Enhancing dopamine detection using a glassy carbon electrode modified with MWCNTs, quercetin, and Nafion

Glassy carbon (GC) electrode was modified using multi-wall carbon nanotubes (MWCNTs), quercetin (Q) and Nafion^® in this sequence. The thus modified electrode was used for the detection of dopamine (DA) in the presence of equimolar ascorbic acid (AA). It is demonstrated in this study that MWCNTs can increase the current response of DA by five-fold and Q can reduce the oxidation overpotential of DA by about 60 mV, compared to these parameters obtained with a bare GC electrode. It is also shown that a layer of Nafion^® can virtually eliminate the interference of AA for the detection of DA. The GC/MWCNTs/Q/Nafion^® electrode (hereafter also called composite electrode) shows a current density of about 900 μA cm⁻² for DA, compared to the value of 80 μA cm⁻² of the GC electrode and to the value of 390 μA cm⁻² of the GC/MWCNTs electrode. The 11-fold enhancement in the sensitivity of the GC electrode for DA determination is attributed to the composite modification of the electrode, and is substantiated through various cyclic voltammetric experiments. Cyclic voltammetry (CV) and linear sweep voltammetry were used to characterize the electrodes. Calibration curves of batch and flow systems were obtained by amperometry for the detection of DA. Additionally, the composite modified electrode was tested with a human serum sample for the determination of DA and was found to be promising at our preliminary experiments.     

Simultaneous determination of dopamine and serotonin on a glassy carbon electrode coated with a film of carbon nanotubes

A chemically modified electrode based on the carbon nanotube film-coated glassy carbon electrode (GCE) is described for the simultaneous determination of dopamine (DA) and serotonin (5-HT). The multiwall carbon nanotube (MWNT) film-coated GCE exhibits a marked enhancement effect on the current response of DA and 5-HT and lowers oxidation overpotentials. The responses of DA and 5-HT merge into a large peak at a bare GCE, but they yield two well-defined oxidation peaks at the MWNT film-coated GCE. The experimental parameters were optimized, and a direct electrochemical method for the simultaneous determination of DA and 5-HT was proposed. The interference of ascorbic acid (AA) was investigated, and the results showed that a large excess of AA did not interfere with the voltammetric responses of DA and 5-HT. The modified electrode has been successfully applied for the assay of 5-HT and DA in human blood serum.     

Electrochemical sensor for guanine using a self-assembled monolayer of 1,8,15,22-tetraaminophthalocyanatonickel(II) on glassy carbon electrode

This article describes the selective determination of guanine (G) using the self-assembled monolayer (SAM) of 1,8,15,22-tetraaminophthalocyanatonickel(II) (4α-Ni(II)TAPc) modified glassy carbon electrode (GCE) in 0.2 M acetate buffer solution (pH 4.0). The SAM of 4α-Ni(II)TAPc was formed on GCE by spontaneous adsorption of 1 mM 4α-Ni(II)TAPc in dimethylformamide (DMF). It shows two pairs of redox waves corresponding to Ni(III)/Ni(II) and Ni(III)Pc(-1)/Ni(III)Pc(-2) in 0.2 M acetate buffer solution. The SAM modified electrode exhibits excellent electrocatalytic activity toward the oxidation of G by enhancing its oxidation current with 150 mV less positive potential shift in contrast to bare GCE. Furthermore, the SAM modified electrode selectively determines G in the presence of high concentration of adenine (A). In differential pulse voltammetry measurements, the oxidation current response of G was increased linearly in the concentration range of 10 to 100 μM, and a detection limit was found to be 3×10(-8)M (signal/noise=3).     

Highly sensitive sensor for picomolar detection of insulin at physiological pH, using GC electrode modified with guanine and electrodeposited nickel oxide nanoparticles

The electrochemical behavior of insulin at glassy carbon (GC) electrode modified with nickel oxide nanoparticles and guanine was investigated. Cyclic voltammetry technique has been used for electrodeposition of nickel oxide nanoparticles (NiOx) and immobilization of guanine on the surface GC electrode. In comparison to glassy carbon electrode modified with nickel oxide nanoparticles and bare GC electrode modified with adsorbed guanine, the guanine/nickel oxide nanoparticles/modified GC electrode exhibited excellent catalytic activity for the oxidation of insulin in physiological pH solutions at reduced overpotential. The modified electrode was applied for insulin detection using cyclic voltammetry or hydrodynamic amperometry techniques. It was found that the calibration curve was linear up to 4muM with a detection limit of 22pM and sensitivity of 100.9pA/pM under the optimized condition for hydrodynamic amperometry using a rotating disk modified electrode. In comparison to other electrochemical insulin sensors, this sensor shows many advantages such as simple preparation method without using any special electron transfer mediator or specific reagent, high sensitivity, excellent catalytic activity at physiological pH values, short response time, long-term stability and remarkable antifouling property toward insulin and its oxidation product. Additionally, it is promising for the monitoring of insulin in chromatographic effluents.     

Ultrasensitive detection of l-cysteine using gold–5-amino-2-mercapto-1,3,4-thiadiazole core–shell nanoparticles film modified electrode

We are reporting the selective, sensitive and stable determination of l-cysteine (CY) at physiological pH (pH = 7.2) using a gold–aminomercaptothiadiazole core–shell nanoparticles (p-GAMCS NPs) film modified GC electrode. The p-GAMCS NPs film was fabricated on GC electrode by potentiodynamic method using 5-amino-2-mercapto-1,3,4-thiadiazole stabilized gold nanoparticles (AMT-AuNPs). The fabricated p-GAMCS NPs film was characterized by cyclic voltammetry and atomic force microscopy (AFM) techniques. The AFM image of the p-GAMCS NPs film showed that it contains a homogeneously distributed AuNPs with a spherical shape of ∼10 nm. The p-GAMCS NPs film modified GC electrode was exploited for the determination of CY. The bare GC electrode failed to show any response for CY (pH = 7.2) whereas p-GAMCS NPs film on GC electrode showed a well-defined oxidation peak for CY at 0.51 V. Further, p-GAMCS NPs film modified electrode successfully resolved the voltammetric signals of ascorbic acid (AA) and CY with a peak separation of 500 mV. This is the first report for the large voltammetric peak separation between CY and AA to the best of our knowledge. The amperometric current was increased linearly from 10 nM to 140 nM CY with a detection limit of 3 pM (S/N = 3). The present modified electrode showed better recoveries for spiked CY into the human blood serum and urine samples.     

The simultaneous electrochemical detection of ascorbic acid, dopamine, and uric acid using graphene/size-selected Pt nanocomposites

In this study, a graphene/Pt-modified glassy carbon (GC) electrode was created to simultaneously characterize ascorbic acid (AA), dopamine (DA), and uric acid (UA) levels via cyclic voltammetry (CV) and differential pulse voltammetry (DPV). During the preparation of the nanocomposite, size-selected Pt nanoparticles with a mean diameter of 1.7 nm were self-assembled onto the graphene surface. In the simultaneous detection of the three aforementioned analytes using CV, the electrochemical potential differences among the three detected peaks were 185 mV (AA to DA), 144 mV (DA to UA), and 329 mV (AA and UA), respectively. In comparison to the CV results of bare GC and graphene-modified GC electrodes, the large electrochemical potential difference that is achieved via the use of the graphene/Pt nanocomposites is essential to the distinguishing of these three analytes. An optimized adsorption of size-selected Pt colloidal nanoparticles onto the graphene surface results in a graphene/Pt nanocomposite that can provide a good platform for the routine analysis of AA, DA, and UA.     

Simultaneous determination of catecholamines, uric acid and ascorbic acid at physiological levels using poly(N-methylpyrrole)/Pd-nanoclusters sensor

An interesting electrochemical sensor has been constructed by the electrodeposition of palladium nanoclusters (Pd_nano) on poly(N-methylpyrrole) (PMPy) film-coated platinum (Pt) electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and scanning electron microscopy were used to characterize the properties of the modified electrode. It was demonstrated that the electroactivity of the modified electrode depends strongly on the electrosynthesis conditions of the PMPy film and Pd_nano. Moreover, the modified electrode exhibits strong electrocatalytic activity toward the oxidation of a mixture of dopamine (DA), ascorbic acid (AA), and uric acid (UA) with obvious reduction of overpotentials. The simultaneous analysis of this mixture at conventional (Pt, gold [Au], and glassy carbon) electrodes usually struggles. However, three well-resolved oxidation peaks for AA, DA, and UA with large peak separations allow this modified electrode to individually or simultaneously analyze AA, DA, and UA by using differential pulse voltammetry (DPV) with good stability, sensitivity, and selectivity. This sensor is also ideal for the simultaneous analysis of AA, UA and either of epinephrine (E), norepinephrine (NE) or l-DOPA. Additionally, the sensor shows strong electrocatalytic activity towards acetaminophen (ACOP) and other organic compounds. The calibration curves for AA, DA, and UA were obtained in the ranges of 0.05 to 1 mM, 0.1 to 10 μM, and 0.5 to 20 μM, respectively. The detection limits (signal/noise [S/N] = 3) were 7 μM, 12 nM, and 27 nM for AA, DA, and UA, respectively. The practical application of the modified electrode was demonstrated by measuring the concentrations of AA, DA, and UA in injection sample, human serum, and human urine samples, respectively, with satisfactory results. The reliability and stability of the modified electrode gave a good possibility for applying the technique to routine analysis of AA, DA, and UA in clinical tests.     

Hollow nitrogen-doped carbon microspheres pyrolyzed from self-polymerized dopamine and its application in simultaneous electrochemical determination of uric acid, ascorbic acid and dopamine

Hollow nitrogen-doped carbon microspheres (HNCMS) as a novel carbon material have been prepared and the catalytic activities of HNCMS-modified glassy carbon (GC) electrode towards the electro-oxidation of uric acid (UA), ascorbic acid (AA) and dopamine (DA) have also been investigated. Comparing with the bare GC and carbon nanotubes (CNTs) modified GC (CNTs/GC) electrodes, the HNCMS modified GC (HNCMS/GC) electrode has higher catalytic activities towards the oxidation of UA, AA and DA. Moreover, the peak separations between AA and DA, and DA and UA at the HNCMS/GC electrode are up to 212 and 136 mV, respectively, which are superior to those at the CNTs/GC electrode (168 and 114 mV). Thus the simultaneous determination of UA, AA and DA was carried out successfully. In the co-existence system of UA, AA and DA, the linear response range for UA, AA and DA are 5-30 μM, 100-1000 μM and 3-75 μM, respectively and the detection limits (S/N = 3) are 0.04 μM, 0.91 μM and 0.02 μM, respectively. Meanwhile, the HNCMS/GC electrode can be applied to measure uric acid in human urine, and may be useful for measuring abnormally high concentration of AA or DA. The attractive features of HNCMS provide potential applications in the simultaneous determination of UA, AA and DA.     

Ultrasensitive detection of L-cysteine using gold-5-amino-2-mercapto-1,3,4-thiadiazole core-shell nanoparticles film modified electrode

We are reporting the selective, sensitive and stable determination of L-cysteine (CY) at physiological pH (pH=7.2) using a gold-aminomercaptothiadiazole core-shell nanoparticles (p-GAMCS NPs) film modified GC electrode. The p-GAMCS NPs film was fabricated on GC electrode by potentiodynamic method using 5-amino-2-mercapto-1,3,4-thiadiazole stabilized gold nanoparticles (AMT-AuNPs). The fabricated p-GAMCS NPs film was characterized by cyclic voltammetry and atomic force microscopy (AFM) techniques. The AFM image of the p-GAMCS NPs film showed that it contains a homogeneously distributed AuNPs with a spherical shape of ~10 nm. The p-GAMCS NPs film modified GC electrode was exploited for the determination of CY. The bare GC electrode failed to show any response for CY (pH=7.2) whereas p-GAMCS NPs film on GC electrode showed a well-defined oxidation peak for CY at 0.51 V. Further, p-GAMCS NPs film modified electrode successfully resolved the voltammetric signals of ascorbic acid (AA) and CY with a peak separation of 500 mV. This is the first report for the large voltammetric peak separation between CY and AA to the best of our knowledge. The amperometric current was increased linearly from 10 nM to 140 nM CY with a detection limit of 3 pM (S/N=3). The present modified electrode showed better recoveries for spiked CY into the human blood serum and urine samples.     

A cyclodextrin host-guest recognition approach to an electrochemical sensor for simultaneous quantification of serotonin and dopamine

An electrochemical sensor for simultaneous quantification of serotonin (5-hydroxytryptamine, 5-HT) and dopamine (DA) using a β-cyclodextrin/poly(N-acetylaniline)/carbon nanotube composite modified carbon paste electrode has been developed. Synergistic effect of multi-walled carbon nanotube (MWCNT) in addition to the pre-concentrating effect of β-cyclodextrin (β-CD) as well as its different inclusion complex stability with 5-HT and DA was used to construct an electrochemical sensor for quantification of these important neurotransmitters. The overlapping anodic peaks of 5-HT and DA at 428 mV on bare electrode resolved in two well-defined voltammetric peaks at 202 and 363 mV vs. Ag/AgCl respectively. The oxidation mechanism of 5-HT and DA on the surface of the electrode was investigated by cyclic voltammetry and it was found that the electrode processes are pH dependent and electrochemical oxidation of 5-HT is totally irreversible while the electrode gave a more reversible process to DA. Under optimized conditions, linear calibration curves were obtained in the range of about 4-200 μM with a detection limits down to sub-μM levels (S/N=3) after 20-s accumulation, for both. The proposed sensor was shown to be remarkably selective for 5-HT and DA in matrices containing different species including ascorbic acid and uric acid. The suitability of the developed method was tested for the determination of 5-HT and DA in the Randox Synthetic Plasma samples and acceptable recoveries were obtained for a set of spiked samples.     

Electrochemical oxidation of purine and pyrimidine bases based on the boron-doped nanotubes modified electrode

Based on the excellent physicochemical properties of boron-doped carbon nanotubes (BCNTs), the electrochemical analysis of four free DNA bases at the BCNTs modified glassy carbon (GC) electrode was investigated. Herein, the BCNTs/GC electrode exhibited remarkable electrocatalytic activity towards the oxidation of purine bases (guanine (G), adenine (A)). More significantly, the direct oxidation of pyrimidine bases (thymine (T), cytosine (C)) was realized. It may be due to that BCNTs have the advantages of high electron transfer kinetics, large surface area, prominent antifouling ability and electrode activity. On basis of this, a novel and simple strategy for the determination of G, A, T and C was proposed. The BCNTs/GC electrode showed high sensitivity, wide linear range and capability of detection for the electrochemical determination of G, A, T, and C. On the other hand, the electrochemical oxidation of quaternary mixture of G, A, T, and C at the BCNTs/GC electrode was investigated. It was obtained that the peak separation between G and A, A and T, T and C were large enough for their potential recognition in mixture without any separation or pretreatment. The BCNTs/GC electrode also displayed good stability, reproducibility and excellent anti-interferent ability. Therefore, it can be believed that the BCNTs/GC electrode would provide a potential application for the electrochemical detection of DNA in the field of genetic-disease diagnosis.     

Determination of L-dopa using electropolymerized 3,3',3',3'-tetraaminophthalocyanatonickel(II) film on glassy carbon electrode

Electropolymerized film of 3,3',3',3'-tetraaminophthalocyanatonickel(II) (p-Ni(II)TAPc) on glassy carbon (GC) electrode was used for the selective and stable determination of 3,4-dihydroxy-L-phenylalanine (L-dopa) in acetate buffer (pH 4.0) solution. Bare GC electrode fails to determine the concentration of L-dopa accurately in acetate buffer solution due to the cyclization reaction of dopaquinone to cyclodopa in solution. On the other hand, p-Ni(II)TAPc electrode successfully determines the concentration of L-dopa accurately because the cyclization reaction was prevented at this electrode. It was found that the electrochemical reaction of L-dopa at the modified electrode is faster than that at the bare GC electrode. This was confirmed from the higher heterogeneous electron transfer rate constant (k(0)) of L-dopa at p-Ni(II)TAPc electrode (3.35 x 10(-2) cms(-1)) when compared to that at the bare GC electrode (5.18 x 10(-3) cms(-1)). Further, it was found that p-Ni(II)TAPc electrode separates the signals of ascorbic acid (AA) and L-dopa in a mixture with a peak separation of 220 mV. Lowest detection limit of 100 nM was achieved at the modified electrode using amperometric method. Common physiological interferents like uric acid, glucose and urea does not show any interference within the potential window of L-dopa oxidation. The present electrode system was also successfully applied to estimate the concentration of L-dopa in the commercially available tablets.     

Nonenzymatic electrochemical detection of glucose using well-distributed nickel nanoparticles on straight multi-walled carbon nanotubes

A nonenzymatic electrochemical sensor device was fabricated for glucose detection based on nickel nanoparticles (NiNPs)/straight multi-walled carbon nanotubes (SMWNTs) nanohybrids, which were synthesized through in situ precipitation procedure. SMWNTs can be easily dispersed in solution after mild sonication pretreatment, which facilitates the precursor of NiNPs binding to their surface and results in the homogeneous distribution of NiNPs on the surface of SMWNTs. The morphology and component of the nanohybrids were characterized by scanning electron microscopy (SEM) and X-ray powder diffraction (XRD), respectively. Cyclic voltammetry (CV) and amperometry were used to evaluate the catalytic activity of the NiNPs/SMWNTs nanohybrids modified electrode towards glucose. It was found that the nanohybrids modified electrode showed remarkably enhanced electrocatalytic activity towards the oxidation of glucose in alkaline solution compared to that of the bare glass carbon electrode (GCE), the NiNPs and the SMWNTs modified electrode, attributing to the synergistic effect of SMWNTs and Ni²⁺/Ni³⁺ redox couple. Under the optimal detection conditions, the as-prepared sensors exhibited linear behavior in the concentration range from 1 μM to 1 mM for the quantification of glucose with a limit of detection of 500 nM (3σ). Moreover, the NiNPs/SMWNTs modified electrode was also relatively insensitive to commonly interfering species such as ascorbic acid (AA), uric acid (UA), dopamine (DA), galactose (GA), and xylose (XY). The robust selectivities, sensitivities, and stabilities determined experimentally indicated the great potential of NiNPs/SMWNTs nanohybrids for construction of a variety of electrochemical sensors.     

Voltammetric discrimination of mandelic acid enantiomers

We report a novel electrochemical biosensor for direct discrimination of d- and l-mandelic acid (d- and l-MA) in aqueous medium. The glassy carbon electrode (GCE) surface was modified with reduced graphene oxide (rGO) and γ-globulin (GLOB). Electrochemical characterization of the modified electrodes was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The modified electrode surfaces were also characterized by scanning electron microscopy. Electrochemical response of the prepared electrode (GCE/rGO/GLOB) for discrimination of d- and l-MA enantiomers was investigated by cyclic voltammetry and was compared with bare GCE in the concentration range of 2 to 10 mM. Whereas the bare GCE showed no electrochemical response for the MA enantiomers, the GCE/rGO/GLOB electrode exhibited direct and selective discrimination with different oxidation potential values of 1.47 and 1.71 V and weak reduction peaks at potential values of −1.37 and −1.48 V, respectively. In addition, electrochemical performance of the modified electrode was investigated in mixed solution of d- and l-MA. The results show that the produced electrode can be used as electrochemical chiral biosensor for MA.     

SiO2/SnO2/Sb2O5 microporous ceramic material for immobilization of Meldola's blue: application as an electrochemical sensor for NADH

The mixed oxide SiO(2)/SnO(2), containing 25 wt% of SnO(2), determined by X-ray fluorescence, was prepared by the sol-gel method and the porous matrix obtained was then grafted with Sb (V), resulting the solid designated as (SiSnSb). XPS indicated 0.7% of Sb atoms on the surface. Sb grafted on the surface contains Br?nsted acid centers (SbOH groups) that can immobilize Meldola's blue (MB(+)) cationic dye onto the surface by an ion exchange reaction, resulting the solid designated as (SiSnSb/MB). In the present case a surface concentration of MB(+)=2.5×10(-11) mol cm(2) on the surface was obtained. A homogeneous mixture of the SiSnSb/MB with ultra pure graphite (99.99%) was pressed in disk format and used to fabricate a working electrode that displayed an excellent specific electrocatalytic response to NADH oxidation, with a formal potential of -0.05 V at pH 7.3. The electrochemical properties of the resulting electrode were investigated thoroughly with cyclic voltammetric and chronoamperometry techniques. The proposed sensor showed a good linear response range for NADH concentrations between 8×10(-5) and 9.0×10(-4) mol L(-1), with a detection limit of 1.5×10(-7) mol L(-1). The presence of dopamine and ascorbic acid did not show any interference in the detection of NADH on this modified electrode surface.     

Simultaneous electrochemical determination of dopamine, uric acid and ascorbic acid using palladium nanoparticle-loaded carbon nanofibers modified electrode

Palladium nanoparticle-loaded carbon nanofibers (Pd/CNFs) were prepared by electrospinning and subsequent thermal treatment processes. Pd/CNFs modified carbon paste electrode (Pd/CNF-CPE) displayed excellent electrochemical catalytic activities towards dopamine (DA), uric acid (UA) and ascorbic acid (AA). The oxidation overpotentials of DA, UA and AA were decreased significantly compared with those obtained at the bare CPE. Differential pulse voltammetry was used for the simultaneous determination of DA, UA and AA in their ternary mixture. The peak separation between UA and DA, DA and AA was 148 mV and 244 mV, respectively. The calibration curves for DA, UA and AA were obtained in the range of 0.5-160 microM, 2-200 microM, and 0.05-4mM, respectively. The lowest detection limits (S/N=3) were 0.2 microM, 0.7 microM and 15 microM for DA, UA and AA, respectively. With good selectively and sensitivity, the present method was applied to the determination of DA in injectable medicine and UA in urine sample.     

Self-assembled films of hemoglobin/laponite/chitosan: application for the direct electrochemistry and catalysis to hydrogen peroxide

A highly stable biological film was formed on the functional glassy carbon electrode (GCE) via step-by-step self-assembly of chitosan (CHT), laponite, and hemoglobin (Hb). Cyclic voltammetry (CV) of the Hb/laponite/CHT/GCE showed a pair of stable and quasi-reversible peaks for the Hb-Fe(III)/Fe(II) redox couple at about -0.035 V versus a saturated calomel electrode in pH 6.0 phosphate buffer at a scan rate of 0.1 V s(-1). The electrochemical reaction of Hb entrapped on the laponite/CHT self-assembled film exhibited a surface-controlled electrode process. The formal potential of the Hb-heme-Fe(III)/Fe(II) couple varied linearly with the increase of pH over the range of 3.0-8.0 with a slope of -63 mV pH(-1), which implied that an electron transfer was accompanied by single-proton transfer in the electrochemical reaction. The position of the Soret absorption band of this self-assembled Hb/laponite/CHT film suggested that the entrapped Hb kept its secondary structure similar to its native state. The self-assembled film showed excellent long-term stability, the CV peak potentials kept in the same positions, and the cathodic peak currents retained 90% of their values after 60 days. The film was used as a biological catalyst to catalyze the reduction of hydrogen peroxide. The electrocatalytic response showed a linear dependence on the H2O2 concentration ranging widely from 6.2 x 10(-6) to 2.55 x 10(-3) M with a detection limit of 6.2 x 10(-6) M at 3 sigma.     

Simultaneous determination of ascorbic acid and dopamine in the presence of uric acid on ruthenium oxide modified electrode

RuOx x nH2O film was electrochemically synthesized conveniently using cyclic voltammetric technique. The film formation was ascertained by the Electrochemical quartz crystal microbalance (EQCM) method and 45 ng of deposit per cycle was obtained. Stoichiometric ratio of the ruthenium and ruthenium oxide have been studied with different pH of phosphate buffer. The stability of the modified electrode in the presence of different cations and anions with different concentrations and pH were examined. Electrochemical studies have shown that the ascorbic acid (AA) and dopamine (DA) catalytic oxidation on ruthenium oxide modified electrode (RME) with a span of 300 mV separation even in the presence of uric acid (UA) with a large decrease in their respective over potential compared with bare glassy carbon electrode (GC). Accidentally, the reversible redox properties of the AA have been expediently studied on the RME using cyclic voltammetry and this peculiarity was interrogated through rotating ring disc electrode (RRDE) experiments. RRDE experiment results are conformed to the CV studies result and thus reversible redox property of AA have been reiterated. Amperometric detection under stirred condition up to approximately 0.8mM of AA and DA was carried out at free of electrode fouling. Interestingly, the regeneration of used RME electrode even after many consequent analysis, 100% was obtained.     

Electrochemical selective determination of ascorbic acid at redox active polymer modified electrode derived from direct blue 71

A simple selective method for determination of ascorbic acid using polymerized direct blue 71 (DB71) is described. Anodic polymerization of the azo dye DB71 on glassy carbon (GC) electrode in 0.1M H(2)SO(4) acidic medium was found to yield thin and stable polymeric films. The poly(DB71) films were electroactive in wide pH range (1-13). A pair of symmetrical redox peaks at a formal redox potential, E('0)=-0.02V vs. Ag/AgCl (pH 7.0) was observed with a Nernstian slope -0.058V, is attributed to a 1:1 proton+electron involving polymer redox reactions at the modified electrode. Scanning electron microscope (SEM), atomic force microscope (AFM) and electrochemical impedance spectroscopy (EIS) measurements were used for surface studies of polymer modified electrode. Poly(DB71) modified GC electrode showed excellent electrocatalytic activity towards ascorbic acid in neutral buffer solution. Using amperometric method, linear range (1x10(-6)-2x10(-3)M), dynamic range (1x10(-6)-0.01M) and detection limit (1x10(-6)M, S/N=3) were estimated for measurement of ascorbic acid in pH 7.0 buffer solution. Major interferences such as dopamine and uric acid are tested at this modified electrode and found that selective detection of ascorbic acid can be achieved. This new method successfully applied for determination of ascorbic acid in commercial tablets with satisfactory results.     

Design and characterization of electrochemical dopamine–aptamer as convenient and integrated sensing platform

Here, an ultrasensitive label-free electrochemical aptasensor was developed for dopamine (DA) detection. Construction of the aptasensor was carried out by electrodeposition of gold–platinum nanoparticles (Au–PtNPs) on glassy carbon (GC) electrode modified with acid-oxidized carbon nanotubes (CNTs–COOH). A designed complementary amine-capped capture probe (ssDNA1) was immobilized at the surface of PtNPs/CNTs–COOH/GC electrode through the covalent amide bonds formed by the carboxyl groups on the nanotubes and the amino groups on the oligonucleotides. DA-specific aptamer was attached onto the electrode surface through hybridization with the ssDNA1. Methylene blue (MB) was used as an electrochemical indicator that was intercalated into the aptamer through the specific interaction with its guanine bases. In the presence of DA, the interaction between aptamer and DA displaced the MB from the electrode surface, rendering a lowered electrochemical signal attributed to a decreased amount of adsorbed MB. This phenomenon can be applied for DA detection. The peak current of probe (MB) linearly decreased over a DA concentration range of 1–30 nM with a detection limit of 0.22 nM.