with various excipients was studied. In vitro release studies revealed that the release rate decreased with increase in polymer proportion and viscosity grade. Increase in compression force was found to decrease the rate of drug release. Matrix tablets containing 60% HPMC 4000 cps were found to show good initial release (26% in first hour) and extended the release up to 16 hours. Matrix tablets containing 80% HPMC 4000 cps and 60% HPMC 15,000 cps showed a first-hour release of 22% but extended the release up to 20 hours. Mathematical analysis of the release kinetics indicated that the nature of drug release from the matrix tablets was dependent on drug diffusion and polymer relaxation and therefore followed non-Fickian or anomalous release. No incompatibility was observed between the drug and excipients used in the formulation of matrix tablets. The developed controlled release matrix tablets of lamivudine, with good initial release (20%-25% in first hour) and extension of release up to 16 to 20 hours, can overcome the disadvantages of conventional tablets of lamivudine.     

Preparation and In-vivo Pharmacokinetic Study of a Novel Extended Release Compression Coated Tablets of Fenoterol Hydrobromide

The aim of this study was to formulate extended release compression coated core tablets of fenoterol hydrobromide, a selective beta(2) adrenergic receptor agonist, in an attempt to prevent nocturnal asthma. Two hydrophilic polymers viz Kollidon SR, Polyox WSR 303 and a hydrophobic one (Precirol ATO5) were employed. Compression coated tablets were formulated by preparing a core tablet containing 7.5 mg drug and various amounts of polymer and Emcompress then compressed coated with the same polymeric materials. For comparison purpose different matrix tablets were also prepared employing the same polymers. In-vitro release studies were carried out at different pH (1.2 and 6.8). Pharmacokinetics of extended release tablets as well as commercially available immediate release tablets (Berotec) were studied after oral administration to beagle dogs using a new developed LC-MS/MS method with a lower limit of quantification of 1 ng/ml. Fenoterol release from compression coated tablets was significantly lower than matrix tablets. The mechanism of release was changed with the nature and content of polymer. The release pattern of drug from F16 containing 40 mg Kollidon SR divided in the core tablet (15 mg) and the rest in the compressed coat (25 mg) showed a typical zero order release kinetic that could extend drug release >10 h and reasonable time for 75% to be released (t(75)) (8.92 h). When compared to immediate release Berotec tablet the MRT was significantly extended from 7.03 +/- 0.76 to 10.93 +/- 1.25 h (P < 0.001) and HVD(t 50%Cmax) was also significantly extended from 2.71 +/- 0.68 to 6.81 +/- 0.67 h with expected prevention of nocturnal asthma.     

Method to recover a lipophilic drug from hydroxypropyl methylcellulose matrix tablets

A reverse-phase high-performance liquid chromatographic (HPLC) method for recovery of the lipophilic drug, alprazolam, from matrix tablets containing the hydrophilic polymer hydroxypropyl methylcellulose (HPMC) was developed. Lipophilic drugs, such as alprazolam, are difficult to completely extract and quantitate from tablets containing HPMC polymer. The percentage of recoveries of alprazolam from placebo powder spiked with alprazolam stock solution and from placebo powder mixed with alprazolam powder were about 100% and 85% to 95%, respectively. The validated method using water to completely dissolve HPMC before the addition of a strong solvent to dissolve and extract the drug from the HPMC solution was shown to be the most reproducible method. Different molecular weight distributions of the HPMC polymer, such as HPMC-K4M and HPMC-K100LV, did not influence the dissolution results of alprazolam using this validated method. Similarly, the excipients composing the matrix tablet formulations, such as dicalcium phosphate dihydrate, dicalcium phosphate anhydrous, calcium sulfate dihydrate, sucrose, dextrose, and lactose monohydrate, did not influence the percent recovery of alprazolam. The recovery method reported herein was shown to be the most efficient to achieve complete recovery of alprazolam from powder blends and tablets containing a variety of excipients and different grades of HPMC.     

Colon Specific Delivery of Indomethacin: Effect of Incorporating pH Sensitive Polymers in Xanthan Gum Matrix Bases

In the present study, an attempt has been made to design controlled release colon-specific formulations of indomethacin by employing pH responsive polymers Eudragit (L100 or S100) in matrix bases comprised of xanthan gum. The prepared tablets were found to be of acceptable quality with low-weight variation and uniform drug content. In vitro release studies indicated rapid swelling and release of significant percentage of drug in the initial period from matrix tablets composed of xanthan gum alone. Addition of pH responsive polymers Eudragit (L100 or S100) to xanthan gum matrix resulted in negligible to very low drug release in the initial period in acidic to weakly acidic medium. Furthermore, with increase in pH of the dissolution medium due to dissolution of Eudragit L100/Eudragit S100 that resulted in the formation of a porous matrix, faster but controlled drug release pattern was observed. Thus, a sigmoidal release pattern was observed from the designed formulations suitable for colonic delivery. Drug release mechanism in all cases was found to be of super case II type, indicating erosion to be the primary cause of drug release. Since the drug release from almost all the matrix bases in the initial phase was negligibly low and followed with controlled release for about 14–16 h, it was concluded that a matrix design of this composition could have potential applications as a colon-specific drug delivery device with additional advantage of easy scale-up and avoidance of all-or-none phenomenon associated with coated colon-specific systems.     

Comparison of Release-Controlling Efficiency of Polymeric Coating Materials Using Matrix-type Casted Films and Diffusion-Controlled Coated Tablet

Polymeric coating materials have been widely used to modify release rate of drug. We compared physical properties and release-controlling efficiency of polymeric coating materials using matrix-type casted film and diffusion-controlled coated tablet. Hydroxypropylmethyl cellulose (HPMC) with low or high viscosity grade, ethylcellulose (EC) and Eudragit® RS100 as pH-independent polymers and Eudragit S100 for enteric coatings were chosen to prepare the casted film and coated tablet. Tensile strength and contact angle of matrix-type casted film were invariably in the decreasing order: EC> Eudragit S100> HPMC 100000> Eudragit RS100>HPMC 4000. There was a strong linear correlation between tensile strength and contact angle of the casted films. In contrast, weight loss (film solubility) of the matrix-type casted films in three release media (gastric, intestinal fluid and water) was invariably in the increasing order: EC < HPMC 100000 < Eudragit RS100 < HPMC 4000 with an exception of Eudragit S100. The order of release rate of matrix-type casted films was EC > HPMC 100000 > Eudragit RS100 > HPMC 4000 > Eudragit S100. Interestingly, diffusion-controlled coated tablet also followed this rank order except Eudragit S100 although release profiles and lag time were highly dependent on the coating levels and type of polymeric coating materials. EC and Eudragit RS100 produced sustained release while HPMC and Eudragit S100 produced pulsed release. No molecular interactions occurred between drug and coating materials using ¹H-NMR analysis. The current information on release-controlling power of five different coating materials as matrix carrier or diffusion-controlled film could be applicable in designing oral sustained drug delivery.Key words: diffusion-controlled coated tablet, drug release rate, matrix-type casted film, polymeric coating materials, release-controlling power     

Evaluation of alginate compressed matrices as prolonged drug delivery systems

This research investigated the use of sodium alginate for the preparation of hydrophylic matrix tablets intended for prolonged drug release using ketoprofen as a model drug. The matrix tablets were prepared by direct compression using sodium alginate, calcium gluconate, and hydroxypropylmethylcellulose (HPMC) in different combinations and ratios. In vitro release tests and erosion studies of the matrix tablets were carried out in USP phosphate buffer (pH 7.4). Matrices consisting of sodium alginate alone or in combination with 10% and 20% of HPMC give a prolonged drug release at a fairly constant rate. Incorporation of different ratios of calcium gluconate leads to an enhancement of the release rate from the matrices and to the loss of the constant release rate of the drug. Only the matrices containing the highest quantity of HPMC (20%) maintained their capacity to release ketoprofen for a prolonged time.     

Rheological Characterization and Drug Release Studies of Gum Exudates of Terminalia catappa Linn

The present study was undertaken to evaluate the gum exudates of Terminalia catappa Linn. (TC gum) as a release retarding excipient in oral controlled drug delivery system. The rheological properties of TC gum were studied and different formulation techniques were used to evaluate the comparative drug release characteristics. The viscosity was found to be dependent on concentration and pH. Temperature up to 60°C did not show significant effect on viscosity. The rheological kinetics evaluated by power law, revealed the shear thinning behavior of the TC gum dispersion in water. Matrix tablets of TC gum were prepared with the model drug dextromethorphan hydrobromide (DH) by direct compression, wet granulation and solid dispersion techniques. The dissolution profiles of the matrix tablets were compared with the pure drug containing capsules using the USP Basket apparatus with 500 ml phosphate buffer of pH 6.8 as a dissolution medium. The drug release from the compressed tablets containing TC gum was comparatively sustained than pure drug containing capsules. Even though all the formulation techniques showed reduction of dissolution rate, aqueous wet granulation showed the maximum sustained release of more than 8 h. The release kinetics estimated by the power law revealed that the drug release mechanism involved in the dextromethorphan matrix is anomalous transport as indicated by the release exponent n values. Thus the study confirmed that the TC gum might be used in the controlled drug delivery system as a release-retarding polymer.     

Influence of ibuprofen as a solid-state plasticizer in eudragit® RS 30 D on the physicochemical properties of coated beads

The purpose of this study was to investigate the physicochemical properties of nonpareil beads coated with Eudragit RS 30 D containing ibuprofen as a multifunctional agent. The influence of the concentration of ibuprofen in the film coating and the effect of the coating level on drug release from coated beads was determined in pH 7.2 phosphate buffer solution. The influence of storage time at 23 degrees C and 60 degrees C on the release of ibuprofen from coated beads was also investigated. The thermal properties of the films were determined using a differential scanning calorimeter. Scanning electron microscopy was employed to image the surface morphology of the coated beads. Infrared spectroscopy was used to study the interaction of Eudragit RS 30 D and ibuprofen. Results from the dissolution studies demonstrated that increasing the amount of ibuprofen in the polymeric film reduced the rate of drug release, mainly because of a more complete coalescence of the polymeric particles of the latex dispersion. The glass transition temperature (Tg) of Eudragit RS 30 D films decreased and the surface of the coated beads became smoother as the concentration of ibuprofen was increased. Hydrogen bonding between the polymer and ibuprofen was demonstrated by Fourier transform infrared spectroscopy. No significant differences were found in drug dissolution between the coated beads stored at 23 degrees C for 12 months and those stored at 60 degrees C for 12 hours. The results of this study demonstrated that the ibuprofen plasticized the Eudragit RS 30 D. Furthermore, the dissolution rate of ibuprofen can be controlled and changes in the drug release rate can be minimized by using the drug-induced plasticization technique with this polymer.     

Effect of degree of esterification of pectin and calcium amount on drug release from pectin-based matrix tablets

The aim of this work was to assess the effect of 2 formulation variables, the pectin type (with different degrees of esterification [DEs]) and the amount of calcium, on drug release from pectin-based matrix tablets. Pectin matrix tablets were prepared by blending indomethacin (a model drug), pectin powder, and various amounts of calcium acetate and then tableting by automatic hydraulic press machine. Differential scanning calorimetry, powder x-ray diffraction, and Fourier transformed-infrared spectroscopy studies of the compressed tablets revealed no drug-polymer interaction and the existence of drug with low crystallinity. The in-vitro release studies in phosphate buffer (United States Pharmacopeia) and tris buffer indicated that the lower the DE, the greater the time for 50% of drug release (T₅₀). This finding is probably because of the increased binding capacity of pectin to calcium. However, when the calcium was excluded, the pectins with different DEs showed similar release pattern with insignificant difference of T₅₀. When the amount of calcium acetate was increased from 0 to 12 mg/tablet, the drug release was significantly slower. However, a large amount of added calcium (ie, 24 mg/tablet) produced greater drug release because of the partial disintegration of tablets. The results were more pronounced in phosphate buffer, where the phosphate ions induced the precipitation of calcium phosphate. In conclusion, both pectin type and added calcium affect the drug release from the pectin-based matrix tablets.     

Preparation and Evaluation of Sustained-Release Matrix Tablets Based on Metoprolol and an Acrylic Carrier Using Injection Moulding

Sustained-release matrix tablets based on Eudragit RL and RS were manufactured by injection moulding. The influence of process temperature; matrix composition; drug load, plasticizer level; and salt form of metoprolol: tartrate (MPT), fumarate (MPF) and succinate (MPS) on ease of processing and drug release were evaluated. Formulations composed of 70/30% Eudragit RL/MPT showed the fastest drug release, substituting part of Eudragit RL by RS resulted in slower drug release, all following first-order release kinetics. Drug load only affected drug release of matrices composed of Eudragit RS: a higher MPT concentration yielded faster release rates. Adding triethyl citrate enhanced the processability, but was detrimental to long-term stability. The process temperature and plasticizer level had no effect on drug release, whereas metoprolol salt form significantly influenced release properties. The moulded tablets had a low porosity and a smooth surface morphology. A plasticizing effect of MPT, MPS and MPF on Eudragit RS and Eudragit RL was observed via DSC and DMA. Solubility parameter assessment, thermal analysis and X-ray diffraction demonstrated the formation of a solid solution immediately after production, in which H-bonds were formed between metoprolol and Eudragit as evidenced by near-infrared spectroscopy. However, high drug loadings of MPS and MPF showed a tendency to recrystallise during storage. The in vivo performance of injection-moulded tablets was strongly dependent upon drug loading.     

Effect of Different Excipients on the Physical Characteristics of Granules and Tablets with Carbamazepine Prepared with Polyethylene Glycol 6000 by Fluidized Hot-Melt Granulation (FHMG)

The objective of this study was to investigate the properties of granules and tablets with carbamazepine which were prepared employing a fluidized hot-melt granulation (FHMG) technique. The FHMG process was carried out at 65°C. Macrogol 6000 (PEG 6000) was used as a binder at the content 10% (w/w) of the granulated mass. Granules containing up to 70% (w/w) of the drug and 20–90% (w/w) of a filler (lactose, mannitol, calcium hydrogen phosphate (Di-Cafos), pregelatinized starch, and microcrystalline cellulose (MCC)) were produced. When the drug content was 30% (w/w), the yield of the process was satisfying (>95%) and flowability of the granules was better than placebo granules or drug-loaded granules prepared by wet granulation. Type of a filler had strong impact on physical properties of granules, and size distribution of the particles was the most homogenous when lactose or Di-Cafos were used. The FHMG technique enabled preparation of granules with better compressability compared with the wet-granulated product or with non-granulated powders. Tablets with shorter disintegration time than 10 min were obtained with 2.0% crospovidone added as a disintegrant. In comparison to tablets prepared from the wet-granulated mass, employment of the FHMG method resulted in tablets with faster dissolution of carbamazepine (more than 80% of the drug released within 15 min). This was achieved with mannitol or lactose/MCC, as fillers.     

A novel approach in the assessment of polymeric film formation and film adhesion on different pharmaceutical solid substrates

The purpose of this study was to evaluate the nature of film formation on tablets with different compositions, using confocal laser scanning microscopy (CLSM), and to measure film adhesion via the application of a novel “magnet probe test”. Three excipients, microcrystalline cellulose (MCC), spray-dried lactose monohydrate, and dibasic calcium phosphate dihydrate, were individually blended with 0.5% magnesium stearate, as a lubricant, and 2.5% tetracycline HCl, as a fluorescent marker, and were compressed using a Carver press. Tablets were coated with a solution consisting of 7% hydroxypropyl methylcellulose (HPMC) phthalate (HP-55), and 0.5% cetyl alcohl in acetone and isopropanol (11:9). The nature of polymer interaction with the tablets and coating was evaluated using CLSM and a designed magnet probe test. CLSM images clearly showed coating efficiency, thickness, and uniformity of film formation, and the extent of drug migration into the film at the coating interfaces of tablets. Among the excipients, MCC demonstrated the best interface for both film formation and uniformity in thickness relative to lactose monohydrate and dibasic calcium phosphate dihydrate. The detachment force of the coating layers from the tablet surfaces, as measured with the developed magnet probe test, was in the order of MCC>lactose monohydrate>dibasic calcium phosphate dihydrate. It was also shown that the designed magnet probe test provides reliable and reproducible results when used for measurement of film adhesion and bonding strength.