The Morse taper junction in modular revision hip replacement--a biomechanical and retrieval analysis.

All biomaterials used for total joint surgery are subjected to wear mechanisms. Morse taper junctions of modular hip revision implants are predilection sites for both fretting and crevice corrosion, dissociation and breakage of the components. The aim of this study is to quantify wear and study metallurgical changes of Morse taper junctions of in-vitro and in-vivo loaded modular revision stems. Three modular revision stems (MRP-Titan, Peter Brehm GmbH, Germany) were loaded by a servohydraulic testing machine. The loads and conditions used exceeded by far the values required by ISO-standard 7206. The tests were performed with maximum axial loads of 3,500 N to 4,000 N over 10-12 x 10(6) cycles at 2 Hz. Additionally, the female part of the taper junctions were coated with blood and bone debris. The free length of the implant was set to 200 mm. One other MRP stem was investigated after retrieval following 5.5 years of in-vivo use. All contact surfaces of the modular elements were assessed by visual inspection, optical microscopy and scanning electron microscopy (SEM). The degree of plastic deformation of the male part of the morse taper junction was determined by contouroscopy. None of the morse taper junctions broke or failed mechanically. Corrosion and wear affected all tapers, especially at the medial side. The retrieved implant showed no cracks and the amount of debris measured only one third of that for the stems tested in-vitro. The present retrieval and laboratory investigations have proven, that the morse taper junctions of the MRP-titanium stem are stable and resistant to relevant wear mechanisms. The longevity of the junctions for clinical use is given. If an optimal taper design is selected, the advantages of modular femoral components in total hip revision arthroplasty will outweigh the possible risks.     

Population-based rates of revision of primary total hip arthroplasty: a systematic review

Background

Most research on failure leading to revision total hip arthroplasty (THA) is reported from single centers. We searched PubMed between January 2000 and August 2010 to identify population- or community-based studies evaluating ten-year revision risks. We report ten-year revision risk using the Kaplan-Meier method, stratifying by age and fixation technique.

Results

Thirteen papers met the inclusion criteria. Cemented prostheses had Kaplan-Meier estimates of revision-free implant survival of ten years ranging from 88% to 95%; uncemented prostheses had Kaplan-Meier estimates from 80% to 85%. Estimates ranged from 72% to 86% in patients less than 60 years old and from 90 to 96% in older patients.

Conclusion

Data reported from national registries suggest revision risks of 5 to 20% ten years following primary THA. Revision risks are lower in older THA recipients. Uncemented implants may have higher ten-year rates of revision, regardless of age.     

Cement mantle fatigue failure in total hip replacement: experimental and computational testing

One possible loosening mechanism of the femoral component in total hip replacement is fatigue cracking of the cement mantle. A computational method capable of simulating this process may therefore be a useful tool in the preclinical evaluation of prospective implants. In this study, we investigated the ability of a computational method to predict fatigue cracking in experimental models of the implanted femur construct. Experimental specimens were fabricated such that cement mantle visualisation was possible throughout the test. Two different implant surface finishes were considered: grit blasted and polished. Loading was applied to represent level gait for two million cycles. Computational (finite element) models were generated to the same geometry as the experimental specimens, with residual stress and porosity simulated in the cement mantle. Cement fatigue and creep were modelled over a simulated two million cycles. For the polished stem surface finish, the predicted fracture locations in the finite element models closely matched those on the experimental specimens, and the recorded stem displacements were also comparable. For the grit blasted stem surface finish, no cement mantle fractures were predicted by the computational method, which was again in agreement with the experimental results. It was concluded that the computational method was capable of predicting cement mantle fracture and subsequent stem displacement for the structure considered.     

A novel sensor concept for optimization of loosening diagnostics in total hip replacement

The main reason for the revision of total hip replacements is aseptic loosening, caused by stress shielding and wear particle induced osteolysis. In order to detect an implant loosening early, the osseointegration of endoprosthetic implants must be measured exactly. Currently applied diagnostic methods, such as standard radiographs and clinical symptomatology, often result in an imprecise diagnosis. A novel radiation-free method to improve the diagnostic investigation of implant loosening is presented. The osseointegration of an implant can be identified using mechanical magnetic sensors (oscillators), which impinge on small membranes inside an implant component, e.g., the femoral hip stem. The maximum velocity after impingement of the oscillator depends on the osseointegration of the implant. Excitation of the oscillator is realized by a coil outside the human body. Another external coil is used to detect the velocity of the oscillator. To demonstrate the principle of the novel loosening sensor, an overdimensioned test device was designed to measure simulated loosening phases in the first experimental tests with different material layers. The overdimensioned test device of the loosening sensor showed significant differences in the various phases of fixation. Analysis of the membrane without any material layer in the case of advanced loosening resulted in a 23% higher maximum velocity compared to an attached artificial bone layer. Based on these preliminary results, the sensor system shows potential for the detection of implant loosening. Moreover, the proposed system could be used in experimental applications to determine the quality of bioactive coatings and new implant materials.     

A numerically validated probabilistic model of a simplified total hip replacement construct

Hip replacement constructs are paradigms of uncertain systems, and as such are suited to the application of probabilistic methods to assess their structural integrity. In order to gain confidence in a probabilistic model, it would be useful to verify the findings with experimental data; however, this is difficult to achieve in practice because of the exhaustive number of parameter combinations that need to be tested. As an alternative to experimental testing, benchmarking can be carried out provided a known analytical solution is available. To this end, a simplified 2D two-beam model of the femoral part of a total hip replacement construct was utilised to analyse uncertainties and variability in the construct as it is subjected to load. The use of a simplified model enabled geometric parameters to be investigated; these are commonly not considered in probabilistic models due to the increased complexity involved. Analytical and finite element representations of the model were developed and compared. The probabilistic study used the Monte Carlo simulation technique and the first-order reliability method to look at the inducible displacement of a hip implant, a phenomenon that has been linked to the most common cause of hip implant failure, aseptic loosening. Excellent correlation was observed between the analytical and probabilistic solutions, and it was shown that probabilistic approaches could efficiently predict the response of the simplified beam model while readily identifying the parameters most likely to compromise the structural integrity of the construct.     

A numerically validated probabilistic model of a simplified total hip replacement construct

Hip replacement constructs are paradigms of uncertain systems, and as such are suited to the application of probabilistic methods to assess their structural integrity. In order to gain confidence in a probabilistic model, it would be useful to verify the findings with experimental data; however, this is difficult to achieve in practice because of the exhaustive number of parameter combinations that need to be tested. As an alternative to experimental testing, benchmarking can be carried out provided a known analytical solution is available. To this end, a simplified 2D two-beam model of the femoral part of a total hip replacement construct was utilised to analyse uncertainties and variability in the construct as it is subjected to load. The use of a simplified model enabled geometric parameters to be investigated; these are commonly not considered in probabilistic models due to the increased complexity involved. Analytical and finite element representations of the model were developed and compared. The probabilistic study used the Monte Carlo simulation technique and the first-order reliability method to look at the inducible displacement of a hip implant, a phenomenon that has been linked to the most common cause of hip implant failure, aseptic loosening. Excellent correlation was observed between the analytical and probabilistic solutions, and it was shown that probabilistic approaches could efficiently predict the response of the simplified beam model while readily identifying the parameters most likely to compromise the structural integrity of the construct.     

Bending and fracture of the femoral component in cemented total hip replacement

A computer method was used to make 41 measurements on the geometry of insertion of the femoral component in 200 Charnley total hip replacements. Surgery had been performed at least 12 years before, giving results which were classified as: success (90); fracture (56); or loose (54), according to rigid selection criteria. Fracture was associated with heavier patients in which there was poor proximal fixation of the femoral component but adequate distal fixation. Stems with a medial disposition proximally were more common in the fracture group than in the successful or loose groups. Sequential measurements of bending and subsequent fracture were made on the follow-up radiographs of 24 of the 200 cases (6 fracture and 18 successful). These measurements allowed bending to be detected at an earlier stage than by simple inspection of the radiographs.     

Characteristics of sit-to-stand and gait coordination in patients with total hip replacement

Upright posture, standing up from a chair, and gait were analyzed in patients after one-sided total hip replacement and in healthy subjects (control). It was found that the patients predominantly loaded the unoperated leg when they stood quietly or rose from a chair. Subjects’ walking on a 10-m podograph treadmill showed that their walking speed was slower than that of healthy subjects and the swing phase on the side of hip replacement was longer than on the unoperated side. It was assumed that the unequal load on legs during walking, standing, and sit-to-stand performance in patients with total hip replacement was related to the sensory deficit of the artificial joint, leading to the overstrain of the unoperated leg and coxarthrosis in it.     

Aseptic loosening of the femoral component in cemented total hip replacement

The purpose of this study was to identify factors which predispose to aseptic loosening of the femoral component in cemented total hip replacement. Its design was based on rigid selection critria, so that successful and loose replacements which employed the same surgical technique were compared. Measurements of patient anatomy and of the insertion of the femoral component were made, by an accurate computer technique, on initial post-operative radiographs. Loosening was associated with heavier patients with a wider medullary canal which was flared proximally. This difference in anatomy led to differing distributions of cement in the successful and loose replacements. Medial cement-bone demarcation, at the mid-stem level, was also associated with loosening. These findings indicate the importance of optimizing the size of the prosthesis with respect to the femoral morphology.     

Long-term risk of receiving a total hip replacement in cancer patients

Aim: To investigate whether cancer patients have an increased risk of receiving a total hip replacement compared to the standard population of Norway. Materials and methods: By linking of The Cancer Register of Norway and The Norwegian Arthroplasty Register we obtained information on cancer diagnoses (type, date of diagnosis), total hip arthroplasties and date of death for all patients living in Norway. This includes 741,901 patients categorized into three groups: 652,197 patients with at least one cancer diagnosis but no hip arthroplasties, 72,469 patients with at least one hip arthroplasty but no cancer diagnosis and 17,235 patients who have at least one cancer diagnosis and at least one hip arthroplasty. Within this latter group, 8563 individuals had been diagnosed with cancer prior to a total hip arthroplasty. Statistical methods applied in this study were Cox interval censored regression models and standardized incidence ratios (SIR). Results: Cancer patients had a slightly increased risk of receiving a total hip arthroplasty compared to the Norwegian population (SIR = 1.15 (95% CI, 1.12–1.17)). For primary tumours located cranially to the pelvic area there was no significant increase in risk for hip arthroplasty. An exception was breast cancer (SIR = 1.13 (95% CI 1.08–1.18)). Cancer located in the pelvic region (SIR = 1.20 (95% CI 1.16–1.24)), malignant lymphoma (SIR = 1.30 (95% CI 1.15–1.46)) and leukaemia (SIR = 1.17 (95% CI 1.01–1.34)) had an increased risk for receiving a total hip arthroplasty. Conclusion: Cancer survivors, mainly those with pelvic and lympho-hematological malignancies, have a small statistically significant increase in risk for receiving total hip arthroplasty.     

Dependence of stem stress in total hip replacement on prosthesis and cement stiffness

Two dimensional finite element analyses were used to determine the direct tensile stress distributions along the lateral edge of the stem of the femoral component of a total hip replacement. The efficacy of using two-dimensional analysis for three-dimensional composite structures was assessed, and the two-dimensional model was found to be suitable for parametric studies. Various combinations of stem and cement stiffnesses were investigated. In particular the influence of stem taper, cement stiffness, prosthesis stiffness and the effect of a plateau on the prosthesis stresses, were examined and compared. The most significant factor was found to be the modulus of elasticity of the stem material. The tensile stresses decrease with decreasing modulus. Cement stiffness and stem shape appeared to have for less effect on stem stress.     

A mathematical formula to calculate the theoretical range of motion for total hip replacement

The reduced range of motion (ROM) resulting from total hip replacement (THR) leads to frequent prosthetic impingement, which may restrict activities of daily living and cause subluxation and dislocation. Therefore, to know the ROM of THR is very important in clinical situations and in the design of prostheses. THR involves a pure ball and socket joint. We created a mathematical formula to calculate the theoretical ROM of THR limited by the prosthetic impingement. The ROM of THR is governed by the following five factors, (1) The prosthetic ROM (oscillation angle: obtained from company data), (2) cup abduction (3) cup anterior opening, (4) the angle of the femoral neck component from the horizontal plane, and (5) the femoral neck anteversion. The last 4 factors are able to be obtained from anterior-posterior, axial X-rays and CT of the patient's THR. The objective was to create mathematical formulas that could accurately and quickly calculate the ROM of THR. By entering the five values into a computer programmed with the formulas, one could obtain the ROM for the THR. This reveals the effect on ROM of the oscillation angle and the interaction of ROM with cup abduction, anterior opening and neck anteversion. Furthermore this readily would enable a clinical evaluation of the possibility of postoperative dislocation and help in postoperative rehabilitation. The calculated numerical values of ROM by these mathematical formulas were successfully compared with the ROMs obtained from 3-dimensional computer graphics (3D-CG).     

Benefits of total hip replacement to older patients and the community.

The benefits of total hip replacement in 49 people aged 55-84 with osteoarthrosis of the hip were evaluated. The main benefit was relief of symptoms, 40 patients being pain free after operation. Range of hip movement and mobility improved moderately in most patients. After operation most patients were better able to perform certain activities of daily life, though only six were completely independent, the rest requiring aids or help from others. Nevertheless, 18 of the patients'' main helpers estimated that they had more time free of tasks previously performed for the patient. There was a small reduction in the need for community medical resources such as home visits from general practitioners or district nurses. Thirteen patients were still taking antiarthritic drugs. Older patients needed to spend longer in hospital after operation because of complications. It was concluded that total hip replacement contributed to improving the quality of life of patients and their helpers, while also helping to reduce the demand for community health and welfare services.     

Translation of biomechanical concepts in bone tissue engineering: from animal study to revision knee arthroplasty

Bone defects in revision knee arthroplasty are often located in load-bearing regions. The goal of this study was to determine whether a physiologic load could be used as an in situ osteogenic signal to the scaffolds filling the bone defects. In order to answer this question, we proposed a novel translation procedure having four steps: (1) determining the mechanical stimulus using finite element method, (2) designing an animal study to measure bone formation spatially and temporally using micro-CT imaging in the scaffold subjected to the estimated mechanical stimulus, (3) identifying bone formation parameters for the loaded and non-loaded cases appearing in a recently developed mathematical model for bone formation in the scaffold and (4) estimating the stiffness and the bone formation in the bone-scaffold construct. With this procedure, we estimated that after 3 years mechanical stimulation increases the bone volume fraction and the stiffness of scaffold by 1.5- and 2.7-fold, respectively, compared to a non-loaded situation.