Protein resistance of dextran and dextran-poly(ethylene glycol) copolymer films

The protein resistance of dextran and dextran-poly(ethylene glycol) (PEG) copolymer films was examined on an organosilica particle-based assay support. Comb-branched dextran-PEG copolymer films were synthesized in a two step process using the organosilica particle as a solid synthetic support. Particles modified with increasing amounts (0.1–1.2 mg m^?2) of three molecular weights (10,000, 66,900, 400,000 g mol^?1) of dextran were found to form relatively poor protein-resistant films compared to dextran-PEG copolymers and previously studied PEG films. The efficacy of the antifouling polymer films was found to be dependent on the grafted amount and its composition, with PEG layers being the most efficient, followed by dextran-PEG copolymers, and dextran alone being the least efficient. Immunoglobulin gamma (IgG) adsorption decreased from ～5 to 0.5 mg m^?2 with increasing amounts of grafted dextran, but bovine serum albumin (BSA) adsorption increased above monolayer coverage (～2 mg m^?2) indicating ternary adsorption of the smaller protein within the dextran layer.     

Particle-by-particle quantification of protein adsorption onto poly(ethylene glycol) grafted surfaces

The use and advantage of flow cytometry as a particle-by-particle, low sampling volume, high-throughput screening technique for quantitatively examining the non-specific adsorption of proteins onto surfaces is presented. The adsorption of three proteins: bovine serum albumin (BSA), immunoglobulin gamma (IgG) and protein G, incubated at room temperature for 2 h onto organosilica particles modified with poly(ethylene glycol) (PEG) of increasing MW (2000, 3400, 6000, 10,000 and 20,000 g mol(-1)) and grafted amounts (0.14-1.4 mg m(-2)) was investigated as a model system. Each protein exhibited Langmuir-like, high affinity monolayer limited adsorption on unmodified particles with the proteins reaching surface saturation at 1.8, 4.0 and 2.5 mg m(-2) for BSA, IgG and protein G, respectively. Protein adsorption on PEG-modified surfaces was found to decrease with increasing amounts of grafted polymer. PEG grafting amounts >0.6 mg m(-2) effectively prevented the adsorption of the larger two proteins (BSA and IgG) while a PEG grafting amount >1.3 mg m(-2) was required to prevent the adsorption of the smaller protein G.     

Drug release from and hydrolytic degradation of a poly(ethylene glycol) grafted poly(3-hydroxyoctanoate)

Monoacrylate-poly(ethylene glycol)-grafted poly(3-hydroxyoctanoate) (PEGMA-g-PHO) copolymers were synthesized to develop a swelling-controlled release delivery system for ibuprofen as a model drug. The in vitro hydrolytic degradation of and the drug release from a film made of the PEGMA-g-PHO copolymer were carried out in a phosphate buffer saline (pH 7.4) medium. The hydrolytic degradation of the copolymer was strongly dependent on the degree of grafting (DG) of the PEGMA group. The degradation rate of the copolymer films in vitro increased with increasing DG of the PEGMA group on the PHO chain. The copolymer films showed a controlled delivery of ibuprofen to the medium in periods of time that depend on the composition, hydrophilic/hydrophobic characteristics, initial drug loading amount and film thickness of the graft copolymer support. The drug release rate from the grafted copolymer films was faster than the rate of weight loss of the films themselves. In particular, a combination of the low DG of the PEGMA group in the PHO chains with the low ibuprofen solubility in water led to long-term constant release from these matrices in vitro.     

Polyethylenimine-graft-poly(ethylene glycol) copolymers: influence of copolymer block structure on DNA complexation and biological activities as gene delivery system

For two series of polyethylenimine-graft-poly(ethylene glycol) (PEI-g-PEG) block copolymers, the influence of copolymer structure on DNA complexation was investigated and physicochemical properties of these complexes were compared with the results of blood compatibility, cytotoxicity, and transfection activity assays. In the first series, PEI (25 kDa) was grafted to different degrees of substitution with PEG (5 kDa) and in the second series the molecular weight (MW) of PEG was varied (550 Da to 20 kDa). Using atomic force microscopy, we found that the copolymer block structure strongly influenced the DNA complex size and morphology: PEG 5 kDa significantly reduced the diameter of the spherical complexes from 142 +/- 59 to 61 +/- 28 nm. With increasing degree of PEG grafting, complexation of DNA was impeded and complexes lost their spherical shape. Copolymers with PEG 20 kDa yielded small, compact complexes with DNA (51 +/- 23 nm) whereas copolymers with PEG 550 Da resulted in large and diffuse structures (130 +/- 60 nm). The zeta-potential of complexes was reduced with increasing degree of PEG grafting if MW >or= 5 kDa. PEG 550 Da did not shield positive charges of PEI sufficiently leading to hemolysis and erythrocyte aggregation. Cytotoxicity (lactate dehydrogenase assay) was independent of MW of PEG but affected by the degree of PEG substitution: all copolymers with more than six PEG blocks formed DNA complexes of low toxicity. Finally, transfection efficiency of the complexes was studied. The combination of large particles, low toxicity, and high positive surface charge as in the case of copolymers with many PEG 550 Da blocks proved to be most efficient for in vitro gene transfer. To conclude, the degree of PEGylation and the MW of PEG were found to strongly influence DNA condensation of PEI and therefore also affect the biological activity of the PEI-g-PEG/DNA complexes. These results provide a basis for the rational design of block copolymer gene delivery systems.     

RGD-grafted poly-L-lysine-graft-(polyethylene glycol) copolymers block non-specific protein adsorption while promoting cell adhesion

A novel class of surface-active copolymers is described, designed to protect surfaces from nonspecific protein adsorption while still inducing specific cell attachment and spreading. A graft copolymer was synthesized, containing poly-(L-lysine) (PLL) as the backbone and substrate binding and poly(ethylene glycol) (PEG) as protein adsorption-resistant pendant side chains. A fraction of the grafted PEG was pendantly functionalized by covalent conjugation to the peptide motif RGD to induce cell binding. The graft copolymer spontaneously adsorbs from dilute aqueous solution onto negatively charged surfaces. The performance of RGD-modified PLL-g-PEG copolymers was analyzed in protein adsorption and cell culture assays. These coatings efficiently blocked the adsorption of serum proteins to Nb(2)O(5) and tissue culture polystyrene while specifically supporting attachment and spreading of human dermal fibroblasts. This surface functionalization technology is expected to be valuable in both the biomaterial and biosensor fields, because different signals can easily be combined, and sterilization and application are straightforward and cost-effective.     

Physicochemical and biological characterization of polyethylenimine-graft-poly(ethylene glycol) block copolymers as a delivery system for oligonucleotides and ribozymes

Two different series of polyethylenimine (PEI) block copolymers grafted with linear poly(ethylene glycol) (PEG) were investigated as delivery systems for oligodeoxynucleotides (ODN) and ribozymes. The resulting interpolyelectrolyte complexes were characterized with respect to their physicochemical properties, protection efficiency against enzymatic degradation, complement activation, and biological activity under in vitro conditions. The effect of PEG molecular weight and the graft density of PEG blocks on complex characteristics was studied with two different series of block copolymers. The resulting ODN complexes were characterized by photon correlation spectroscopy (PCS) and laser Doppler anemometry (LDA) to determine complex size and zeta potential. Electrophoresis was performed to study the protective effects of the different block copolymers against enzymatic degradation of ODN. Intact ODN was quantified via densitometric analysis. Ribozymes, a particularly unstable type of oligonucleotides, were used to examine the influence of block copolymer structure on biological activity. The stabilization of ribozymes was also characterized in a cell culture model. Within the first series of block copolymers, the grafted PEG chains (5 kDa) had marginal influence on the complex size. Two grafted PEG chains were sufficient to achieve a neutral zeta potential. Within the second series, size and zeta potential increased with an increasing number of PEG chains. A high number of short PEG chains resulted in a decrease in complex size to values comparable to that of the homopolymer PEI 25 kDa and a neutral zeta potential, indicating a complete shielding of the charges. Complement activation decreased with an increasing number of short PEG 550 Da chains. Ribozyme complexes with PEG-PEI block copolymers achieved a 50% down-regulation of the target mRNA. This effect demonstrated an efficient stabilization and biological activity of the ribozyme, which was comparable to that of PEI 25 kDa. PEGylated PEI block copolymers represent a promising new class of drug delivery systems for ODN and ribozymes with increased biocompatibility and physical stability.     

Synthesis and solution behavior of poly(ε-caprolactone) grafted hydroxyethyl cellulose copolymers

Trimethylsilylated hydroxyethyl cellulose (TMSHEC) was synthesized by using hexamethyldisilazane (HMDS) as silylated agent. With the partial protection of hydroxyl groups of HEC by silylation, the novel poly(?-polycaprolactone) (PCL) grafted HEC (HEC-g-PCL) copolymers were successfully prepared by homogenous ring-opening graft polymerization and deprotection procedure. The structure of HEC-g-PCL copolymers was characterized by FTIR and 1H NMR. Fluorescence spectrum of HEC-g-PCL copolymer dilute solution indicated that copolymers could associate and form hydrophobic microdomains in aqueous solution. With the increasing of grafted PCL content, the critical association concentration (cac) of HEC-g-PCL copolymers decreased. The surface tension of HEC-g-PCL copolymers decreased dramatically with the increasing of the concentration and then approached to a plateau value when concentration was above the cac of HEC-g-PCL copolymers. The hydrodynamic radius of the aggregate of copolymer in dilute solution was found to increase with the increasing of the grafted PCL content. When the concentration of copolymer was above the cac, the zero-shear viscosity of the copolymer increased sharply and became much higher than that of HEC at the same concentration.     

Synthesis, characterization, and morphology studies of biodegradable amphiphilic poly[(R)-3-hydroxybutyrate]-alt-poly(ethylene glycol) multiblock copolymers

Novel biodegradable amphiphilic alternating block copolymers based on poly[(R)-3-hydroxybutyrate] (PHB) as biodegradable and hydrophobic block and poly(ethylene glycol) (PEG) as hydrophilic block (PHB-alt-PEG) were successfully synthesized through coupling reaction. Their chemical structures have been characterized by using gel permeation chromatography, (1)H nuclear magnetic resonance, and Fourier transform infrared spectroscopy. Differential scanning calorimetry (DSC) analysis revealed that both PHB and PEG blocks in PHB-alt-PEG block copolymers can crystallize to form separate crystalline phase except in those with a short PEG block (M(n) 600) only PHB crystalline phase has been observed. However, due to the mutual interference from each other, the melting transition of both PHB and PEG crystalline phases shifted to lower temperature with lower crystallinity in comparison with corresponding pure PHB and PEG. The crystallization behavior of PHB block and PEG block has also been studied by X-ray diffraction, and the results were in good agreement with those deduced from DSC study. The surface morphologies of PHB-alt-PEG block copolymer thin films spin-coated on mica have been visualized by atomic force microscopy with tapping mode, indicating formation of laterally regular lamellar surface patterns. Static water contact angle measurement revealed that surface hydrophilicity of these spin-coated thin films increases with increasing PEG block content.     

Investigation of polymer and nanoparticle properties with nicotinic acid and p-aminobenzoic acid grafted on poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) via click chemistry

In this study, the grafting of nicotinic acid and p-aminobenzoic acid (PABA) onto poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) was performed by Huisgen's 1,3-dipolar cycloaddition, also known as click chemistry. Concentrations used for grafting were 0.10, 0.20, and 0.30 molar ratios with respect to caproyl units. The grafted copolymers were successfully obtained at all ratios as confirmed by NMR, GPC, and FT-IR. According to the DSC results, the polymorphisms of these grafted copolymers were mostly changed from semicrystalline to amorphous depending on the type and the amount of grafting compounds. TGA thermograms showed different thermal stabilities of the grafted copolymers compared to the original copolymers. Cytotoxicity results from HUVEC models suggested that the toxicity of grafted nanoparticles increased with the molar ratios of grafting units. Due to differences in molecular structure between nicotinic acid and PABA, physicochemical properties (particle size and surface charge) of grafted copolymer nanoparticles were substantially different. With increasing molar ratio of the grafting units, the particle size of blank nanoparticles tended to increase, resulting from an increase in the hydrophobic fragments of the grafted copolymer. Ibuprofen was chosen as a model drug to evaluate the interaction between grafted copolymers and loaded drug. After ibuprofen loading, the particle size of the loaded nanoparticles of both grafted copolymers increased compared to that of the blank nanoparticles. Significant differences in loading capacity between nicotinic acid and PABA grafted copolymer nanoparticles were clearly shown. This is most likely a result of different compatibility between each grafting compound and ibuprofen, including hydrogen bond interaction, π-π stacking interaction, and steric hindrance.     

Synthesis and characterization of hydroxypropyl methylcellulose and ethyl acrylate graft copolymers

The synthesis of hydroxypropyl methylcellulose-g-poly (ethyl acrylate) was carried out by potassium persulfate induced graft copolymerization in homogeneous aqueous medium. By varying the reaction conditions, graft copolymers with different percentage of grafting were prepared. These graft copolymers were characterized by fourier transform infrared spectra (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermogravimetric analyses (TGA), X-ray diffraction analysis (XRD), and dynamic light scattering (DLS) methods. The molecular weight of grafted and ungrafted polymer chains determined by gel permeation chromatography (GPC) increased with increasing monomer and matrix concentration but decreased with increasing initiator concentration and reaction temperature. The mechanical properties of graft copolymers were measured as function of the percentage of grafting. In addition, the equilibrium humidity adsorption behavior and the disintegration time of the grafted copolymer films were also studied.     

Morphological control of poly(ethylene glycol)-block-poly(epsilon-caprolactone) copolymer aggregates in aqueous solution

In aqueous solution, it was found that the amphiphilic copolymer poly(ethylene glycol)-b-poly(caprolactone) (PEG(5000)-b-PCL(4100)) formed different morphologies, including long rod-like, short rod-like, or spherical aggregates, when the copolymer concentration was increased. Nearly identical morphologies were observed with the addition of increasing amounts of PEG(2000)-distearoylphosphoethanolamine (PEG(2000)-DSPE) to the copolymer. The morphologies of the aggregates in solution were confirmed by negative stain transmission electron microscopy (TEM) and cryogenic-TEM (cryo-TEM). The critical micelle concentrations of the PEG(5000)-b-PCL(4100) copolymer, PEG(2000)-DSPE and a mixture of the two materials (PEG(5000)-b-PCL 4100/PEG(2000)-DSPE) were evaluated to determine the thermodynamic stability of the aggregates. Differential scanning calorimetry was performed to gain insight into the degree of mixing of PEG(5000)-b-PCL(4100) and PEG(2000)-DSPE. Overall, combining PEG(5000)-b-PCL(4100) and PEG(2000)-DSPE produced a single population of mixed micelles with rod-like or spherical morphologies depending on the material composition and concentration.     

Interaction of poly(L-lysine)-g-poly(ethylene glycol) with supported phospholipid bilayers

Interactions between the graft copolymer poly(L-lysine)-g-poly(ethylene glycol), PLL-g-PEG, and two kinds of surface-supported lipidic systems (supported phospholipid bilayers and supported vesicular layers) were investigated by a combination of microscopic and spectroscopic techniques. It was found that the application of the copolymer to zwitterionic or negatively charged supported bilayers in a buffer of low ionic strength led to their decomposition, with the resulting formation of free copolymer-lipid complexes. The same copolymer had no destructive effect on a supported vesicular layer made up of vesicles of identical composition. A comparison between poly(L-lysine), which did not induce decomposition of supported bilayers, and PLL-g-PEG copolymers with various amounts of PEG side chains per backbone lysine unit, suggested that steric repulsion between the PEG chains that developed upon adsorption of the polymer to the nearly planar surface of a supported phospholipid bilayer (SPB) was one of the factors responsible for the destruction of the SPBs by the copolymer. Other factors included the ionic strength of the buffer used and the quality of the bilayers, pointing toward the important role defects present in the SPBs play in the decomposition process.     

Synthesis and self-assembly of well-defined poly(amino acid) end-capped poly(ethylene glycol) and poly(2-methyl-2-oxazoline)

Poly(ethylene glycol) (PEG) and poly(2-methyl-2-oxazoline) (PMOx) are water-soluble, biocompatible polymers with stealth hemolytic activities. Poly(amino acid) (PAA) end-capped PEG and PMOx were prepared using amino-terminated derivatives of PEG and PMOx as macroinitiators for the ring-opening polymerization of γ-benzyl protected l-glutamate N-carboxyanhydride and S-benzyloxycarbonyl protected l-cysteine N-carboxyanhydride, respectively, in the presence of urea, at room temperature. The molecular weight of the PAA moiety was kept between M(n) = 2200 and 3000 g mol(-1). PMOx was polymerized by cationic ring-opening polymerization resulting in molecular weights of M(n) = 5000 and 10,000 g mol(-1), and PEG was a commercial product with M(n) = 5000 g mol(-1). Here, we investigate the self-assembly of the resulting amphiphilic block copolymers in water and the effect of the chemical structure of the block copolymers on the solution properties of self-assembled nanostructures. The PEG-block-poly(amino acid), PEG-b-PAA, and PMOx-block-poly(amino acid), PMOx-b-PAA, block copolymers have a narrow and monomodal molecular weight distribution (PDI < 1.3). Their self-assembly in water was studied by dynamic light scattering and fluorescence spectroscopy. In aqueous solution, the block copolymers associate into particles with hydrodynamic radii (R(H)) ranging in size from R(H) 70 to 130 nm, depending on the block copolymer architecture and the polymer molecular weight. Larger R(H) and critical association concentration values were obtained for copolymers containing poly(S-benzyloxycarbonyl-l-cysteine) compared to their poly(γ-benzyl-L-glutamate) analogue. FTIR investigations revealed that the poly(γ-benzyl-L-glutamate) block adopts a helical conformation, while the poly(S-benzyloxycarbonyl-L-cysteine) block exists as β-sheet.     

Polymer-oligonucleotide conjugate synthesis from an amphiphilic block copolymer. Applications to DNA detection on microarray

An amphiphilic block copolymer poly(tert-butylacrylamide-b-(N-acryloylmorpholine-N-acryloxysuccinimide)) (poly(TBAm-b-(NAM/NAS)) and a random copolymer poly(NAM/NAS), synthesized by the reversible addition-fragmentation chain transfer (RAFT) polymerization process, have been used as support for oligonucleotide (ODN) synthesis, to elaborate polymer-oligonucleotide conjugates. In a first step, starters of ODN solid-phase synthesis were coupled to activated ester functions of polymers, and second, resulting functionalized polymers were covalently grafted onto hydroxylated controlled pore glass (CPG) support to further accomplish ODN synthesis. An efficient capping of residual hydroxyl functions of CPG was performed before synthesis, with both acetic anhydride and diethoxy-N,N-diisopropyl-phosphoramidite reagents, to suppress parasite-free ODN population present in conjugate crude material and resulting from syntheses directly initiated on silica beads. After purification, conjugates were evaluated in a DNA hybridization assay on a microarray, as macromolecules being able to favor capture of the target. Conjugate coating conditions were studied on the dT25/dA25 model. The role of the hydrophobic part (poly(TBAm)) of the conjugate synthesized with the block copolymer in the orientation of the conjugate after coating was revealed by spotting experiments achieved in a mixed solvent (DMF/H(2)O). The use of block copolymer-dT25 conjugate afforded a significant sensitivity improvement of the hybridization assay.     

Multifunctional poly(ethylene glycol) semi-interpenetrating polymer networks as highly selective adhesive substrates for bioadhesive peptide grafting

Novel artificial extracellular matrices were synthesized in the form of semi-interpenetrating polymer networks containing copolymers of poly(ethylene glycol) and acrylic acid (PEG-co-AA) grafted with synthetic bioadhesive peptides onto exposed carboxylic acid moieties. These substrates were very resistant to cell adhesion, but when they were grafted with adhesive peptides they were highly biospecific in their ability to support cell adhesion. Extensive preadsorption of adhesive proteins or peptides did not render these materials cell adhesive; yet covalent grafting of adhesive peptides did render these materials highly cell adhesive even in the absence of serum proteins. Polymer networks containing immobilized PEG-co-AA were grafted with peptides at densities of 475 +/- 40 pmol/cm(2). Polymer networks containing immobilized PEG-co-AA N-terminally grafted with GRGDS supported cell adhesion efficiencies of 42 +/- 4% 4 h after seeding and became confluent after 12 h. These cells displayed cell spreading and cytoskeletal grafted with inactive control peptides (GRDGS, GRGES, or no peptide) supported cell adhesion efficiencies of 0 +/- 0%, even when challenged with high seeding densities (to 100,000 cell/cm(2)) over 14 days. These polymer networks are suitable substrates to investigate in vitro cell-surface interactions in the presence of serum proteins without nonspecific protein adsorption adhesion signals other than those immobilized for study.     

Surface modification with poly(sulfobetaine methacrylate-co-acrylic acid) to reduce fibrinogen adsorption, platelet adhesion, and plasma coagulation

Zwitterionic sulfobetaine methacrylate (SBMA) polymers were known to possess excellent antifouling properties due to high hydration capacity and neutral charge surface. In this study, copolymers of SBMA and acrylic acid (AA) with a variety of compositions were synthesized and were immobilized onto polymeric substrates with layer-by-layer polyelectrolyte films via electrostatic interaction. The amounts of platelet adhesion and fibrinogen adsorption were determined to evaluate hemocompatibility of poly(SBMA-co-AA)-modified substrates. Among various deposition conditions by modulating SBMA ratio in the copolymers and pH of the deposition solution, poly(SBMA(56)-co-AA(44)) deposited at pH 3.0 possessed the best hemocompatibility. This work demonstrated that poly(SBMA-co-AA) copolymers adsorbed on polyelectrolyte-base films via electrostatic interaction improve hemocompatibility effectively and are applicable for various substrates including TCPS, PU, and PDMS. Furthermore, poly(SBMA-co-AA)-coated substrate possesses great durability under rigorous conditions. The preliminary hemocompatibility tests regarding platelet adhesion, fibrinogen adsorption, and plasma coagulation suggest the potential of this technique for the application to blood-contacting biomedical devices.     

Poly(ethylene glycol-co-allyl glycidyl ether)s: a PEG-based modular synthetic platform for multiple bioconjugation

A series of random copolymers comprising ethylene oxide (EO) and 0-100% allyl glycidyl ether (AGE) has been prepared by anionic ring-opening polymerization with molecular weights between 5000 and 13,600 g/mol and polydispersity indices in the range of 1.04-1.19. As key for the homogeneity of the PEG conjugates, real-time 1H NMR polymerization kinetics, 13C NMR analysis of triad sequence distribution, and analysis of the thermal behavior by differential scanning calorimetry (DSC) revealed a distinctive random copolymer structure. Via thiol-ene coupling (TEC), showing mainly "click" characteristics and nearly quantitative yields, PEG derivatives with multiple amino, carboxy, or hydroxy functionalities have been prepared, providing suitable reactivities for further attachment. Without further modification, P(EO-co-AGE)s were conjugated with cysteine or the tripeptide glutathione (GSH) via TEC, resulting in well-defined hybrid materials with multiple peptide units conjugated to the PEG backbone. The results demonstrate superior loading capacity of the copolymers in comparison to the PEG homopolymer.     

Synthesis and characterization of RGD peptide grafted poly(ethylene glycol)-b-poly(L-lactide)-b-poly(L-glutamic acid) triblock copolymer

Advances in tissue engineering require biofunctional scaffolds that can provide not only physical support for cells but also chemical and biological cues needed in forming functional tissues. To achieve this goal, a novel RGD peptide grafted poly(ethylene glycol)-b-poly(L-lactide)-b-poly(L-glutamic acid) (PEG-PLA-PGL/RGD) was synthesized in four steps (1) to prepare diblock copolymer PEG-PLA-OH and to convert its -OH end group into -NH(2) (to obtain PEG-PLA-NH(2)), (2) to prepare triblock copolymer PEG-PLA-PBGL by ring-opening polymerization of NCA (N-carboxyanhydride) derived from benzyl glutamate with diblock copolymer PEG-PLA-NH(2) as macroinitiator, (3) to remove the protective benzyl groups by catalytic hydrogenation of PEG-PLA-PBGL to obtain PEG-PLA-PGL, and (4) to react RGD (arginine-glycine-(aspartic amide)) with the carboxyl groups of the PEG-PLA-PGL. The structures of PEG-PLA-PGL/RGD and its precursors were confirmed by (1)H NMR, FT-IR, amino acid analysis, and XPS analysis. Addition of 5 wt % PEG-PLA-PGL/RGD into a PLGA matrix significantly improved the surface wettability of the blend films and the adhesion and proliferation behavior of human chondrocytes and 3T3 cells on the blend films. Therefore, the novel RGD-grafted triblock copolymer is expected to find application in cell or tissue engineering.     

Protein sorption and recovery by hydrogels using principles of aqueous two-phase extraction

Use of the thermodynamic principles of aqueous two-phase extraction (ATPE) to drive protein into a crosslinked gel is developed as a protein isolation and separation technique, and as a protein loading technique for drug delivery applications. A PEG/dextran gel system was chosen as a model system because PEG/dextran systems are widely used in aqueous two-phase extraction and dextran gels (Sephadex(R)) are common chromatographic media. The effects of polymer concentrations and molecular weights, salts, and pH on the partitioning of ovalbumin matched ATPE heuristics and data trends. Gel partition coefficients (Cgel/Csolution) increased with increasing PEG molecular weight and concentration and decreasing dextran concentration (increased gel swelling). The addition of PEG to the buffer solution yielded partition coefficients more than an order of magnitude greater than those obtained in systems with buffer alone, or added salt. A combined salt/PEG system yielded an additional order of magnitude increase. For example, when ovalbumin solution (2.3 mg/mL) was equilibrated with Sephadex(R) G-50 at pH 6.75, the partition coefficients were 0.13 in buffer, 0.11 in buffer with 0.22M KI, 2.3 in 12 wt% PEG-10,000 and 32.0 in 12 wt% PEG-10, 000 with 0.22M KI. The effect of anions and cations as well as ionic strength and pH on the partitioning of ovalbumin also matched ATPE heuristics. Using the heuristics established above, partition coefficients as high as 80 for bovine serum albumin and protein recoveries over 90% were achieved. In addition, the wide range of partition coefficients that were obtained for different proteins suggests the potential of the technique for separating proteins. Also, ovalbumin sorption capacities in dextran were as high as 450 mg/g dry polymer, and the sorption isotherms were linear over a broad protein concentration range.     

The immobilization of enzymes and cells of Bacillus stearothermophilus onto poly(maleic anhydride/styrene)-Co-polyethylene and poly(maleic anhydride/vinyl acetate)-Co-polyethylene

The graft copolymer, poly(maleic anhydride/styrene)-co-polyethylene was prepared. The copolymer immobilized bovine serum albumin (BSA), but the amount coupled appeared to be effected by the amount of styrene in the graft copolymer, temperature, and pH of the coupling medium. Competition existed between hydrolysis of the grafted anhydride groups and the protein. A graft copolymer with 66% add-on immobilized 4.5 mg/glucose oxidase/g copolymer, 4.6 mg alkaline phosphates/g copolymer and 0.2 mg cell of Bacillus stearothermophilus/g copolymer. A number of copolymers containing poly(maleic anhydride/vinyl acetate)-co-polyethylene were prepared to cover a range of grafting levels. These immobilized larger quantities of BSA, alkaline phosphatase, and cells of B. stearothermophilus than did the styrene graft copolymer. The copolymer was also hydrolyzed to release the hydroxyl group from the poly(vinyl acetate) component of the grafted chains. Using p-benzoquinone as the "activating agent," the copolymer coupled to BSA and to acid phosphatase. Using p-toluene-sulfonyl chloride, the copolymer was very effective in immobilizing trypsin.