Electrospun Chitosan Microspheres for Complete Encapsulation of Anionic Proteins: Controlling Particle Size and Encapsulation Efficiency

Electrospinning was employed to fabricate chitosan microspheres by a single-step encapsulation of proteins without organic solvents. Chitosan in acetic acid was electrospun toward a grounded sodium carbonate solution at various electric potential and feeding rates. Electrospun microspheres became insoluble and solidified in the sodium carbonate solution by neutralization of chitosan acetate. When the freeze-dried microspheres were examined by scanning electron microscopy, the small particle size was obtained at higher voltages. This is explained by the chitosan droplet size at the electrospinning needle was clearly controllable by the electric potential. The recovery yield of chitosan microspheres was dependent on the concentration of chitosan solution due to the viscosity is the major factor affecting formation of chitosan droplet during curling of the electrospinning jets. For protein encapsulation, fluorescently labeled bovine serum albumin (BSA) was codissolved with chitosan in the solution and electrospun. At higher concentration of sodium carbonate solution and longer solidification time in the solution, the encapsulation efficiency of the protein was confirmed to be significantly high. The high encapsulation efficiency was achievable by instant solidification of microspheres and electrostatic interactions between chitosan and BSA. Release profiles of BSA from the microspheres showed that the protein release was faster in acidic solution due to dissolution of chitosan. Reversed-phase chromatography of the released fractions confirmed that exposure of BSA to acidic solution during the electrospinning did not result in structural changes of the encapsulated protein.     

Cerium ion-chelated magnetic silica microspheres for enrichment and direct determination of phosphopeptides by matrix-assisted laser desorption ionization mass spectrometry

In this study, we employed, for the first time, the Ce4+-chelated magnetic silica microspheres to selectively concentrate phosphopeptides from protein digest products. Cerium ions were chelated onto magnetic silica microspheres using the strategy we established before. After enrichment, the phosphopeptide-conjugated magnetic microspheres were separated from the sample solution just by using a magnet. With the optimized enrichment conditions, the performance of the Ce4+-chelated magnetic microspheres was compared with the Fe3+-chelated microspheres using tryptic digested peptides originating from ovalbumin, a five protein mixture containing phosphoproteins and nonphosphoproteins, as well as a mixture of beta-casein and BSA with a molar ratio of 1:50. Compared to Fe3+, Ce4+-chelated magnetic microspheres exhibited more selective isolation ability for concentrating phosphopeptides from complex mixtures. Even when the amount of the tryptic digest product of BSA is 50 times higher than that of beta-casein in the sample solution, the trace phosphopeptides derived from beta-casein can still be concentrated effectively by the Ce4+-chelated magnetic microspheres in only 30 s. Furthermore, we initially utilized the Ce4+-chelated magnetic microspheres to directly enrich phosphopeptides from human serum without extra purification steps or tedious treatment, which opens up a possibility for their further application in phosphoproteomics.     

Reversible immobilization of glucoamylase onto magnetic chitosan nanocarriers

A simple preparation process for the monodispersed pH-sensitive core-shell magnetic microspheres was carried out consisting of chitosan self-assembled on magnetic iron oxide nanoparticles. Meanwhile, glucoamylase was immobilized as a model enzyme on this carrier of Fe₃O₄/CS microspheres by ionic adsorption. The morphology, inner structure, and high magnetic sensitivity of the resulting magnetic chitosan microspheres were studied, respectively, with a field emission scanning electron microscope (SEM), transmission electron microscope (TEM), FT-IR spectroscopy, thermogravimetric analysis (TGA), and a vibrating sample magnetometer (VSM). Subsequently, the properties of glucoamylase immobilized on the regenerated supports were also investigated by determining storage stability, pH stability, reusability, magnetic response, and regeneration of supports. The results from characterization and determination remarkably indicated that the immobilized glucoamylase obtained presents excellent storage stability, pH stability, reusability, magnetic response, and regeneration of supports. Therefore, this kind of magnetic Fe₃O₄/CS microspheres with perfect monodispersity should be an ideal support for enzyme immobilization.     

Preparation and characterization of temperature-sensitive poly(N-isopropylacrylamide)-b-poly(D,L-lactide) microspheres for protein delivery

Temperature-sensitive diblock copolymers, poly(N-isopropylacrylamide)-b-poly(D,L-lactide) (PNIPAAm-b-PLA) with different PNIPAAm contents were synthesized and utilized to fabricate microspheres containing bovine serum albumin (BSA, as a model protein) by a water-in-oil-in-water double emulsion solvent evaporation process. XPS analysis showed that PNIPAAm was a dominant component of the microspheres surface. BSA was well entrapped within the microspheres, and more than 90% encapsulation efficiency was achieved. The in vitro degradation behavior of microspheres was investigated using SEM, NMR, FTIR, and GPC. It was found that the microspheres were erodible, and polymer degradation occurred in the PLA block. Degradation of PLA was completed after 5 months incubation in PBS (pH 7.4) at 37 degrees C. A PVA concentration of 0.2% (w/v) in the internal aqueous phase yielded the microspheres with an interconnected porous structure, resulting in fast matrix erosion and sustained BSA release. However, 0.05% PVA produced the microspheres with a multivesicular internal structure wrapped with a dense skin layer, resulting in lower erosion rate and a biphasic release pattern of BSA that was characterized with an initial burst followed by a nonrelease phase. The microspheres made from PNIPAAm-b-PLA with a higher portion of PNIPAAm provided faster BSA release. In addition, BSA release from the microspheres responded to the external temperature changes. BSA release was slower at 37 degrees C (above the LCST) than at a temperature below the LCST. The microspheres fabricated with PNIPAAm-b-PLA having a 1:5 molar ratio of PNIPAAm to PLA and 0.2% (w/v) PVA in the internal aqueous phase provided a sustained release of BSA over 3 weeks in PBS (pH 7.4) at 37 degrees C.     

Highly selective and rapid enrichment of phosphorylated peptides using gallium oxide-coated magnetic microspheres for MALDI-TOF-MS and nano-LC-ESI-MS/MS/MS analysis

In this work, we present, to our knowledge, the first demonstration of the utility of iron oxide magnetic microspheres coated with gallium oxide for the highly selective enrichment of phosphopeptide prior to mass spectrometric analysis. These microspheres that we prepared not only have a shell of gallium oxide, giving them a high-trapping capacity for the phosphopeptides, but also their magnetic property enables easy isolation by positioning an external magnetic field. Tryptic digest products of phosphoproteins including beta-casein, ovalbumin, casein, as well as five protein mixtures were used as the samples to exemplify the feasibility of this approach. In very short time (only 0.5 min), phosphopeptides sufficient for characterization by MALDI-TOF-MS were selectively enriched by the Ga(2)O(3)-coated Fe(3)O(4) microspheres. The performance of the Ga(2)O(3)-coated Fe(3)O(4) microspheres were further compared with Fe(3+)-immobilized magnetic silica microspheres, commercial Fe(3+)-IMAC resin, and TiO2 beads for enrichment of peptides originating from tryptic digestion of beta-casein and BSA with a molar ratio of 1:50, and the results proved a stronger selective ability of Ga(2)O(3)-coated Fe(3)O(4) microspheres over the other materials. Finally, the Ga(2)O(3)-coated Fe(3)O(4) microspheres were successfully utilized for enrichment of phosphopeptides from digestion products of rat liver extract. All results show that Ga(2)O(3)-coated Fe(3)O(4) microsphere is an effective material for selective isolation and concentration of phosphopeptides.     

Preparation of Fe3O4@ZrO2 core-shell microspheres as affinity probes for selective enrichment and direct determination of phosphopeptides using matrix-assisted laser desorption ionization mass spectrometry

Fe3O4@ZrO2 microspheres with well-defined core-shell structure were prepared and applied for the highly selective enrichment of phosphopeptides from tryptic digest product of proteins. To successfully coat iron oxide microspheres with uniform zirconia shell, magnetic Fe3O4 microspheres were first synthesized via a solvothermal reaction, followed by being coated with a thin layer of carbon by polymerization and carbonization of glucose through hydrothermal reaction. Finally, with the use of the Fe3O4@C microspheres as templates, zirconium isopropoxide was prehydrolyzed and absorbed onto the microspheres and eventually converted into zirconia by calcinations. The as-prepared Fe3O4@ZrO2 core-shell microspheres were used as affinity probes to selectively concentrate phosphopeptides from tryptic digest of beta-casein, casein, and five protein mixtures to exemplify their selective enrichment ability of phosphopeptides from complex protein samples. In only 0.5 min, phosphopeptides sufficient for characterization by MALDI-MS could be enriched by the Fe3O4@ZrO2 microspheres. The results demonstrate that Fe3O4@ZrO2 microspheres have the excellent selective enrichment capacity for phosphopeptides from complex samples. The performance of the Fe3O4@ZrO2 microspheres was further compared with commercial IMAC beads for the enrichment of peptides originating from tryptic digestion of beta-casein and bovine serum albumin (BSA) with a molar ratio of 1:50, and the results proved a stronger selective ability of Fe3O4@ZrO2 microspheres over IMAC beads. Finally, the Fe3O4@ZrO2 microspheres were successfully utilized for enrichment of phosphopeptides from human blood serum without any other purification procedures.     

Bioinorganic transformations of liver iron deposits observed by tissue magnetic characterisation in a rat model

The magnetic properties and the ultrastructure, with special emphasis on the nanometric range, of liver tissues in an iron overload rat model have been investigated. The tissues of the animals, sacrificed at different times after a single iron dextran injection, have been characterised by magnetic AC susceptibility measurements together with transmission electron microscopy (TEM) and selected area electron diffraction (SAED) as helping techniques. It has been observed that few days after the iron administration the liver contains at least two iron species: (i) akaganéite nanoparticles, coming from iron dextran and (ii) ferrihydrite nanoparticles corresponding to ferritin. The magnetic susceptibility of the tissues depends not only on the elemental iron content but also on its distribution among chemical species, and varies in a remarkable regular manner as a function of the elapsed time since the iron administration. The results are of relevance with respect to non-invasive techniques for liver iron determination, directly or indirectly based on the magnetic susceptibility of the tissues, as biomagnetic liver susceptometry (BLS) and magnetic resonance (MRI) image treatment.     

Emulsan, a tailorable biopolymer for controlled release

Microsphere hydrogels made with emulsan-alginate were used as carrier for the microencapsulation of blue dextran in order to study the effect of emulsan on the alginate bead stability. Blue dextran release studies indicated an increase of microsphere stability in presence of emulsan, as a coating agent. BSA adsorption by emulsan-alginate microspheres is also enhanced 40% compared to alginate alone. XPS studies confirm the presence of BSA adsorbed on emulsan microsphere surfaces. These results are in agreement with the equilibrium adsorption model of Freundlich. Studies of BSA adsorption using non-equilibrium Lagergren second-order and intraparticle models, are suggesting a complex mechanisms of protein adsorption by chemisorption and intraparticle diffusion. Also, enzymatic release of BSA from emulsan microspheres containing azo-BSA under physiological conditions is suggests the possibility of using microspheres as a depot for pre-proteins of medical interest.     

Separation of cells labeled with immunospecific iron dextran microspheres using high gradient magnetic chromatography

Immunospecific magnetic microspheres, consisting of ferromagnetic iron dextran conjugated to Protein A, were used to specifically label red blood cells (RBC) for cell separation studies using high gradient magnetic chromatography ( HGMC ). When 10(7)-10(8) RBC labeled with Protein A-iron dextran microspheres were applied to a column containing 30 mg stainless steel wire placed in a 7.5 kilogauss magnetic field, 96 +/- 2% of the cells were retained in the column. These cells could be eluted by removing the magnetic field and mechanically agitating the column. The retention of labeled cells by HGMC was shown to be dependent on the applied magnetic field and the amount of wire packed into the column. HGMC in conjunction with cell labeling with immunospecific iron dextran microspheres have useful applications for the separation of specific cell types.     

Process and formulation variables in the preparation of injectable and biodegradable magnetic microspheres

The aim of this study was to prepare biodegradable sustained release magnetite microspheres sized between 1 to 2 μm. The microspheres with or without magnetic materials were prepared by a W/O/W double emulsion solvent evaporation technique using poly(lactide-co-glycolide) (PLGA) as the biodegradable matrix forming polymer. Effects of manufacturing and formulation variables on particle size were investigated with non-magnetic microspheres. Microsphere size could be controlled by modification of homogenization speed, PLGA concentration in the oil phase, oil phase volume, solvent composition, and polyvinyl alcohol (PVA) concentration in the outer water phase. Most influential were the agitation velocity and all parameters that influence the kinematic viscosity of oil and outer water phase, specifically the type and concentration of the oil phase. The magnetic component yielding homogeneous magnetic microspheres consisted of magnetite nanoparticles of 8 nm diameter stabilized with a polyethylene glycole/polyacrylic acid (PEG/PAA) coating and a saturation magnetization of 47.8 emu/g. Non-magnetic and magnetic microspheres had very similar size, morphology, and size distribution, as shown by scanning electron microscopy. The optimized conditions yielded microspheres with 13.7 weight% of magnetite and an average diameter of 1.37 μm. Such biodegradable magnetic microspheres seem appropriate for vascular administration followed by magnetic drug targeting.     

Formation and characterization of superparamagnetic cross-linked high amylose starch

A gelatinized cross-linked high amylose starch matrix with magnetic properties was synthesized via in situ formation of iron oxides inside the polymer matrix. Precipitation and multiple oxidation of ferrous ions were performed. The samples were observed using transmission and scanning electron microscopy, showing morphological changes in the magnetic and polymer phases. The iron content analysis revealed a decay from one oxidation cycle to the next one if no fresh ferrous solutions are added before the multiple oxidation. X-ray diffractograms, magnetization curves and Mössbauer spectra were also recorded for the characterization of the magnetic phase. The products exhibit superparamagnetic properties due to the presence of ferrimagnetic nanoparticles, although some other iron compounds are also present.     

Novel thymine-functionalized polystyrenes for applications in biotechnology. 2. Adsorption of model proteins

This paper investigates the adsorption of bovine serum albumin (BSA) and bovine hemoglobin (BHb) model proteins onto novel thymine-functionalized polystyrene (PS-VBT) microspheres, in comparison with polystyrene (PS) microspheres. Maximum adsorption was obtained for both proteins near their corresponding isoelectric points (pI at pH = 4.7 for BSA and 7.1 for BHb). FTIR and adsorption isotherm analysis demonstrated that, although both proteins were physisorbed onto PS through nonspecific hydrophobic interactions, adsorption onto the functionalized copolymers occurred by both physisorption and chemisorption via hydrogen bonding. FTIR analysis also indicated conformational changes in the secondary structure of BSA and BHb adsorbed onto PS, whereas little or no conformation change was seen in the case of adsorption onto PS-VBT. Atomic force microscopy (AFM), consistent with the isotherm results, also demonstrated monolayer adsorption for both proteins. AFM images of BSA adsorbed onto copolymers with 20 mol % surface VBT loading showed exclusively end-on orientation. Adsorption onto copolymers with lower functionality showed mixed end-on and side-on orientation modes of BSA, and only the side-on orientation was observed on PS. The AFM results agreed well with theoretically calculated and experimentally obtained adsorption capacities. AFM together with calculated and observed adsorption capacity data for BHb indicated that this protein might be highly compressed on the copolymer surface. Adsorption from a binary mixture of BSA and BHb onto PS-VBT showed good separation at pH=7.0; approximately 90% of the adsorbed protein was BHb. The novel copolymers have potential applications in biotechnology.     

New monodisperse magnetic polymer microspheres biofunctionalized for enzyme catalysis and bioaffinity separations

Magnetic macroporous PGMA and PHEMA microspheres containing carboxyl groups are synthesized by multi-step swelling and polymerization followed by precipitation of iron oxide inside the pores. The microspheres are characterized by SEM, IR spectroscopy, AAS, and zeta-potential measurements. Their functional groups enable bioactive ligands of various sizes and chemical structures to couple covalently. The applicability of these monodisperse magnetic microspheres in biospecific catalysis and bioaffinity separation is confirmed by coupling with the enzyme trypsin and huIgG. Trypsin-modified magnetic PGMA-COOH and PHEMA-COOH microspheres are investigated in terms of their enzyme activity, operational and storage stability. The presence of IgG molecules on microspheres is confirmed.     

Synthesis of novel porous magnetic silica microspheres as adsorbents for isolation of genomic DNA

An improved procedure is described for preparation of novel mesoporous microspheres consisting of magnetic nanoparticles homogeneously dispersed in a silica matrix. The method is based on a three-step process, involving (i) formation of hematite/silica composite microspheres by urea-formaldehyde polymerization, (ii) calcination of the composite particles to remove the organic constituents, and (iii) in situ transformation of the iron oxide in the composites by hydrogen reductive reaction. The as-synthesized magnetite/silica composite microspheres were nearly monodisperse, mesoporous, and magnetizable, with as typical values an average diameter of 3.5 microm, a surface area of 250 m(2)/g, a pore size of 6.03 nm, and a saturation magnetization of 9.82 emu/g. These magnetic particles were tested as adsorbents for isolation of genomic DNA from Saccharomyces cerevisiae cells and maize kernels. The results are quite encouraging as the magnetic particle based protocols lead to the extraction of genomic DNA with satisfactory integrity, yield, and purity. Being hydrophilic in nature, the porous magnetic silica microspheres are considered a good alternative to polystyrene-based magnetic particles for use in biomedical applications where nonspecific adsorption of biomolecules is to be minimized.     

Adsorption of bovin serum albumin (BSA) onto the magnetic chitosan nanoparticles prepared by a microemulsion system

The adsorption characteristics of BSA onto the magnetic chitosan nanoparticles have been investigated in this paper. The magnetic chitosan nanoparticles were prepared by adding the basic precipitant of NaOH solution into a W/O microemulsion system. The morphology of magnetic chitosan nanoparticles was observed by transmission electron microscope (TEM). It was found that the diameter of magnetic chitosan nanoparticles was from 10nm to 20 nm, and the nanoparticles suspending in the aqueous solution could easily aggregate by a magnet, which suggested that the nanoparticles had good magnetic characteristics. The BSA adsorption experiment indicated that when pH of BSA solution was equal to 4, the maximum adsorption loading reached 110 mg/g. Through measuring the zeta potential of BSA solution and the magnetic nanoparticles, it was found that under this situation the surface of BSA took the negative charge, but the magnetic nanoparticles took the positive charge. Due to the small diameter, the adsorption equilibrium of BSA onto the nanoparticles reached very quickly within 10 min. The adsorption equilibrium of BSA onto the magnetic chitosan nanoparticles fitted well with the Freundlich model. The experimental results showed that the magnetic chitosan nanoparticles have potential to be used for the quick pretreatment in the protein analysis process.     

Albumin microspheres as carriers for the antiarthritic drug celecoxib

The present study investigates the preparation of celecoxib-loaded albumin microspheres and the biodistribution of technetium-99m (^99mTc)-labeled celecoxib as well as its microspheres after intravenous administration. Microspheres were prepared using a natural polymer BSA using emulsification chemical cross-linking method. The prepared microspheres were characterized for entrapment efficiency, particle size, and in vitro drug release. Surface morphology was studied by scanning electron microscopy. Biodistribution studies were performed by radiolabeling celecoxib (CS) and its microspheres (CMS) using^99mTc and injecting arthritic rats intravenously. The geometric mean diameter of the microspheres was found to be 5.46 μm. In vitro release studies indicated that the microspheres sustained the release of the drug for }6 days. Radioactivity measured in different organs after intravenous administration of celecoxib solution showed a significant amount of radioactivity in the liver and spleen. In case of celecoxib-loaded microspheres, a significant amount of radioactivity accumulated in the lungs. No significant difference (P>.1) in the radioactivity was observed between the inflamed joint and the noninflamed joint following intravenous injection of^99mTc-CS. However, in case of the microspheres (CMS), the radioactivity present in the inflamed joint was 2.5-fold higher than in the noninflamed joint. The blood kinetic studies revealed that celecoxib-loaded albumin microspheres exhibited prolonged circulation than the celecoxib solution.     

Iron-rich particles in European eel (Anguilla anguilla L.)

Magnetic material in the European eel (Anguilla anguilla L.) was investigated by a combination of magnetic susceptibility measurements, energy dispersive X-ray fluorescence analysis and transmission electron microscopy. It was shown that the magnetic material is associated with iron. The main part of the iron is present in the form of iron-rich particles with irregular shapes about 100-3000 A large. The structures of magnetite (Fe3O4), hematite (alpha-Fe2O3) and alpha-iron (bcc structure) were identified. The particles are composed of more than one of these phases with magnetite being a minority phase when present. The iron-rich particles found in the eel are different from the materials reported for bacteria or bees.     

Electrospun core-shell nanofibers from homogeneous solution of poly(vinyl alcohol)/bovine serum albumin

We report on the preparation and characterization of core-shell structure of bovine serum albumin (BSA) blended poly(vinyl alcohol) (PVA) composite nanofibers by using electrospinning process. The core-shell structure nanofibers have been electrospun from the homogeneous solution of BSA (as shell) and PVA (as core). The morphology, chemical compositions, structure and thermal properties of the resultant products were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX), high-resolution transmission electron microscopy (HR-TEM), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry, thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS) techniques. The blending ratio of PVA and BSA, molecular weight of BSA and the applied voltage of electrospinning process were observed to be the key influence factors on the formation of core-shell nanofibers structure. Based on the experimental findings, we proposed a possible physical mechanism for the formation of core-shell nanofibers structure of PVA blended BSA composite.     

Effect of additives on the release of a model protein from PLGA microspheres

The purpose of this study was to investigate the effect of 2 additives, poly(ethylene glycol (PEG) 1000 and 1,2,3-tridecanoyl glycerol (tricaprin), on the physico-chemical characteristics and in vitro release of a model protein, bovine serum albumin (BSA), form poly(D,L-lactic-co-glycolic acid) (PLGA) microspheres. BSA-loaded microspheres were prepared by the double emulsion solvent evaporation method. Additives were incorporated into microspheres to modify the release of protein. The addition of PEG 1000 and tricaprin changed the surface characteristics of microspheres from smooth and nonporous to porous and dimpled, respectively. The in vitro release profiles showed that the additives significantly (P<0.05) increased the early-stage release of BSA from microspheres.     

Repair effect of diabetic ulcers with recombinant human epidermal growth factor loaded by sustained-release microspheres

In this study the w/o/w extraction-evaporation technique was adopted to prepare poly(lactic-co-glycolic acid) (PLGA) microspheres loading recombinant human epidermal growth factor (rhEGF). The microspheres were characterized for morphology by transmission electron microscopy (TEM) and particle size distribution. The release performances, the proliferation effects and therapeutic effects of rhEGF-loaded PLGA microspheres were all studied. The results showed that these spherical microspheres had a narrow size distribution and a high drug encapsulation efficiency (85.6%). RhEGF-loaded microspheres enhanced the growth rate of fibroblasts and wound healing more efficiently than pure rhEGF. The number of the proliferating cell nuclear antigen (PCNA) in the epidermis layer with the microsphere treatment was significantly larger than those of the control groups. Overall locally sustained delivery of rhEGF from biodegradable PLGA microspheres may serve as a novel therapeutic strategy for diabetic ulcer repair.